AP1240 discovers but does not join WLC2006

Hello,
WLC2006 and AP1240 are connected to the same subnet. WLC2006 addresses are 192.168.24.18 port 1 for the management interface and 192.168.24.25 port 2 for the ap-manager interface (see <<wlc_config_070105_145300.txt>> issued from show run-config). AP address is 192.168.24.20 and the controller address is 192.168.24.18.
The discovery phase seems OK. Then the AP sends a CNTL JOIN_REQUEST. No answer is provided by the WLC which acts as if it does not receive the request (see WLC traces <<wlc_070105_123000.txt>> and AP traces <<ap_070105_123000.txt>>). Ethereal traces captured on the same hub than WLC are attached (<<ethereal_070105_172400.txt>>).
What is badly set in the configurations?
Thanks by advance for your help.
Alain-Claude
Attached files:
<<wlc_config_070105_145300.txt>>
<<wlc_070105_123000.txt>>
<<ap_070105_123000.txt>>
<<ethereal_070105_172400.txt>>

Hi,
The port of the ap-manager interface has been changed from 2 to 1. It is better and the AP joins now the WLC. But a problem occurs in the state IMAGE.
AP traces are:
*Mar 1 00:00:36.071: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
examining image...
Loading file /c1240...
*Jan 8 16:10:41.113: %LWAPP-5-CHANGED: LWAPP changed state to IMAGE
%Error opening (Protocol error)archive download: takes 6 seconds
*Jan 8 16:10:47.113: LWAPP_CLIENT_ERROR_DEBUG: Retransmission count for packet exceeded more than max(IMAGE_DATA , 1)
*Jan 8 16:10:47.113: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 8 16:10:47.114: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 8 16:10:47.116: LWAPP_CLIENT_ERROR: not receive read response(3)
*Jan 8 16:10:47.120: lwapp_image_proc: unable to open tar file
*Jan 8 16:10:47.155: %SYS-5-RELOAD: Reload requested by lwapp image download proc. Reload Reason: Reason unspecified.
*Jan 8 16:10:47.155: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
WLC traces are:
Mon Jan 8 16:09:38 2007: Successfully transmission of LWAPP Join-Reply to AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:40 2007: Received LWAPP IMAGE_DATA from AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:40 2007: Refusing image download to AP 00:19:2f:7e:53:02 - Unable to open file /bsn/ap//c1240
Mon Jan 8 16:09:40 2007: Processing of Image Data failed from AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:41 2007: Received LWAPP IMAGE_DATA from AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:41 2007: Failed decryption of message from AP 00:19:2F:7E:53:02
Mon Jan 8 16:09:41 2007: Security processing of Image Data failed from AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:42 2007: Received LWAPP IMAGE_DATA from AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:42 2007: Failed decryption of message from AP 00:19:2F:7E:53:02
Mon Jan 8 16:09:42 2007: Security processing of Image Data failed from AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:43 2007: Received LWAPP IMAGE_DATA from AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:43 2007: Failed decryption of message from AP 00:19:2F:7E:53:02
Mon Jan 8 16:09:43 2007: Security processing of Image Data failed from AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:44 2007: Received LWAPP IMAGE_DATA from AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:44 2007: Failed decryption of message from AP 00:19:2F:7E:53:02
Mon Jan 8 16:09:44 2007: Security processing of Image Data failed from AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:45 2007: Received LWAPP IMAGE_DATA from AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:45 2007: Failed decryption of message from AP 00:19:2F:7E:53:02
Mon Jan 8 16:09:45 2007: Security processing of Image Data failed from AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:46 2007: Received LWAPP DISCOVERY REQUEST from AP 00:19:2f:7e:53:02 to 00:0b:85:47:df:80 on port '1'
Mon Jan 8 16:09:46 2007: spamDeleteLCB: stats timer not initialized for AP 00:19:2f:7e:53:02
Mon Jan 8 16:09:46 2007: Successful transmission of LWAPP Discovery-Response to AP 00:19:2f:7e:53:02 on Port 1
What does that mean?
Thanks for your help
Best Regards,
Alain-Claude

Similar Messages

  • Does not join to any fact source issue in 10g

    HI,
    I am getting below issue while compiling rpd.
    Logical Dimension Table Dim-XX has a source xx_aa that does not join to any fact source.
    Let me describe situation here.
    In physical layer , i have one xx_v table . there is no join condition physical layer. But in BMM layer we have created two logical tables for single xx_v table and providing join in bmm layer. When am compiling it i'm getting an error.
    The one which i have using current rpd, same rpd in production with out any warnings(Logical Dimension Table Dim-XX has a source xx_aa that does not join to any fact source) and they don't have any logical level mapping in content tab. But i am using same rpd in dev instance getting warnings.
    Thanks,
    Mal
    Edited by: user10675696 on Feb 11, 2013 3:08 AM

    Hi Srini,
    Please find the below warning here and we don't have an hierarchy for MTL_SYSTE_ITEMS_B
    [39008] Logical dimension table Mtl System Items B has a source MTL_SYSTEM_ITEMS_B that does not join to any fact source.
    I am getting this in Dev instance only but not in Production. But one rpd can be used in dev and production instances.
    Thanks,
    Mall

  • Newly added discoverer responsibility does not open the workbook sheets

    Adding reports to newly added discoverer responsibility does not open the workbook sheets
    Actually its a new responsibility where i add existing workbook, also shared the business area but when trying to execute the report through my user firstly it says "Workbbok cannot be expanded, Unable to open workbook" later when i close the page i get the below error
    “Contact with the Discover server has been lost. To continue with your work, please restart Discoverer Plus. If this problem persists, please contact your Oracle Application Server Administrator” error message.
    Please suggest.

    Hi,
    You need to run a trace for this user to diagnose this issue. Look at note 133055.1 for more details.
    Rod West

  • Discoverer Reports does not work in Multi-org Environment after R12 Upgrade

    Discoverer Reports does not work in Multi-org Environment after R12 Upgrade. Created a simple report using the below query:
    SELECT po_header_id, segment1, type_lookup_code
    FROM po_headers
    WHERE segment1 = '5000002'
    Query works perfectly fine; when i set the ORG_CONTEXT in the database using the command:
    EXEC mo_global.set_policy_context('S',129)
    But the report doesn't fetch any data when ran from an Org based responsibility. We've ensured that the MO: Operting Unit is set accurately and general Oracle reports (PLSQL Program OR XML Publisher) are working perfectly fine.
    ===========
    I followed the steps provided in Metalink Note: 732826.1 - It works for some responsibilities where the MO: Security Profile is not set; but fails for those responsibilities where the MO: Security Profile is set.
    I am looking for specific solution that works irrespective of either the MO: Operating Unit profile is set of not.
    Please suggest. Appreciate your response.
    Thanks,
    Kesava Chunduri

    Hi Hussein,
    Thanks for the quick response.
    Yes, I've gone thru both the notes specified below:
    Discoverer Workbooks Based On Organization Enabled Views Are Not Populated [ID 1293438.1]
    - Tried this option; but this option is messing up a couple of Oracle Standard Functionalities.
    - For ex: If i set this profile option; we are not able to create any receipts using Custom Responsibilities.
    I am able to create the receipt, when i remove this profile option.
    No Data Shows for Reports in Discoverer 10g with Applications Release 12 [ID 1054380.1]
    - I see that the products i am running these reports from AR/GL - already exists in these tables.
    Anything other options??
    Thanks,
    Kesava

  • AIR-CAP3502I-E-K9 does not join preferred controller

    I have an AIR-CAP3502I-E-K9 AP that is configured for two WLAN controllers with preferred order. However the AP does not join the primary controller, but uses the secondary one instead. I have a bunch of these AIR-CAP3502I-E-K9s , majority work fine, but three of them not.
    I have tried commands according to
    https://supportforums.cisco.com/docs/DOC-24917
    In the controller's GUI  the order is properly configured. I also tried to use 'Clear All Config" option on the controller and configured the AP from the scratch, but this did not help.
    Here is what I have
    XXXX#sh capwap client config
    configMagicMark         0xF1E2D3C4
    chkSumV2                30883
    chkSumV1                1073
    swVer                   7.2.111.3
    adminState              ADMIN_ENABLED(1)
    name                    XXXX
    location                YYYY
    group name
    mwarName                ZZZZ1
    mwarIPAddress           192.168.1.1
    mwarName                ZZZZ2
    mwarIPAddress           192.168.1.2
    mwarName
    mwarIPAddress           0.0.0.0
    ssh status              Enabled
    Telnet status           Enabled
    numOfSlots              2
    spamRebootOnAssert      1
    spamStatTimer           180
    randSeed                0xBAC2
    transport               SPAM_TRANSPORT_L3(2)
    transportCfg            SPAM_TRANSPORT_DEFAULT(0)
    initialisation          SPAM_PRODUCTION_DISCOVERY(1)
    ApMode                  Local
    ApSubMode               Not Configured
    AP Rogue Detection Mode Enabled
    OfficeExtend AP         [0] Disabled
    OfficeExtend AP JoinMode[0] Standard
    Discovery Timer         10 secs
    Heart Beat Timer        30 secs
    Led State Enabled       1
    Primed Interval         0
    AP ILP Pre-Standard Switch Support Disabled
    AP Power Injector Disabled
    Infrastructure MFP validation Disabled
    Configured Switch 1 Addr 192.168.1.2
    Configured Switch 2 Addr 192.168.1.1
    non-occupancy channels:
    Ethernet (Duplex/Speed) auto/auto
    *Mar  1 00:14:23.001: %CAPWAP-3-ERRORLOG: Selected MWAR 'ZZZZ2'(index 1).
    *Mar  1 00:14:23.001: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Aug 22 12:21:57.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
    *Aug 22 12:21:57.581: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
    *Aug 22 12:21:57.581: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    My primary one is 192.168.1.1 and secondary is 192.168.1.2, but the AP joins always the secondary one.
    The lines above
    Configured Switch 1 Addr 192.168.1.2
    Configured Switch 2 Addr 192.168.1.1
    seem to be suspicious, I would expect the reverse order, but do not know how the code did it.
    The only guess is that in the very beginning the AP joined 192.168.1.2, and this was the controller I configured the AP initially from. The AP seems to maybe somehow remember this.
    OS version is
    swVer                   7.2.111.3
    Thanks,
    Vlad

    Yes, this is what I am trying all the time - configure the AP to point to the WLCs I want it to join.
    Firstly I did through GUI, did not work.
    Secondly I  used 'Clear All Config" option on the controller and configured the AP from the scratch through GUI, did not work.
    Thirdly I tried through command line on the AP, did not work.
    I used these commands
    XXXX#capwap ap  primary-base ZZZZ1 192.168.1.1
    XXXX#capwap ap  secondary-base ZZZZ2 192.168.1.2
    XXXX#sh capwap client config
    configMagicMark         0xF1E2D3C4
    chkSumV2                30883
    chkSumV1                1072
    swVer                   7.2.111.3
    adminState              ADMIN_ENABLED(1)
    name                    XXXX
    location                YYYY
    group name
    mwarName                ZZZZ1
    mwarIPAddress           192.168.1.1
    mwarName                ZZZZ2
    mwarIPAddress           192.168.1.2
    mwarName
    mwarIPAddress           0.0.0.0
    ssh status              Enabled
    Telnet status           Enabled
    numOfSlots              2
    spamRebootOnAssert      1
    spamStatTimer           180
    randSeed                0xBAC2
    transport               SPAM_TRANSPORT_L3(2)
    transportCfg            SPAM_TRANSPORT_DEFAULT(0)
    initialisation          SPAM_PRODUCTION_DISCOVERY(1)
    ApMode                  Local
    ApSubMode               Not Configured
    AP Rogue Detection Mode Enabled
    OfficeExtend AP         [0] Disabled
    OfficeExtend AP JoinMode[0] Standard
    Discovery Timer         10 secs
    Heart Beat Timer        30 secs
    Led State Enabled       1
    Primed Interval         0
    AP ILP Pre-Standard Switch Support Disabled
    AP Power Injector Disabled
    Infrastructure MFP validation Disabled
    Configured Switch 1 Addr 192.168.1.2
    Configured Switch 2 Addr 192.168.1.1
    non-occupancy channels:
    Ethernet (Duplex/Speed) auto/auto
    XXXX#sh log
    Syslog logging: enabled (1 messages dropped, 8 messages rate-limited,
                    0 flushes, 0 overruns, xml disabled, filtering disabled)
        Console logging: level debugging, 61 messages logged, xml disabled,
                         filtering disabled
        Monitor logging: level debugging, 0 messages logged, xml disabled,
                         filtering disabled
        Buffer logging: level debugging, 67 messages logged, xml disabled,
                        filtering disabled
        Logging Exception size (4096 bytes)
        Count and timestamp logging messages: disabled
        Trap logging: level emergencies, 0 message lines logged
            Logging to 255.255.255.255(global) (udp port 514, audit disabled,  link down), 0 message lines logged, xml disabled,
                   filtering disabled
    Log Buffer (1048576 bytes):
    *Mar  1 00:00:09.424: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:09.434: *** CRASH_LOG = YES
    *Mar  1 00:00:09.434: 64bit PCIE devicesSecurity Core found.
    Base Ethernet MAC address: E0:5F:B9:A8:00:7F
    *Mar  1 00:00:12.482: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:13.731: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:13.797: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:16.996: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
    *Mar  1 00:00:17.052: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)
    *Mar  1 00:00:17.068:  status of voice_diag_test from WLC is false
    *Mar  1 00:00:19.182: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(25e)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2012 by Cisco Systems, Inc.
    Compiled Fri 14-Sep-12 19:13 by prod_rel_team
    *Mar  1 00:00:19.182: %SNMP-5-COLDSTART: SNMP agent on host XXXX is undergoing a cold start
    *Mar  1 00:13:33.342: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:13:33.342: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:13:33.493:  status of voice_diag_test from WLC is false
    *Mar  1 00:13:33.632: %SSH-5-ENABLED: SSH 2.0 has been enabledlwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:13:33.956: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:13:34.343: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:13:34.343: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:13:36.029: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:13:41.484: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.21, mask 255.255.255.0, hostname XXXX
    *Mar  1 00:13:51.981: Logging LWAPP message to 255.255.255.255.
    *Mar  1 00:14:01.997: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:14:06.099: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:14:07.190: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:14:08.191: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 00:14:08.288: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:14:09.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:14:11.000: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
    *Mar  1 00:14:23.001: %CAPWAP-3-ERRORLOG: Selected MWAR 'ZZZZ2'(index 1).
    *Mar  1 00:14:23.001: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Aug 23 06:07:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
    *Aug 23 06:07:13.578: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
    *Aug 23 06:07:13.578: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Aug 23 06:07:14.025: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
    *Aug 23 06:07:14.091: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Aug 23 06:07:14.094: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller ZZZZ2
    *Aug 23 06:07:14.154: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    What I think might be the key to the problem is this
    Configured Switch 1 Addr 192.168.1.2
    Configured Switch 2 Addr 192.168.1.1
    This is not changing no matter what I do.
    Thanks,
    Vlad

  • [39008] Logical dimension table has a source that does not join to any fact

    Dear reader,
    After deleting a fact table from my physical layer and deleting it from my business model I'm getting an error: [39008] Logical dimension table TABLE X has a source TABLE X that does not join to any fact source. I do have an other fact table in the same physical model and in the same business model wich is joined to TABLE X both in the physical and business model.
    I cannot figure out why I'm getting this error, even after deleting all joins and rebuilding the joins I'm getting this error. When I look into the "Joins Manager" these joins both in physical as well as logical model do exist, but with consistency check it warns me about [39008] blabla. When I ignore the warning and go to answers and try to show TABLE X (not fact, but dim) it gives me the following error.
    Odbc driver returned an error (SQLExecDirectW).
    Error Details
    Error Codes: OPR4ONWY:U9IM8TAC:OI2DL65P
    State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 14026] Unable to navigate requested expression: TABLE X.column X Please fix the metadata consistency warnings. (HY000)
    SQL Issued: SELECT TABLE X.column X saw_0 FROM subject area ORDER BY saw_0
    There is one *"special"* thing about this join. It is a complex join in the physical layer, because I need to do a between on dates and a smaller or equal than current date like this example dim.date between fact.date_begin and fact.date_end and dim.date <= current_date. In the business model I've got another complex join
    Any help is kindly appreciated!

    Hi,
    Have you specified the Content level of the Fact table and mapped it with the dimension in question? Ideally this should be done by default since one of the main features of the Oracle BI is its ability to determine which source to use and specifying content level is one of the main ways to achieve this.
    Another quick thing that you might try is creating a dimension (hierarchy) in case it is not already present. I had a similar issue few days back and the warning was miraculously gone by doing this.
    Regards

  • Error 39008: logical table does not join to fact source

    About to lose my mind over this error!
    I'm told logical table IT_WORK_ITEM_D (a dimension) does not join to any fact source, although it should show as joined to IT_WORK_ITEM_DSNPSHT_F
    - I have verified the physical joins
    - I have verified the business model joins
    - I have created hierarchies for all logical tables joined to the fact (IT_WORK_ITEM_DSNPSHT_F)
    - I have checked the Content tab for the fact table and ensured that the logical dimension is set to the lowset level.
    Suggestions from here?
    -John

    This was helpful, although it did not solve the problem immediately.
    After much consistency checking, I cleared out some of the content assignments and that seemed to work (after having not worked). I still don't feel like I identified the core problem, but it is working now.
    -John

  • Logical table does not join to any logical table

    HI,
    I want to implement Business Unit hierarchy for drill down in OBIEE  so I’ve created a custom table with the hierarchy information,
    I’ve imported that table in the out-of the box physical schema & defined a relationship between the W_ORG_D table & my custom INVENTRY_ORG table as INVENTRY_ORG.BU_ID = W_ORG_D. VIS_PR_BU_ID* but when I try to check in my changes I’m getting the following error.*
    Logical table INVENTRY_ORG does not join to any logical table.
    Kindly let me know how to resolve this error.One more doubt i have is can we import custom tables in the out of the box OBIEE mappings for SIEBEL..that is the core subject area.
    Thanks,

    Hi user10340125 ,
    1) I think you have joined tables in physical layer, but you have not created complex join in logical layer.
    Check your consistency and see what warnings you are getting.
    2) Yes you can import custom tables in whatever subject area. Once you imported tables in physical layer, then they all are just objects, so you can freely play around with them. Just for best practices, make sure you follow proper naming convention for custom tables and columns..
    - Vinay

  • [39008] Logical dimension table X has a source that does not join to any...

    Hi Gurus,
    I have warning:
    "[39008] Logical dimension table X has a source that does not join to any fact source"
    WHERE X:
    PROMOTIONS,PRODUCTS, CUSTOMERS, CHANNELS
    but all logical table are mapped to fact.
    Eveb I can create reports for them
    (The metadata was derived from OWB 11gR2, SALES_EE)
    Thanks
    Laszlo
    Thanks for Your earlier answer as well!

    Hi,
    Did you create hierrarchy on that dimension.?
    Add contel level in fact source to hierarrchy detail for the fact that joins the dimension.
    Look at this for best practice...http://gerardnico.com/wiki/dat/obiee/hierarchy?s
    Please do close your previous thread assigning points by clicking helpful or correct to the replies
    Import XML file into rpd file
    Thanks,
    Srikanth

  • [39008] Logical dimension table has a source  that does not join to any fac

    Hi
    I have a problem in BMM layer:
    *[*39008] Logical dimension table X has a source Y that does not join to any fact source.*
    To start with I have three tables joining to Cust (customer) table in physical layer
    Cust-Seg (Segments)-------------------------------->>Cust via segment key
    Cust-Geo (customer Geographics)-------------->>Cust via address key
    in the BMM layer under the CUST table when I pull in Cust- seg it works fine .
    But it gives an warning [39008] -if iI create a single LTS for the product with the join for all 3 tables
    The Same warning appears when i import th Cust -seg table as Logical table

    Have you tried this?
    http://obiee11gqna.blogspot.com/2011/02/obiee-error-39008.html

  • Logical Dimension tabel does not join to any fact source

    I want to create a new “Dimension” table. This will be an Account Geographic dimension. My Business and Physical model are setup as follows:
    1.     Account Address (WC_ADDR_F) is joined to Account (W_ORG_D) which is joined to multiple Fact tables (Ex: Order Item (W_ORDERITEM_F)
    2.     When I perform “Global Consistency” check it comes back with no errors or warnings.
    I create the Account Geographic dimension as follows:
    1.     I right click on the subject area and select New Object->Dimension and name it “Account Geographic Dimension”. I do not select or change anything else.
    2.     I right click on the new dimension and select New Object->Logical Level. I name the level “All” and check the “Grand total level” check box. Nothing else is changed.
    3.     I right click on the “All” level and select New Object->Child Level. I name the level “Country”, set number of elements to 200.
    4.     I right click on the “Country” level and select New Object->Child Level. I name the level “State”, set number of elements to 250.
    5.     I drag the “Country” element from the Logical table (Account Address) to the “Country Level” on the new Dimension (Account Geographic Dimension)
    6.     I drag the “State” element from the Logical table (Account Address) to the “State Level” on the new Dimension (Account Geographic Dimension)
    7.     I then select the “Country” level properties and add a new key. For the key I select the “Country” column that I just dragged up there.
    8.     I then select the “State” level properties and add a new key. For the key I select the “State” column that I just dragged up there.
    My goal is that when an Analyst selects the “Country” column in Answers from the “Account Address” area that the user would be able to drill down from “Country” to “State”.
    When I perform “Global Consistency” I now get the following warning:
    WARNINGS:
    BUSINESS MODEL CCCi Analytics:
    [39008] Logical dimension table Account Address has a source CCCi_Dim_WC_ADDR_F_AccountAddress that does not join to any fact source.
    Why do I now get an error no the Account Address table for not connecting to a Fact table? The error message references the “Account Address” dimension table which I believe is the source to the Account Geographic Dimension. If this is the source table, why did it not get a warning message before I created the new dimension?
    Thanks…

    Here is the solution that I was able to get to work:
    1.     I did not have to reduce the business model to a star but was able to keep it a snowflake
    Final design (which was same as the original) here is the Business Model (snowflake schema)
    1.     Account Hierarchy (logical) -> Account (logical) -> Order Item Fact
    2.     Account Address (logical) -> Account (logical) -> Order Item Fact
    In this model the logical tables Account Hierarchy and Account Address snowflake off of the Account table which joins to the Fact table. I then:
    1.     Created an “Account” dimension
    2.     Created a child “Account Total” level
    3.     Created two (2) children off of the “Account Total” level: (1) Account Address Country and (2) Account Hierarchy Top Level
    a.     Key for “Account Address Country” was the Country column from Account Address (logical)
    b.     Key for “Account Hierarchy Top Level” was the Top Level Account Name from Account Hierarchy (logical)
    4.     Off of “Account Address Country”:
    a.     Created a (1) child off of “Account Address Country” called “Account Address State” with the State field from the Account Address (logical) as the key
    b.     Created a (1) child off of “Account Address State” called “Account Address Detail” with the ROW_WID from the Account Address (logical) as the key
    c.     Created a (1) child off of “Account Address Detail” with the ROW_WID from the Account (logical) as the key
    5.     Off o “Account Hierarchy Top Level”:
    a.     Created a (1) child off of “Account Hierarchy Top Level” called “Account Hierarchy Level 1” with the Top Account ID from Account Hierarchy (logical) as the key
    b.     Created (1) child off of “Account Hierarchy Level 1” called “Account Hierarchy Detail” with the ROW_WID from “Account Hierarchy” as the key
    c.     Crated a (1) child off of “Account Hierarchy Detail” with the ROW_WID from the Account (logical) as the key
    The global consistency check completed with no errors or warning with this design. It appears that perhaps you need to have all of the logical table keys in the dimension path that trace to the Fact table. One other note, cannot repeat use of other columns in the dimension except for the key of the first logical table.
    Please let me know if I missed something.

  • Source does not join to any fact source

    I created a new dimension as follows:
    1) Mapped Source from OLTP to Physical Layer
    2) Created Alias for source
    3) Create physical "Few Foreign Key" join between new source table and existing table (key to key)
    4) Run consistency check with no issues.
    5) Create new Logical table
    6) Create new complex logical join between same two tables in Business Model
    7) Join is a Right Outer Join
    8) Run consistency check and receive the following warning message.
    Can you please help me resolve? Thanks...
    WARNINGS:
    BUSINESS MODEL Marketing Contact List:
    [39008] Logical dimension table OLTP Personal Communication has a source S_PER_COMM_ADDR that does not join to any fact source.

    I'm still a bit confused:
    Here are the steps that I understand:
    1) Create Physical Alias Table (Personal Communication)
    2) Create Physical Join between Personal Communication and Contact
    3) Create Logical Table (Personal Communication) with physical source Personal Communication
    4) Create Business Model Join between Personal Communication and Contact (right outer with Contact on right)
    If i save now i get the warning message as described at the beginning.
    The Business Model look like this:_
    OLTP = Source of table is OLTP database
    DW = Source of table is Data Warehouse
    Personal Communication(OLTP Table)->Contacts(OLTP table)->Campaign Promotion(OLTP Table)->Contact Fact(DWTable)
    In addition to the Contacts (OLTP) table that joins to Campaign Promotion the following other tables join to Campaign Promotion: Prospects (OLTP)
    The Contact Fact table has 5 tables joined to it: Order, Service Request, Order Item Attr, Account, and Ordered Product
    There are 5 Dimension Hierarchies (all created from the DW tables): Account, Contact, Order, Order Item Attr, and Ordered Product
    I then try to recreate the steps indicated:
    5) Right click on the new Logical Table (Personal Communication). which generates another Dimension Hierarchy: ContactDim
    Since the other logical tables created from OLTP sources do not have hierarchy dimensions created I'm not sure why I'm doing this here. If someone could explain I would appreciate it?
    If I select the properties for ContactDim:
    a) The default root level = Contact Total
    b) Tables listed are: Prospects (OLTP), Campaign Promotion (OLTP), Contact (DW), Contacts (OLTP), and Personal Communication (OLTP)
    If I expand the ContactDim dimension I have a Contact Total:
    Grand total level checked
    Child Levels: Prospects (OLTP), Contacts (OLTP), Personal Communication (OLTP)
    I then have sources for each of these below this with all fields listed and additional lists below that.
    I'm stuck here and am not sure what to do. I really don't want any drill down capability but I want to elimenate the Warning message that I was getting before.
    Thanks for any help that you can provide...

  • Connect to Oracle Discoverer window does not appear

    Hi,
    The Web based Oracle Discoverer 4i does not work properly on my system. I first connect my Microsoft IE to the URL. One the URL there is magnifier icon. Under this icon there is a lable of "Click the image above to start".
    I click this icon and another window pup up. The top left corner of this window shows "Oracle Discoverer" title. Under this title bar are the menu items. The menu items are File,Edit,Sheet,tools, Graph & Help from left to right. The bottom left corner shows "Loading...". But the "Connect to Oracle Discoverer" window never pups up.
    If I connect my browser to another URL I can get "Connect to Oracle Discoverer " window displayed and log into database.
    What is wrong with my first server?
    Thanks for help.
    Wallace

    I'm only guessing, but I've had similar problems in a few cases with the Microsoft Java Virtual Machine. Try getting Discoverer to run with a different JVM, like Oracle Jinitiator.

  • Node does not join cluster upon reboot

    Hi Guys,
    I have two servers [Sun Fire X4170] clustered together using Solaris cluster 3.3 for Oracle Database. They are connected to a shared storage which is Dell Equallogic [iSCSI]. Lately, I have ran into a weird kind of a problem where as both nodes come up fine and join the cluster upon reboot; however, when I reboot one of nodes then any of them does not join cluster and shows following errors:
    This is happening on both the nodes [if I reboot only one node at a time]. But if I reboot both the nodes at the same time then they successfully join the cluster and everything runs fine.
    Below is the output from one node which I rebooted and it did not join the cluster and puked out following errors. The other node is running fine will all the services.
    In order to get out of this situation, I have to reboot both the nodes together.
    # dmesg output #
    Apr 23 17:37:03 srvhqon11 ixgbe: [ID 611667 kern.info] NOTICE: ixgbe2: link down
    Apr 23 17:37:12 srvhqon11 iscsi: [ID 933263 kern.notice] NOTICE: iscsi connection(5) unable to connect to target SENDTARGETS_DISCOVERY
    Apr 23 17:37:12 srvhqon11 iscsi: [ID 114404 kern.notice] NOTICE: iscsi discovery failure - SendTargets (010.010.017.104)
    Apr 23 17:37:13 srvhqon11 iscsi: [ID 240218 kern.notice] NOTICE: iscsi session(9) iqn.2001-05.com.equallogic:0-8a0906-96cf73708-ef30000005e50a1b-sblprdbk online
    Apr 23 17:37:13 srvhqon11 scsi: [ID 583861 kern.info] sd11 at scsi_vhci0: unit-address g6090a0887073cf961b0ae505000030ef: g6090a0887073cf961b0ae505000030ef
    Apr 23 17:37:13 srvhqon11 genunix: [ID 936769 kern.info] sd11 is /scsi_vhci/disk@g6090a0887073cf961b0ae505000030ef
    Apr 23 17:37:13 srvhqon11 scsi: [ID 243001 kern.info] /scsi_vhci (scsi_vhci0):
    Apr 23 17:37:13 srvhqon11 /scsi_vhci/disk@g6090a0887073cf961b0ae505000030ef (sd11): Command failed to complete (3) on path iscsi0/[email protected]:0-8a0906-96cf73708-ef30000005e50a1b-sblprdbk0001,0
    Apr 23 17:46:54 srvhqon11 svc.startd[11]: [ID 122153 daemon.warning] svc:/network/iscsi/initiator:default: Method or service exit timed out. Killing contract 41.
    Apr 23 17:46:54 srvhqon11 svc.startd[11]: [ID 636263 daemon.warning] svc:/network/iscsi/initiator:default: Method "/lib/svc/method/iscsid start" failed due to signal KILL.
    Apr 23 17:46:54 srvhqon11 svc.startd[11]: [ID 748625 daemon.error] network/iscsi/initiator:default failed repeatedly: transitioned to maintenance (see 'svcs -xv' for details)
    Apr 24 14:50:16 srvhqon11 svc.startd[11]: [ID 694882 daemon.notice] instance svc:/system/console-login:default exited with status 1
    root@srvhqon11 # svcs -xv
    svc:/system/cluster/loaddid:default (Oracle Solaris Cluster loaddid)
    State: offline since Tue Apr 23 17:46:54 2013
    Reason: Start method is running.
    See: http://sun.com/msg/SMF-8000-C4
    See: /var/svc/log/system-cluster-loaddid:default.log
    Impact: 49 dependent services are not running:
    svc:/system/cluster/bootcluster:default
    svc:/system/cluster/cl_execd:default
    svc:/system/cluster/zc_cmd_log_replay:default
    svc:/system/cluster/sc_zc_member:default
    svc:/system/cluster/sc_rtreg_server:default
    svc:/system/cluster/sc_ifconfig_server:default
    svc:/system/cluster/initdid:default
    svc:/system/cluster/globaldevices:default
    svc:/system/cluster/gdevsync:default
    svc:/milestone/multi-user:default
    svc:/system/boot-config:default
    svc:/system/cluster/cl-svc-enable:default
    svc:/milestone/multi-user-server:default
    svc:/application/autoreg:default
    svc:/system/basicreg:default
    svc:/system/zones:default
    svc:/system/cluster/sc_zones:default
    svc:/system/cluster/scprivipd:default
    svc:/system/cluster/cl-svc-cluster-milestone:default
    svc:/system/cluster/sc_svtag:default
    svc:/system/cluster/sckeysync:default
    svc:/system/cluster/rpc-fed:default
    svc:/system/cluster/rgm-starter:default
    svc:/application/management/common-agent-container-1:default
    svc:/system/cluster/scsymon-srv:default
    svc:/system/cluster/sc_syncsa_server:default
    svc:/system/cluster/scslmclean:default
    svc:/system/cluster/cznetd:default
    svc:/system/cluster/scdpm:default
    svc:/system/cluster/rpc-pmf:default
    svc:/system/cluster/pnm:default
    svc:/system/cluster/sc_pnm_proxy_server:default
    svc:/system/cluster/cl-event:default
    svc:/system/cluster/cl-eventlog:default
    svc:/system/cluster/cl-ccra:default
    svc:/system/cluster/ql_upgrade:default
    svc:/system/cluster/mountgfs:default
    svc:/system/cluster/clusterdata:default
    svc:/system/cluster/ql_rgm:default
    svc:/system/cluster/scqdm:default
    svc:/application/stosreg:default
    svc:/application/sthwreg:default
    svc:/application/graphical-login/cde-login:default
    svc:/application/cde-printinfo:default
    svc:/system/cluster/scvxinstall:default
    svc:/system/cluster/sc_failfast:default
    svc:/system/cluster/clexecd:default
    svc:/system/cluster/sc_pmmd:default
    svc:/system/cluster/clevent_listenerd:default
    svc:/application/print/server:default (LP print server)
    State: disabled since Tue Apr 23 17:36:44 2013
    Reason: Disabled by an administrator.
    See: http://sun.com/msg/SMF-8000-05
    See: man -M /usr/share/man -s 1M lpsched
    Impact: 2 dependent services are not running:
    svc:/application/print/rfc1179:default
    svc:/application/print/ipp-listener:default
    svc:/network/iscsi/initiator:default (?)
    State: maintenance since Tue Apr 23 17:46:54 2013
    Reason: Restarting too quickly.
    See: http://sun.com/msg/SMF-8000-L5
    See: /var/svc/log/network-iscsi-initiator:default.log
    Impact: This service is not running.
    ######## Cluster Status from working node ############
    root@srvhqon10 # cluster status
    === Cluster Nodes ===
    --- Node Status ---
    Node Name Status
    srvhqon10 Online
    srvhqon11 Offline
    === Cluster Transport Paths ===
    Endpoint1 Endpoint2 Status
    srvhqon10:igb3 srvhqon11:igb3 faulted
    srvhqon10:igb2 srvhqon11:igb2 faulted
    === Cluster Quorum ===
    --- Quorum Votes Summary from (latest node reconfiguration) ---
    Needed Present Possible
    2 2 3
    --- Quorum Votes by Node (current status) ---
    Node Name Present Possible Status
    srvhqon10 1 1 Online
    srvhqon11 0 1 Offline
    --- Quorum Votes by Device (current status) ---
    Device Name Present Possible Status
    d2 1 1 Online
    === Cluster Device Groups ===
    --- Device Group Status ---
    Device Group Name Primary Secondary Status
    --- Spare, Inactive, and In Transition Nodes ---
    Device Group Name Spare Nodes Inactive Nodes In Transistion Nodes
    --- Multi-owner Device Group Status ---
    Device Group Name Node Name Status
    === Cluster Resource Groups ===
    Group Name Node Name Suspended State
    ora-rg srvhqon10 No Online
    srvhqon11 No Offline
    nfs-rg srvhqon10 No Online
    srvhqon11 No Offline
    backup-rg srvhqon10 No Online
    srvhqon11 No Offline
    === Cluster Resources ===
    Resource Name Node Name State Status Message
    ora-listener srvhqon10 Online Online
    srvhqon11 Offline Offline
    ora-server srvhqon10 Online Online
    srvhqon11 Offline Offline
    ora-stor srvhqon10 Online Online
    srvhqon11 Offline Offline
    ora-lh srvhqon10 Online Online - LogicalHostname online.
    srvhqon11 Offline Offline
    nfs-rs srvhqon10 Online Online - Service is online.
    srvhqon11 Offline Offline
    nfs-stor-rs srvhqon10 Online Online
    srvhqon11 Offline Offline
    nfs-lh-rs srvhqon10 Online Online - LogicalHostname online.
    srvhqon11 Offline Offline
    backup-stor srvhqon10 Online Online
    srvhqon11 Offline Offline
    cluster: (C383355) No response from daemon on node "srvhqon11".
    === Cluster DID Devices ===
    Device Instance Node Status
    /dev/did/rdsk/d1 srvhqon10 Ok
    /dev/did/rdsk/d2 srvhqon10 Ok
    srvhqon11 Unknown
    /dev/did/rdsk/d3 srvhqon10 Ok
    srvhqon11 Unknown
    /dev/did/rdsk/d4 srvhqon10 Ok
    /dev/did/rdsk/d5 srvhqon10 Fail
    srvhqon11 Unknown
    /dev/did/rdsk/d6 srvhqon11 Unknown
    /dev/did/rdsk/d7 srvhqon11 Unknown
    /dev/did/rdsk/d8 srvhqon10 Ok
    srvhqon11 Unknown
    /dev/did/rdsk/d9 srvhqon10 Ok
    srvhqon11 Unknown
    === Zone Clusters ===
    --- Zone Cluster Status ---
    Name Node Name Zone HostName Status Zone Status
    Regards.

    check if your global devices are mounted properly
    #cat /etc/mnttab | grep -i global
    check if proper entries are there on both systems
    #cat /etc/vfstab | grep -i global
    give output for quoram devices .
    #scstat -q
    or
    #clquorum list -v
    also check why your scsi initiator service is going offline unexpectedly
    #vi /var/svc/log/network-iscsi-initiator:default.log

  • Applet detect new particeipent  but does not show  any output.

    hi,
    I have written one applet which uses AVReceive2 as inner class.
    This applet detects new particepent joined but does not take any action like showing or playing movie.
    I cant understand where I am wrong.

    Doublechecking, KAT ... is the Device Screen looking a bit like the following screenshot?
    Which particular Windows OS are you using? (XP, Vista or 7?)

Maybe you are looking for

  • Getting the NullPointerException,while merging the pdf files.

    I am getting the following exception, while merging the pdf files with PDFDocMerger class. [121807_113056749][][EXCEPTION] java.lang.NullPointerException at oracle.apps.xdo.template.pdf.PDFWriter.write(PDFWriter.java:62) at oracle.apps.xdo.template.p

  • Error when trying to open, edit & save the document from email link

    Hi, The error occurs when user tries to open the document from the email link (after the document is "shared" with them. The recipient has been given edit rights.  When the document is opened it is opened in read only.  The recipient will click "Edit

  • Acrobat Pro 10

    My client has upgraded to Acrobat pro 10.  I am using Acrobat pro 9.  My client can't read the pdf with embedded and outlined fonts from both indesign and logo done in illustrator.  Client sends me back these pdfs and nothing shows up but one word -

  • Replacing a Server OS with a regular OS Leopard 10.5.6

    Hello All, I've been buying and selling Powermacs. I just one that is a server, and I want to install a regular user version of Leopard OS 10.5.6. Also, there is a software that came with it, that I would like to save. So here's the question: 1. Plea

  • Iphoto '11 lost my iPhone photo download

    Hi, latest iPhoto 9.4.3.   Library in the 'Shared' folder shared with my wife's account.   OSX Lion 10.7.5 Opened iPhoto and proceeded to download the photos off of my iPhone5. When it was done, I selected "Delete photos" as usual. Result:  photos GO