AP1242AG: Telnet and http accesses:

Hi,
I can not telnet the AP1242 and I can not use its web GUI. I do not find the commands to enable Telnet and HTTP (such as "config network telnet / webmode" of the WLC2006). Does anybody provide them.
AP1242 releases are:
* Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.3(11)JA1, RELEASE)
* BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.3(7)JA1, RELEASE SOFTWARE )
* LWAPP image version 4.0.206.0
Thanks by advance. Best Regards,
Alain-Claude

Hi, i belive there is a mistake, since the LWAPP only should work with a wireless lan controller.
http://www.cisco.com/en/US/products/ps6521/products_data_sheet0900aecd8031c968.html
When the LWAPP turns on it locates the WLC by an arp request, and the controller set's up all the configuration on the AP. You can not configure a LWAPP true TELNET or HTTP.
If you only need an AP you should practice a downgrade on your AP to make it work as an autonomous AP.
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Check it Here.......
Hope it helps!!!!

Similar Messages

  • Ftp and http access over XDB repository is not allowed...

    When I try to execute the following command on a reasonably fresh Oracle 11 installation:
    insert into "XMLTEST" ( "name", "xmlfof" ) values ( 'small', DBMS_XDB.GETCONTENTXMLTYPE('/public/small.xml') );
    -- The schema is correctly registered, the file "small.xml" is in the /public repository folder, the user has every conceivable role and priviledge
    -- http access works fine from a remote location, tried to execute the command on the server and from remote system...
    I get the following error message:
    ORA-31020: Der Vorgang ist nicht zulässig, Ursache: For security reasons, ftp and http access over XDB repository is not allowed on server side ORA-06512: in "XDB.DBMS_XDB", Zeile 1915
    Searching for an answer on the forum didn't produce any concreate explanation... Does anyone have any idea how to solve this problem?

    As it turns out, the XML file contained a reference to a DTD at an external web-site, which caused the problem - it was identical to that described here:
    Re: ORA-31020 when using XML with external DTD or entities
    After removing the reference, everything works perfectly...

  • Separate Tomcat http and https access

    Hi
    I got tomcat running both http and https.
    However, http://localhost:8080 and https://localhost:8433 are accessing the same page.
    I need to separate them, to prevent from entering data using http://localhost:8080 by mistake.
    Please help.
    Cheer
    T

    there are 2 ways to only allow https access to your webapp
    1:
    stop tomcat listening on all ports except https port
    2:
    configure your webapp to only allow https access
    http://marc.theaimsgroup.com/?l=tomcat-user&m=104951559722619&w=2

  • Recomended RF Devices for WebSAPConsole (telnet and http modes)

    I'm about to start implementing RF transactions for a client.
    We're using WebSAPConsole with SAPGui 6.4 and SAP ECC 6.0 based on NW2004S.
    I'm looking for a list of make, model and specifications for RF devices that haven been proven to work well with SAPConsole using TelNet server (character mode) or MS IIS server (Gui interface).
    I know that Symbol , Inetrmec and TekLogix have such RF devices.
    But, I want to learn from your experience based on what you have actually used during implementation.
    Could someone provide me this info?

    Hi,  we've been using the character based Intermec Antares T2425 handheld units for the passed 5 years or so.   They work quite well,  and hold up to a lot of abuse. 
    Regards,
    Rich Heilman

  • Sharepoint HTTPS access stopped working suddenly

    Hi,
    we have a single server sharepoint 2013 server.
    HTTP and HTTPS access are enabled for sharepoint site collection. The bindings and aam are set correctly.
    The HTTPS access suddenly stopped working. Might be related to updates installation.
    HTTP access is working properly.
    When I create a new non sharepoint site in IIS the HTTPS access works.
    When I create a new sharepoint site in IIS the HTTPS access does not work only HTTP access is possible. There is no response from the server.
    Following event log error message might be related to this problem:
    Schanel 36888 Error: A fatal alert was generated and sent to the remote endpoint. This may result in termination of the connection. The TLS protocol defined fatal error code is 10. The Windows SChannel
    error state is 1203.
    I checked the ULS, Event logs, changed bindings, tried creating new sharepoint web applications to find the source,
    Any ideas?
    Thanks,
    Andrej

    Hi Andrej,
    I think unless the issue for Schanel 36888 error is fixed,the HTTPS issue may not  get resolve.
    Please refer the below link which was resolved in different OS.
    http://social.technet.microsoft.com/Forums/en-US/9dfb4d09-8096-40c9-ac75-1e23f75417c9/frequent-event-id-36888-windows-schannel-errors-in-the-event-viewer?forum=W8ITProPreRel
    TLS and HTTPS:
    TLS (Transport Layer Security) and SSL (Secure Sockets Layer) are protocols that provide data encryption and authentication between applications and servers in scenarios where that data is being sent across an insecure network, such as checking your email
    (How does the Secure Socket Layer work?).
    http://luxsci.com/blog/ssl-versus-tls-whats-the-difference.html
    http://searchsecurity.techtarget.com/definition/Transport-Layer-Security-TLS
    Please remember to mark your question as answered & Vote helpful,if this solves/helps your problem. 
    s p kumar

  • How to protect both access (http and https) with a Policy Agent

    Hi,
    During the installation of a web Policy Agent (i.e. Policy Agent for IIS) we have to choose the protocol (and port) of the web server we want to protect.
    If we have an IIS with secure (https) and non secure (http) applications, how we manage this scenario with the policy agent?
    Regards,

    Hi,
    Finally, i have installed the agent in IIS5 in the non secure port (http) and in fact it detects both access (http and https) fine.
    The problem now is that if i try to access to a non secure url ( http://mynonsecureapp.com ) all works fine, the agent redirects to https://myaccessmanager.com:443/amserver/UI/Login?goto=http://mynonsecureapp.com but when i try to access to a secure url ( https://mysecureapp.com ) the agent try to redirects me to: https://myaccessmanager.com:443/amserver/UI/Login?goto=http://mysecureapp.com (notice that the agent removes the 's' in the url).
    The amAgent log file shows:
    +2008-07-17 09:44:08.296MaxDebug 656:d8f6b0 PolicyAgent: am_web_is_notification(), https://sigcit.agp.gva.es:443/fullcitriweb is not notification url http://sigcit.agp.gva.es:80/amagent/UpdateAgentCacheServlet?shortcircuit=false.+
    +2008-07-17 09:44:08.296 Warning 656:d8f6b0 PolicyAgent: OnPreprocHeaders(): Access Manager Cookie not found.+
    +2008-07-17 09:44:08.296 Debug 656:d8f6b0 PolicyAgent: am_web_is_access_allowed(): url 'https://sigcit.agp.gva.es:443/fullcitriweb' path_info ''.+
    +2008-07-17 09:44:08.296MaxDebug 656:d8f6b0 PolicyAgent: am_web_is_access_allowed(): processing url http://sigcit.agp.gva.es:80/fullcitriweb.+
    +2008-07-17 09:44:08.296 Debug 656:d8f6b0 PolicyAgent: am_web_is_access_allowed(): client_ip 172.27.65.62 not found in client ip not enforced list+
    Any ideas?
    Regards,
    Edited by: idm_oceanic on Jul 17, 2008 1:33 AM

  • HTTP errors and/or access denied messages preventing me from downloading CS5.5

    How can I download my copy of CS5.5 Design Standard? I keep getting HTTP errors and/or access denied messages.

    Alex5555 where are you downloading the installation files from?  Have you tried utilizing a different web browser?  Is your web browser configured to accept cookies?

  • PORTAL ACCESS  THROUGH HTTP and HTTPS BOTH

    Hi,
    Is it possible to make the portal listen on both http and https ports at the same time? What is the required configuration for the same?
    Please let me know for any other details.
    Any input is highly appreciated.
    regards,
    Chandra

    Hello Chandra,
    you can activate SSL in the J2EE engine and then you have both Protocolls avaliable. The documentaiton can be found at <a href="http://help.sap.com/saphelp_nw04/helpdata/en/f1/2de3be0382df45a398d3f9fb86a36a/frameset.htm">Configuring the Use of SSL on the SAP J2EE Engine</a>.
    Regards
    Gregor

  • Sharepoint foundation 2010 externel https access problems

    I have a very strange problem with my sharepoint foundation 2010 site.
    I have a site which is accessible from outside on https (we have a valid certificate). I configured IIS for http and https.
    Also I configured internal and externel access for this site on sharepoint.
    But sometimes, the site is not accessible from outside on https with (externe.site.fr), BUT  it will be accessible with public ip !!!
    And also accessible from inside. (with interne.intranet.site.fr)
    Any Idea ?
    thanks

    Hi,
    According to your post, my understanding is that your site is not accessible from outside using external host name with https sometimes.
    As your site can be accessible with public IP, however it can’t be accessible from outside using external host name with https sometimes, the issue could be caused by the gateway server in your environment.
    I suggest that you need to check the gateway server configuration.
    For more information, you can refer to:
    http://community.bamboosolutions.com/blogs/sharepoint-2013/archive/2012/12/05/how-to-set-up-microsoft-forefront-unified-access-gateway-environment-for-sharepoint-2013.aspx
    http://nhutcmos.wordpress.com/2013/07/26/configure-ssl-certificate-for-sharepoint-external-https-access/
    http://sharepointdotnetwiki.iblogger.org/2009/12/dns-setup-in-sharepoint/
    http://underthehood.ironworks.com/2010/06/making-a-sharepoint-2010-site-externally-available-alternate-access-mappings-host-header-bindings.html
    Best Regards,
    Yumi Fu

  • Firefox is using large amounts of CPU time and disk access, and I need to know how to shut down most of this so I can actually use the browser.

    Firefox is a very busy piece of software. It's using large amounts of CPU time and disk access. It puts my usage at low priority, so I have to wait for some time to be able to use my pointer or keyboard. I don't know what it uses all that CPU and disk access time for, but it's of no use to me. It often takes off with massive use of resources when I'm not doing anything, and I may not have use of my pointer for several minutes. How can I shut down most of this so I can use the browser to get my work done. I just want to use the web site access part of the software, and drop all the extra. I don't want Firefox to be able to recover after a crash. I just want to browse with a minimum of interference from Firefox. I would think that this is the most commonly asked question.

    Firefox consumes a lot of CPU resources
    * https://support.mozilla.com/en-US/kb/Firefox%20consumes%20a%20lot%20of%20CPU%20resources
    High memory usage
    * https://support.mozilla.com/en-US/kb/High%20memory%20usage
    Check and tell if its working.

  • How to find out list of users and their access on Sharepoint

    Hello Everyone
    How can i find out list of users and what access they have on SharePoint site? I want to create table with list of the users and their access?
    Thanks

    you can get the report using below powershell scripts. first one gives list of users in a site collection level.
    The second link generates the permissions reports for each user.
    http://techtrainingnotes.blogspot.com/2010/12/sharepoint-powershell-script-to-list.html
    https://sp2010userperm.codeplex.com/
    My Blog- http://www.sharepoint-journey.com|
    If a post answers your question, please click Mark As Answer on that post and Vote as Helpful

  • Cannot login to Cisco Jabber 10.5.1 over Mobile and Remote Access

    Hi,
    We have deployed sucessfully VCS Expressway-C and VCS Expressway-E with only 1 zone which is "Unified Communication Traversal" and is for Mobile and Remote Access only. VCS-C and VCS-E are communicating and in statuses everything is active and working. Also VCS-C can communicate with CUCM and CUP (both version 10.5).
    Problem is when I deploy Cisco Jabber 10.5.1 on computer outside of LAN and without VPN it start communicating with VCS-E, ask me for accepting certificate (we have certificate only intenally generated on Windows CA) and after that it is trying to connect and after few seconds it will tell me that it can't communicate with server.
    Did any of you had same problem or can you advice how to troubleshoot? In Jabber logs there is only something like "Cannot authenticate" error message, but when I startup VPN I can authenticate without any problems.
    Thanks

    On Expressway-C are your HTTP Allow Lists setup properly?  By default, and auto discovered CUCM and IMP should be listed via IP and Hostname, but if not, you'll need to insert manually.
    Also, you can look at the config file your Expressway-E would be handing out to Jabber via this method.
    From the internet, browse to:
    https://vcse.yourdomain.com:8443/Y29sbGFiLmNvbQ/get_edge_config?service_name=_cisco-uds&service_name=_cuplogin
    Where:
    vcse is your Expressway-E hostname (or CNAME/A record)
    yourdomain.com is your own domain
    The first directory is your Base64 encoded domain name, remove and trailing equal signs (=)
    The XML returned is basically the DNS SRV record information available as if internal for _cisco-uds and _cuplogin
    TFTP DNS SRV is optional if you configured TFTP in IMP for your Legacy Clients.

  • How to set up full access and limited access wireless networks to laptops

    Dear Apple,
    I just received my Apple 1 TB Time Capsule. Can someone please help me with a network configuration I want to set up?
    I have a cable modem, and, three computers: a G4 iMAC (system 10.5.5), an Apple MacBook (system 10.5.5), and, a PC laptop.
    The Time Capsule is connect directly to the cable modem.
    Regarding the computers:
    (1) I want the G4 iMAC to connect directly, via an Ethernet cable, to the Time Capsule, WITH FULL ALLOWED ACCESS to the Time Capsule and to the back-up function of the Time Machine feature, and, with allowed access to my HP inkjet printer (class 6110);
    (2) I also want the MacBook laptop to wirelessly link to the Time Capsule via the Airport utility on the laptop, and, WITH FULL ALLOWED ACCESS to the Time Capsule and to the back-up function of the Time Machine feature (using WPA/WPA2 security, and, without the network name visible to third parties), and, WITH allowed access to my HP inkjet printer (class 6110);
    (3) I want the PC laptop to wirelessly link to the Time Capsule (using WEP security), but WITHOUT ACCESS to the Time Machine, WITHOUT access to the back-ups on the iMAC, WITHOUT access to the back-ups on the MacBook, and, WITHOUT access to the inkjet printer --- I only want the PC to use the Time Capsule as a WIRELESS ROUTER so that the PC laptop can access the internet.
    (4) And, finally, I want to specify (Time-Capsule/Time-Machine/server ) access ONLY to the iMAC and the MacBook, so that others cannot gain any access.
    I specifically need help to set up and configure the Time Capsule so that the PC laptop, as stated above, should have limited access to the Time Capsule --- namely, only to access the internet, and, not even be aware of stored data on the Time Capsule, not even be aware of the inkjet printer, and, not even see my WPA network name when the PC scans for wireless devices.
    I also want the iMAC and the MacBook to have access to each other’s data stored on the Time Capsule (like a common server).
    I have an old D-Link DI-624 wireless router that I used before buying the Time Capsule, which is available, if needed. Hopefully, I can configure the Time Capsule so that I would not need the old D-Link.
    Thank you in advance,
    David.

    The basic method for remote access is not changed.
    http://gigaom.com/apple/access-your-time-capsule-over-the-internet/
    You have a few issues.
    The really big one.. the school firewall should not let you connect to home.
    Check the IT admin at your school but if they allow anything but a few protocols like http and https through, they are not doing their job. You cannot afford in a large network to have every Tom Dick and Harry access any open device.. that can introduce viruses and trojans into the network behind the firewall.
    The general method for remote access on large networks is vpn and the TC offers no vpn connection.. just AFP.
    If you intend using 3G wireless stick or the like then you can get access.
    The next issue is static public IP or how to find the TC.. you need some way to find the IP if your ISP does not offer static ip, and the tc has no dyndns client. Since Apple shut down new users for mobileme and will close that service there is no method to find the TC IP without owning your own domain. You would be better placing the TC in bridge behind a router that does offer dyndns and port forward AFP (TCP 548) to it.

  • Simultaneously Connecting Multiple Tables of the same Database to Textboxes of the same Form using a single ADO Control Code using VB6 Enterprise Edition and MS Access 2007

    Iv 10 Tables consisting of atleast 10 fields each in a single Database. Bt, Im only able to connect 1 table at a time to a form using an ADO Control. Im able to add data from table 'student' to text-boxes in my form. Bt, hw can I add data from field(0) of
    Table 'Student' to Textbox1 and data from field(0) of Table 'Marks' to Textbox2 using VB6??
    This is the current sample coding iv got to connect a single table to a form:
    Global con As New ADODB.Connection
    Global rs As New ADODB.Recordset
    Public Function Connect()
    If con.State = 1 Then con.Close
    con.Open "Provider=Microsoft.Jet.OLEDB.4.0;Data Source=" + App.Path + "\bca.mdb;Persist Security Info=False"
    End Function
    Private Sub Add_Click()
    If rs.State = 1 Then rs.Close
    rs.Open "select * from student", con, adOpenDynamic, adLockOptimistic
    rs.AddNew
    rs.Fields(0) = (Text1.Text)
    rs.Fields(1) = (Text2.Text)
    rs.Fields(2) = (Text13.Text)
    rs.Fields(3) = (Text4.Text)
    rs.Fields(4) = (Text5.Text)
    rs.Fields(5) = (Text6.Text)
    rs.Fields(6) = (Text7.Text)
    rs.Fields(7) = (Text8.Text)
    rs.Fields(8) = (Text9.Text)
    rs.Fields(9) = (Text10.Text)
    rs.Fields(10) = (Text11.Text)
    rs.Update
    MsgBox " Record Added"
    End Sub
    What can I do to add fields from 2 different tables to different text boxes within the same form using a single ado control using vb6 and MS Access 2007??

    Hi,
    Since VB6 product is not supported in this forum, you may go to these forums for support:
    #Where to post your VB 6 questions
    http://social.msdn.microsoft.com/Forums/en-US/6a0719fe-14af-47f7-9f51-a8ea2b9c8d6b/where-to-post-your-vb-6-questions
    Thank you for your understanding.
    Best regards,
    Franklin
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • My Mac Book  hard drive is nearly full. How do I move  iTunes music, etc folders to a different location on an external hard drive and still access as if on my Mac?

    My Mac Book  hard drive is nearly full. How do I move  iTunes music, etc folders to a different location on an external hard drive and still access as if on my Mac?

    http://support.apple.com/kb/HT1449

Maybe you are looking for