AP541N cluster and VLAN

Hi.
Simple but not obvious question.
I've added separated wifi for guest with VLAN ID 300. Now I have 2 more access points. They are in cluster but only one is connected to smart switch SLM2008.
Should I need to connect all of them to smart switch? I do not understand how cluster and VLAN work.

Hello Tomasz,
Yes. I guess you need to connect all APs to the switch (same bridged network). Clustering only makes all your AP act as one single entity ( you don't have to connect to the second AP In a cluster separately. Same wireless configuration will do).
Refer Clustering section under the below manual for further details:
http://www.cisco.com/en/US/docs/wireless/access_point/csbap/AP541N/administration/guide/AP541Nadmin.pdf#page139
Hope this helps,
Vijay
Please rate useful posts.
Sent from Cisco Technical Support iPad App

Similar Messages

When setting up converged network in VMM cluster and live migration virtual nics not working

Hello Everyone,
I am having issues setting up converged network in VMM. I have been working with MS engineers to no avail. I am very surprised with the expertise of the MS engineers. They had no idea what a converged network even was. I had way more
experience then these guys and they said there was no escalation track so I am posting here in hopes of getting some assistance.
Everyone including our consultants says my setup is correct.
What I want to do:
I have servers with 5 nics and want to use 3 of the nics for a team and then configure cluster, live migration and host management as virtual network adapters. I have created all my logical networks, port profile with the uplink defined as team and
networks selected. Created logical switch and associated portprofle. When I deploy logical switch and create virtual network adapters the logical switch works for VMs and my management nic works as well. Problem is that the cluster and live
migration virtual nics do not work. The correct Vlans get pulled in for the corresponding networks and If I run get-vmnetworkadaptervlan it shows cluster and live migration in vlans 14 and 15 which is correct. However nics do not work at all.
I finally decided to do this via the host in powershell and everything works fine which means this is definitely an issue with VMM. I then imported host into VMM again but now I cannot use any of the objects I created and VMM and have to use standard
switch.
I am really losing faith in VMM fast.
Hosts are 2012 R2 and VMM is 2012 R2 all fresh builds with latest drivers
Thanks

Have you checked our whitepaper http://gallery.technet.microsoft.com/Hybrid-Cloud-with-NVGRE-aa6e1e9a for how to configure this through VMM?
Are you using static IP address assignment for those vNICs?
Are you sure your are teaming the correct physical adapters where the VLANs are trunked through the connected ports?
Note; if you create the teaming configuration outside of VMM, and then import the hosts to VMM, then VMM will not recognize the configuration.
The details should be all in this whitepaper.
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com )

Logical network to physical network mapping (subnets and VLANS) in SCVMM 2012 R2

In much of the blogs, documentation and literature on VMM, there are examples of deploying multiple logical networks onto one physical network i.e. Cluster (logical) + Storage (logical) + Backup (logical) + Live Migration (logical) + Management
(logical) on top of Datacenter (physical).
Does this mean it would be possible to have one (physical) flat VLAN-less network with one subnet and then have all those logical networks (with subnets and VLANs) on top of it? Even with a simple unmanaged L2 switch that doesn't support VLANs itself?
If not, just how do you map multiple logical networks to just one physical network? How does that work in practice? Is a L3 switch needed to route traffic between logical networks for example?

Hi. VMM Networking may be overwhelmed for the most, at first. But you really need to understand the modeling here and how things are related to each other. Especially if using NIC teaming in WS 2012 (and R2) together with this mix.
I suggest that you read the following whitepaper where we explain how to setup networking in VMM (also to support network virtualization, but that is absolutely not mandatory): http://gallery.technet.microsoft.com/Hybrid-Cloud-with-NVGRE-aa6e1e9a
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com )

Some error in cluster alertlog but the cluster and database is normal used.

hi.everybody
i used RAC+ASM,RAC have two nodes and ASM have 3 group(+DATA,+CRS,+FRA),database is 11gR2,ASM used ASMlib,not raw.
When i start cluster or auto start after reboot the OS,in the cluster alertlog have some error as follow:
ERROR: failed to establish dependency between database rac and diskgroup resource ora.DATA.dg
[ohasd(7964)]CRS-2302:Cannot get GPnP profile. Error CLSGPNP_NO_DAEMON (GPNPD daemon is not running).
I do not know what cause these error but the cluster and database can start normal and use normal.
I do not know whether these errors will affect the service.
thanks everybody！

anyon has the same question?

How do I add a Subnet and vlan with a catalyst 3550 and RV120

Hello Friends.
I have a scenario that i'm hoping i can get some help with. I'll be as detailed and descriptive as i can.
This is for a business with 100 employees nodes and 100 camera nodes all needing IP internet through private addressing and public gateway.
I have a business class gateway with a private range of 12 public addresses. Ther modem does nothing but act as a gateway since i have disabled the firewall and DHCP.
In place of the firewall and DCHP from the modem i have installed a RV120 Firewall with VPN. When installing i replicated the IP scheme of the modem as to not disturb and distrup the devices assigned addresses from that scheme from the modem. I did this because the owner could not have any down time or any disruption to the business operations.
The RV120 now acts as firewall , DHCP , and VPN. I'll address the subnet first. I's using 10.0.0.0/24 subnet range.
DHCP is assigning 10.1.10.50 - 10.1.10.100 the rest are static and i plan to use static DHCP with the IP and MAC assigned to each static DHCP address.
There are 100 cameras with static IP addresses in the range of 10.1.10.11 - 10.1.10.40, and 10.1.0.1.101 - 10.1.10.170.
VPN uses PPTP assigned address 10.1.10.6 - 10.1.10.10.
There are no layer 3 switches that i know of. Just a layer two that is the primary swith and ports have run out, and various out of the box switches and wireless access points connected to the primary switch.
I want to implement subnets into the network and VLANS as well on a new Layer 3 switche from cisco. Thinking 3550 from Cisco or one of the older layer 2 switches with layer three capabilities.
I also want to introduce a 192.168.0.0/24 IP range for the existing wireless network and segment the traffic from the rest of the traffic on other ranges.
I want to replace the 10.0.0.0/24 DHCP alltogether and the static addresses for end user nodes on the same network, but keep that range just for camera nodes segmented.
I want to implement a NEW end user IP range and VLAN for employee/guest networks using the 172.16.0.0/24 range.
Iv'e thought of replacing all the wireless nodes with RV120's and use VLAN. Dont know if that strategy works. Need to think it through.
I want the 192.168.0.0/24 IP range comunicate to with the 172.16.0.0/24 and possibly the 10.0.0.0/24 range.
Any advice on how to do this?
As a side note the next step after this is to install a server domain controller as all the computers are all stand alones in their own workgroups. It's a simultaneous project that will introdue a DCHP, WINS, DNS server.

Hi Omid, it sounds like you're proposing the 3550 switch but you're not decided yet. The 3550 switch is a pretty old device and needs enhanced multilayer image. It may be more prudent to use a more current switch such as small business SG300 or SG500 as the feature set is more rich and it supports around 480 LAN connections.
To answer the inquiry, the RV120W, when you create a VLAN it will automatically create an IP interface. From this you may assign subnet as you like along with 'enable or disable' for inter vlan routing. Since the RV120W has this feature, a layer 3 switch is not required unless you are looking to keep the routing load smaller by routing locally with the switch.
With Catalyst or a small business switch you would need to create a VLAN. After creating the VLAN, on a Catalyst you can simply issue "switchport trunk encapsulation dot1q" on the desired interface and all VLAN will passage without issue. For a port connecting a user "switchport mode access" "native vlan xx" This will assign the port as untag member of the desired VLAN.
If using a small business switch, it is slightly different, you still create the VLAN but the command issue is a bit different "switchport trunk allowed vlan add xx" for the link to the router, where xx = the VLAN ID to tag to the router. For access client it remains the same as Catalyst.

After bring the Cluster and ASM is up, I'm not able to start the rdbms ins.

I am not able to bring the database up.
Cluster and ASM is up and running.
ORA-01078: failure in processing system parameters
LRM-00109: could not open parameter file '/oracle/app/oracle/product/11.1.0/db_1/dbs/initTMISC11G.ora'

That is wre the confusion is: I coud nt find it under O_H/dbs,
However the log file indicates that it is using spfile which is located at :
spfile = +DATA_TIER/dintw10g/parameterfile/spfile_dintw10g.ora
Now it checks only the /dbs directory only i guess.
Could you please how can i bring it up now.
Just for the information: ASM instance is up.

Using ASM in a cluster, and new snapshot feature

Hi,
I'm currently studying ASM and trying to find some answers.
From what I understand and experienced so far, ASM can only be used as a local storage solution. In other words it cannot be used by network access. Is this correct?
How is the RDBMS database connecting to the ASM instance? Which process or what type of connection is it using? It's apparently not using listener, although the instance name is part of the database file path. How does this work please?
How does ASM work in a cluster environment? How does each node in a cluster connect to it?
As of 11g release 2, ASM provides a snapshot feature. I assume this can be used for the purpose of backup, but then each database should use it's own diskgroup, and I will still need to use alter database begin backup, correct?
Thanks!

Markus Waldorf wrote:
Hi,
I'm currently studying ASM and trying to find some answers.
From what I understand and experienced so far, ASM can only be used as a local storage solution. In other words it cannot be used by network access. Is this correct?Well, you are missing one point that it would entirely depend on the architecture that you are going to use. If you are going to use ASM for a single node, it would be available right there. If installed for a RAC system, ASM instance would be running on each node of the cluster and would be managing the storage which would be lying on the shared storage. The process ASMB would be responsible to exchange messages, take response and push the information back to the RDBMS instance.
How is the RDBMS database connecting to the ASM instance? Which process or what type of connection is it using? It's apparently not using listener, although the instance name is part of the database file path. How does this work please?Listener is not need Markus as its required to create the server processes which is NOT the job of the ASM instance. ASM instance would be connecting the client database with itself immediately when the first request would come from that database to do any operation over the disk group. As I mentioned above, ASMB would be working afterwards to carry forward the request/response tasks.
How does ASM work in a cluster environment? How does each node in a cluster connect to it? Each node would be having its own ASM instance running locally to it. In the case of RAC, ASM sid would be +ASMn where n would be 1, 2,... , going forward to the number of nodes being a part of teh cluster.
As of 11g release 2, ASM provides a snapshot feature. I assume this can be used for the purpose of backup, but then each database should use it's own diskgroup, and I will still need to use alter database begin backup, correct?You are probably talking about the ACFS Snapshot feature of 11.2 ASM. This is not to take the backup of the disk group but its like a o/s level backup of the mount point which is created over the ASM's ACFS mount point. Oracle has given this feature so that you can take the backup of your oracle home running on the ACFS mount point and in the case of any o/s level failure like someone has deleted certain folder from that mountpoint, you can get it back through the ACFS snapshot taken. For the disk group, the only backup available is metadata backup(and restore) but that also does NOT get the data of the database back for you. For the database level backup, you would stillneed to use RMAN only.
HTH
Aman....

Question about the Cluster and Column width in Graphs in Illustrator CS2

How do they relate to each other? How do the Percentages work together? Is there any information about how you can mathematically figure how much area each Cluster width takes. If you make a graph and make both the cluster and column widths 100%, the entire area is filled. If you make the Column width 50% the bar will sit exactly in the center of the Cluster width, but if you make the cluster width 75%, the bars move closer together.

Gregg,
The set of bars that represent each row of data in the graph spreadsheet is called a "cluster".
Let's let
   W = the width of the whole area inside the graph axes
   R = the number of rows of data
   C = the number of columns of data
Then the maximum potential space to use for each row of data is W/R. The cluster width controls how much of this potential space is assigned to each row. This cluster space is then divided by C, giving the maximum potential width of each bar. The maximum potential width for each bar is then multiplied by the column width percentage to get the actual width of each bar.
So the actual width of each bar is ((W/R)*Cluster width)/C)*Column width
The graphs illustrated below have three rows of data, with two columns each. The solid colored areas in the background have the same cluster width as the main graph, but they all have a column width of 100%. This lets you see more easily how the gradient bars that have a column width of 80% are using up 80% of their potential width.
Notice that as the Cluster percentage gets lower, the group of bars that represent a row of data get farther apart, so that you can more easily see the "clumping" of rows. When the Cluster percentage is 100%, the columns within each row are no closer to each other than they are to the columns in other rows.
As the Column percentage gets lower, the bars for each data value occupy less of the space within their row's cluster, so that spaces appear between every bar, even in the same row.

ECC 6.0 installation on HPUX Cluster and oracle database

Hi,
I need to install ECC6.0 installation on HPUX Cluster and oracle database. Can anybody plz suggest me or send any document to me ..
Thanks,
venkat.

Hi Venkat,
Please download installation guide from below link:-
https://websmp105.sap-ag.de/instguides
Regards,
Anil

Solaris 8 patches added to Solaris 9 patch cluster and vice versa

Has anyone noticed this? On the Solaris 8 and 9 patch cluster readmes, it shows sol 9 patches have been added to the sol 8 cluster and sol 8 patches have been added to the sol 9 cluster. what's the deal? I haven't found any information about whether or not this is a mistake.

Desiree,
Solaris 9's kernel patch 112233-12 was the last revision for that particular patch number. The individual zipfile became so large that it was subsequently supplanted by 117191-xx and that has also been supplanted when its zipfile became very large, by 118558-xx.
Consequently you will never see any newer version than 112233-12 on that particular patch.
What does <b>uname -a</b> show you for that system?
Solaris 8 SPARC was similarly effected, for 108528, 117000 and 117350 kernel patches.
If you have login privileges to Sunsolve, find <font color="teal">Infodoc 76028</font>.

Cluster and Backup server

Hello guys;
I want to use a cluster oracle server and another server in another place as a backup server to copy the database on line from the cluster server.
If I want to make the backup server a primary server if something wrong happened to the cluster server.
what the steps should I do? or if there is any document to read I'll be thankful
thanks in advance

Hi,
What do you refer by saying cluster ? If you want to have a HA (High Availability) with Active/Passive cluster then you can go with 3rd party cluster vendor, like HACMP from IBM, ServiceGuard from HP and so on. If you want to create this with Oracle technologies then you are talking about Oracle RAC One Node. Of course you always go with Oracle RAC (Real Application Cluster) if you want to have a Active/Active cluster. These are in terms of cluster and High Availability.
There is another point if you want to create a DR (Disaster Recovery) of you primary database then you would consider implementing Oracle Dataguard.
Oracle has a rich documentation for blueprints and best practices, my sincerely advice is to get familiar with it:
http://www.oracle.com/technetwork/database/features/availability/maa-090890.html
Regards,
Sve

Cluster and space consumption

I'm confused about some thing in regards to clusters. I have about 1GB wort of data when it is not in a cluster, just in a normal table. If I create a cluster and insert the data in to this cluster it consumes more space, and that was fully expected. When I tried the first few times it took 13GB of space. The table space was 30GB large and contained a few other tables. Then I cleaned out the table space so only 2% of the space was used and added another 30GB to the table space and ran the test once more. Now it is consuming more than 40GB and is still not completed. So my question is does the size the cluster consume depend on the size and available space of the tablespace it is in? Is there a way to limit the size it is allowed to use other than to put it in a separate tablespace?

Hi Marius,
First, by "cluster" you mean sorted cluster tables, right?
http://www.dba-oracle.com/t_sorted_hash_clusters.htm
So my question is does the size the cluster consume depend on the size and available space of the tablespace it is in?These are "hash" clusters, and you govern the range of hash cluster keys, and hence, the range where Oracle will store the rows.
http://www.stanford.edu/dept/itss/docs/oracle/10g/server.101/b10739/hash.htm
Oracle Database uses a hash function to generate a distribution of numeric values, called hash values, that are based on specific cluster key values. The key of a hash cluster, like the key of an index cluster, can be a single column or composite key (multiple column key). To find or store a row in a hash cluster, the database applies the hash function to the cluster key value of the row. The resulting hash value corresponds to a data block in the cluster, which the database then reads or writes on behalf of the issued statement.

Cluster and Read Write XML

In my applications I allow users to save their settings. I used to do this in a Ini file. So I wrote a Vi that could write any cluster and it worked ok. When I discovered that in the newer versions of LabVIEW you could Read/Write From/To xml, I changed inmediatly because it have some advantages form me but I am having some trouble.
Every time I want to save a cluster I have to use
Flatten To XML -> Escape XML -> Write XML
and to load
Load From XML -> Unescape XML -> Unflatten from XML.
I also do other important things each time I save or load settings. So it seems to be reasonable to put all this in just two subvi's. (One for loading, One for saving). The problem is that I want to use it with any cluster
What I want with can be summarized as following:
- SaveSettings.vi
--Inputs:
---Filename
---AnyCluster
---Error In
--Outputs
---Error Out
-LoadSettings.vi
Inputs:
---Filename
---AnyCluster
---Error In
Outputs
---DataFromXML
---Error Out
I have tried using variants or references and I was not able to make generic sub vi (sub vi that don't know what is in the cluster). I don't want to use a polymorphic vi because it will demand making one load/save pair per each type of settings.
Thanks,
Hernan

If I am correct you still you need to wire the data type to the Variant To Data. How can you put in a subvi ALL that is needed to handle the read/write of the cluster? I don't want to put any Flatten To XML or Unflatten From XML outside.
The solution I came out with INI files was passing a reference to a cluster control but it is real unconfortable because I have to itereate through all items.
When a control has a "Anything" input, is there any way to wire that input to a control and remains "Anything"?
Thanks
Hernan

Cluster and transparent table

Hi
Can some one explain me what is meant by cluster and transparent table
Points will be rewarded.
Regards
Raghu Ram.

hi Raghu,
just make a search about this in the ABAP Forum, there are tons of threads about the topic, here is just the most recent example:
transparent vs pooled vs cluster tables
hope this helps
ec

Cluster and CSS

I have successfully set up two servers in a cluster and
started to test out an application. One issue I am having is that
the CSS that is being imported into the page via @import
url("screen.css") is not being found. If I do a cfinclude then it
seems the styles seem to be somewhat working. Does anyone have any
ideas why this is?
Also I have images on the page with the same problem. I see
the alt No instead of the actual image.
<input type="image" alt="No" src="../images/N.gif"
name="editStuSec" value="1 />

We use an Apache web server which is different from our CF
server. And I have tried putting the images in the web root of the
CF server and also creating a mapping to the images. The images
work fine if I don't go through the cluster.

AP541N cluster and VLAN

Similar Messages

Maybe you are looking for