AP541N-E-K9 2.4Ghz and 5 Ghz at same time

Hello Everyone,
I'd like to set up a 2.4Ghz and a 5Ghz SSID at the same time, using one Cisco AP541N-E-K9. But I can't figure out any way to do so. Is there a possible way?
Kind Regards

Hello Christoph,
The device only has one wireless radio. Its only possible to either have 2.4ghz or 5ghz being broadcast but not both at the same time.
Thanks,
Clayton Sill

Similar Messages

IP over Firewire and ethernet at the same time?

Is it possible to use both IP over Firewire and ethernet at the same time?
I want to use my TB hard drive attached to one Mac via Firewire 800 to backup another Mac also attached to the same drive via Firewire 800. I can only mount the drive on one machine at a time so I need to share it out to the other Mac. It works great if I set it up to do strait IP over Firewire, with static IPs, but that means I can't connect to the internet because my ethernet connection on both machines becomes the secondary connection method. Similarly, if ethernet is primary then I can't connect via Firewire. Is there a way to set it up so the Macs will know which method to use depending on the IP address?
I am using 10.5.1 on both machines.
G5, 1.8 GHz, 15.GB RAM
MBP, 2.4 GHz, 4GB RAM
Thanks!

Certainly.
In the network control panel I set Built-in FireWire to the top of the service order list, followed by Built-in Ethernet.
Next, I set Built-in FireWire to Configure Manually with the address 192.168.1.xxx and the Subnet Mask to 255.255.255.xxx, making sure the Subnet Mask is set the same on both machines and that the IP address is different on both machines and different from the Built-in Ethernet addresses.
I applied the settings, turned on Sharing on both machines, then mounted whatever shared drives I needed by connecting to the other machine using the FireWire IP address.
Now I am able to share drives using FireWire 800 - which works great when used with Time Machine - and still use my normal ethernet to surf, etc..

Why can't I run Safari and Skype at the same time without making my computer freeze up?

I can't believe I can't run Safari and Skype at the same time without my computer freezing up, it's a MacBook Pro with Mac OS 10.6.8 and it has an Intel Core 2 Duo CPU with 2.2 Ghz and 2 Gb of RAM. Is this a hardware problem or a software problem?

I haven't gone to the trouble of actually testing to see which uses more CPU power, but Firefox has been faster than Safari on every Mac I've ever owned.
To see CPU usage by process, open the terminal (in Utilities) and enter 'top' at the command line. You might have to expand the window as processes don't appear in any logical order.
It could also be hardware-related: I have late 2009 mini with similar specs and it pinwheels easily.

My Ipad mini does not see my printer. my wife's ipad2 does. We both use IOS8 and upgraded at the same time. How can I remedy this?

My Ipad mini does not see my printer. my wife's ipad2 does. We both use IOS8 and upgraded at the same time. How can I remedy this?

OK great info!
I found 2 possible ethernet to USB adapters:
By "Plugable": USB 2.0 to ethernet LAN wired network adapter - seems this will work, but I'll contact Plugable.
2. Apple USB Ethernet Adapter
Easily connect your MacBook Air computer to an Ethernet network with the Apple USB Ethernet Adapter. Small and light, it connects to the USB 2.0 port of your MacBook Air and provides an RJ-45 connector that supports 10/100BASE-T performance. BUT NOT SURE IF THIS WILL WORK ON ANYTHING BUT a MacBook Air…
One person commented:
This little gem used to be the device of choice for adding a second Ethernet interface to a Mac Mini Server and I'd been using one that way for about a year. After doing a software update to 10.6.6 it stopped working. Forewarned is forearmed – it appears that Apple is finally enforcing the MacBook Air system requirement.
Thanks for any additional comments.
Best regards,
Steve Schulte
Sunday 6 January 2013

How do i start video and audio at the same time in ios

How do i start video and audio at the same time in ios?
I have tried a lot of different ways but i cant figure it out?
I can get the sound and animation (timeline) to start playing.
There is no problem to start the video and the animation at the same time.
But i cant get both the video and the audio to start playing when i press a button.
It works great in OSX and on windows?
Here is an example:
// insert code for mouse click here
// Play an audio track
sym.$("_1")[0].play();
// Play a video track
sym.$("host")[0].play();
// Play the timeline at a label or specific time. For example:
// sym.play(500); or sym.play("myLabel");
sym.play("marker1");

If the game has sound in it (and possibly even if it doesn't) it may be overriding the Music app and causing it to stop playing - in which case there is nothing that you can do about it.

Recording Audio and Midi at the same time in Logic 7 Express Can it be done

I am wondering if I can record audio and midi at the same time in Logic 7 Express. I am running my guitar thrugh a Roland GR 33, and a line out and using the GR 33 to trigger sounds in the Logic's synth section but cant seem to record all three tracks at once. If any one knows how let me know. Oh and I am running the GR Synth and Guitar into the Prosonus Fire Fox and have the GR 33 out midi to the Fire Box as well. So I guss the question is how do I sent up two audo tracks and one midi track to record in real time. Thanks Victor

I am wondering if I can record audio and midi at the
same time in Logic 7 Express. I am running my guitar
thrugh a Roland GR 33, and a line out and using the
GR 33 to trigger sounds in the Logic's synth section
but cant seem to record all three tracks at once. If
any one knows how let me know. Oh and I am running
the GR Synth and Guitar into the Prosonus Fire Fox
and have the GR 33 out midi to the Fire Box as well.
So I guss the question is how do I sent up two audo
tracks and one midi track to record in real time.
Thanks Victor
Try arming the audio tracks, select one of the tracks, then while holding down the shift key, select the midi track you want to record, arming the "r" on the midi track. Press "record".....
HL

Can we use both INSERT and UPDATE at the same time in JDBC Receiver

Hi All,
I would like to know is it possible to use both INSERT and UPDATE at the same time in one interface because I have a requirement in which I have to perform both the task.
user send the file which contains both new and old record and I need to save those in MS SQL database.
If the record exist then use UPDATE otherwise use INSERT.
I looked on sdn but didn't find any blog which perform both the things at the same time.
Interface Requirement
FILE -
> PI -
> JDBC(INSERT & UPDATE)
I am thinking to use JDBC Lookup but not sure if it good to use for bulk record.
Can somebody please suggest me something or send me the link of any blog or anything to solve this problem.
Thanks,

Hi ,
          If I have understood properly the scenario properly,you are not performing insert and update together. As you posted
"If the record exist then use UPDATE otherwise use INSERT."
Thus you are performing either an insert or an update which depends on outcome of a search if the records already exist in database or not. Obviously to search the tables you need " select * from ... where ...." query. If your query returns some results you proceed with update since this means there are some old records already in database. If your query returns no rows you proceed with "insert into tablename....." since there are no old records present in database.
Now perhaps the best method to do the searching, taking a decision to insert or update, and finally insert or update operation is to be done by a stored procedure in MS SQL database. A stored procedure is a subroutine available to applications accessing a relational database system. Here the application is PI server.   If you need further help on how to write and call stored procedure in MS SQL you can look into these links
http://www.daniweb.com/web-development/databases/ms-sql/threads/146829
http://www.sqlteam.com/article/stored-procedures-parameters-inserts-and-updates
[ This part you can ignore, Since its not sure that you will face this situation
    Still you might face some problems while your scenario runs. Lets consider this scenario, after the stored procedure searches the database it found no rows. Thus you proceed with an insert operation. If your database table is being accessed by multiple applications (or users) other than yours then it is very well possible that after the search operation completed with a null result, an insert/update operation has been performed by some other application with the same primary key. Now when you are trying to insert another row with same primary key you get an error message like "duplicate entry not possible for same primary key value". Thus you need to be careful in this respect. MS SQL has a feature called "exclusive locks ". Look into these links for more details on the subject
http://msdn.microsoft.com/en-us/library/aa213039(v=sql.80).aspx
http://www.mssqlcity.com/Articles/Adm/SQL70Locks.htm
http://www.faqs.org/docs/ppbook/r27479.htm
http://msdn.microsoft.com/en-US/library/ms187373.aspx
http://msdn.microsoft.com/en-US/library/ms173763.aspx
http://msdn.microsoft.com/en-us/library/e7z8d5hf(v=vs.80).aspx
http://mssqlserver.wordpress.com/2006/11/08/locks-in-sql/
http://www.mollerus.net/tom/blog/2008/03/using_mssqls_nolock_for_faster_queries.html
    There must be other methods to avoid this problem. But the point is you need to be sure that all access to database for insert/update operations are isolated.
regards
Anupam

SSO and User Mapping at same time

Hi,
Can we use SSO and User mapping at same time between Portal and SAP Backend system?
For some of the users the user id is different in both end.
After implementing the SSO... Will it affect the existing user mapping? and the system alias created for that?
If not, Can we use both SSO and user Mapping same time?
Thanks,
VB

Hi VB,
In this case I suggest you create 2 systems one you might have created for users who are having common user ids in portal & at the backend system.
For the users whose ids are defeering you can create reference system and in user managemant property of that system
Authentication Ticket Type - Select -SAP Logon TicketSAP Assertion Ticket
Logon Method - UWPW
User Mapping Fields - {100,200,300}Client;Language
where 100,200,300 are the clients of the backend system.
Assign this system in the ivews.
Thanks,
Vishal

Can I use a camera for application in Labview and VBAI at the same time ?

Dear all,
I'm trying to save an AVI file with Labview and make an image process with VBAI at the same time, in one machine.
The error : "Camera already in use" displayed.
My Camera is a GIGE and I work with Imaqdx. I've test the multicast mode but it only operate with several machines.
How can I do this ?
Thank's to help me,
Yoann B

I'm not necessarily saying that. It's been a while since I've used VBAI, so I don't remember all of the capabilities, but if VBAI can do the inspection and recording at the same time, you should be fine.
The trick is that only one program can access the camera at the same time. That application reserves the camera, thus making it unavailable to others.
Chris
Certified LabVIEW Architect
Certified TestStand Architect

My SB Audigy 2 card can't use headset and musicamplifier at the same time

Hi, i just bought a SB Audigy 2 [D400] and i have downloaded drivers and programs. I run Windows XP SP2.
The soundcard works fine but it is very very annoying that i physically have to change the jack in the green=line out jack from headset to musicamplifier when i want to use my musicamplifier and change back the jack in the green=line out from musicamplifier to headset when i just want to use the headset/headphones .
In the shop they told my that i can connect both amplifier and headset at the same time and then with creative software control whether there is sound in the headset or in the amplifier. But i can't simple get it work.
I tried to use the green to the amplifier and the headset/speakers in the black (line out 2) and then with creative speaker settings softeware choose headphones but still the ampliefier receive the sound and no sound in the headphones. Why? In fact no matter what configuration i try the headphones doesn't work.
But if i change the jacks so headset is in the green line out then only headset is working and the amplifier doesn't work no matter i put it in sort=line out 2 jack or orange=line out 3 jack.
Can somebody here tell me if it is possible or not to connect both headset and external amplifier and control by software which to play? and how?
please help, thx.
Michael

If you can have an ASIO compatible music playing system, then it might be possible to have system like you wish when using Creative Audigy 2 card. Since ASIO bypasses Windows Audio System, you can use both 'drivers' (ASIO - WDM/MME/DS) side by side.
Say you want to play a game (using headset /w mic) and someone other like to listen music at the same time. With ASIO capable system you can output your music for example to "center L/R (stereo) channels" and same time output sounds from other source (using MME/DS/WDM drivers) to normal output channel (Front L/R). Only thing is, you need to set your speakersystem to 4 or 6 (depending which other channel you're using) (and for better 'balance' to adjust "angle" on THX console. You get the THX console by installing Audigy 2 Zs software).
Try for example http://img332.imageshack.us/img332/463/djs9mo.jpg[/img] width="406" alt="Image Hosted by ImageShack.us" >
Another option:
Say you want to play music through external amplifier and play game online with your headset + microphone (eg. others but you listen the music, you play games)
--> try free http://img332.imageshack.us/img332/4589/tbp7rz.jpg[/img] width="406" alt="Image Hosted by ImageShack.us" >
If you use ASIO on BeatPort Player you can select L/R individually from the list(s). Same rules as described earlier.
= You can play from 2 different sources simultaoneusly (ASIO + WDM/MME/DS) to two different outputs without disturbance. The other (WDM/MME/DS) source is set 'automatically' output to (Audigy) "green" port, and the other (ASIO) to "black" or "orange" port (as set).
.jtpMessage Edited by jutapa on 09-5-2005 05:30 AM

My wifes iphone was too full to record a video so I upgraded her cloud storage to 20g and did mine at same time. Cloud is showing 15g free storage butshe still cannot take any mor photos as "not enough memory" What is the point of paying for the extr

My wifes iphone was too full to record a video so I upgraded her cloud storage to 20g and did mine at same time. Cloud is showing 15g free storage butshe still cannot take any mor photos as "not enough memory" What is the point of paying for the extr

Hello Pushtheriver,
After reviewing your post, I have located an article that can help in this situation. It contains a number of troubleshooting steps and helpful advice concerning iCloud storage issues:
Get help using iCloud storage
This may also help:
Understanding iOS device capacity
You can sync and download many different types of content on your device. Some types of content (such as music and videos) typically take more space than others (such as notes and books). The amount of space taken by an app depends on the app's purpose; complex or graphically intense apps usually take more space than simpler apps.
If your device is near its capacity, you can remove some of the less used content to make room for more.
Thank you for contributing to Apple Support Communities.
Cheers,
BobbyD

Ipod nano (5th generation) - want to use headphones and charge at the same time

I have an ipod nano (5th generation). Do I need a special set of headphones to use the headphone jack and charge the ipod at the same time?

The iPod nanos have a 30 pin dock connector and a headphone jack. When you charge the iPod you use the dock connector therefore you can use and charge at the same time. You cannot use and charge the iPod shuffle at the same time. You might have the two mixed up.

Problem with audio of my notebook. Audio works through pc speakers and earphones at the same time

Hi all,
thanks in advance for your advices.
I have a problem with my notebook (HP pavilion g6 2305 sl).
The problem is that when I connect my earphones the audio of my pc don't stop, hence I can hear (music, film, ...) both by earphones and speakers at the same time.
I tried to install again the latest driver audio, but nothing was changed.
I tried to use another pair of earphones, but nothing.
I have noted that if I connect the Jack at my pc, but not until the end, the audio stops from the speakers and goes through the earphones, but only if the jack is not completly inserted in the notebook.
I read a lot of forum on the web but I'm not able to find a solution for my problem.
(ps. the problem comes out suddenly, without any signal. I don't have installed any update or new software before the problem's start)

Right click on speaker icon, lower right screen.
Choose playback devices.
Select "speakers and headphones" as your default.
Disable "communications headphones".

Error Running Oracle Apps and Discoverer at the same time

Hello,
We are having trouble running Oracle Apps and Discoverer at the same time on certain user's machines. Here are the specifics:
The user opens Oracle Apps in Internet Explorer. The user then opens Discoverer in another Internet Explorer windows and receives the following error: Runtime Error! Program: C:\Program Files\Internet Explorer\iexplore.exe abnormal program termination
As a work around, I installed Firefox on those user's machines. These users run Oracle Apps in Internet Explorer and run Discoverer in FireFox. This has solved the problem in 99% of the cases. However, there is one user who is having FireFox using Discoverer freeze when running Oracle Apps in Internet Explorer.
Can anyone provide any insight on how I can solve these conflict issues so users can run Oracle Apps and Discoverer at the same time?
Thanks in advance for your help,
Carlos

Hi Michael,
I agree with you completely. It is reccommended to run 10g on a separate physical server unless you have sufficient resources to run on the same server (which even most large clients do not) Even then, I would recommend a separate server.
I should have put my comment in context :-)
a.) I was only stating that it was possible
and
b.) whether 10g is installed on the same physical server or separate should not affect the client browser crashing issue that was posted.
I do have an install with EBS11i and Discoverer 10g on the same physical server and it works fine (this is sandbox/ TEST). Most of my large customers have 10g installed on multiple physical servers due to load balancing (capacity).
I do work for Oracle. I try to help out on the forum when I can, but it is hit or miss :-(
I would be glad to discuss anything privately.
As for the issue at hand, I can reproduce the problem and here is what is occuring.
I have EBS 11i configured with Jiniator 1.3.24
I have Discoverer 10g configured with Sun Java plugin 1.4.2_06
1. If you launch EBS 11i apps and a form with MS IE, then the browser launches the form using Jiniator JRE 1.3.xx (whatever you have configured in AutoConfig for EBS11i)
2. Next, the user navigates to EBS 11i SSWA and launches a Discoverer workbook.
What occurs is a child IEXPLORE.exe process is spawned from the parent IEXPLORE.exe process and Discoveer Plus is launched. The parent iexplore.exe process will be attached to the Jiniator JVM. Now if Discoverer is configured with
a.) Sun Java Plugin or
b.)a version of Jinitiator that is a different version from what EBS 11i is configured with
then you may get this conflict.
It really is an MS IE/JRE conflict with Jinitiator and Sun Java Plugi and the way the broswers attaches to the JVM (IMHO) as this behaviour could be reproduced with other non-oracle java applets.
You can workaround the situation by:
a. configure EBS11i and Discoverer to use the same version of Jiniator 1.3.xx
b. educate the users to open one MS IE browser to connect to EBS11i and then open a second MS IE browser to login to EBS11i SSWA or Discoverer 10g Plus directly to launch workbooks. They need to to this by clicking on the icon and not using File >> New browser. Clicking on the icon will spawn a new parent iexplore.exe process that can attach to a second/different JVM. File >> New Window will spawan a child of the parent.
c. As you did use two browser versions. MS IE for EBS11 connection and FireFox for Disocverer 10g connection.
I would choose optoin b, so that you can use Sun Java Plugin with Discoverer.
Open to any comments. I hope that helps you workaround the problem. The ideal solution is to have EBS 11i use/cerified with the 1.4 or 1.5 JRE. In poking around, I see there is a related post to this on one of Oracle's EBS 11i Product Managers Blog.
See:
http://blogs.oracle.com/schan/2006/04/18#a23

Can I surf and talk at the same time on a verizon iphone?

I've heard that Verizon iPhones don't allow users to talk and surf at the same time. Is that true? I'm not keen on going to AT&T. If it's true, will it ever change?

Yes. It is true because Verizon runs on CDMA which doesn't allow for surf and talk at the same time. AT&T runs on GSM which allows for surf and talk at the same time.

AP541N-E-K9 2.4Ghz and 5 Ghz at same time

Similar Messages

Maybe you are looking for