AP802-BOOT-M bootloader mode and trying to get a new image on there

Ok. Dont ask me how I managed to get myself in this state. Surfice to say I was trying to upgrade an IOS image on an integrated 887 wireless router and its AP802GN access point.
The IOS to LWAP conversion did not go well and now I am in the state where I am trying to get the autonomous image back on there.
so I am faced with either this output.
*Nov 19 22:14:54.423: %SM_LICENSE-6-BOOTIMAGE_CHANGE_TO_AUTO: Boot image has been changed to autonomous image
Please use router EXEC CLI service-module wlan-ap 0 reload
to bootup autonomous image on AP
Which when executed only brings me back again to the same output.
I cannot do a show flash:
it return
So I thought maybe put it in bootloader mode and copy an image across.
So I am at the ap: prompt with no understanding as to what to do next as the AP I think has a 10.0.0.1 address and the router it is sitting in has a 192.168.0.1 address.
I also tried to load a new image when it was in the pr

I hear what your are saying but it would appear that whilst the software 7.0.235.0 which is on my 2106 WLC does support the AP802 the actual hardware of the 2106 does not.
I will raise a TAC case tomorrow with Cisco just to make sure but this excerpt from their website is pretty straight forward.
Cisco 2100 Series Controller
The Cisco 2100 Series Wireless LAN Controllers work with Cisco lightweight access points and the Cisco Wireless Control System (WCS) to provide system-wide wireless LAN functions. Each controller controls up to 6, 12, or 25 lightweight access points for multiple-controller architectures that are typical of enterprise branch deployments. It may also be used for single controller deployments for small and medium-sized environments.
Caution Do not connect a Power-over-Ethernet (PoE) cable to the controller's console port. Doing so may damage the controller.
Note Wait at least 20 seconds before reconnecting an access point to the controller. Otherwise, the controller may fail to detect the device.
Features Not Supported
This hardware feature is not supported on Cisco 2100 Series Controllers:
•Service port (separate out-of-band management 10/100-Mbps Ethernet interface)
•Cisco 2100 Series Controller does not support the access point AP802.

Similar Messages

Why won't my g4 desktop come on. I was trying to boot in safe mode and it would not go in safe mode. It won't come back on anymore. Can some tell me what to do.

Why won't my g4 desktop come on. I was trying to boot in safe mode and it would not go in safe mode. It won't come back on anymore. Can some tell me what to do.

Try Single User mode (Command+S while starting up).
Then, run fsck.
At the command-line prompt type:
/sbin/fsck -fy
Press Return. fsck will go through five "phases" and then return information about your disk's use and fragmentation. Once it finishes, it'll display this message if no issue is found:
** The volume (name_of_volume) appears to be OKIf fsck found issues and has altered, repaired, or fixed anything, it will display this message:
***** FILE SYSTEM WAS MODIFIED *****
Important: If this message appears, repeat the fsck command you typed in step 2 until fsck tells you that your volume appears to be OK (first-pass repairs may uncover additional issues, so this is a normal thing to do).
When fsck reports that your volume is OK, typerebootat the prompt and then press Return.
Your computer should start up normally and allow you to log in.
http://support.apple.com/kb/TS1417

I have had to put my ipod touch in Recovery Mode and tried to sync it with itunes but it wont restore itself. What can I do?

I have had to put my ipod touch in Recovery Mode and tried to sync it with itunes but it wont restore itself. What can I do?

http://support.apple.com/kb/TS3694#error3194
Basic troubleshooting steps
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101
 In Memory of Steve Jobs 

MacBook Pro 13" Only boots to safe mode and running VERY slow.

Hi...
Not posted on here before, but am desperate so hoping there are some experts out there who can help...
I have 13" Macbook pro which has ceased to work properly - it runs very slowly and will only boot in safe mode.
I have installed a new hard disk, but I get the same problem whether I (try to) boot from the old HHD or the new one.
The new drive was imaged using Carbon Copy Cloner.
I have run the repair disk priorities in disk utility and verifying the disk says all OK.
I have set the startup disk to be the new hard disk, and cleared the NVRAM via cmd-option-p-r...
As things stand at the moment, rebooting (not in safe mode) leaves me with the grey screen and apple logo (and no obvious activity for 10+ mins (so far)).
Booting in safe mode takes 3+ mins but I do get to a user login prompt and can get to a desktop.
Any ideas / help very much appreciated as I urgently need to get this machine working!
Thanks!

Domonic White,
when you ran Disk Utility, did you do so from your user account, or from Recovery mode? There are four options there: Verify Disk Permissions, Repair Disk Permissions, Verify Disk, and Repair Disk. Which of these did you do in Disk Utility?
Have you tried resetting your MacBook Pro’s System Management Controller?
Have you tried logging in as your administrative user, opening the Users & Groups pane of System Preferences, creating a new standard user (e.g. “Test”), and trying to log in as the new user, to see if the slow performance affects the new user also?
There is a chance that this could be due to a faulty internal SATA cable. If you have an external disk enclosure, or a SATA-to-USB or SATA-to-FireWire adapter, try booting from one of your drives when it’s externally connected. If it works fine that way, but is sluggish when internal, that could point to your internal SATA cable as the culprit.

My iphone 4s wont turn on with out being pluged in and when i unplug it it dies instantly i pluged it in put it in dfu mode and tried to restore it hoping it might help but its stuck in dfu and has restore error 21 help!!!

my iphone 4s wont turn on with out being pluged in and when i unplug it it dies instantly i pluged it in put it in dfu mode and tried to restore it hoping it might help but its stuck in dfu and has restore error 21 help!!!

Hey jestinsinclairr,
Thanks for using Apple Support Communities.
After reviewing your post, it sounds like you had one issue and then got a second trying to resolve the first. A frustrating situation for sure. The first article linked has what to do if it is not powering on unless plugged in. The second article addresses the error you are receiving when trying to restore.
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Will not turn on, will not turn on unless connected to power, or unexpected power off
Resolve iOS update and restore errors
http://support.apple.com/kb/TS3694#10
Check for hardware issues
Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
Have a nice day,
Mario

I recently wanted to update my phone and so when i put it in recovery mode and tried to set it up it said that i had to enter the apple id that i used to set up the phone the first time but i dont know the information to my old account what do i do?

I recently wanted to update my phone and so when i put it in recovery mode and tried to set it up it said that i had to enter the apple id that i used to set up the phone the first time but i dont know the information to my old account what can i do?

You will need to remember or find the id that you used, without it you won't be able to re-activate your phone - if you are on the activation screen then does that show the first letter of the id and the email provider's name ?
Do you know if you have any of the account's downloads in computer's iTunes library - if you do then you can get the id form that : Recovering a forgotten iTunes Store account name.
If not then see if you can find it via http://appleid.apple.com : Apple ID: How to find your Apple ID.

HT4113 Trying to get my new iPad up and running so many times it is now disabled...help

I have been trying to get my new iPad air up and running . Now it says disabled. What do I do now?

Try recovery mode. See:
http://support.apple.com/kb/ht1808

I have I phone 5 and I can't open iCloud after deleting me old one and tried to open a new one it didn't let me because it said it maxed out

I have my phone is I phone5 and I had an account iCloud but I deleted along time ago and I have no idea what was my email address or user name or password , and tried to open a new one on my phone it won't let me because it said it maxed out and u can open iCloud one time, I need to open a new account so I can safe my information,

I've never seen an error discribing "maxed out". Please type in the exact error message you are seeing so I can maybe assist you further.

My screen on my phone is in a disabled mode and i cant get into my phone. i need to find out how i wipe my phone clean and start over

my phone is in a diabled mode and it cant get into my phone anymore. i need to clear my phone off threw itunes but cant seem to figure it out

http://support.apple.com/kb/HT1212?viewlocale=en_US&locale=en_US

I am using an I phone 5 in Germany and trying to get text messaging to work through the hands free Bluetooth connection on a Honda CRV. It keeps telling me that text messaging is not a feature of my phone. messages come in on the phone.How to resolve ?

I am using an I phone 5 in Germany and trying to get text messaging to work through the hands free Bluetooth connection on a Honda CRV. It keeps telling me that text messaging is not a feature of my phone. messages come in on the phone.How to resolve ?

mono 8 bit 8k is 64kbps, yes. 8 bits times 8,000 = 64,000 = 64k bits/sec.
And yes I think that's a typo - there's no such thing as 'Mone' that I've ever heard of...
But you might want to check to find out if this is a mu-law non-linear format, possibly - there are several ways that 8 bit 8k wav files can be encoded, and typically phone systems don't use linear ones. If you have a log-in to Zultys' user-base system they have an FAQ there, I believe - the answer might be in that, and it won't cost $500.

I just had major issues with my Mac and had to get a new logic board. When I got the computer back and tried to reinstall Photoshop- it says error 6. What do I do?

I just had major issues with my Mac and had to get a new logic board. When I got the computer back and tried to reinstall Photoshop- it says error 6. What do I do? It is impossible to get any phone number for adobe.

Try these solutions: Error "Licensing has stopped working" | Mac OS

Trying to get my New iPad to mirror certain apps to my apple tv. Apps such as showtime anytime and hbo won't mirror on apple tv. Any recommendations?

Trying to get my New iPad to mirror certain apps to my apple tv. Apps such as showtime anytime and hbo won't mirror on apple tv. Any recommendations?

I purchased both the apple tv and VGA connections for my iPad so I can mirror/project this image onto my television. When I purchased both of these items from the store, I was told it would support this feature. Is there anything in development to allow me to mirror the image or connect it via the VGA connector to my television?

I'm trying to download Premier pro and I'm getting an error message saying "There is no application set to open the url aam://SAPCode=PPRO?

I'm trying to download Premier pro and I'm getting an error message saying "There is no application set to open the url aam://SAPCode=PPRO? Does anyone know how to resolve this issue?

RiiichéC please try the process again in a different web browser or install through the Creative Cloud Desktop application. You can find details on how to install the Adobe applications included with your membership at Install and update apps - https://helpx.adobe.com/creative-cloud/help/install-apps.html.

I have changed my PC, deactivated Adobe Acrobat and tried to load on new PC. Got to registration and get the message " A problem was encountered while trying to send information over internet" this is 8 standard

I have changed my PC, deactivated Adobe Acrobat and tried to load on new PC. Got to registration and get the message " A problem was encountered while trying to send information over internet" this is 8 standard
When I try to use it to make pdf files I get the message "Missing PDFMaker files
It is a proper copy with serial numbers

Moving this discussion to the Acrobat Installation & Update Issues forum.

I've preordered my iPhone 5 from apple and tried to get a sim from o2, they said I couldn't preorder. Does anyone have any information about this?

I've preordered my iPhone 5 from apple and tried to get a sim from o2, they said I couldn't preorder. Does anyone have any information about this?

Ethmoid,
Generally buying on contract or buying outright from apple with a separate sim from a provider is little difference in cost.
Work out the total cost over 24 months for the phone+monthly tarrif and you will see.
Also the contracts where the phone is cheapest but have a higher monthly cost tend to be the ones that cost you move over a 24 month period.
For example;
Using O2 UK as an example (other carriers are very similar). For the iPhone 5 64GB;
From Apple £699, plus O2 On & On £20 per month is £1179
From O2, Phone £249, per month, £41. Total over 24 months is £1,233
From O2, Phone £169, per month, £46. Total over 24 months is £1,273
From O2, Phone £69.99, per month, £63. Total over 24 months is £1,581 <Cheapest phone, most expensive
*These all use the same tarrif of unlimited talk,texts and 1GB data. The only difference is how much you want to pay upfront for the phone*
Also worth noting is buying the phone from apple and the O2 tarrif is only a 12 month tarrif so you're not locked in for 24 months.
As you can see, the cheaper the phone, the more the overall amount you pay.

AP802-BOOT-M bootloader mode and trying to get a new image on there

Similar Messages

Maybe you are looking for