Aperture 2 - Launch/Quit takes too long

Hi there,
Need help! I just installed the Aperture 2.1.3 in my new Mac Pro. I have all my pictures in a Drobo 4T connected through my network using DroboShare (ethernet). The reason I bought Aperture is because I can have my library in an external drive (centralized) and because of the organizing options. I have setup Aperture to use pictures library location in Drobo.
*My problem:*
*1) Why every time a Launch/Quit Aperture it takes more than 20min?*
*2) Why all pictures are pixelated? Even though they are all in high resolution. (Taken with Nikon D60)*
Note: Under my old PC I could handle it under the same circumstances but with Picassa. I don't want to come back...
Thanks in advance and hope to find a solution

You can't have the library on the network drive, it's going to be VERY slow. You should have the library on a locally attached drive (preferably internal) and use referenced masters if you want to go that route.
Loading the library over a NAS is too slow for practical use. Especially DroboShare, which is very slow for a NAS device. Locally attached drive is at least 10x faster.

Similar Messages

When using NI ELVISmx Instrument Launcher it takes too long to open myDAQ

myDAQ hardware when connected USB is successfully installed on all 15 computers in a classroom environment and seen in Device Manager. When the application 'NI ELVISmx for myDAQ' is opened, the Instrument Launcher displays successfully on the desktop. The problem is however, when one of the buttons are selected ie: DMM or SCOPE, it takes 2 to 3 minutes to open (it is a white blank until it appears), or it will eventually say 'not responding' or it opens immediately with 'Launcher has stopped working'. This occurs on all the computers in the classroom.
Attachments:
DMM blank display.docx ‏339 KB

Hello meoow2u,
Has the performance of the other software on these machines been affected since ELVISmx was installed, or is the Instrument Launcher the only program exhibiting this behavior?
Regards,
Siana A.
Application Engineering
National Instruments

11gR2:crsctl, srvctl commands takes too long to respond

Hi,
I have successfully configured *11gR2 two node RAC on ASM on Win 2008 64bit.*
Everything work very well like connecting to database, querying database. Node restart also takes acceptable time to go down & restart the clusterware & database.
But when I execute crsctl status resource -t or srvctl status database -d db_name commands from any node takes 10-15min to give output.
They give output & everything completes successfully but takes too long to respond.
The questions are:
- If everything works fine then why crsctl, srvctl takes too long to respond?
- what could be blocking these command to gather clusterware and database status on all nodes?
- what additional info would be helpful that I can provide?

dag wrote:
I dont have this issue either. are you auto starting mpd?
that time is how long it is up in other words you opened it then closed it at that time
I'm not sure if you are referring to me or not, but in my screenshot I am timing the lag in ncmpcpp by pressing 'q' in the terminal during the delay, so it quits ncmpcpp immediately after the lag. The lag is longer for ncmpc because the interface loads before the program connects to mpd, so I have to stop it manually immediatly after it connects.
WonderWoofy wrote:I don't have this problem... if you are starting it as a systemd user service, maybe there is relevant information in the journal.
The journal did not reveal anything relevant sadly. I have now tried launching mpd without systemd, and the lag remains. I have also noticed that a small mpd programming project I am writing also experiences the same lag when it tries to connect to mpd.

RTF export takes too long

Hi all,
you know why a report with a lot of data and many pages (about 300 pages), if I export this in PDF format using short time (1 min) and if I export this in PDF format takes too long (even 10 minutes) and sometimes even times out.
Have an idea?
Thanks

re: Paul. Not true, or shouldn't be. XDCAM HD timeline, XDCAM HD output.
re: Michael. Well, close. I mixdown the edited timeline, then place that into another sequence where I apply a Broadcast Safe filter and hit it with a bit of audio compression. I render that, ridding myself of the dreaded "red lines". However, when I splat-E, I get red lines all over again while I'm exporting. When the export is done, the red lines disappear. Now as an aside, I do experience actual "missing" render files, but that occurs when I quit a project and then re-open it later...they sometimes don't seem to re-link. As I mentioned in this post, I have a feeling that's because this system is set up in the worst way possible (a single RAID5 which acts as system drive and media storage).
Don't blame me, I'm just trying to work within the confines of what I'm given. My major concern here is that it seems to be getting worse.

Muse CC startup takes too long (up to 35 seconds)

For some reason, Muse CC takes too long to launch: up to 35 seconds. The splash screen stays up for that long until the program actually starts.
Photoshop CC, with several plug-ins and presets, takes only 3 seconds. My previous Muse versions launched a lot faster.
I'm on Windows 7, 64 bit. Any recommendations on this? Anybody else experiencing this issue?

Please try to clear Muse's preferences/cache as detailed in the following article and see if that helps.
http://forums.adobe.com/message/5086018#5086018
Thanks,
Vinayak

Having lagging problems with YouTube videos, it simply takes so long for the red bar to completely load and the videos frequently pause and take too long to restart playing again.

I have been having lagging problems with YouTube videos for a number of months now. It simply takes so long for the red bar to completely load and the videos frequently pause and take too long to restart playing again. Even with little 2 and 3 minute videos.
I have a fast computer and my webpages load really, really fast. I have FireFox 4 browser and a Vista Home Premium 64-bit OS. So I don't have a slow computer or web browser. But these slow YouTube vids take way too long to load for some reason.
Does anyone have any idea how I can speed up YouTube?

Hi
The forums are customer to customer in the first instance, Only the mods (BT) will ask for personal information through a email link. Would you mind posting your Hub stats & BT speed test results this will help all with diagnosis-
To post the full stats from your router
for home hub - 192.168.1.254
Navigate to ADSL Settings or use the A-Z at the top right
Click on More Details and then post the results.
Run BT speed tester and post the results from http://speedtester.bt.com/
If possible it would be best to connect to the BT master socket this will rule out any telephone/broadband extension wiring also consider the housing of the hub/router as anything electrical can cause problems as these are your responsibility, if these are found to be the case Openreach (engineer) will charge BT Broadband, which will be passed onto you, around £130.00.
Noisy line! When making telephone calls, if so this is not good for your broadband, you can check-
Quite line test dial 17070 option 2 and listen - should hear nothing best done with old type analogue phone digital (dect) will do but may have slight hiss If you hear noise- crackling pops etc, report it as a noisy line on your phone, don’t mention broadband, Bt Faults on 151.
As for your FTTC its available in some areas between 40% & 80% of customers in enabled areas can receive it!
Mortgage Advisor 2000-2008
Green Energy Advisor 2008-2010
Charity Health Care Provider Advisor 2010-
I'm alright Jack....

Sometimes my computer takes too long to connect to new website. I am running a pretty powerful work program at same time, what is the best solution? Upgrading speed from cable network, is it a hard drive issue? do I need to "clean out" the computer?

Many times my computer takes too long to connect to new website. I have wireless internet (time capsule) and I am running a pretty powerful real time financial work program at same time, what is the best solution? Upgrading speed from cable network? is it a hard drive issue? do I only need to "clean out" the computer? Or all of the above...not to computer saavy. It is a Macbook Pro osx 10.6.8 (late 2010).

Almost certainly none of the above! Try each of the following in this order:
Select 'Reset Safari' from the Safari menu.
Close down Safari; move <home>/Library/Caches/com.apple.Safari/Cache.db to the trash; restart Safari.
Change the DNS servers in your network settings to use the OpenDNS servers: 208.67.222.222 and 208.67.220.220
Turn off DNS pre-fetching by entering the following command in Terminal and restarting Safari:
defaults write com.apple.safari WebKitDNSPrefetchingEnabled -boolean false

Accessing BKPF table takes too long

Hi,
Is there another way to have a faster and more optimized sql query that will access the table BKPF? Or other smaller tables that contain the same data?
I'm using this:
   select bukrs gjahr belnr budat blart
   into corresponding fields of table i_bkpf
   from bkpf
   where bukrs eq pa_bukrs
   and gjahr eq pa_gjahr
   and blart in so_DocTypes
   and monat in so_monat.
The report is taking too long and is eating up a lot of resources.
Any helpful advice is highly appreciated. Thanks!

Hi max,
I also tried using BUDAT in the where clause of my sql statement, but even that takes too long.
    select bukrs gjahr belnr budat blart monat
     appending corresponding fields of table i_bkpf
     from bkpf
     where bukrs eq pa_bukrs
     and gjahr eq pa_gjahr
     and blart in so_DocTypes
     and budat in so_budat.
I also tried accessing the table per day, but it didn't worked too...
   while so_budat-low le so_budat-high.
     select bukrs gjahr belnr budat blart monat
     appending corresponding fields of table i_bkpf
     from bkpf
     where bukrs eq pa_bukrs
     and gjahr eq pa_gjahr
     and blart in so_DocTypes
     and budat eq so_budat-low.
     so_budat-low = so_budat-low + 1.
   endwhile.
I think our BKPF tables contains a very large set of data. Is there any other table besides BKPF where we could get all accounting document numbers in a given period?

Report Takes Too Long Time

Hi!
I am in troubble
following is the query
SELECT inv_no, inv_name, inv_desc, i.cat_id, cat_name, i.sub_cat_id,
sub_cat_name, asset_cost, del_date, i.bl_id, gen_desc bl_desc, p.prvcode, prvdesc, cur_loc,
pldesc, i.pmempno, pmname, i.empid, empname
FROM inv_reg i,
cat_reg c,
sub_cat_reg s,
gen_desc_reg g,
ploc p,
province r,
pmaster m,
iemp_reg e
WHERE i.sub_cat_id = s.sub_cat_id
AND i.cat_id = s.cat_id
AND s.cat_id = c.cat_id
AND i.bl_id = g.gen_id
AND i.cur_loc = p.plcode
AND p.prvcode = r.prvcode
AND i.pmempno = m.pmempno(+)
AND i.empid = e.empid(+)
&wc
order by prvdesc, pldesc, cat_name, sub_cat_name, inv_no
and this query returns 32000 records
when i run this query on reports 10g
then it takes 10 to 20 minuts to generate report
how can i optimize it...?

Hi Waqas Attari
Pls study & try this ....
When your query takes too long ...
hope it helps....
Regards,
Abdetu...

OPM process execution process parameters takes too long time to complete

PROCESS_PARAMETERS are inserted every 15 min. using gme_api_pub packages. some times it takes too long time to complete the batch ,ie completion of request. it takes about 5-6 hrs long time ,in other time s it takes only 15-20 mins.This happens at regular interval...if anybody can guide me I will be thankful to him/her..
thanks in advance.
regds,
Shailesh

Generally the slowest part of the process is in the extraction itself...
Check in your source system and see how long the processes are taking, if there are delays, locks or dumps in the database... If your source is R/3 or ECC transactions like SM37, SM21, ST22 can help monitor this activity...
Consider running less processes in parallel if you have too many and see some delays in jobs... Also indexing some of the tables in the source system to expedite the extraction, make sure there are no heavy processes or interfaces running in the source system at the same time you're trying to load... Check with your Basis guys for activity peaks and plan accordingly...
In BW also check in your SM21 for database errors or delays...
Just some ideas...

Web application deployment takes too long?

Hi All,
We have a wls 10.3.5 clustering environment with one admin server and two managered servers separately. When we try to deploy a sizable web application, it takes about 1 hour to finish. It seems that it takes too long to finish the deployment. Here is the output from one of two managerd server system log. Could anyone tell me it is normal or not? If not, how can I improve this?
Thanks in advance,
John
+####<Feb 29, 2012 12:11:03 PM EST> <Info> <Deployer> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1330535463373> <BEA-149059> <Module copyrequest of application copyrequest [Version=COPYREQUEST0002bb] is transitioning from STATE_NEW to STATE_PREPARED on server Pinellas1tMS3.>+
+####<Feb 29, 2012 12:11:05 PM EST> <Info> <Deployer> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <9baa7a67b5727417:26f76f6c:135ca05cff2:-8000-00000000000000b0> <1330535465664> <BEA-149060> <Module copyrequest of application copyrequest [Version=COPYREQUEST0002bb] successfully transitioned from STATE_NEW to STATE_PREPARED on server Pinellas1tMS3.>+
+####<Feb 29, 2012 12:11:06 PM EST> <Info> <Deployer> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1330535466493> <BEA-149059> <Module copyrequest of application copyrequest [Version=COPYREQUEST0002bb] is transitioning from STATE_PREPARED to STATE_ADMIN on server Pinellas1tMS3.>+
+####<Feb 29, 2012 12:11:06 PM EST> <Info> <Deployer> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1330535466493> <BEA-149060> <Module copyrequest of application copyrequest [Version=COPYREQUEST0002bb] successfully transitioned from STATE_PREPARED to STATE_ADMIN on server Pinellas1tMS3.>+
+####<Feb 29, 2012 12:11:06 PM EST> <Info> <Deployer> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1330535466809> <BEA-149059> <Module copyrequest of application copyrequest [Version=COPYREQUEST0002bb] is transitioning from STATE_ADMIN to STATE_ACTIVE on server Pinellas1tMS3.>+
+####<Feb 29, 2012 12:11:06 PM EST> <Info> <Deployer> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1330535466809> <BEA-149060> <Module copyrequest of application copyrequest [Version=COPYREQUEST0002bb] successfully transitioned from STATE_ADMIN to STATE_ACTIVE on server Pinellas1tMS3.>+
+####<Feb 29, 2012 1:00:42 PM EST> <Info> <Diagnostics> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1330538442300> <BEA-320143> <Scheduled 1 data retirement tasks as per configuration.>+
+####<Feb 29, 2012 1:00:42 PM EST> <Info> <Diagnostics> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1330538442301> <BEA-320144> <Size based data retirement operation started on archive HarvestedDataArchive>+
+####<Feb 29, 2012 1:00:42 PM EST> <Info> <Diagnostics> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1330538442301> <BEA-320145> <Size based data retirement operation completed on archive HarvestedDataArchive. Retired 0 records in 0 ms.>+
+####<Feb 29, 2012 1:00:42 PM EST> <Info> <Diagnostics> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1330538442301> <BEA-320144> <Size based data retirement operation started on archive EventsDataArchive>+
+####<Feb 29, 2012 1:00:42 PM EST> <Info> <Diagnostics> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1330538442301> <BEA-320145> <Size based data retirement operation completed on archive EventsDataArchive. Retired 0 records in 0 ms.>+
+####<Feb 29, 2012 1:10:23 PM EST> <Info> <Cluster> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <weblogic.cluster.MessageReceiver> <<WLS Kernel>> <> <> <1330539023098> <BEA-003107> <Lost 2 unicast message(s).>+
+####<Feb 29, 2012 1:10:36 PM EST> <Info> <Cluster> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1330539036105> <BEA-000111> <Adding Pinellas1tMS2 with ID -9071779833610528123S:entwl2t-vm:[7005,7005,-1,-1,-1,-1,-1]:entwl2t-vm:7005,entwl3t-vm:7007:Pinellas1tDomain:Pinellas1tMS2 to cluster: Pinellas1tCluster1 view.>+
+####<Feb 29, 2012 1:11:24 PM EST> <Info> <Cluster> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[STANDBY] ExecuteThread: '3' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1330539084375> <BEA-000128> <Updating -9071779833610528123S:entwl2t-vm:[7005,7005,-1,-1,-1,-1,-1]:entwl2t-vm:7005,entwl3t-vm:7007:Pinellas1tDomain:Pinellas1tMS2 in the cluster.>+
+####<Feb 29, 2012 1:11:24 PM EST> <Info> <Cluster> <entwl3t-vm.co.pinellas.fl.us> <Pinellas1tMS3> <[STANDBY] ExecuteThread: '4' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1330539084507> <BEA-000128> <Updating -9071779833610528123S:entwl2t-vm:[7005,7005,-1,-1,-1,-1,-1]:entwl2t-vm:7005,entwl3t-vm:7007:Pinellas1tDomain:Pinellas1tMS2 in the cluster.>+
Edited by: john wang on Feb 29, 2012 10:36 AM
Edited by: john wang on Feb 29, 2012 10:37 AM
Edited by: john wang on Feb 29, 2012 10:38 AM

Hi John,
There may be some circumstances like when there are many files in the WEB-INF folder and JPS don't use TLD.
I don't think a 1hour deployment is normal, it should be much more faster.
Since you are using 10.3.5, I suggesto you to install the corresponding patch:
1. Download patch 10118941p10118941_1035_Generic.zip
2. Uncompress the file p10118941_1035_Generic.zip
3. Copy the required files (patch-catalog_XXXXX.xml, CIRF.jar ) to the Patch Download Directory (typically, this folder is <WEBLOGIC_HOME>/utils/bsu/cache_dir).
4. Rename the file patch-catalog_XXXXX.xml into patch-catalog.xml .
5. Start Smart Update from <WEBLOGIC_HOME>/utils/bsu/bsu.sh .
6. Select "Work Offline" mode.
7. Go to File->Preferences, and select "Patch Download Directory".
8. Click "Manage Patches" on the right panel.
9. You will see the patch in the panel below (Downloaded Patches)
10. Click "Apply button" of the downloaded patch to apply it to the target installation and follow the instructions on the screen.
11. Add "-Dweblogic.jsp.ignoreTLDsProcessingInWebApp=true" to the Java options to ignore additional findTLDs cost.
12. Restart servers.
Hope this helps.
Thanks,
Cris

RPURMP00 program takes too long

Hi Guys,
Need some help on this one guys. Not getting any where with this issue.
I am running RPURMP00 ( Program to Create Third-Party Remittance Posting Run ) and while running it in test mode for 1 employee it takes too long .
I ran this in background during off hours , but it takes 19,000 + sec to run and then cancels .
The long text message is No entry in table T51R6_FUNDINFO (Remittance detail table for all entities) for key 0002485844    and     Job cancelled after system exception ERROR_MESSAGE
I check the program and I found a nested loop within the program (include RPURMP02 ) and decided to debug it with a break point.
It short dumped and here is the st22 message and source code extract.
      ----Message -
" Time limit exceeded ".
"The program "RPURMP00" has exceeded the maximum permitted runtime without
Interruption and has therefore been terminated."
      ----Source code extract -
Include RPURMP02
172 &----
173 *&      Form get_advice_info
174 &----
175 *       text
176 ----
177 * --> p1        text
178 * <-- p2        text
179 ----
180 FORM get_advice_info .
181
182 * get information for advice form only if vendor sub-group and
183 * employee detail is maintained
184   IF ( NOT t51rh-lifsg IS INITIAL ) AND
185      ( NOT t51rh-hrper IS INITIAL ).
186
187 *   get remittance items employee number
188     SELECT * FROM t51r4 WHERE remky = t51r5-remky. "#EC CI_GENBUFF "SAM0632658
189 *     get payroll seqno determined by PERNR and RDATN
>>>>>       SELECT * FROM t51r8 WHERE pernr = t51r4-pernr
191                             AND rdatn = t51r5-rdatn
192                             ORDER BY PRIMARY KEY. "#EC CI_GENBUFF
193         EXIT.
194       ENDSELECT.
Has anyone ever come across this situation? Any input from anyone on this?
Regards.
CJ

Hi,
What is your SAP version?
Have you checked if some OSS notes is there on performance.
Regards,
Atish

AME CS6 rendering with AE and Pr takes too long

Hi Guys,
Need some help here. i have rendered a 30 secs mp4 video with 1920 x 1080 HD format 25 frames w/o scripting in AME for 4 hours!
Why does it take too long? I have rendered a 2 minute video with same format w/ scripting but only spare less than 30 minutes for rendering.
Im using After Effects and Premium Pro both CS6 and using Dynamic Link in AME.
What seems to be wrong in my current settings?
Any help would be appreciated.
Thanks!

This may be a waste of time, but it won't take a minute and is something you should always do whenever things go strangely wrong ............ trash the preferences, assuming you haven't done it already.
Many weird things happen as a result of corrupt preferences which can create a vast range of different symptoms, so whenever FCP X stops working properly in any way, trashing the preferences should be the first thing you do using this free app.
http://www.digitalrebellion.com/prefman/
Shut down FCP X, open PreferenceManager and in the window that appears:-
1. Ensure that only FCP X is selected.
2. Click Trash
The job is done instantly and you can re-open FCP X.
There is absolutely no danger in trashing preferences and you can do it as often as you like.
The preferences are kept separately from FCP X and if there aren't any when FCP X opens it automatically creates new ones . . . instantly.

My Query takes too long ...

Hi ,
Env   , DB 10G , O/S Linux Redhat , My DB size is about 80G
My query takes too long , about 5 days to get results , can you please help to rewrite this query in a better way ,
declare
x number;
y date;
START_DATE DATE;
MDN VARCHAR2(12);
TOPUP VARCHAR2(50);
begin
for first_bundle in
select min(date_time_of_event) date_time_of_event ,account_identifier ,top_up_profile_name
from bundlepur
where account_profile='Basic'
AND account_identifier='665004664'
and in_service_result_indicator=0
and network_cause_result_indicator=0
and   DATE_TIME_OF_EVENT >= to_date('16/07/2013','dd/mm/yyyy')
group by account_identifier,top_up_profile_name
order by date_time_of_event
loop
select sum(units_per_tariff_rum2) ,max(date_time_of_event)
into x,y
from OLD_LTE_CDR
where account_identifier=(select first_bundle.account_identifier from dual)
and date_time_of_event >= (select first_bundle.date_time_of_event from dual)
and -- no more than a month
date_time_of_event < ( select add_months(first_bundle.date_time_of_event,1) from dual)
and -- finished his bundle then buy a new one
date_time_of_event < ( SELECT MIN(DATE_TIME_OF_EVENT)
                         FROM OLD_LTE_CDR
                         WHERE DATE_TIME_OF_EVENT > (select (first_bundle.date_time_of_event)+1/24 from dual)
                         AND IN_SERVICE_RESULT_INDICATOR=26);
select first_bundle.account_identifier ,first_bundle.top_up_profile_name
,FIRST_BUNDLE.date_time_of_event
INTO MDN,TOPUP,START_DATE
from dual;
insert into consumed1 VALUES(X,topup,MDN,START_DATE,Y);
end loop;
COMMIT;
end;

> where account_identifier=(select first_bundle.account_identifier from dual)
Why are you doing this? It's a completely unnecessary subquery.
Just do this:
where account_identifier = first_bundle.account_identifier
Same for all your other FROM DUAL subqueries. Get rid of them.
More importantly, don't use a cursor for loop. Just write one big INSERT statement that does what you want.

Sql Query takes too long to enter into the first line

Hi Friends,
I am using SQLServer 2008. I am running the query for fetching the data from database. when i am running first time after executed the "DBCC FREEPROCCACHE" query for clear cache memory, it takes too long (7 to 9 second) to enter into first
line of the stored procedure. After its enter into the first statement of the SP, its fetching the data within a second. I think there is no problem with Sqlquery. Kindly let me know if you know the reason behind this.
Sample Example:
Create Sp Sp_Name
as
Begin
print Getdate()
Sql statements for fetching datas
Print Getdate()
End
In the above example, there is no difference between first date and second date.
Please help me to trouble shooting this problem.
Thanks & Regards,
Rajkumar.R

i am running first time after executed the "DBCC FREEPROCCACHE" query for clear cache memory, it takes too long (7 to 9 second)
Additional to Manoj: A
DBCC FREEPROCCACHE clears the procedure cache, so all store procedure must be newly compilied on the first call.
Olaf Helper
[ Blog] [ Xing] [ MVP]

Aperture 2 - Launch/Quit takes too long

Similar Messages

Maybe you are looking for