Apex PA50 SPICE Model used in Multisim

Below I have pasted the SPICE code from Apex for their PA50 power amp. I tried using the component wizard in Multisim but when I run the simulation I get the following errors:
1st a popup) An error has been found in the Netlist, would you like to proceed anyway?
2nd if I proceed) ------ Checking SPICE netlist for Apex_PA50 - Saturday, July 20, 2013, 12:54:12 PM ------
SPICE Netlist Error in schematic RefDes 'u1', element 'xu1': Unexpected '6' found on subckt instance line - too many nodes or parameter value missing name.
SPICE Netlist Error in schematic RefDes 'u1', element '<unknown>': Due to errors, the subckt instance 'xu1' has been omitted from the simulation
======= SPICE Netlist check completed, 2 error(s), 0 warning(s) =======
You SPICE gurus out there know how I can get these kinds of Apex models into multisim? They really make great amplifiers.
Thanks
Robert Harker
*REVISION 2 18-MAR-2002
*REDUCED INTERACTION OF SLEW RATE WITH CHANGING SUPPLY.
* BEGIN OPAMP MACROMODEL PA50
* PINOUT ORDER +IN -IN OUT +VB -VB +VS -VS
.SUBCKT PA50 1 2 3 4 5 36 37
J1 10 1 8 JI1
J2 11 2 9 JI2
R3 12 8 1.34E+03
R4 12 9 1.34E+03
I2 12 5 4.50E-04
C1 12 5 5.00E-13
R5 12 5 5.45E+06
R1 4 10 1.59E+03
R2 4 11 1.59E+03
C2 10 11 1.67E-11
I1 4 5 2.64E-02
G1 6 15 11 10 6.28E-04
G2 6 15 12 15 2.81E-08
R6 6 15 1.00E+05
D1 6 15 DD
D2 15 6 DD
C3 6 7 7.50E-12
G3 15 7 15 6 1.00E+01
R7 7 15 1E3
D3 7 16 DD
V1 18 16 5.50E+00
D4 17 7 DD
V2 17 19 5.50E+00
RE1 15 0 0.001
E2 38 0 4 0 1
E3 39 0 5 0 1
R8 7 20 50
C4 20 15 5.80E-11
Q3 37 20 21 QOP
Q4 36 20 22 QON
Q5 36 21 29 QON
Q6 37 22 29 QOP
E4 41 36 38 36 0.69
E5 42 37 39 37 0.69
E6 18 0 41 0 1
E7 19 0 42 0 1
RY1 38 0 10E6
RY2 39 0 10E6
RY3 41 0 10E6
RY4 42 0 10E6
I3 36 21 5.36E-03
I4 22 37 5.36E-03
I5 37 36 1.0E-02
R15 29 3 8.5E-02
DC1 29 36 DO
DC2 37 29 DO
.MODEL DO D(CJO=10PF IS=1.26E-12 RS=2.38E-03)
.MODEL DD D(CJO=0.1PF IS=1E-17)
.MODEL DL D(CJO=3PF IS=1E-13)
.MODEL JI1 NJF (BETA=4.00E-03 IS=3E-16 VTO=-1)
.MODEL JI2 NJF (BETA=4.00E-03 IS=3E-16 VTO=-1.0050)
.MODEL QOP PNP (BF=2.35E+04 IS=1E-14)
.MODEL QON NPN (BF=2.35E+04 IS=1E-14)
.MODEL QLN NPN (BF=100 IS=1E-14)
.MODEL QLP PNP (BF=100 IS=1E-14)
* END OF OPAMP MACROMODEL
.ENDS
Solved!
Go to Solution.

Here goes the netlist. OOPS the netlist is more than 10000 characters so I attached a word document if that helps. Thanks
Attachments:
Multisim Apex PA50.doc ‏29 KB

Similar Messages

Multisim: LT1568 Spice modell, AC simulations

Hi,
I'm building an input stage to an ADC, and need to do some signal conditioning before sampling. I'm thinking of using LT1568 for Low-Pass filtering, but when doing simulations in Multisim 13.0 I'm not getting the results I'm expecting.
I've provided my schematic, which is configured as a 4-pole LP filter with cut-off frequency at 5 MHz. When simulating it act's as a HP filter for some reason..
I've tried LTSpice and everything works fine, and I've contacted LT (Linear Technology) to get help but they suggest me to stick with LTSpice, which is not ideal for me.
I tried to make my own spice-model from code/description I found on the internet but with no success. Perhaps due to limited knowledge of spice.
Attached is the schematic
Thanks in advance
Sebastian
Solved!
Go to Solution.
Attachments:
1568.ms13 ‏126 KB

Try this.
Attachments:
1568_fixed.ms13 ‏164 KB

I need the SPICE Model for DS1809 or the component in Multisim. Help mee!

Hey people, I need the SPICE Model for DS1809 (Digital Potentiometer) for Multisim. Does anybody have this?? Or any idea where to get. I searched for, but I coudn't find.
Thank you

Hi,
As you can see in this link the part is longer manufactured and it does not have a replacement.
In terms of functionality, you can try using the component PLL_VIRTUAL in Multisim to replace it in a high level simulation or create a new component of a replacement that you have the SPICE model of.
Let me know if you need any help.
Mahmoud W
National Instruments

I need the SPICE Model for MC145106 or the component in Multisim. Please

I need the SPICE Model for MC145106 or the component in multiSIM. Please!

Hi,
As you can see in this link the part is longer manufactured and it does not have a replacement.
In terms of functionality, you can try using the component PLL_VIRTUAL in Multisim to replace it in a high level simulation or create a new component of a replacement that you have the SPICE model of.
Let me know if you need any help.
Mahmoud W
National Instruments

I need the ISO124 SPICE Model, or the component on Multisim. Can anyone help me?

People, I need the ISO124 model. Does anybody know how I can find it??
Thank you soo much!

Hi,
The SPICE model for the ISO124 is not available by the manufacturer. You can try contacting them and make a request for the model, sometimes they provide it upon a customer request.
Mahmoud W
National Instruments

Who can help me with spice model thx

i have download a power mosfet spice model, then creat a new component in multisim
i copy the model directly into multisim but it does't work
who can tell me causation, or tell me how can i trun it to multisim model
thanks very much
spice model:
* PSpice Model Editor - Version 9.2.1
*$
*DEVICE=IXFN36N100,NMOS
* IXFN36N100 NMOS model
* updated using Model Editor release 9.2.1 on 03/06/04 at 13:01
* The Model Editor is a PSpice product hem.
.MODEL IXFN36N100 NMOS
+ LEVEL=3
+ L=2.0000E-6
+ W=52
+ KP=1.0353E-6
+ RS=10.000E-3
+ RD=.22254
+ VTO=4.7737
+ RDS=10.000E6
+ TOX=2.0000E-6
+ CGSO=208.54E-12
+ CGDO=7.5038E-12
+ CBD=23.424E-9
+ MJ=1.5000
+ PB=3
+ RG=10.000E-3
+ IS=8.8150E-6
+ N=2.2584
+ RB=1.0000E-9
+ GAMMA=0
+ KAPPA=0
*$

Like I told another user I am no expert on model files. I have tried this file and Multisim will not recongnize it. I would recommend the following procedure if you can do it. Go into the component wizard and create a default Mosfet Using the Model Makers.. This will give you the correct syntax for the model file that Multsim can understand. If you know what the parameters mean from Pspice file then you can edit the model after it is created for you in Multisim and plug the numbers into it from the Pspice file. This should create a model that would work in Multisim. This procedure is theoretical on my part and you would have to try it to see if it works for you. It is possible that you don't have the Model Makers depending on your version of Multisim. If that is the case then we will have to try another approach.
I do not know the meaning of the Pspice parameters (i.e what does the L=XXXXX and N=XXXXX actual stand for). If you are unable to do this then maybe the NI Team can decipher this for you and post a model file that would work for you.
I am going to have to study the various parameter on these files to find out their meaning so I can be of better assistance when it comes to these model files. Right now I just don't have the time since I recently acquired a job that takes up a fair chunk of my days. I will contin ue looking into this as times permits for me.
Message Edited by lacy on 11-11-2007 07:40 AM
Kittmaster's Component Database
http://ni.kittmaster.com
Have a Nice Day

Modelling error in Multisim's Tektronix TDS2024 FFT option

The user's manual for Tektronix TDS2024 mentions that a 1 Vrms signal will be displayed as 0 dB peak in the FFT view. However, when I connect a 1 Vrms source to Tektronix TDS2024 scope in Multisim, I get a peak at 3 dB. This is only possible if National Instruments is using peak value in 20 log(V1/Vref) forumla instead of the RMS value which an actual (i.e., physical) TDS2024 oscilloscope uses.
Could someone confirm if its really a mistake or is it supposed to be like that?
Thanks in advance.
(P.S. Attached is the Multisim file)
Attachments:
FFT modelling error in Multisim.ms13 ‏75 KB

You nailed it! In the (old SPICE) analyses everything is peak amplitude (as it is in MULTISIM's "signal" sources). NI's additon of RMS options to "power" sources and not changing the corresponding "AC Analysis" from peak to RMS kinda added to the confusion! It seems to me that MULTISIM should stick to one or the other for consistency and make it clear what it is! Most EEs likely think that RMS is the "default" whereas most CSs (like the origimal Berkeley SPICE developers) likely thought peak was (as in Asin(omega)).

Applicable Updates and Importing Spice Models

Two part question:
Just installed version 10.0.144 (as seen in help-about Multisim) from CD and since my company uses a proxy server, I will need to manually check for updates. How do I know which updates are available for this version ?
Next, and more importantly, I need to import externally developed Spice models, assign them a shape and be able to use them in a simulation. While you do have a method for importing a spice netlist, I do not see anything that applies to subckt models (files that contain a .subckt definition.

Hi there,
It is possible to configure the Multisim 10 updater to use a proxy server.
Launch the Support and Update Utility (SUU)
SUU will check for updates, but will fail if you haven't configured SUU to use the proxy server
On the main SUU window, click Settings
On the second tab labeled Internet Connection Settings, enter the settings for you proxy server
Click OK and restart SUU
The latest update of Multisim 10.0 will update your version to 10.0.343.
As for your second question, it is relatively easy to create symbols and components that use SPICE models. What you need to do is outlined in this tutorial: http://zone.ni.com/devzone/cda/tut/p/id/3173.
Hope that answered your questions.
Message Edited by yyao on 01-27-2009 01:02 PM
Yi
Software Developer
National Instruments - Electronics Workbench Group

RS-485 transceiver spice model

Multisim Experts,
I have been on the hunt for an RS-485 transceiver spice model. In particular the MAX489, or any comparable full duplex transceiver. After many hours sorting through web searches I have come up empty handed. I was able to locate IBIS models for the transceiver, but converting IBIS to Spice using Intusoft's conversion program has been unsuccessful. I was wondering if anyone knew a good resource on how to write Spice models from existing IBIS parameters or data sheets? Or if perhaps anyone knew where to locate RS-485 models on the web?
Thanks for your time.

Multisim uses both SPICE and XPSICE simulation engine and there should be plenty of resources available on the Internet relating for these topics. Here are links where you can find the manuals:
SPICE:
http://esaki.ee.boun.edu.tr/~talays/spice/spice.pdf
XSPICE:
http://users.ece.gatech.edu/~mrichard/Xspice/Xspice_Users_Manual.pdf
The models you sent me will not work as is, there are minor syntax issues that needs to be modified and for it to work and here is a list:
1. No 'Param' statements were declared but a couple of statements uses a variable as a value, they did defined variable and was commented out, I guess they expect you to manually change it. The variables I am referring to are RTR and RTF:
Look for these statements:
*DEFINE {RTR}= 53.731k ;2.68V/1.44ns
B3 300 850 I= V(830) > 1.2   ? 0 : V(300,850) / {RTR}
Just replace RTR with the value like this:
B3 300 850 I= V(830) > 1.2   ? 0 : V(300,850) / 53.731
2.                  There are many instances where xy_array were used and unfortunately, Multisim does not support this syntax and you need to split the table into x_array and y_array separately.
For example the original model looks like this:
xy_array = [
+   -6.000 ,   -2.360
+   -5.000 ,   -2.360
+   -4.000 ,   -1.800
You need to change it to this:
+ x_array [-6.000 -5.000 -4.000 …..]
+ y_array = [ -2.630 -2.360 -1.800 ….]
3.                  You need to remove the some commas in the model
Original model:
+ fraction = FALSE, input_domain = 0.0,
Change to:
+ fraction = FALSE input_domain = 0.0
4.                  There are several duplicate subckt names declared and you should make them unique. I simply added an extra number at the end.
The attached file contain the modified model and test circuit, I am not sure what this component is suppose to but I connected some power sources to it and was able to simulate without an error.
I hope this help.
Tien
Tien P.
National Instruments
Attachments:
RS-485.zip ‏82 KB

How to export spice model from master db

I can't find a menu option nor DB manager option to select a component and export the spice model. Msim 10.1 full academic version with paid update service.

Hi there,
There are a few different ways to extract a component's SPICE model:
Transfer > Export Netlist: This will export the netlist for your design. So to export the SPICE model for one component only, simply place it down alone and then export the netlist.
Component Properties > Model tab: This method involves copying/pasting from the Model tab of the Component Properties dialog
Open the Database Manager
Edit the component
Select the Model tab
Copy/paste the SPICE model into a text file
Save with .cir extension
SPICE Netlist Viewer: In Multisim 11, there is also the ability to save a netlist from the SPICE Netlist Viewer, which displays the netlist live within a pane of Multisim
Message Edited by NatashaB on 03-05-2010 01:35 PM
Natasha Baker
R&D Engineer
National Instruments
Join the NI Circuit Design Community
Follow Multisim on Twitter!

Another LM324 SPICE Model error

LM324 "generates" negative voltage in schematic with single power supply voltage.
Attachments:
IdiotTest#2.ms12 ‏105 KB
Test #2.jpg ‏214 KB

Hi,
The model you selected was made by Motorola and unfortunately, when this model was imported into Multisim, the comments to show what this model was designed for was removed. Some models will not work with single rail. I was able to find the library where this model came from and base on the comments, this op-amp model was designed for the following:
- Positive and Negative Slew Rate
- Quiescent Power Dissipation
- Maximum Positive and Negative
- Output Voltage Swing
- Input Bias Current
- Open Loop Voltage Gain
- Unity Gain Frequency
- Common Mode Rejection Ratio
(CMRR)
- Output Impedence (ac and dc)
- Output Short Circuit Current Limit
You can find the original model from here:
http://www.gunthard-kraus.de/Spice_Model_CD/Vendor%20List/Spice-Models-collection/motoramp.lib
The opemp have several models, try the one from TI
Tien P.
National Instruments

RTD Platinum sensor Spice model

Does anybody have a spice model or can show me how to make one for a 20 ohm platinum ptc sensor with self heating ? I need to simulate it in a closed loop bridge circuit, I am an old fart that normally just uses paper and changes parts but this circuit is all smd.
Thanks doug W

Doug,
I created a simple RTD model that you can try. Use the TEMP pin to supply the external environment temperature as a voltage signal.
Take a look at the SPICE model and you should be able to figure out what's going on. Basically, its just a variable resistor modeled as I=V/R(temp), where temp is the adjusted temperature, a function of the external temperature and the power across the device.
Hope that helps!
Max
National Instruments
Attachments:
RTD.ms10 ‏81 KB

Migrating Oracle forms to APEX 3.2 without using Forms2XML tool

Can we migrate Oracle forms to APEX 3.2 without using Forms2XML tool?

Hi Anoo,
In order to convert Oracle Forms to Oracle Application Express, using the Forms Conversion utility in Oracle APEX 3.2, you are required to convert your Forms Module (FMB) files to XML format, using the Oracle Forms to XML conversion tool, Forms2XML. I would recommend that you review Chapter 4 [Converting an Oracle Forms Application|http://download.oracle.com/docs/cd/E14373_01/migrate.32/e13368/appmgr_forms.htm] , in the Oracle Application Express Migration Guide Release 3.2
If you have any further questions relating to the Oracle Forms to Oracle Application Express conversions, I would recommend that you refer to the [Application Express|http://forums.oracle.com/forums/forum.jspa?forumID=137] forum.
I hope this helps.
Regards,
Hilary

What are variables or parameters in Apex and how to use them?

Hi
What are variables or parameters in apex and how to use them to connect and run BI Publisher Report
From Apex URL

Hello Kanaiya,
You should go here: http://www.oracle.com/technology/products/database/application_express/index.html
Look at "What is Oracle APEX?" then download the documentation and review the various PDF files that are available.
If you have a version of APEX installed and available, go through the 2-Day Application Express Developer's Guide followed by the Advanced Developer's Guide.
Good luck,
Don.

Model uses wrong logical source for aggregation

Hi all,
i faced with problem when my model uses the wrong logical source to display pre-aggregated data. I have 5 logical sources with pre-aggregtaed data for my fact table and use two dimensions for mapping these sources:
Dimension "Geography": Country->State
Dimension "Periods": Year->Quarter->Month->Day
source 1 (most derailed) - mapped to levels: DAY, STATE
source 2 - mapped to DAY, COUNTRY
source 3 - mapped to MONTH, STATE
source 4 - mapped to MONTH (only this level)
source 5 - mapped to MONTH, COUNTRY
When i run my request - measure by DAY - it uses source 2, instead of using source 1 as i supposed. Can anybody explain me why?
BR,
Alex

What am i understanding from here is BI server decided on the best way to get the job done. You are having day at source 1 and source 2. But source 2 is aggregated at higher level than the source 1 with respect to region dimension. So as a matter of fact the best source for day is source 2.

Apex PA50 SPICE Model used in Multisim

Similar Messages

Maybe you are looking for