APO DP - use of forecast settings

I am using APO DP V5.
In my planning area I have one set of forecast settings specifying a forecast key figure x, corrected history key figure, corrected forecast key figure, ex post key figure.
I have two master forecast profiles, one specifying forecast key figure x, another specifying a different forecast key figure y. They use univariate profiles which specify hsitory key figures a and b respectively.
If I run a forecast using the profile specifying forecast key figure x, all the key figures are populated correctly. If I now run a forecast using the profile specifying forecast key figure y, I see that the forecast key figure is populated correctly, but the corrected history, corrected fcst and ex post are not repopulated.
So, I assume I should have 2 different sets of forecast settings, each with their own set of connected key figures.
Is this correct?
Thanks,
Bob Austin, Atos Origin

Srinivas,
Thanks for your reply.
The key question is this:
If I have my two separate forecast key figures X and Y (based on history A and B), do I need 2 separate 'forecast settings' for the planning area,eg:
1st set:Fcst key fig X, corrected hist key fig D, corrected fcst key fig E, ex post F
2nd set: Fcst key fig Y, corr hist G, corr fcst H, ex post I
I think yes is the answer, to ensure that I have separate sets of data for my two sets of forecasts.
Regards,
Bob.

Similar Messages

APO DP - use of forecast strategy 60 (copy history)

I am using APO DP V5.
I need to understand how forecast strategy 60 (copy history) works.
Suppose I have a three year forecast horizon.
Can I use this to copy from last year's history into each of these 3 years?
Thanks,
Bob Austin, Atos Origin

Hi Bob.
The answer to your question is no. 12 months of history will only generate 12 months of forecast.
I would suggest that if this was a requirement then a macro could be used to generate such a forecast.
Hope this helps.
Mark

Forecast settings in the Material Master

Hello gurus
We want to set the forecast model as X ( Seasonal and trend ) and Model Selectionu2014u2018 as Au201D We are getting error message as A is not relevant for this model . Where to do the relevent config .
Please advice where to do the config for the number ranges for the alpha/beta/ factor in the settings
Thanks
JJ

Dear,
I didn't get your requirement. The system first calculates the basic value on the basis of historical data and then updates this value at the end of every period using the alpha factor.
The forecast profiles in SOP are different than those in the material master. In SOP, you can use one forecast profile to forecast a whole group of materials. In the material master, each material has its own forecast profile.
In MC88, enter the material number and plant and select version
For that varsion copy sales plan from the followinbg menu
Edit >create sales plan>Forecast
Copy sales plan to ptoduction plan
Edit>create production plan>sycronous to sales
Hope it will help you.
Regards,
R.Brahmankar

How can I set Office Communicator to use my Outlook settings

dears
i use the business exchange mail from vodafone egypt
in work i can use outlook to see my mails and also office communicator
but here in home i can only use OWA and outlook and i cannot set the Communicator to use my Outlook settings
i also tried to use the same settings that already set on the work but i cannot login to it
so please help me to open it
sorry about my English not good :)

Looking to do voice overs? See iMovie '11: Record a voiceover

Windows - Use system proxy settings not working as expected

Hi everyone,
I have a bit of an issue that I could use some help with. We currently have remote users that utilize an SSTP VPN connection to access our internal network. Once connected, those users are required to use an internal proxy server to connect to the Internet. The proxy server is Microsoft's TMG and utilized domain authentication.
On our remote Windows clients we have their Internet Options configured to utilize a proxy as follows:
Internet Options -> Connections -> LAN Settings -> No proxy configured at all
Internet Options -> Connections -> Highlight SSTP Connection -> Settings
Use a proxy server for this connection -> IP/Port of Proxy Server
Firefox and Chrome are both configured to use system proxy settings.
Here is my process to demonstrate the issues:
Remote client workstation is rebooted.
With the above configuration just after a reboot, a remote user that is not connected to the VPN can browse the Internet with Internet Explorer, Chrome, and Firefox. None of the browsers prompt for credentials.
A remote VPN connection is then established.
FF is opened and HTTP connections utilize the proxy server. However, HTTPS connections do not use the proxy server, but instead attempt to use the default gateway. FF does not prompt for credentials. FF is closed.
Chrome is opened and can access both HTTP and HTTPS sites without issue. No credential prompt. Chrome is closed.
IE is opened and can access both HTTP and HTTPS sites without issue. No credential prompt. IE is closed.
Here's where it gets weirder...
FF is then reopened. The VPN connection is still up. FF will prompt for credentials. Domain credentials are supplied and FF can now utilize the proxy for both HTTP and HTTPS connections. FF is closed.
VPN is disconnected.
FF is opened and cannot access the Internet as it is still trying to use the proxy server. FF is closed.
IE is opened and can access the Internet. IE is closed.
Chrome is opened and can access the Internet. Chrome is closed.
FF is reopened and can now access the Internet. FF is closed.
In summary, in the above scenario FF acts in an unexpected manner with regards to proxy usage when "use system proxy settings" is applied. However, Firefox begins acting as expected after IE is opened and closed. For example, connect to VPN, open IE, close IE, open FF, and everything works accordingly. Disconnect the VPN, open IE, close IE, open FF and everything works as expected.
Any insight you can provide would be appreciated as it is affecting our FF users and the sooner we can achieve resolution the better. As a note, we've also worked through this issue with WPAD and proxy auto-detect. I've intentionally removed these from the equation to simplify troubleshooting.
Thanks

Quick update. Added to a previously filed bug. Looks like it's assigned now so maybe we'll see a fix for this soon.
https://bugzilla.mozilla.org/show_bug.cgi?id=563169

Trying to sign in on itunes but keeps telling me id not used before review settings what can i do

trying to sign in on itunes but keeps telling me id not used before review settings and accept cookies checked every thing still cant get on can anyone help thank you

Try logging on to your accunt on a conoputer and then go to edit you account. Make sure that you account details are correct and the then save. It may be an Apple problems since some other have been have same or similar problem this morning.

Firefox not detecting/using system proxy settings

I use a command line script to change among various proxies (and none). Firefox does not recognize when a proxy is turned on or fails to connect to it (no error messages), while other browsers and applications do just fine.
I have tried selecting "Use system proxy settings" and "Auto-detect proxy settings for this network."
My script contains these lines to activate a proxy
reg add "HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Internet Settings\Connections" /v DefaultConnectionSettings /t REG_BINARY /d 46000000b10000000200000014000000736f636b733d3132372e302e302e313a313131311c0000002a2e6c6f63616c3b3139322e3136382e31312e2a3b3c6c6f63616c3e000000000000000000000000000000000000000000000000000000000000000000000000 /f
reg add "HKCU\Software\Microsoft\Windows\CurrentVersion\Internet Settings" /v ProxyEnable /t REG_DWORD /d 1 /f
reg add "HKCU\Software\Microsoft\Windows\CurrentVersion\Internet Settings" /v MigrateProxy /t REG_DWORD /d 1 /f
The first line enables the proxy to take effect without entering inetcpl.cpl. Again, this works for any application other than Firefox.
The proxies are all through ssh with port forwarding.
I do not want to manually configure a proxy in Firefox, because I do not want to change this every time I need to change proxies or turn them off. This is not an acceptable solution.
I am on Windows 8.1 64bit, with Firefox version 35.0
Any idea what might be going on here?

Thank you for the response, but as above, the "Auto-detect proxy settings for this network." setting does not work.

Two very different results using the same settings (H.264 / Quicktime Pro)

I’m a bit confused, I have used Quicktime Pro (v7.1) to encode DV into H.264 for iPod and this particular video is 18 minutes long and came out looking very good with the following settings;
VIDEO: H.264 at 200kbps, Baseline Profile, 25fps, Auto Key Frames, 320x240 or 640x480, Multipass Best quality encoding.
AUDIO: AAC Audio at 96kbps, 24kHz sampling freq, Stereo.
However here is the twist…
When I use the same exact settings to encode just the 30 second opener (from the 18 minute video) the encoded opener looks bad and blocky!
Why? Same settings would make you assume that you should get a same or similar result, or am I wrong?
The reason I have tried encoding this 30 second opener is that I am trying to work out which settings work best on the iPod (another issue) and I don’t want to spend hours test encoding the full 18 minute video, as you know H.264 is SLOW to encode!
So can anyone help in regard to two very different results using the same settings?
Regards,
J
PC Windows XP

Alvin,
Is it a commercially-released or home-burned CD?
If it's commercially-released, try "encouraging" the recalcitrant computer by using the iTunes Advanced menu > Get CD Track Names command when it shows Audio CD.
If it's home-burned, you will find that only the computer that actually burned the disc will know what's on it. The information won't be transferred to another computer.
Let us know which, if either, of these situations applies to you.

Can lync client use internet proxy settings to proxy edge servers, if direct access is not reachable?

Hi everybody I am trying to Login with my lync Client out of my organization. So I am using lync as a remote user. I am in another organization, and I am using their coporate lan wired and wireless, but I cannot Login to lync in my organization.
I see that I cannot Access my edge Server on port 443 to authenticate directly, I know that Client in this organization use Internet Proxy to browse the Internet. they have a .pac in their ie Settings.
my question is; can lync Client use Internet Proxy Settings to reach the Destination? I mean the Access edge on port 443?
or it can use only Client direct Access to reach the edge Servers?
I Think that the answer is that I use tcp protocol and not http, and maybe that is the reason why I cannot use the Internet Explorer Proxy Settings to reach the Access edge Servers, different maybe is the case I Need to reach the reverse Proxy for live Meetings.
Hope my question is clear.
Thanks

Proxy settings are used to tell Internet Explorer the network address of an intermediary server (known as a proxy server) that is used between the browser and the Internet on some networks.
Lync client doesn’t use Internet Proxy Setting. You need to access the Edge service directly.
Lisa Zheng
TechNet Community Support

How to avoid Java Studio Creator 2 to use the regional settings?

How to avoid Java Studio Creator 2 to use the regional settings to select the language that will be used to display the IDE in a certain language?
My country settings are set to Belgium (French) but I want to have my IDE running in English.
What should I change in the defautl properties of JSC2 to avoid this behaviour?
Please, don't tell me to change my regional settings, it is not a valid answer :-)
Best regards,
Abdelkrim BOUJRAF

just modify creator.conf in directory etc/
add: -J-Duser.language=en
in the netbeans_default_options line:
like this:
netbeans_default_options="-J-Duser.language=en -J-Xms96m -J-Xmx384m -J-XX:PermSize=32m -J-XX:MaxPermSize=128m -J-XX:+CMSClassUnloadingEnabled -J-XX:+CMSPermGenSweepingEnabled -J-Xverify:none -J-Dnetbeans.javacore.background_scanning=true -J-Dsunappsrvint.home=\"C:\Program Files\Sun\Creator2\SunAppServer8\""

Is my graphics card too under-powered to use the graphics settings in the 64bit CS 6

I cannot get certain filters to work in 64bit CS6 as it will not let me used the GPS settings because it seems to think my driver is not installed properly. I have reinstalled the latest driver to no avail. In 32 bit CS6 I have no problems at all.
I am using a Dell M4700 workstation with a AMD Firepro M4000 (FireGL V) on the Windows 7 operating system.
Is my graphics card too underpowered to use the graphics settings or are there other issues involved?

I don't know AMD cards, but I just looked up the notebook, and that is a very capable little system, so I really think it should be OK. The bottom line, as you have already stated, is that it needs an up to date driver. Where did you find your 'latest' driver?
If you got it from Dell or Microsoft, then you could likely end up with an out of date driver, so you need to go to the AMD site.
http://www.amd.com/US/PRODUCTS/WORKSTATION/GRAPHICS/ATI-FIREPRO-MOBILITY/Pages/ati-firepro -mobility.aspx
AMD have an auto update tool here, but you will probably need Java installed
http://support.amd.com/en-us/download

Editing LAN settings in GP using only computer settings

billyrobinson2 wrote:I have my GPO applied to the folder just containing the laptops, so in theory, I shouldn't need item-level targeting, correct?Correct.billyrobinson2 wrote:I have my GPO applied to the folder just containing the laptops, so in theory, I shouldn't need item-level targeting, correct?It's not so much the item that is the issue, it's how you apply the LAN settings, which are mostly user based. If you go to user configuration - Preferences - Control Panel - Internet settings, you can very easily make these changes, but they are user based.If I apply this change at a user level however, can I do item-level and tell it just to apply to the laptops? I'll test it outYes that would work, as long as the user objects / security group is within the scope and security filtering of the GPO.For example:User 1 logs onto Laptop1 -...

Hi All
I need to edit the IE LAN settings in GP using only computer settings. The changes I'm making are going to be applied to laptop users only, I don't want the settings applied to users as our users connect in various different ways (Desktops, laptops, so on)
The changes I'm making cannot affect the desktops, only the laptops & it cannot affect all users, only laptop users.
Tricky I know, but does anyone know how to do this? my Google searches have been unsuccessful so far!
Thank you
Bill
This topic first appeared in the Spiceworks Community

I can't turn my email or message notifications off. I have used the off settings, but still no luck?

I can't turn my email or message notifications off. I have used the off settings, but still no luck?

Are you talking about turning off the alert sound when you receive messages and email? If so, go to Settings>Sounds>New Mail>scroll to the top and choose None. Do the same for Text Tone.

File Export use last usage settings of File Export Wizard

how convert a color photo to grayscale? cs6 fireworks / adobe cloud,... File > Export use last usage settings of File > Export Wizard???

There are a lot of different ways to create greyscale images. Here are three methods:
Select the bitmap and choose Commands > Creative > Convert to Grayscale.
This is a quick but destructive method, meaning that it modifies your original image. To preserve your original image, you could first make a copy using the Edit > Clone command.
Select the bitmap and apply a Hue/Saturation effect.
This effect can be found in the Properties panel within the Filters menu, under Adjust Color. Set Saturation to -100.
Select the bitmap and apply the Convert to Alpha effect.
This effect can be found in the Properties panel within the Filters menu, under Other. Set the document canvas to White.
At least one of these should work for you.
Unfortunately, I can't quite understand the portion of your question regarding File > Export and the Export Wizard. If English is not your native language, you might try using Google Translate to compose your question.

BO 4.0 LCM - Using the Override Settings Option

I am reading the LCM user manual and I am wondering:
What is meaning of Using the Override Settings Option?
I need to use LCM to move WebI reports and Universes from one environment to another
and from one environment to a LCMBIAR file.

I did everything as advised to apply an override for the universe connection object, even though there is no change in the connection settings from QA to PROD, I still get this during Test Promote:
Resolution Status=Copied, Dependency Status=All the required dependencies are included., Commit Status=Commit is successful., Promotion Status=Warning : Can't apply override; Override information is Not Available
When I do the actual promotion, the job fails for the connection object citing override issues. I don't know what's going on with LCM but is there any way to no be forced to use the override feature?
Thanks!

APO DP - use of forecast settings

Similar Messages

Maybe you are looking for