App Error 200???? Desktop Manager not connecting to Device??

I am officially out of ideas for what to do with my phone!!
I changed my pay as you go tariff yesterday and in order to reset the phone to get my internet settings I switched off the handset and turned it on again.
When I turned it back on it started to load as normal then came up with "App Error 200" message. I have done a hard reset and even after taking out the sim and battery it still wont work.
I know I can change things on my Desktop Manager, but that now wont recognise the phone is connected. I have gone to the 'Options' button (top right hand corner) and applyed the USB connection but is still wont work!!
Can anyone help as I am totally lost and have lost all patients!!!!
Thanks

If that still doesn't work you will need to do the following:
http://www.blackberryfaq.com/index.php/How_do_I_wipe_the_BlackBerry_using_Jl_Cmder%3F
http://www.blackberryfaq.com/index.php/What_to_do_next_if_Jl_Cmder_will_not_connect_and_wipe
Then reload the OS from the thread below:
http://www.blackberryforums.com/general-8900-series-discussion-javelin/227412-os-8900-v5-0-0-1168-5-...
You can use the OS in the download link in the thread above or you can download from your own carrier (doesn't matter where it comes from) but be sure and use the instructions in the above thread to install it.
If you didn't have a backup from before this happened you will lose your data.
1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

Similar Messages

Desktop manager not connecting with the 9700 bold

hi,
I am using a 9700 bold, i updated to the latest desktop manager and since then when ever i open the destop manager an error message comes in ( RIM handheld communications manager has stopped working) Can any one one tell me what that is, i have tried uninstalling and going back to a older version but nothing seems to work, please help me, thought the phones charges and it back ups in the older version of desktop manager but the mass storage device option osent show up??
Rregards,
mubashir

hi,
I am using a 9700 bold, i updated to the latest desktop manager and since then when ever i open the destop manager an error message comes in ( RIM handheld communications manager has stopped working) Can any one one tell me what that is, i have tried uninstalling and going back to a older version but nothing seems to work, please help me, thought the phones charges and it back ups in the older version of desktop manager but the mass storage device option osent show up??
Rregards,
mubashir

Comp/ Desktop Manager not recognizing plugged device

I recently installed/ updated the BB Desktop Software and when I plug in my BB Curve 8520, my comp doesn't recognize the device.
Note 1: I've installed all updates on my computer AND the new OS on my phone already.
Note 2: My phone recognizes that it's plugged into the computer because begins to charge.

Hi and Welcome to the Forums!
Here is the list of troubleshooting articles...hopefully something will be useful:
http://supportforums.blackberry.com/t5/BlackBerry-Desktop-Software/Tips-for-getting-BlackBerry-Deskt...
KB02640 Troubleshooting USB connections
KB15486 Top 10 BlackBerry smartphone and BlackBerry Desktop Manager troubleshooting tips
KB11439 BlackBerry Desktop Software does not detect the BlackBerry smartphone when it is connected
KB00019 No PIN displayed in BlackBerry Desktop Redirector
KB10938 "USB charging current is insufficient" appears on the BlackBerry smartphone
KB01451 How to turn on advanced synchronization logging if a wired synchronization fails
KB19717 The BlackBerry smartphone is not detected as a USB Mass Storage Device when connected to a computer
KB16310 Media Transfer Protocol and the BlackBerry Storm smartphone
http://supportforums.blackberry.com/t5/BlackBerry-Desktop-Software/Desktop-Manager-quot-disconnected...
Also, check that you are using only root USB ports...no hubs (sometimes the front-side ports are hubs...use a rear USB port). And make sure to try disabling USB power management in your system configuration (Device Manager).
Also check on conflicting software...it has been reported that the software package NTI Shadow&Ninja can cause a conflict; removing them and reinstalling the BB desktop software allows it to install correctly.
Apologies in advance if this is redundant -- there's no way to be sure if you've already seen and tried these.
Hopefully something there is helpful!
Cheers!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Cannot connect to PC. App Error 200 keeps coming up.

I have a BlackBerry Curve 9380. While charging the battery an update came up on the PC to download. Since downloading the update, I cannot turn the phone on or navigate. The Blackberry name comes up and the line scrolls across the bottom then a white screen with App Error 200 (Reset) shows on the screen. When I reset, it goes through the same things and then stays on. I took it to a Bell store and they could not correct this problem and suggested I try you. I have tried reloading the desktop software, and taking the battery out and the problem still exists. Any help you could provide would be much appreciated.

Hello lilbet,
Welcome to BlackBerry Support Forums
Please try this Knowledge Base to resolve your issue with this Error :
KB11320 : How to perform a clean reload of the BlackBerry Device software using BlackBerry desktop software for windows
I hope you already have a backup of your device , Or if you device allow first do a backup .
Additional Information can be found here :
KB30100 : "JVM 200" appears on the BlackBerry smartphone.
Try it and let us know if you feel any issue.
VIA | prince2012
http://supportforums.blackberry.com/t5/BlackBerry-Curve/error-app-200/m-p/2484385#M200531
Please thank those who help you by clicking the button.
If your issue has been solved, please resolve it by marking "Accept as Solution"

App Error 200

After installing an uodate to PocketGrapes Digital Wine Diary last night I was prompted for a Restart which I accepted. The Restart gets no further than the white line across the bottom of the Blackberry screen which hangs for about 5 minutes and then shows App Error 200. If I accept Reset the process is repeated. If I remove the battery and then replace it the same thing happens.
I have tried to Restart in Safe mode but this does not work.
I have tried to Reload the OS from Blackberry Desktop Software but when I connect my phone, the phone restarts and I get the Error message: "Cannot communicate with the connected device" because it is rebooting. The only way I can stop it from rebooting is by taking the battery out but if I then try and connect my phone I get the same error message bacause the software thinks the battery is flat.
Any advice would be welcome.
Solved!
Go to Solution.

Hello gillalwyn23
Welcome to BlackBerry Support Forums
Do you have a backup of your device ? You may need it .
Refer to this Knowledge Base and try those suggestion :
KB10144 : How to force the detection of the BlackBerry smartphone using Application Loader
Please note , this method will data all user data within that device but you'll may be ab;le to get your device back in order , if you have a previous backup or using BlackBerry Protect you can restore it from there.
Additional Information :
KB30100 : "JVM 200" appears on the BlackBerry smartphone.
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.

App Error 200 - Reset, BB curve 8520

Hello,
While I was downloading the new BB software via BB desktop manager, my laptop suddenly closed. After that, when I re-opened my mobile, after reloading, the screen went blank with an "App Error 200 - Reset" in the middle of the screen. I tried pressing the reset button, but it repeats the same system again! How can I solve this problem?! Pleasee Help

Just enter an incorrect one 10 times and the phone will reset itself back to factory settings without a password and then you are good to go. (P.S: note that the device wont lock out it will start fresh as a new device). Have you made a back-up of your BB at any given point in time?
If so, then you can just load the backup through the Desktop Manager.
Please follow the below threads and would give you some more idea on the issue and a feasible solution if mine doesnot satisfy you:
http://supportforums.blackberry.com/t5/BlackBerry-Bold/Device-Lock-Password-reset/td-p/1125369
http://supportforums.blackberry.com/t5/Desktop-Software-for-PC/BlackBerry-device-password-does-not-w...

BB Bold 9900 APP ERROR 200.....HELP!!!

I have a BB Bold 9900 and has the white screen with App Error 200 Reset screen, I have tried taking the battery out and plugging it into computer to reset it but comes up with the update screen and then says repair and then says No BB device updates available...what do I do now as just have an exspensive brick????? thanks

Hi and Welcome to the Community!
Here is a KB that discusses that error:
KB30100 "JVM 200" appears on the BlackBerry smartphone
Hopefully it contains something useful! There also are multiple existing threads on this site that discuss that exact error...your review of those might prove useful, and a search of this site, using the error message, error code, or symptom, should reveal all applicable existing threads to you.
You also might want to do an OS reload. The simplest way is to, on a PC (you cannot do this on MAC):
1) Make sure you have a current and complete backup of your BB...you can find complete instructions via the link in my auto-sig below.
2) Uninstall, from your PC, any BB OS packages
3) Make sure you have the BB Desktop Software already installed
http://us.blackberry.com/software/desktop.html
4) Download and install, to your PC, the BB OS package you desire:
http://us.blackberry.com/support/downloads/download_sites.jsp
It is sorted first by carrier -- so if all you want are the OS levels your carrier supports, your search will be quick. However, some carriers are much slower than others to release updates. To truly seek out the most up-to-date OS package for your BB, you must dig through and find all carriers that support your specific model BB, and then compare the OS levels that they support.
5) Delete, on your PC, all copies of VENDOR.XML...there will be at least one, and perhaps 2, and they will be located in or similarly to (it changes based on your Windows version) these folders:
C:\Program Files (x86)\Common Files\Research In Motion\AppLoader
C:\Users\(your Windows UserName)\AppData\Roaming\Research In Motion\BlackBerry\Loader XML
6a) For changing your installed BB OS level (upgrade or downgrade), you can launch the Desktop Software and connect your BB...the software should offer you the OS package you installed to your PC.
6b) Or, for reloading your currently installed BB OS level as well as for changing it, bypass the Desktop Software and use LOADER.EXE directly, by proceeding to step 2 in this process:
http://supportforums.blackberry.com/t5/BlackBerry-Device-Software/How-To-Reload-Your-Operating-Syste...
Note that while written for "reload" and the Storm, it can be used to upgrade, downgrade, or reload any BB device model -- it all depends on the OS package you download and install to your PC.
If, during the processes of 6a or 6b, your BB presents a "507" error, simply unplug the USB cord from the BB and re-insert it...don't do anything else...this should allow the install to continue.
You may also want to investigate the use of BBSAK (bbsak.org) to perform the wipe it is capable of.
You may also want to try the "Bare Bones OS Reload Procedure" to attempt to narrow down the precise causal item:
Load your OS "bare bones"...if anything is optional, do not install it.
If the behavior presents immediately, then try a different OS with step 1
If the behavior does not immediately present, then run for as long as it takes for you to be sure that the behavior will not present.
Add one thing -- no matter how tempting, just one.
If the behavior does not present immediately, then again run for long enough to be sure it will not have the same problem
Repeat steps 4 and 5 until all things are loaded or the behavior presents
When the behavior presents, you know the culprit...the last thing you loaded.
If the behavior does not re-present, then you know that either step 1 or 2 cured it.
If the behavior presents no matter what, then you likely have a hardware level issue for which no amount of OS or software can cure.
You may also need the use of these tricks:
KB10144 How to force the detection of the BlackBerry smartphone using Application Loader
KB27956 How to recover a BlackBerry smartphone from any state
http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry
If you are on MAC, you are limited to only your carriers sanctioned OS packages...but can still use any levels that they currently sanction. See this procedure:
KB19915How to perform a clean reload of BlackBerry smartphone application software using BlackBerry Desktop Software
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

App error 200 reset??? help me

Hi,
Can anyone help?
I was doing a update but then accidently unppluged the phone so my blackberry torch started to reboot, it took a while then white screen App error 200 reset shows up i push it and then it trys to reboot again but same app error 200 reset over and over again. how can this be fixed?

Try the method above, which circumvents Desktop Manager. If that doesn't work, post back and we'll try some other things. In fact, go ahead and download an app to your PC called BBSAK, which you get here: www.bbsak.org
Once the app is installed, connect your device to the PC, then launch BBSAK. You'll be asked for a password. If you don't have a password set for your device, just click OK.
Your device should hopefully be recognized by BBSAK, in which case, choose the Wipe Device option. This will wipe the OS from your device, allowing you to do a fresh install using the instructions above.
*** If I've been helpful please consider clicking the LIKE BUTTON beneath my post.
*** Please remember to mark your thread as "Resolved" by clicking on OPTIONS to the right of the post and selecting "Accepted Solution."

App error 200 while updating my device software

Could anyone please give me some advice?
I was updating my Blackberry device software and after the update had finished was prompted to restart my system and the phone but my phone has since refused to come on. it keeps showing 'App Error 200' reset
The issue is that my blackberry is loading when the battery is removed and inserted again, but won't log in. After a while a white screen is displayed with the following message: App Error 200 and Reset just below it.
When I select the reset option, the above mentioned process just repeats itself.
My Blackberry desktop application does not even recognise up my phone once it is plugged in again.
please i would appreciate any help to correct this error and regain the use of my phone

i tried this one & it worked
http://btsc.webapps.blackberry.com/btsc/viewdocument.do?externalId=KB10144&sliceId=2&cmd=displayKC&d...
or
http://btsc.webapps.blackberry.com/btsc/viewdocument.do?noCount=true&externalId=KB03901&sliceId=2&cm...

Bb app error 200 impossible to restart

hey
i have a bb curve 9360 n suddenly it got switched off n on, showing app error 200 reset.
i tried to connect it to desktop software n update it but it shows fatal error while updating.
i am stuck with no idea what to do now.
any help would be greatly appreciated

You have to reload the same OS.
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up Blackberry Battery Saving Tips | Follow me on Twitter

Curve 8520: app error 200

I have a 8520. I tried deleting an app using the bb desktop software. At the end of the task I got the message "can't connect with the device". The device keeps saying "app error 200". What do I do?

I have a 8520. I tried deleting an app using the bb desktop software. At the end of the task I got the message "can't connect with the device". The device keeps saying "app error 200". What do I do?

Hp recovery on laptop gives error message "destination drive not connected"

I'm trying to carry out factory reset on my 2012 G6 laptop product code B2Y48EA*ABU serial no. [Personal Information Removed] to factory settings using set of 5 recovery discs
I followed the procedure shown here (although the screen messages are slightly different)
http://support.hp.com/gb-en/document/c01867418
I started the laptop with disc 1 in the dvd drive and the hp program was displayed. I selected "factory reset" and followed promts
When the 4 th disc is in dvd drive and the process is about53% compltete it stops with the error message
"destination drive not connected"
and fails
Earlier the recovery manager reported that the partion on the hard drive had been re-forrmatted so the drive was connected then!
All help and suggestions appreciated

Hi there @Teka,
I understand that you are having trouble with a System Recovery to a factory image using recovery disks. I am happy to help you with this.
Are those five disks a set that you created using the recovery manager, or is it a set you ordered from HP?
Is there any sign of damage, scratches or smudges on the disk it fails on?
Have you tried cleaning the DVD drive?
Also take a look through these pages, in particular the troubleshooting page, and see if anything there is of use.
Performing an HP System Recovery (Windows 7)
Troubleshooting HP System Recovery Problems (Windows 7)
Let me know how it goes for you.
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

App error 200 on Torch 9800

Got an App error 200 on my Black. Been trying to restart and restart and restart but still it freeze during the process and still getting the App error 200 and the only thing my black allows me to do is to restart !!!!!
Was on Blackberry World trying to install Slacker radio when it all started
Took the Sim and SD card to see if it would change anything but still having the same problem
Does anyone know what can be done to fix this ?

Hello Solem
Welcome to BlackBerry Support Forums
Please try this Knowledge Base to resolve your issue with this Error :
KB11320 : How to perform a clean reload of the BlackBerry Device software using BlackBerry desktop software for windows
I hope you already have a backup of your device , Or if you device allow first do a backup .
Additional Information can be found here :
KB30100 : "JVM 200" appears on the BlackBerry smartphone.
Try it and let us know if you feel any issue.
Credits:
prince2012
Solution:
http://supportforums.blackberry.com/t5/BlackBerry-Torch/App-Error-200/m-p/2476845#M65764
Please thank those who help you by clicking the button.
If your issue has been solved, please resolve it by marking "Accept as Solution"

Error message "app error 200"

I have an app error 200 on my phone. how do i fix it? Wont let me reset.

An sdn search gave me this thread to create custom SOAP envelop
Generating SOAP Envelope when DO NOT USE ENVELOPE option is marked

HT201299 Verizon signal is strong but get error message "Ipad is not connected to the Internet"   Wireless works but my Verizon account does not

Verizon signal is strong but get error message "Ipad is not connected to the Internet"   When I try to use Safari.
Wireless works but my Verizon account does not

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

App Error 200???? Desktop Manager not connecting to Device??

Similar Messages

Maybe you are looking for