Apple Airport Express - Scientific Atlanta Modem

I purchased a new Apple Airport Express to be used with a Time Warner Scientific Atlanta Modem. All connections are via RJ 45 cables. Apparently the AE is unable to make the proper IP adjustments beginning 198 (currently it is set on IP adress beginning 164). I called TW tech support, of course they say it is an Apple issue and no their problem. I tried killing all devices and rebooting the modem after 15 minutes, followed by the AE after 15 minutes, then turned on the iMac. No change...same IP address. Any advice is appreciated.

Power up the Express for a few minutes
Hold in the reset button on the Express firmly for 10 seconds
Allow a full minute for the Express to restart
If Mavericks or the iOS devices cannot see the Express, you have a defective Express.
Note....the Express will not "boost" or "extend" the signal from your wireless router wirelessly....unless you have another Apple router.

Similar Messages

So does the Apple Airport Express take the place of the "Charter" modem and router we already have in our house?

We purchased the Apple Airport Express and in our home have 2 iPads, 2 iPhones, 1 iPod, 1 MacBook, and two *D* computers and a Brother printer along with Apple TV and a projector.
1. How do we get them all to mirror the content of the various devices onto the TV or the projector?
2. Can we now unplug the *Ch* equipment from our cable source and plug in the airport express?
Putting all the pieces together is just a little beyond us at this moment. Maybe it will click with a little help. Thanks!
"Stuck" in Montgomery

I'm pretty sure you will find that the Airport Express will not work with your router unless it's an Airport Extreme Base Station.
You can do two things with the Airport Express. You can connect it by USB or Ethernet cable to a device like a printer that does not have wireless capability and provide a wireless connection to your router provided the two devices will "talk" to each other.
You can connect it to a Mac to provide audio streaming wirelessly.
You may be able to use it with your projector provided it has its own wireless capability, but I don't know if an Airport Express will stream video. Same for your TV.
In fact for your home I'm not sure the AEX would be of much use except to connect to your Mac in order to stream audio to another wireless device in your home. But only if you can get the AEX to work with your router or replace the router with an AEBS (which you could only do if your current router is a discrete device connected to your Charter cable modem.)

Apple Airport Express: How To Change IP Address While in Bridge Mode

Hello, I have a Apple Airport Express router and it has been good for a few years. Just wondering how to change my public IP address. I am also in Bridge mode to a cisco router. Also I am on a Windows 8 computer and this is mainly what I want to change the ip for.

Power cycle the cable modem.. I presume that is what the cisco router is.. your modem.. if not tell us precise model and make of the modem.
The public IP is not changed by you.. it is changed by your ISP.. normally if you power cycle the modem on a dynamic system you will get a new IP.. if not call the ISP and request them to make a change.
It is never really necessary unless you got banned from a site.
I am on a Windows 8 computer and this is mainly what I want to change the ip for.
There is no logical link to needing a new public IP to being on a windows 8 computer.
Explain more about your problem.

Bridge mode for Airport Express or DSL modem?

I bought a new DSL modem (Netgear Broadband ADSL modem DM111PSP) to replace my old Westell. I also bought the new Aiport Express station (2012 model) to create the WiFI network at home. At the moment, the AE is in Bridge mode so that the DSL modem is on PPPoE to be the one assigning IP's for 3 portable Macs (2 on Wifi and 1 on Powerline->Ethernet). My ISP is AT&T.
I wonder if anyone can answer my following questions:
1) When Apple claims that the AE can support up to 50 concurrent users using the Internet, does that also apply to the AE in Bridge mode?
2) Can my ISP detect the fact that I have 3 computers with the current setup and start charging me more?
3) What will happen if I put the modem in Bridge mode and AE in PPPoE? Can my ISP still track the same info in (2)?
Thank you so much.
My computers (1 MacBook Pro and 2 MacBooks) are all on OS 10.6.8.
Gary

I thought AE cannot assign IP's once in Bridge mode.
That is correct. DHCP and NAT services are turned off when the AirPort Is configured in Bridge Mode.
If both modem and AE assign IP, would that create 'Double NAT' error?
Correct. Either the modem/router has to be in Bridge Mode and the AirPort handles DHCP and NAT.....or.....the modem/router handles DHCP and NAT and the AirPort is set up in Bridge Mode.
There are upsides and downsides to either approach. The simplest setup is to let the modem/router handle DHCP and NAT and configure the AirPort in Bridge Mode.
However, if you were planning to use the Guest Network feature of the new AirPort Express, then the modem/router must be configured in Bridge Mode and and the AirPort handles the DHCP and NAT.

Using Airport Express without a modem

Can you set up a wireless network using Airport Express without a modem? I want set up a wireless network at work. Can I just plug in the ethernet cable on my desk to Airport Express for it to work? Thanks.

Hello Low77. Welcome to the Apple Discussions!
Can you set up a wireless network using Airport Express without a modem?
Yes. By default, the AirPort Express Base Station (AX) will create a stand-alone wireless network which you can connect up to 10 wireless clients for file or printer sharing.
Can I just plug in the ethernet cable on my desk to Airport Express for it to work?
You do not need to plug it into an Ethernet cable for it to work. However, if you require network or Internet access, the Ethernet cable needs to be connected to a network or have Internet access.

Apple airport express not recognised

I have a new iMac running on Yosemite and an old(ish) first gen apple airport express which allows me to stream itunes to my nice big speaker and that works great.
Also have an Apple TV, an iphone and an iPad and they all talk to each other fine.
Have bought another, second hand, first gen (model number A1088) apple airport express as I want to get another nice speaker for another room so I can have music streaming throughout the house.
However, when I plug this second apple airport express in all I get is a flashing amber light and it's not recognised on the airport utility on the mac or on my iphone.
When I disconnect my original apple airport express and leave the 2nd one still connected I "think" my Mac detects it but it says the Airport Utility does not work with this device.
Can anyone please help?
I have power cycled everything (inc modem/router) and no change.
Thanks

Believe it or not I have got it all working.
I ethernet connected the troublesome AE to my router, downloaded AU 5.6 and configured it to join my existing home wifi network.
Yes my iMac's and iPhone's AU won't allow me to change any settings but they both now see it.
If I want to make any changes I just use the AU 5.6 that I now have on my iMac. And any changes I want to make on the AE which I have been successfully using I just use the Yosemite AU.
All good. Now off to go shopping for a nice powered speaker.

Apple Airport Express and PC Laptops - Wireless Network Help

Hello all,
I have two Wi-Fi enabled laptops running Windows XP, an Apple Airport Express unit and a Netgear DG-632 Modem/Router.
At present the DG-632 is running in modem mode and is connected to one laptop using the ethernet connection. The Netgear DG-632 Modem/Router has one ethernet connection and one USB connection.
My understanding is that if i run one laptop off the USB connection on the Modem/Router and connect the the DG-632 to the ethernet connection then the laptop on USB has to be turned on for the second laptop to access the wireless network.
Assuming the above is true (i am very likely wrong), it would be nice if both laptops were able to access the internet wirelessly via the Airpot Express Unit.
However, being a complete novice at networking, i am little confused about how to do this?
Any help, tutorials or advice would be greatly appreciated.
Thanks in advance.

I'm new. I have a Dell Laptop XP and my wife has a
dell desktop XP . I have DSL with a Linksys wireless
router. After many hours on the phone I was able to
get the ineternet set up for me and my wife.
After all this I found that my Airport Express system
couldn't connect to my stereo. It seems that the
router wireless connection pays no attention to
Airport. Apple says that they could set up another
wireless system to work for Itunes by using my
wireless card in the Laptop.
But... I can't listen to the music and surf the net
at the same time. A linksys person has tried to allow
Linksys to accept and proper installation to the
router. I tried is but it didn't work.
Dell Laptop Windows
XP Wireless card and Linksys
router
Dell
Laptop Windows XP Wireless card and
Linksys router
Sort of new here and to the AE, but have a Dell Desktop and Tosbiba laptop both running XPHome SP2, and on dialup
The Linksys router is hooked to the desktop with an ethernet cable. In the office.
The AE is in the living room and works great for surfing and ITunes.
The only way I could get my AE to work as an access point for dialup and stream ITunes from the laptop to the home theater was to use the setup found here.
http://rgbdream.com/?p=44
The only problem I had with the setup was do not use the $ when entering the password. And had to use a proxy server on the desktop for sharing the dialup. LOL no hope of any broadband here.
Hope this is some help.
Bob

Apple Airport Express is not recognized

I bought an Apple Airport Express to help boost and/ or extend my Wi-Fi. Prior to this, I was using a combination modem/ router that my ISP provided. Anyway, I attached an Ethernet cable from my router to the WAN port on the back of my Airport Express. As I understand, it should then appear in Airport Utility, but nothing shows up. The device just blinks amber green. The error message in Airport Utility says, “No Configured Airport Base Stations have been found.” My Internet is otherwise working fine, but Airport Utility fails to recognize it. What could be wrong?

Power up the Express for a few minutes
Hold in the reset button on the Express firmly for 10 seconds
Allow a full minute for the Express to restart
If Mavericks or the iOS devices cannot see the Express, you have a defective Express.
Note....the Express will not "boost" or "extend" the signal from your wireless router wirelessly....unless you have another Apple router.

Apple Airport Express NOT Working! Internet IS working.

I have Apple Airport Express. It is wireless and multiple computers as well as cable are all able to access internet because of this handy device. However I have unplugged it because I was having an issue with Apple TV... and I plugged everything back in and I won't get internet. I called my internet provider and they had me hook up the internet directly to my laptop (skipping the Apple Airport Express) and now I have internet again! However, I only have internet on the one computer that is hooked up... not all the computers/TVs/Apple TVs/iPad in the house.
It isn't an issue with the internet provider because I can get internet. I can't help but think that it is a problem with the Apple Airport Express. I've unplugged everything, waited a few minutes and plugged everything back in. I've done this a few times. Nothing seems to work. What am I doing wrong? I was working fine before the first time I unplugged (and that was due to another Apple device, I think, going wrong).
Help!

Morning zannahdoll,
Thanks for using Apple Support Communities.
Some Internet service providers use a method called "hardware access provisioning" to regulate access to their networks. It normally means that only one of your devices (such as a computer, base station, or router) can connect directly to your modem at any given time.
For more information on this, take a look at this article:
AirPort Base Station: ISP provisioning may prevent Internet connection via broadband (cable or DSL)
http://support.apple.com/kb/ht2460
Hope this helps,
Mario

I Phone 5, not connecting to Apple Airport Express Wifi

I have a dual issue, I have comcast internet and am using a Arris TG862 all in one modem/router. I recently had comast switch the modem to BRIDGE mode so I can use my apple airport express router for WiFi. Now, since it is active and I can connect via my macbook pro, I pad2, etc I cannot connect via I phone 5. What is the issue? Did I set up my airport express incorrectly?
Thank you

Sure...
See this Apple article for a Hard reset of a Factory reset.
http://support.apple.com/kb/HT3728

How can I connect Charter's DOCSIS 3.0 cable internet to Apple Airport Express?

Hey,
Ive recently relocated & had to switch to Charter internet. They provided the wireless router for the time being, however, I would like to use my Apple Airport Express.
Charter says that I need a DOCSIS 3.0 device. I have no clue what that is.
Any help will be highly appreciated.
Thank You

By DOCSIS 3.0 device, Charter is referring to a version of a broadband Internet modem, not your AirPort Express. If Charter is already providing you with a wireless router they may be doing so as a combination modem/router or just a router. If the latter is the case, then you would still require a modem for service.
Regardless, what it make & model of the wireless router that Charter is providing you?

How to use my 3g dongle on my Apple Airport Express?

I have a 3g hspa dongle.I want to know that my dongle can be used with Apple Airport Express utility.I want to connect my dongle into Apple Airport Express utility and share the internet with my ipad,ipod and iphone.I want to know how to do this?

Hi Bob, just wondering if i use a Ethernet USB adapter, connect USB end to the 3G dongle and the ethernet end, with a small ethernet cable to the WAN port of the airport express, is it still possible to use the internet in the dongle through airport express?
Regards,
Vikas

My Apple Airport express loses connection

We have a 3-4 months old Apple airport express. When it works, it works really well.
We use it for streaming shows etc on the television via Apple tv and obviously to go on the internet.
We have 1 iphone 5s and 1 iphone 6, 2 iPad Air, 1 MB Air and 1 MB pro Retina so all our devices are pretty much Apple.
The express router is connected straight to the internet cable from the wall, so there is no router in between or anything. I can always connect with the router, but internet is not always pooring through. In other words, im always logged on the wifi, but it seems as something is often blocking the internet. It definitely has something to do with the router because I can be on the internet via the router on the macbook air while both iPads won't work.
I often solve the problem by opening network preference - assist me - continue - log on the net again - type in my password for the computer and then it works again. But this is obviously not a sustainable solution. And this is also not an option on the iPads, so when it doesnt work on the iPads it just doenst work... :-/
What is the issue?

No one?

Is it possible to create a hot spot with Apple Airport Express 2nd Generation Dual Band Wireless Router, usefull in a hotel with ethernet wall sucket.

is it possible to create a hot spot with apple Airport express 2 generation and use it i a hotel with ethernet wall socket and use it with my Ipad 2?

HenrikAppleJespersen wrote:
is it possible to create a hot spot with apple Airport express 2 generation and use it i a hotel with ethernet wall socket and use it with my Ipad 2?
Yes, it is one of the things AirPort Express was specifically designed for.

Erro 3256 using Apple Airport Express with Windows XP Pro SP2

I am running Windows XP Pro SP2 and am trying to stream my music to the Livng room from my PC in my office. I use an Apple Airport Express. I am running iTunes 8.0.1.11 on the computer that isn't getting the signal through. Now please read the entire message before you decide it is the version of iTunes that I am using.
It was getting through just fine on my Denon 3300 but since I switched to a Denon 3802 the signal is not geting through from my main computer. It works fine from the computer sittng adjacent to it.
I also have music on a 2nd computer and am running iTunes 7.6.2.9 on it. The music gets to the living room stereo just fine using the same Apple Airport Express. The signal strength on the computer that is successful in streaming the music to the Apple Airport Express is "excellent". On the computer that is not successful, the signal strenth is "low". Now these computers are adjacent to each other and the signal has to go through the same wall and
exactly the same distance over the same network.
How can it be "excellent" on one and "low" on the other? Is it just a matter of signal strength? How do I fix that?
I keep getting "unknown error occurred 3256"
Help please. Do I have to do something to the network? or???
Remember I am a Windows user, not a Mac user. I do not have a "Configure IPv6" setting anywhere in my preferences. That must be a Mac thing.

Got the error message 3256 after downloaded latest itunes version 8.xx.
After days of reading logs and bullentin boards, uninstalling, hard resets,firewalls experiments, etc, I found solution for me. Following firmware upgrade to airport express solved. When you go to Apple download center and search for airport revisions only the MAc version pops up. However they do have this one for windows. Give it a try. Good luck.
http://www.apple.com/downloads/macosx/apple/firmware_hardware/airportexpressfirm wareupdate63forwindows.html

Apple Airport Express - Scientific Atlanta Modem

Similar Messages

Maybe you are looking for