Apple DVD PLAYER ERROR

After installing 10.5, opening Dvd player i received this error
There was an initialization error
A valid video device could not be found for playback [-70017]
I've searched all over the forums with no solutions.
i know its not a big problem with leopard but any workarounds would be apprec.
The apple dvd player is version 5.0

now I do not know if this is just me but I have had issues with the DVD player
I played a DVD from a one on the older iDVD software (before iLife 08)
the DVD would work in Tiger fine
I downloaded Leopard, now i get a message if i select "play from beginning of the disk" "skipping over damaged areas"
this also caused the DVD player to not play on my mac and the DVD player locked up
I then tried selecting "begin from last time played and everything worked fine"
the DVD player did not lock up
this is definitely I feel a bug but i wonder if anyone else has had the similar issue
Message was edited by: jcomp
Message was edited by: jcomp

Similar Messages

Apple dvd player / external dvd drive issue

i recently bought a LaCie d2 external dvd drive, since my desktop g4 only has an internal cdr drive. I am running osx 10.4.3, which i installed through this dvd drive. yet now, when i put a DVD movie into the drive and try to open Apple DVD Player, it says
"There was an initialization error. A valid DVD drive could not be found. [-70012]"
i know this is a third party drive, but can anyone help me out? pleeeease?

This is to be expected. DVD Player will only work
with an external DVD drive if the Mac has an internal
DVD drive.
However you may overcome this limitation using PlayerPatc
h.
I had the same problem as above (error code [-70012])... I downloaded this patch for my LG external DVD/RW Model GSA-2166D and it worked perfectly... can now play DVDs...
It's people like you who make being part of the mac community a joy!
Now I just need to find a patch to get the Light Scribe to work...
Thanks!
A1005 Mac OS X (10.3.9) M8758LL/A

Problems playing DVD in Apple DVD player

Hi guys. I am having some trouble with a DL DVD I burned in DVD SP 4.1.0. The DVD plays correctly everywhere (set tops and computers) except when using the Apple DVD player 4.0 (I think that's the version that came with OS 10.3.9.). I have a newer version of the player on my system and everything works fine but when I send the disk out for testing, it comes back with a ton of errors when played on an older version of the Apple DVD player - buttons not working properly, video tracks not followng the end jump, menus not linking, etc.
Is this a known issue between DVD SP 4.1 and Apple DVD player 4.0 (or DL disks and Apple DVD 4.0)? What should I do about this? I've burned DL disks in DVD SP 2.0 before without any problems. I just recently upgraded to 4.1 and now am having this issue. If I maybe use Roxio to burn the disk would that help? Anyone have any experience with this issue? Thanks?

If I maybe use Roxio to burn the disk would that help?
I personally think it would.
I always use Toast to burn discs
Past experience has shown that when DVDSP has burned the discs they often had errors, the same projects burned using Toast produced faultless results
I now author in DVDSP, building the VIDEO_TS folders to the hard drive, then burn these to disc using Toast.

First Play "Not Permitted" on Apple DVD player

I have some duplicated DVD-Rs of a project, and the client ha reported a disutrbing error. I've been told that on several different Macs running OS 10.2 - 10.4, not only does the disc not auto launch DVD player and not auto-play the first play menu, but when the user presses play on the floating control, they get a "Not Permitted" message. The user reported that they were able to choose "open Video_TS" and navigate to the VIDEO_TS folder on the disc, at which point they were able to get the disc to play.
The disc include a significant amount of content on the ROM sector of the disc, including an autorun and an .exe file for windows users. However, I can't see how the presence of these ROM files could interfere with the operation of DVD Player and the VIDEO_TS folder on the disc.
Furthermore, the duplication master for this disc has been formatted directly from DVD studio as a standrd DVD volume - no Toast burn, hybrid volume formatting, anything like that.
Upon inspection I discovered that my authoring assistant had specified a pre-script on the first play menu. I try never to use pre-scripts for anything, as I have found the way DVD studio handles them to be unreliable. However, I suspect this pre-script on the first play menu as the culprit in this problematic behavior, and have removed it.
The problem consists in that I did not experience this problem with any of the DVD-R checkdiscs I burned from DVD studio, unti the discs were duplicated. We'll be doing a full-scale replication run as the next step. Since I am not able to reproduce this problem on discs I burn here, I'd like find a way to know I have fixed the problem.
My question is, has anyone else ever encountered issues with their first-play menu throwing up this "not permitted" condition in Apple DVD Player? Has anyone ever found a connection between this issue and pre-scripts, or between this issue and any ROM files?
I suspect that DVD studio's pre-scripts are "simulated" or translated through the abstratction layer of DVD studio in a way that allows them to be outside the DVD spec, or perhaps there are other ways DVD studio might be using the pre-command on a menu, such as when you specify a button selection for a menu, that use the menu pre-command, and override the pre-script you might have spcified for the menu.

I've seen it on replicated masters when a dvd-r master was used and not all regions were selected as ok to play. DSP doesn't 'check' region 7 by default... its best to use a region all project and .img files, not VIDEO_TS builds to the HD.
How were the discs duplicated though? That is probably the cause of the problem, not the pre-Script. Maybe a 'Data' disc was burnt and not a DVD-Video type option...
-jake

DVD Player error -69902?

I've successfully played DVDs on my iMac (24" 2.4 GHz Aluminum) -- Front Row works like a charm! However, I've recently encountered a DVD that has issues with my computer:
A couple of weeks ago I received the Beatles' "Help!" two-DVD set in timely fashion after ordering it through Amazon.ca. Unfortunately, although the second disc works perfectly on my computer (a 2007 Apple iMac 24" 2.4 GHz Intel Core Duo with 2 GB of RAM), the first disc will not play past the FBI warning and the opening page (where Play, Subtitles, Settings, Chapters is located). Whether I use either Front Row or DVD player, the result is the same: when I insert the disc into my computer, I am presented with the error message "Skipping Over Damaged Area". If, in DVD Player, I click on "Title" in order to change chapters, an error message pops up informing me "DVD Player encountered a system error. Error -69902". And in DVD Player, I am informed that this disc contains only one chapter. In any case, when I'm on the Help! opening page & I click on "Play" (in either DVD player or Front Row), nothing happens. No movie. The music keeps looping on the opening page, but not much more than that.
Out of curiosity, I tried playing this same disc on a standalone Toshiba DVD player hooked up to my home TV, and amazingly, the disc plays fine!
After emailing Amazon, I was instructed to return the DVD for a replacement, which arrived in the mail today. Imagine my surprise when the replacement displayed the same error messages! Before I return this disc for a refund, maybe someone can fill me in: what is DVD Player error -69902?
Message was edited by: Captain Maniac

Faulty disc

Having trouble with apple DVD player playing Mpeg-2 file

I have this error on my ibook when i try to play an mpeg-2 file recently created through HD - Export/Using quicktime conversion.
The error from Apple DVD player is Dvd Player encountered a system error. could not detect a valid media file. [-70001]
Is there something Iam doing to this when i cut it? I have the same problem on both my laptop exppress harddrive, desktop express version 2.
Is tere a different way I should do this?
Thanks

Hello Richard,
That error code suggests that the region code has been changed 5 times. You can only change the region 5 times in iDVD.
Have a look in here
for some alternate players. There are some really good ones.
I hope that helps some.
Regards
Ian

MacBook DVD player error scratched CD

I bought a DVD film and while watching halfway through the show the player stopped and reported an error. CD may be scratched, it said. I returned the dvd where I bought it from, and purchased the same movie from another source.
Same problem. In between these I watched several movies and this problem only happened twice. Restarted the MacBook and it continued from where it stoped. But NOT with the movie I replaced.
Any suggestion? No, no, no, I got rid of all of my VCR's and the players too.
By the way it is a Roger Moore movie named GOLD. Beware :-))
I would like to finish it one day.

Version 2.7 of the DVD Player appears to be the correct version for your configuration; any computer which can use the 2.0 beta which came with some 8.6 versions can use version 2.7. No iMac is compatible with version 1.x of the Apple DVD Player.
(16418)

Why won't DVD play on Apple DVD player?

I put a DVD of a TV show into my MacBook but it won't play. The DVD was made in 2005 and has played in the past, although I haven't tried to play it in years. How can I make the DVD play? The error message I get in the Apple DVD player is "Supported disk not available"

VLC Player... it will play just about any format under the sun.
http://www.videolan.org/vlc/index.html
If you can't get it to play from the disc directly, try copying the entire contents to the desktop and trying to run it from there. If it refuses to copy the disc, it usually means the disc is not readable. Could be dirty or damaged.

Apple DVD player / region code

I apologize if this is the incorrect forum for this question, but I could not find a forum specific to the Apple DVD player.
Several months ago my internal DVD drive died and I replaced with an external LaCie firewire drive which I purchased from Apple. Until today all I have used it for is burning disks, and for that it has worked flawlessly. Today, however, I needed to use it to view a DVD. When I inserted the DVD i got a pop-up box which stated "Since this is the first use of a DVD disc, the drive region must be initialized before playing." A drop-down box gives me the options of regions 1-6, and 8. When selecting region 1, or any region for that matter, I get an error message which states "There was a problem changing the drive region code," and it gives me an error code of 10007. If I click Cancel the disk ejects and Apple DVD player pops up. Thinking there might be a problem with this disc I have tried several dvd movies. I do not get the pop-up box with the region code choices, instead Apple DVD player pops up, but the movie will not play. On screen it says "Supported Disc not available."
I tried the original disk in my G4 PowerBook and it plays fine.
Any help would be greatly appreciated.

The LaCie drivers haven't changed since 2008 or before. Traditionally, computer DVD drives ignore region codes (a region code is a feature which should be illegal, IMO). So, unless your computer is new, I'm guessing the region code block is programmed into 'DVD Player'.
I've a LaCie external DVD drive, and I found the free MPlayer produces a much better image than 'DVD Player'. Haven't tried VLC in several years, but it's considered my many the best.
MPlayer
http://www.macupdate.com/info.php/id/18580/mplayer
VLC
http://www.macupdate.com/info.php/id/5758/vlc-media-player
Be sure the external drive is being accessed. (You might want to stock up on such software while that for Tiger is still available.)

Apple DVD Player & Pioneer DVR-112D problem

Hi,
I am not sure in which section I should post this question, so please forgive me.
I have an *iMac G4 700MHz Flat Panel* (without DVD drive) running Mac OS x 10.2.8.
I have recently purchased from macsales.com an OWC Value Line Dual Layer DVD-/+RW
*Pioneer DVR-112D 18X External optical drive*, and, following their instructions, I've installed PatchBurn 1.1b on my iMac. Unfortunately, when I am trying to play anything on my Apple DVD Player I keep recieving a message informing me about some error and saying that proper driver hasn't been installed. After that, DVD Player shuts down.
When I look at the diagram in Apple System Profiler (Devices and Volumes) I can see my new Pioneer drive either in USB Information section (when I connect it with my iMac via USB port) or FireWire Information section (connected via FireWire port), and the Pioneer drive is reported as a fully supported one. I never get my Pioneer drive shown in Bus section of the diagram (as it is shown on their website), but I guess it is OK, since it is an external drive.
What could be the cause of my problems with playing DVDs?
Do you think that it is a driver problem or application problem? Apple DVD Player hasn't been used before since I have not had any DVD drive on my iMac.
Any help will be appreciated.
Abadon
Message was edited by: Abadon
Message was edited by: Abadon

iDVD6 & iMovie mandate a firewire connection (not usb).
In terms of the drivers, you'll have to contact the vendor to get more info should any drivers be required via firewire.
My own ext. FireWire Burner doesn't require any 3rd party drivers whatsoever. But this may vary from vendor to vendor and from drive to drive.

Menu buttons not working in Apple DVD Player

I am having a real problem. I have a menu with three buttons. The default button takes you either of the other buttons (depending on whether you press right or down on the remote). These two buttons are auto-action and proceed imediately to other tracks. This works perfectly in home DVD players and in the Apple DVD Player using the "remote". Howver, if I try clicking the buttons using a mouse on the Apple DVD Player window, they DO NOT work! I have buttns over video on the same disc and these work perfectly by clicing on them with the mouse. Has anyone else had a problem like this and if so, have you found a solution? Many thanks!

Is the one that doesn't work a layered menu? DVD Player does not work correctly with layered menus, it takes one click to switch to the selected state, and a second click to activate the button.

Apple DVD Player installers won't recognize Lacie d2 16x4x12x

Greetings :
My eMac has a CDR internal drive only.
I just upgraded to Panther (upgrade disks) and I'm running 10.3.9.
I'm trying to get the Apple installers to recognize the Lacie d2 I just got, so that I can install the Apple DVD player (software update?) or import a DVD player from another machine.
The software won't install because it says it can't detect a proper drive, and the player I imported won't open for the same reason. I tried using Patchburn, Pacifist and the installed Installer on my eMac to no avail.
Here's what my system profiler says about the d2 : : :
FireWire Bus:
Speed: 400 Mb/sec Speed
LaCie 1394 DVD-R/RW+CD drive LUN 0:
Manufacturer: LaCie Group SA
Model: > LaCie 1394 DVD-R/RW+CD drive LUN 0
Drive Type: CD-RW/DVD-RW
Disc Burning: Vendor Supported
Removable Media: Yes
Detachable Drive: Yes
Speed: 400 Mb/sec Speed
Unit Spec Id: 24734
Unit Software Version: 10483
Firmware Revision: 2.07
I believe the Lacie d2 I just got is the previous generation,
no lightscribe. It works great (plug an play) for burning data but I'd really like to use the native Apple DVD player to watch DVD video with the drive. I downloaded the free/open source VLC media player and it seems to work well enough,
but I'm on a mission to use Apple software if possible.
I'm also thinking of upgrading to Tiger soon so I'm wondering if I'll have any corresponding issues there.
Oh, and I did download and install the latest driver was from the Lacie site.
Any suggestions would be greatly appreciated.
pauly B ;D
eMac Mac OS X (10.3.9) 700 MHz / 384 MB / 40gig / CDR internal

BTW: here is the fix in case anyone needs it
Follow it exactly, it works !
1. Download and install Pacifist.
2. Insert Mac OS 10.3 CD in drive.
3. Select Open Mac OS X Install Packages button in Pacifist. It will ask you to swap out all three 10.3 install disks.
4. Click the Find button and type "DVD". A long list should show up.
5. The important files/folders to replace are:
-AppleAltiVecDVDDriver.bundle
-ATIRadeon8500DVDDriver (if graphics card is installed)
-ATIRadeon9700DVDDriver (if graphics card is installed)
-ATIRadeonDVDDriver.bundle
-ATIRage128DVDDriver.bundle (if graphics card is installed)
-DVDPlayback.framework
-DVD.framework
-rtadvd
**There are many duplicates of the files/folders above in other languages. I only chose to install English.
6. Select each or all and click Install.
7. Choose to replace all existing files.
8. Restart. Repair permissions.
I didn't bother to try to install only the English versions...just installed and replaced all the items on tha list
;D

Clock freezes after using Apple DVD Player

I am having a small and annoying issue with the Apple DVD Player (v 4.6.5). This just started happening recently. Everytime I run a DVD (or video TS file, etc) on the software player-it performs as usual. After quitting the application and choosing to eject the disc, I notice there is a longer lag from when I first used the computer, then the little colored wheel of death spins, and eventually Apple DVD Player closes.
The problem, however, is after the application is closed out, my time freezes in the status bar in the upper right hand corner of the screen. (As I write this it says 1:16 and the time in the apple "date and time" preferences panel of OSX says it's 2:14-which is the real time) If I drag the cursor up to the time status bar in the upper right hand corner, it turns into the spinning color wheel, and back again once dragged out.
Once the computer restarts, the time in the upper right goes back to normal with no spinning wheel (until I open Apple DVD Player and quit out of it again). I know this is not an earth-shattering issue, but it is fairly annoying and abnormal. If anyone has suggestions, please help.

It sounds like you found your answer but I also wanted to mention that this is a known BUG when using DVD Player and the Digital Optical Out of a G5. If you look at activity monitor when the Clock is dead and you get the Beach Ball the SystemUIServer will be listed as not responding. If you Force quit this process everything should start working again. As long as the LoginWindow Process is running the SystemUIServer will restart when needed after the force quit.
HOWEVER, The other part of this bug with Digital Optical Out is that sometimes the LoginWindow Process will also stop responding. In this case a Log-Out is the only way to correct the problem. The third part of this bug is sometimes the Finder also stops responding but a Relaunch will fix that.
As I said it sounds like you found your problem but I wanted to post this incase others out there using the Digital Optical Out read this and don't correct their problem.
Also, If you were using the "DOO" by deleting the .plist will set the DVD player back to SYSTEM falsely making one think the problem is fixed.
Last I know this is a known bug because I submitted it as a bug to Apple and received an e-mail stating they know of this problem already.

I have a G4 and Apple dvd player cannot find software it needs

i have a G4 with 10.5 I am getting a Apple dvd player cannot find software it needs, how do i reinstall it thanks

I solved this by reset of the Wifi (unplug cable and power to both modem and wifi ... wait 60 sec ... plug in modem cable and power ... plug in wifi power and LAN to modem ... restart AppleTV and Mac ... Turn Home Share 'OFF' in iTunes then back "ON" ... it took ~60 sec for the AppleTV to pick up my Mac in computers.

Scripts works in Simulator and Apple DVD player but not on TV

I have a basic project with two different tracks.
The first one is video and audio. Plays "as is".
The second has video, two audio and one subtitle. Depending on which button, the second Track should be played with different audio and with/without subtitles.
(I use GPRM 1 to set the subs stream, GPRM 2 for the audio and GPRM 3 for menu button navigation).
On the second Track I have a pre-script that sets the streams depending on the value of GPRM 1 and 2.
Works fine in Simulator and in Apple DVD player, but not on the stand-alone player.
Any idea what might be the issue here?
in short:
Button 1: Play Track 1 "as is" (audio 1, no subs)
Button 2: Play Track 2, audio 1, subs on
Button 3: Play Track 2, audio 2, subs off
Button 4: Play Track 2, "as is" (audio 1, subs off)
Menu button and End Jump should go to the corresponding menu button.
Many thanks for your help.

It is part personal preference, part artistic, part what makes the user experience the best so there may not be one "right" answer and I have often made menus one way than changed them when viewing the DVD for something that seemed to work better.
Looking at you description I started playing with some ideas in my head and started typing them, then changed what I was writing
It sounds like you want chapter selections for both track 1 and track 2? If so it may make sense to have the initial menu have Track 1 and Track 2 buttons which then link to sub menus where there is "Play All," selections for each section of each movie and one last button for the preferences.
Alternatively you could also place the preferences selection button on the main menu, though since Track 1 does not sound like it really has preferences you need to make sure that users do not become confused and think they have turned something on/off and are not seeing these options when they thought they selected them when they play back Track 1.
Also with 6 to 8 chapter markers you may be getting close to the point where scripting could make it easier if your selections are just to play the sections - in other words for track 2 four stories take care of the combinations Audio 1/Sub Off, Audio 1 Subs On, Audio 2 Subs Off, Audio 2 Sub On. If the chapter selection starts the track a scene then plays through you can target chapter markers in the story so 4 stories takes care of it. If you are just playing sections you would need 4 x 6 or 8 chapters - 24 or 32 stories roughly. But it is actually fairly quick to do - just set up the intial Play All with all subtitles and audio selections unchecked except for "1" then copy from there. Probably should take under 10-15 minutes or so
Put a real quick thing together for a quick view of the tracks. I can flesh it out more if you like.
http://www.dvdstepbystep.com/081107Sub.dmg
The main menu will be the title menu, then the sub-menus (including the set up menus) can be placed in the same VTS as the applicable tracks which can help a bit with DVD performance speed. Since there is 6 to 8 chapter markers on a track each of the main sub-menus would have 8-10 buttons which can work in the design.

Apple DVD PLAYER ERROR

Similar Messages

Maybe you are looking for