Apple logo appears only and cant restore in recovery mode
iphone4 wont work tried everything. the only thing that it shows is the appl logo and whe i put it into recovery mode it wont let me restore or update
Put the Phone in DFU and then try to restore
Step 1. Turn off your iPhone.
Step 2. Hold down the power and home button.
Step 3. When you see the Apple logo, release the power button but continue holding the home button down.
Step 4. Open iTunes and wait for it to tell you that its in restore mode.
Alternative Method:
Step 1. Connect iphone to USB then listen to the sound when it connect and disconnect.
Step 2. Hold the home and power buttons until hear the disconnect sound then release power button.
Step 3. Wait until you hear another sound then release home button.
Similar Messages
-
My iphone 4 stuck on the apple logo then it wont work in recovery mode. My iphone then wouldnt work in recovery mode, itunes said there is something wrong with my iphone. On my iphone it says connected to itunes any ideas what could be wrong
You might have to get it serviced, or visit an Apple Store to get it looked at.
Apple - Support - Service Answer Center -
Cant restore from recovery mode iphone 4s
Can't restore iphoe 4s from recovery mode. Error 21 happing every time.
Check for hardware issues
Related errors: 1, 3, 10-47, 1002, 1011, 1012, 1014, 1000-1020, 1669.
Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good. Also, confirm your security software and settings are allowing communication between your device and update servers. If you still see the error message when you update or restore, contact Apple support. -
Please help!
Nobody here can help you. Discussing jailbreaking is a violation of the forum terms of service. Go to the website that told you how to jailbreak and get the information you need there.
-
IPod 1st Generation Touch- System Restore from Recovery Mode
My iPod Touch 1st Generation worked fine one day and the next day all it would do is disply the little white "Apple" and then go black. It was fully powered. I opened my Itunes account and connected the iPod. Nothing. Then I saw on a previous discussion board to hold the power and home button at the same time while hook to my computer. A graphic of the usb cord and Itunes appeared, and the Itunes account recognized the device but said it was in "Recovery Mode" and in order to have it work again I would need to allow for a system restore. So I did. It seemed to go through the process and then tried to re-sync. It has now been "syncing" for over an hour. It is stuck. I can not do anything, even if I disconnect the iPod from the computer. I have no idea what to do, I am super frusterated. My iTunes account seems to be locked and have not made any progress with the iPod of getting past any other graphic other grapic besides the usb/iTunes picture. Please help if possible.
Also, since it is a 1st generation, I recently upgrade the OS to the only allow upgade however, I am not sure which one it was. This is the first problem I have had with my iPod. Apologize for the lack of specifics.
Thanks much in advance.Close iTunes and disconnect the iPod from the computer. Reboot the computer. Then try to restore again.
- Try as necessary:
- A reset.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Placing the iPod in
Recovery mode
- Placing the iPod in DFU mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- Both those modes require that you turn the iPod fully off. If you can't do that let the battery fully drain. After charging for at least an hour try the reset.and restore again.
- If still not successful time for an appointment a the Genius Bar of an Apple store. -
Having resent my iPad using the Settings route, the Apple logo appeared onscreen and a line below it filled from left to right. When full, the device did nothing. I was able to switch it off and back on, only to see the same Apple logo and filled line. Even pressing the ON botton for a few seconds did nothing. The device is now inert, and I cannot access it. Please help!!!
Reset iPad and continue with Restore.
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected. -
Header 1
Header 2
iPhone 4 screen remains blank and only the apple logo appears on and off when connected to mains or PC. Only on mains occasionaly proceeds to display IOS 6 logo and a slide sign to start recovery which proceeds to an instruction to connect to iTunes. Hwever, as soon as disconnected from mains (in order to connect to the PC) screen goes totally blank again. On connecting to PC the Apple LOGO starts appearing intermittently but does not proceed to display IOS 6 LOGO. I have recharged overnight and followed resetting instructions as per the iPhone support page. Any suggestions (short of taking it to a service centre) ?did you get any help regarding the problem?? because even i have the same problem!!! guess it all started after updating to iOs 6
-
please help i upgraded my iphone5 to new ios7 yesterday 2pm and untill now its already 17hours and why cant access or back to normal?is this normal or stil upgrading? it only appears the apple logo on screen and keep coming the logo screen on and off.do i need to bring my phone to apple center or is this iops 7 takes longer time or an hours to successfully upgraded.please help me what can i do?
Anyone have any suggestions? or is everyone else just as clueless as me !
-
I am trying to figure out why I cannot restore my Ipod touch 64, when I get through the whole restore it states "error code 1602". I have used the original cable that came with the Ipod and have tried it on two different computers. When I turn it on only the apple logo appears and nothing else happens. Please help
Error 2000-2009 (2001, 2002, 2005, 2006, 2009, and so on)
If you experience this issue on a Mac, disconnect third-party devices, hubs, spare cables, displays, reset the SMC, and then try to restore. If you are using a Windows computer, remove all USB devices and spare cables other than your keyboard, mouse, and the device, restart the computer, and try to restore. If that does not resolve the issue, try the USB issue-resolution steps and articles listed for Error 1604 above. If the issue persists, it may be related to conflicting security software.
If the phone is stuck on the Apple logo, you can try a hard reset (deletes no info). Press and hold the power button and Home button until the phone turns off. Then try to power it up again.
Simply restarting your computer will not cause your iPhone to stop working unless there is a major issue with software conflicts on your computer... i.e.... corrupt iTunes installation.
Try disabling any security software you might have and avoid using and USB hubs or extenders etc.
If the hard reset doesn't work in getting your phone to boot up, then you'll have to do a restore of the device. -
my ipad does not start or reset even. when i hold both buttons only apple logo appears and ipad wont start. plz help somebody
try restoring see guide
http://www.ipadforums.net/ipad-help/2987-how-put-your-ipad-into-recovery-mode.ht ml -
I updated my ios and now only apple logo appears nothing else works
Recently I got a notification about software update and i used itunes to update my ios 5.0.1 to ios 6 but now only apple logo appaers and nothing else works please help!!!!
Try resetting first.
Hold the On/Off Sleep/Wake button and the Home button down at the same time for at least ten seconds, until the Apple logo appears.
If that doesn't help, try restoring your iPhone to factory settings > http://www.everythingicafe.com/how-to-restore-iphone-to-factory-settings-without -itunes/2011/12/13/
Be aware, resetting to factory settings deletes all user data.
Then try updating to iOS 6 again. -
I clicked on "Erase all Content and Settings and now my ipad is not working, only the apple logo appears. how to i reset it back?
Some please show me how to reset it.Here is some information from Apple:
http://support.apple.com/kb/TS3274
http://support.apple.com/kb/HT4057 -
When this happened the first time, I seriously thought it wouldn't come back on. I was trying to crop something out of the of a photo and it shut off like it was dying (it was fully charged) and then froze, turned white, then an apple logo appeared. Once it turned on i went back to do what i was doing and it did it again. The next time it turned on, I went to play Design this Home, and it didnt shut off..so my only reasoning is that this happens when i edit a photo...i haven't done anything abnormal with my iPod and don't understand why this is happening...please please help!
That is a known bug in iOS 5.1.1. The iPod "crashes" when editing photos. Just do not edit photos and wait for the next update. Most users have said it crashes when editing screen shots.
-
i have erased my all phone contact list and then the message comes that it will be deleted with in an hour. but now my phone is not starting and only the apple logo appears on the screen. what should i do now..!
That number is for an apple server in the UK that is used for iMessage activation. A hidden SMS is snet to that number when you turn iMessage on and is used to verify your phone number. I suggest you turn iMessage off. In settings/phone turn on dial assist. Check with your carrier to see if you can send an international SMS as you end that possibility to activate iMessage. Rest your phone (Hold down the Sleep/Wake button and the home button together until the apple logo appears (ignore the ON/OFF slider) then let both buttons go and wait for device to restart (no data will be lost).) then turn iMessage back on.
-
My Nano shuts off in the middle of playing music/podcasts. It won´ respond until plugged in, then apple logo appears and it restarts. I restored factory settings and installed the newest OS which worked for a week, but it´s the same problem today. It happens while at 50% power or better (according to battery icon).
It sounds like the battery itself is going bad, which is likely given the age of the 4G Nanos. You'll want to have your iPod serviced by Apple or a third party service center to have them swap the battery out. Otherwise, it's time to start investing in a new iPod.
B-rock
Maybe you are looking for
-
Display a PDF file from local drive
Hi, I would like to display a pdf file that is actually stored on the portal server hard drive. What I have tried to do is link an iFrame element to the url of the file: "D: MyFolder myFile.pdf" But it doesn't work. I have the following error when tr
-
Response Group to PSTN Outbound Caller ID
Hi Guys, I'm trying to implement an after hours paging service on our lync system using a response group (with overflow set to 0), but the problem I'm currently facing is that the outbound calling number ID is set to the number of the caller, which I
-
Many problems with migration OBIEE
Hi, I upgrade muy proyect obiee 10.2 to 11.1.1.5 and some dashboard displays errors. Some dashboard error says: State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 43113] Message returned
-
Image quality after opening from camera RAW
Why does the image quality seem to get worse in Elements 11 once the image is opened up after editing from Camera RAW? The image looks great in the RAW screen, then once opened in Photo editor it seems pixelated, smooth lines look jagged. Is it som
-
Discussion: The usage of Inspection Points
Hi Experts, Talking about the INSPECTION POINTS, what kind of usage could it be ? In some occasions, it can be used as an sign that distinguish each delivery from the production line to the QM dept. How about any other way to use it?