Apple logo is it a light ?

if it is how do i turn it on it looks like a light :P

The Apple logo below the LCD screen on the iMac does not light up. However, it is where the Infrared Sensor for the Remote Control is located on those models equipped with built-in IR. A few folks with the new 24" inch models have reported that they can occasionally see an LED shining from behind the Apple logo on the logic board.

Similar Messages

  • HT1551 my apple tv is only showing apple logo and the white light keeps flashing what do i do

    my apple tv is only showing apple logo and the white light keep on flashing can anyone help

    You have to restore the device using iTunes
    Apple TV (2nd generation): Restoring your Apple TV
    support.apple.com/kb/HT4367
    You need a micro-usb cable and the ATV must be in DFU mode (Hold down the menu and play button for 7secs)
    Apple TV (1st generation): How to perform a factory restore
    support.apple.com/kb/HT3199 

  • Hi, My Apple TV 1st generation is showing the apple logo and the amber light keeps blinking, after a while it shows a little Apple TV with a question mark blinking on top, any ideas?

    Well my question says it all.  I wasn´t using the apple tv, but noticed that the amber light started to blink, so I put it on the tv and there was the apple logo.  I did the recory with the "MENU" + "-" button, but came back the same.  After a while it showed a little Apple TV image with a "?" mark blinking on top.  I disconected it the whole night but today is doing the same. Is like it got stuck on the restart. Can anyone help me?

    Fixed it after trying everything listed here with no success.
    First you will need to make sure you have the ability to connect your ATV box directly to your router via a cable.  This issue is directly related to networking from my experience and once connected to wifi you will have a nightmare of a time to complete the fix.
    1.  Make sure you have NO network connection to the ATV box.
    2.  Hard reboot ATV using remote (aim remote at device and hold "menu" and "down/minus" until amber light blinks)
    3.  When ATV reboots to a diagnostic menu select "Factory Restore"
    4.  After Restore has completed select a language
    5.  You cannot skip the the wifi selection screen without setting up a connection, however: DO NOT SETUP WIFI!  Instead plug in the direct cable to your router, and hit the menu button on your remote.  You will see "connecting to network."
    6  Once you are past the start up splash video you will eventually arrive at the connect to itunes screen which will start looping the apple logo and a new code about every 2 seconds.  Disconnect the network cable.
    7.  After a few seconds the loop will stop.  Press the menu button to skip the itunes connection (you will be able to do it later.)
    8.  At the following menu go to Settings > Screen Saver > Set delay for "Never"
    9.  Go back to the main menu, then go to Settings > Network > Configure TCP/IP > Click on "Using DHCP"
    9.  Click "Done"
    10.  Connect cable to router, and then proceed with updating your ATV.
    After I was updated the problem did not return.
    I have completed this solution personally twice on the same unit.  After getting updated and stable, I recovered my ATV again, and had the same problems again.  Repeated these steps and good to go.
    Hope this helps someone, and good luck!

  • Apple logo seems to allow light to pass through it onto the display

    Whenever the screen is on low light, or when the backlight is off completely, I can see a yellowy light in centre of the screen which appears to be the apple logo allowing light through. As you can probably guess this is very annoying, is there any way to fix it?

    +*Call Apple tech support.*+
    +*If you want to fix yourself, see if there is a solution on one of the following sites:*+
    iFixit
    TakeItApart
    +*Search YouTube for Macbook Pro “How To” tutorials.*+
    Really?
    Scrobby... the Apple logo is just a cut out in the aluminum casing with a plastic insert that allows the displays backlight to shine through. Unfortunately, it will work in both directions... particularly if there is a bright light shining through the back. You can simply tape something over the logo that doesn't let light through... or put some type of skin or hard cover on (other than a transparent one). You just need to block the light from shining through the back.

  • My iphone 5 suddenly wont fully boot...it stuck on the apple logo and goes of after 20 -25 secs and comes on by itself after a minute or two but still stuck on apple logo..also i am able to see a bit of lighting on the dark screen whenever it goes of

    my iphone 5 on the ios 7.1.2 suddenly wont fully turn on...it gets stuck on the apple logo and stays like that for approximately to 90 secs then goes blank but I can see a bit of lighting  behind the dark screen....it goes off by itself and comes on by itself trying to boot but still gets stuck on the apple logo after the dim light shows....when I connect to iTunes my phone can only be recognised only in recovery mode thus if I force it into recovery mode. My main worry is I don't have a back up of any of my data...on icloud I have just less than 2GB of my data which is as a result of incomplete back up...HOW CAN I GET THIS PHONE WORKING AGAIN WITHOUT LOSING MY DATA...if I can only just recover my data I would really appreciate it as I really  need almost everything on it back...if I can only get retrieve my data and lose the phone I wouldn't mind at all....Anybody know how to resolve this??Kind Regards

    Anyone have any suggestions? or is everyone else just as clueless as me !

  • IPod sticks on Apple logo screen, then turns off

    Hey everyone.
    This just began happening about 30 minutes ago. After un-plugging my iPod (I think i did everyhting right, I followed all of the procedures), my iPod showed the black screen with the Apple logo on it. Ever since then, the iPod has been making a clicking noise and the black screen with the Apple logo on it will light up for about 10 seconds, the light will go off, the ipod will turn off for a second or so, and then repeat this process.
    Thanks alot.
    P.S.- I have already tried the 5 R's. I have tried hooking up my iPod the the cable that charges it and my computer wont even notice that the iPod is attached. I have also let the battery run out, and then recharging my Ipod and trying again, the same thing happens.

    After trying every other opetion, with no success, I went to Best Buy and got a new one (thank god for warranties.)
    They informed me that it was a dead hard drive. If this problem is still happening for anyone, the best thing to do is to take it to the store you bought it from and, as long as you have a warranty, they will issue you a new iPod.

  • Apple logo on MacBook

    A quick (easy) question. Does the Apple logo on the MacBook light up like on the MacBook Pros? Does it stay lit up? Just to clarify, when I say the Apple logo I mean the one on the backside of the LCD.

    Unfortunately, when I put the MacBook sticker on my
    car, it started to overheat, and the bumpers turned
    yellow
    ROTFL/___sbsstatic___/migration-images/migration-img-not-avail.png/___sbsstatic_ __/migration-images/migration-img-not-avail.png/___sbsstatic___/migration-images /migration-img-not-avail.png/___sbsstatic___/migration-images/migration-img-not- avail.png/___sbsstatic___/migration-images/migration-img-not-avail.png/___sbssta tic___/migration-images/migration-img-not-avail.png/___sbsstatic___/migration-im ages/migration-img-not-avail.png/___sbsstatic___/migration-images/migration-img- not-avail.png/___sbsstatic___/migration-images/migration-img-not-avail.png/___sb sstatic___/migration-images/migration-img-not-avail.png/___sbsstatic___/migratio n-images/migration-img-not-avail.png/___sbsstatic___/migration-images/migration- img-not-avail.png/___sbsstatic___/migration-images/migration-img-not-avail.png/_ __sbsstatic___/migration-images/migration-img-not-avail.png/___sbsstatic___/migr ation-images/migration-img-not-avail.png/___sbsstatic___/migration-images/migrat ion-img-not-avail.png/___sbsstatic___/migration-images/migration-img-not-avail.p ng/___sbsstatic___/migration-images/migration-img-not-avail.png Pure class humor. Still laughing/___sbsstatic___/migration-images/migration-img-not-avail.png

  • Why won't my bright Apple logo turn off?

    All recovered on its own now, but I want to know what to do if it happens again.
    Had just completed online application for $100 credit and was receiving the text message with the code when my iPhone froze. All attempts to reset failed. The Apple logo, with a back light, refused to go away. Tech support tried solutions, but all failed.
    Made an appointment with neighborhood Genius Bar. Kept it in charger all night per tech support's suggestion. When I unplugged it in the morning, the first sign of life was a low battery alert. Plugged it in again, started to charge, and all came back.
    But, I was iPhoneless for 12 hours, and what would have happened if there was an emergency?
    Has anyone encountered the same freeze: a bright Apple logo that refuses to go away?
    Thanks!

    A runaway process is preventing sleep and delaying shutdown. Need to use Activity Monitor to identify the miscreant.  http://support.apple.com/kb/TS1473

  • Apple logo came on faded ipad2

    my apple logo came on very light on ipad2 when hold down on and sleeping button

    http://support.apple.com/kb/TS3694#error3014
    This error occurs when iTunes is unable to reach gs.apple.com in a timely fashion. Follow the steps below inUnable to contact the iOS software update server gs.apple.com.

  • Nano won't reset, Apple logo appears and disappears, Nano won't mount!

    My battery died on my 1G Nano sometime last night or the night before. I went to try to wake it up today, and nothing happened ... would not wake up.
    I connected the Nano to the Dock connector which was directly connected to my 24" iMac. The Nano tried to restart, but would not re-start completely, most likely because the battery was completely dead.
    I tried re-setting by toggling on and off the Hold switch and then pressing the Menu and Select buttons, but that did not work. I also tried plugging the Nano into an external USB charger (for regular iPod) and resetting. I still can not get it to reset.
    The Apple logo appears on the screen for a second, the screen lights up for a second, then the screen goes dark again and the Apple logo re-appears and the process starts all over again.
    This has been going on for over 20 minutes. Apple logo will appear, screen lights up, screen goes dark, Apple logo re-appears, etc, etc, etc, etc. Do you see a pattern emerging here?
    Please help!
    Thanks

    When my iphone cracked out, I plugged it in. If it is still discovered in itunes, on the left side bar you should see you device's name. If you click it, near the top it will show your device and have options for backup or just plain restore (which I might recommend here). And if this works awesome! If not, RIP iPhone

  • My iphone 6plus not working not charge but when i run it the first time working half an hour  when you attempt to run it again light up thr screen and showws the apple logo and after the pice screen illuminates red and does not work what do i do now

    My iphone 6plus not working not charge but when i run it the first time working half an hour  when you attempt to run it again light up thr screen and showws the apple logo and after the pice screen illuminates red and does not work what do i do now

    Hello Nadersalah,
    It seems you're experiencing multiple issue with your iPhone. Based on the information you have provided, it appears your iPhone needs to be serviced. The following link should help you get started with the process and has links with additional information on topics such as warranty and service pricing, battery replacement, and express replacement service.
    iPhone Repair and Service - Apple Support
    Thank you for contributing to Apple Support Communities.
    Cheers,
    Bobby_D

  • HT1551 led light continuously flickers apple logo appears then no signal indicator   appears , how can I get back original  setting?

    Having trouble ,tried giving update and now the led light turns on and off continuosly  apple logo appears for a few seconds then the no signal indicator can someone how I can return the unit to its original settings?

    You will need to grab a micro usb cable and restore in iTunes
    http://support.apple.com/kb/ht4367

  • Help! Light gray magnified apple logo then goes black and dies.

    Hi,
    Whenever I start up my macbook pro a lighter than usual gray screen pops up with a magnified apple logo and spinning wheel, it then proceeds to go to a black screen and stays there. I tried starting it up in single user mode and running fsck but that didn't do anything it failed to notice that there was a problem. I then tried running disk aide from my start up disk but it failed to find anything wrong with my computer. I replaced my hard drive with a new one and retried all of those things and still the gray screen would appear. I also ran disk utility and and verified and repaired disk permissions and nothing worked. In addition to that i tried resetting my ram. I have no clue how to fix this I've searched all over the web but can't find anything. I desperately need my computer for school.
    Thanks
    Dave

    WELCOME!http://i29.tinypic.com/2ef7yfn.gif!
    See Article: http://support.apple.com/kb/TS2377 MacBook Pro: Distorted video or no video issues

  • Ipad 2 screen randomly gone blank shows dark blue light up but no apple logo upon restart and remains the same.

    Hey
    So I left my Ipad 2 on charge and it was working absolutely fine. Later on when I came in the room to check up on it, it had a blank screen and the Ipad was lit in the background as it was giving off the dark blue light but nothing on the screen would come up. I tried shutting it down using the power button and the home button yet nothing. Even the Apple logo would not appear. I just recently upgraded to IOS 6. I'm not sure what exactly caused this as it was working fine just a few hours ago. I've tried connecting to itunes held down the power and home button nothing seems to be working. Also I no longer have the warrenty.
    Not sure what to do now

    Perform a Reset... Try again...
    Reset  ( No Data will be Lost )
    Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
    http://support.apple.com/kb/ht1430
    If no joy... Try a Restore...
    1: Connect the device to your computer and open iTunes.
    2: If the device appears in iTunes, select and click Restore on the Summary pane.
    3: If the device doesn't appear in iTunes, try using the steps in this article to force the device into recovery mode.

  • Why did apple ditch the light up apple logo

    the light up apple logo is on the apple stores, all apple laptops and has been in apple commercials dedicated to the stickers that hi light on the light up apple logo but now with the new macbook there is no light just a cold hard metal dark and unexciting.

    My understanding is that Apple does not require payment when their products are used in shows. That would be the opposite of advertising. Normally, product placement works the other way around: the show is paid, not the advertiser. If the Apple logo is hidden in a show, it is usually because the producers do not wish to appear that they are endorsing any particular product. Unlike other products used on set, the Apple logo is so prominent that it is a challenge to genericize without covering it up.
    Most of the reasoning in this thread doesn't make sense. It isn't because the light is too intrusive, and it isn't just the converted that like it. Those are sweeping generalizations.
    It is much more likely that the non-glowing Apple logo on the new MacBook is just a regular Apple evolution of style. For example, the three colors in the MacBook are new to the Mac line, but they are identical to the iPhone/iPad line. Well guess what, the Apple logo has never glowed in the iPhone/iPad line. Therefore Apple may have simply decided to bring over the non-glowing Apple logo from the iOS devices to the Mac, just as they brought over the colors and brought over many of iOS user interface conventions to OS X.

Maybe you are looking for

  • Mark all clips from playhead/skimmer?

    Hey all, You FCP 7 users, you know the T tool (track tool), right? I used that for nearly all my edits. It very quickly selects everything from the point where you klick, down the whole timeline. Did you find that function in FCP X? I mean, when I wa

  • [SOLVED] Radeon (Xorg) Resolution

    I recently upgraded my monitor, from HD to UHD, and my graphics card so it was capable of powering the display. I tried to use the Catalyst driver but it crashes and so I've gone back to using the Radeon driver (I was using it with my previous graphi

  • One page will not load

    One of my pages will not load in BC.  States page not found. Gary

  • Why is there no responses when i install the oracle8i?

    I want to install oracle8i in my computer,but everytime when i double_clicked the setup.exe file(I just copied it from a disk),there is no responses.My o/s is windows2000 advance server. I have tried in another computer(os is windows2000 professional

  • HT3523 codec components Am I in need of software?

    Please assist, I have a Mac OSX Version 10.6.8 with Quicktime Player Version 10.0 (13) I am trying open a movie file titled 0015QX.mov but it won't open. The window that does open suggests that I may require "codec components" . Am I in need of softw