Apple only Screen

My I-pod is not working. All I have is a picture of the apple on the screen. It wont turn off or on and the button wont work.  I have tried plugging it in to different charger but the screen does not change. One time I saw the battery for a moment and it had minimal bar that was red.  Help

Hold the Home and Sleep/Wake button and then perform a restore http://support.apple.com/kb/HT1414

Similar Messages

  • My macbook pro will not boot. It gets the grey screen with the apple until the bar is half way across and then shuts down. The only screen I can get to is in safe mode and I don't know what to do with that

    my macbook pro will not boot. It gets the grey screen with the apple until the bar is half way across and then shuts down. The only screen I can get to is in safe mode and I don't know what to do with that

    Mac OS X: Gray screen appears during startup - Apple Support

  • I can start my iPod but it will only stay on the Apple icon screen for 5 minutes and then shuts off, what do I do to fix this problem?

    I can start my iPod but it will only stay on the Apple icon screen for 5 minutes and then shuts off, what do I do to fix this problem?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar

  • My iphone shows apple only in screen what is the problem?

    my iphone shows apple only in screen what is the problem? i can not open it

    Try a reset:  hold the on/off switch and home button simultaneously until the phone reboots--may take up to 20 sec.

  • Can anyone help with problem updating iphone5s cant get anything only apple on screen sometimes screen flashes blue

    can anyone help with problem updating iphone5s cant get anything only apple on screen sometimes screen flashes blue

    Hey damien555,
    Thanks for the question, I understand how frustrating this may be. It sounds like the update process may have been interrupted, and to resolve the issue, we’ll need to restore your device in recovery mode with iTunes:
    If you can't update or restore your iOS device
    http://support.apple.com/kb/HT1808
    Thanks,
    Matt M.

  • I have been taking photos for years and have thousands.  When I use Apple TV screen saver, it seems only to grab a handfull and repeats them.  Is there a configuration setting that will allow me to have the screen saver grab more than just a few?  Thanks.

    I have been taking photos for years and have thousands.  When I use Apple TV screen saver, it seems only to grab a handfull and repeats them.  Is there a configuration setting that will allow me to have the screen saver grab more than just a few?  Thanks.

    The device has an 8GB drive for caching streamed meida, a small portion of that is used to temporarily store photos for the screensaver. It may vary depending on resolution etc but it seems to be around 100.

  • Ipod touch wont switch on and constantly only shows the apple logo screen

    ipod touch wont switch on and constantly only shows the apple logo screen. Have tried to reset by holding both buttons down but hasnt worked. it also doesnt appear on itunes.

    Hvae you tried:
    - Reseting the iPod and then try restoreing the iPod
    - Placing the iPod in recovory mode and then restoring the iPOd.  For recovery mode see:
    iPhone and iPod touch: Unable to update or restore
    - Next try DFU mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings

  • Apple only on screen?

    I was charging my phone thru my computer now all i see is the apple on screen>

    Hold the Home and Sleep/Wake button and then perform a restore http://support.apple.com/kb/HT1414

  • Screen shows apple only after tring to updated wont turn off or change

    Tried to update Ipod 4 and restore as got screen with plug in to I-tune, went thru update but then froze with th apple on screen of I-Pod.  Now it wont reset wont turn on or off or be seen in I tunes.  Wont charge either Any help?

    Have you looked at this troubleshooting article?
    http://www.apple.com/support/ipodtouch/assistant/ipodtouch/
    You may need to restore.

  • My iPhone 3Gs randomly shutting off at any given moment. I could be in the middle of a text, a call, or doing some games and it'll just shut off.  Now here's the unique part. When I go to turn it back on, the apple loading screen pops up but it takes some

    My iPhone 3Gs randomly shutting off at any given moment. I could be in the middle of a text, a call, or doing some games and it'll just shut off.
    Now here's the unique part. When I go to turn it back on, the apple loading screen pops up but it takes somewhere from 3-5 minutes for it to boot up. Then the lock screen with the time and whatnot shows up. From this point on, my iPhone has a chance to shut itself back down and I have to repeat the process over and over again. Most of the time the lock screen flashes and then goes straight to black (shut down) but sometimes I can make it a few menus before it shuts itself down.
    The only way to keep the iPhone on is to plug it into a charger of any sort. I'm fairly certain it isn't a battery charge issue because this happens at any % of power and sometimes my iPhone can use up all of its charge and not have this happen while other times I can be at 90-100% and it could randomly shut itself down. What can I do in this situation if some has some solution to this problem please let me know on [email protected] Thanks!

    Not sure if this Term is Relevant towards an iPhone but, my iPhone won't Post unless if it's plugged into a Charger.

  • IPod Touch 4G Stuck On Apple Logo Screen

    So I just recently jail broke my iPod touch 4G and was using iFile to delete some default apps and stuff that was taking up space on my device.  I only need to use the Music app, so all of the other default apps can be erased.  I must have accidentally deleted something in regards to the music app because I am not able to transfer music onto the device using iTunes.  I turned my iPod off then and turned it back on and this is where the major problem came in.  It's stuck on the Apple Logo screen and will not boot back up or anything.  I have tried putting it in DFU mode and doing every kind of reset or restore and none of that has worked.  Now it doesn't even show up in iTunes.  Unfortunately I don't remember every thing I deleted when using iFile, so I cannot provide much information regarding that.  My iPod has worked perfectly fine until I jail broke it, which I probably shouldn't have even done but none the less if someone has any possible genius solution to my problem, I would appreciate you leaving a comment.  Thanks. 

    See if yo missed anything here:
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable                     
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • Single-User Mode Copying Files/System Does not Boot Past Apple Logo Screen

    I have a Macbook 2.0GHZ, 2GB RAM, that recently tried to download a secuirty and keynot update. Following the download the system will no longer boot past the Apple Logo Screen with the spinning wheel. I do not have access to a OS disk yet or to a firewire cable either. I've have seen posts from others that describe how to use traget disk mode to reinstall the secuirty update manually and then they can boot their computer. Safe mode will not work. I did boot into single-user mode and run the disk utility there and it says my HD is OK. Since I do not have a firewire or an OS Disk, I am wondering if there is a way to copy those files i need to a USB pen stick then install them onto the computer via single-user mode, considering this is the only way I can boot and manipulate the machine at this time. If this is not possible please let me know so I can find a way to scrounge up a firewire cable or disk. Thank you in advance for any assistance.
    Ted K

    Thanks to Limnos and BDAqua I know you guys have helped others with these kind of problems from the other posts I read. I just want to list what I did exactly in case anyone wants to try to do this with a usb drive or does not have access to a boot disk or firewire cable.
    1: Install security update on a pen drive
    2: Boot in single user mode, CMD-S on startup
    3: /sbin/mount -uw /
    4: mkdir /Volumes/usb (usb can be any name, name of usb drive or anything you want)
    5: ls /dev (you need to get the drive listing for the usb drive to mount it appropriately, it should be disk#s# but this is close to what the HD and Cd drives are listed as so you may need to list once before you put the usb stick in and once ater. I had issues inserting the usb drive in single-user mode and it would freeze up the root drive)
    6: /sbin/mount_msdos /dev/disk1s1 /Volumes/usb (this mounts the usb drive, i had to use msdos because of how my usb drive was formatted, you may need to check your usb drive format, hfs is the apple format for usb drives but it did not work for me)
    7: cp /Volumes/usb/SecUpd2009-001Intel.dmg (this copies the files from the usb drive to the root drivel, at this point you no longer need the usb drive)
    8: hdiutil mount /SecUpd2009-001Intel.dmg (this mounts the disk image)
    9: cd /Volumes/"Security Update 2009-001" (after i mounted the image this is how it appeared in the Volumes directory, you might need to do ls /Volumes to get the name, the quotes are important to get the whole file directory changed)
    10: installer -pkg SecUpd2009-001Intel.pkg -target / (this installs the acutal update, i used the SecUpd2009-001Intel.pkg and it worked though I think you might be able to use "Security Update 2009-001" with quotes as well.)
    11: reboot
    i hope this helps anyone looking to do this. Thanks again to those who helpes and all the other posts that had information that helped me identify and then fix my issue! I still love my mac.

  • My 2011 IMac will not boot up past the White apple logo screen with the whirly circle

    My 2011 IMac will not boot up past the White apple logo screen with the whirly circle. I have tried various commands but to no avail. does anybody have any advice?

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
    There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
    a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
    b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
    c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
    Step 3
    Sometimes a startup failure can be resolved by resetting the NVRAM.
    Step 4
    If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
    Step 5
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 6
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Step 7
    If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
    Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
    If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
    If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 8
    Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
    Step 9
    If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.   
    Step 10
    Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 11
    Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
    Step 12
    This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 13
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • IPhone top sleep/wake button is not working & Apple Logo screen at startup

    I have the original iphone. I have two problems, both just happened tonight at the same time. For seemingly no reason just my iphone external top sleep/wake button is not working. I tried powering the phone off and back on. I tried resetting my iphone, and restoring it. I made sure my Iphone software is up to date. None of these remedies have fixed the button. The button doesn't look broken, it pushes in and out, it just doesn't work anymore.
    Second problem is, after I power my iphone off and then back on, the Apple logo screen will continue to flash on and off indefinitely. The only way to get my home screen to appear is to connect my iphone to my computer. Then it wants to sync. After syncing it then asks if I want to "power off" or "cancel". Huh, why does is it doing that? To turn my iphone off I am pressing my Home button down until it shuts off, since I can't power off with the top black button. Is that the reason my phone is having the second problem, because I am powering off with the Home button? Could it be my second problem is not a problem?
    My iphone 1 year warranty is over. I can't call Apple Care, there is no apple store near me. I need a solution I can do at home myself. Please help. Even if you think the answer is obvious please suggest it to me. Before tonight nothing was wrong with my iPhone. It all started after I let my 6 and 7 year old nephews play with Google Maps on my phone for like 10 minutes - supervised. I consider myself to be a pretty Apple tech savvy guy, yet I can't figure out if they broke my iphone somehow, nor can I fix these two problems. Please help!

    Jason,
    I'm afraid I have good and bad news. Apple sent me a new original iphone. So that takes care of me but does not take care of the issue for so many people like you. I do not know if you can purchase the Apple Care plan at this time. Look into that. It really is worth it. Apple products require Apple technicians in the rare case the breakdown. Apple did not offer me an explanation of how they'll fix my phone or even saying why they sent me a new one. I synced it with Itunes and all my personalizations and apps are loaded back on it. It's like my old phone only shinyer and probably going to last me longer than the old one.
    I found out Apple Care covers the Iphone for 2 years past it's purchase date. So I would think that you could buy Apple Care even if you had it for like a year. Then it would at least cover you until the 2 year mark, which after that we're on our own(?). Please let me/us know if you were able to buy Apple Care protection and if they fixed your problem. I am impressed they got me a new phone so fast. I still love Apple.

  • Imac 5k stuck on apple logo screen after latest update

    Hi - i have a magazine deadline and a major issue:
    i've been having loads of kernel panics (see thread here Brand new imac 5k kernel panic) and having seen there was a new update figured it would be worth installing it to see if it fixed them as nothing so far suggested by apple support has helped. Once it had downloaded the update the OS said it needed to reboot to finish installation.  It got half way through the loading bar on the apple logo screen and got stuck. I left it an hour, came back still nothing. Left it another hour and it was still just stuck half way.  I rebooted into diagnostics and ran that and it said everything was fine but further reboots just get as far as halfway through the bar.  I'm now stuck as the computer was only a month or so old and i hadn't yet set up back up on it. I was still in the process of getting everything configured and over from my old machine.  Problem is I have a bunch of photos that were transferred on to it that i shot 2 weeks ago and I need them for a magazine deadline tomorrow and apple support options could only call me back on Thursday - if anyone can suggest anything i will be VERY grateful. I've already tried SMC and PRAM resets.

    I did that, a fresh OS install and it worked for about 4 hours then i got a kernel panic
    Anonymous UUID:       DE8E807F-E592-FD5D-3D3B-73B0BCCE57D4
    Fri May  1 00:30:12 2015
    *** Panic Report ***
    panic(cpu 0 caller 0xffffff8018f6bf28): "a freed zone element has been modified in zone kalloc.64: expected 0xdeadbeefdeadbeef but found 0xdead9eefdeadbeef, bits changed 0x200000000000, at offset 40 of 64 in element 0xffffff80647c1c00, cookies 0x3f0011bcd6adda0a 0x53521f311ca5c19"@/SourceCache/xnu/xnu-2782.20.48/osfmk/kern/zalloc.c:496
    Backtrace (CPU 0), Frame : Return Address
    0xffffff83c1ef3730 : 0xffffff8018f2bda1
    0xffffff83c1ef37b0 : 0xffffff8018f6bf28
    0xffffff83c1ef38e0 : 0xffffff8018f34601
    0xffffff83c1ef3910 : 0xffffff801945c513
    0xffffff83c1ef3950 : 0xffffff801945f027
    0xffffff83c1ef3980 : 0xffffff80194e958c
    0xffffff83c1ef39f0 : 0xffffff80194e90d2
    0xffffff83c1ef3a50 : 0xffffff7f9a79dcf6
    0xffffff83c1ef3ad0 : 0xffffff7f9a7a25e8
    0xffffff83c1ef3b20 : 0xffffff7f9a7a3350
    0xffffff83c1ef3b60 : 0xffffff80195017cf
    0xffffff83c1ef3bc0 : 0xffffff80194ff0c3
    0xffffff83c1ef3d00 : 0xffffff8018fe21e7
    0xffffff83c1ef3e10 : 0xffffff8018f3000c
    0xffffff83c1ef3e40 : 0xffffff8018f149f3
    0xffffff83c1ef3e90 : 0xffffff8018f2531d
    0xffffff83c1ef3f10 : 0xffffff80190031ea
    0xffffff83c1ef3fb0 : 0xffffff8019035396
          Kernel Extensions in backtrace:
             com.apple.iokit.IOAcceleratorFamily2(156.14)[BE7D765B-49C1-34F9-B75E-3EAF8A4062 A3]@0xffffff7f9a786000->0xffffff7f9a7f4fff
                dependency: com.apple.iokit.IOPCIFamily(2.9)[52E715FC-521D-3869-B2EA-5228FA4BEA34]@0xffffff 7f99724000
                dependency: com.apple.iokit.IOGraphicsFamily(2.4.1)[82EAD591-67E3-39CB-A232-A8095CA30E92]@0 xffffff7f9a72b000
    BSD process name corresponding to current thread: WindowServer
    Mac OS version:
    14D136
    Kernel version:
    Darwin Kernel Version 14.3.0: Mon Mar 23 11:59:05 PDT 2015; root:xnu-2782.20.48~5/RELEASE_X86_64
    Kernel UUID: 4B3A11F4-77AA-3D27-A22D-81A1BC5B504D
    Kernel slide:     0x0000000018c00000
    Kernel text base: 0xffffff8018e00000
    __HIB  text base: 0xffffff8018d00000
    System model name: iMac15,1 (Mac-42FD25EABCABB274)
    System uptime in nanoseconds: 19669481944459
    last loaded kext at 1177984628424: com.apple.filesystems.ntfs 3.12 (addr 0xffffff7f9c01d000, size 376832)
    last unloaded kext at 1401779154535: com.apple.filesystems.ntfs 3.12 (addr 0xffffff7f9c01d000, size 360448)
    loaded kexts:
    com.apple.filesystems.smbfs 3.0.1
    com.apple.filesystems.afpfs 11.0
    com.apple.nke.asp-tcp 8.0.0
    com.apple.driver.AppleBluetoothMultitouch 85.3
    com.apple.driver.AudioAUUC 1.70
    com.apple.filesystems.autofs 3.0
    com.apple.iokit.IOUserEthernet 1.0.1
    com.apple.iokit.IOBluetoothSerialManager 4.3.4f4
    com.apple.driver.AppleUpstreamUserClient 3.6.1
    com.apple.driver.AGPM 110.19.5
    com.apple.driver.X86PlatformShim 1.0.0
    com.apple.driver.ApplePlatformEnabler 2.2.0d4
    com.apple.driver.AppleGraphicsDevicePolicy 3.7.7
    com.apple.Dont_Steal_Mac_OS_X 7.0.0
    com.apple.driver.AppleMikeyHIDDriver 124
    com.apple.kext.AMDFramebuffer 1.3.2
    com.apple.driver.AppleIntelHD5000Graphics 10.0.6
    com.apple.driver.AppleHWAccess 1
    com.apple.driver.AppleOSXWatchdog 1
    com.apple.driver.AppleHDA 272.18
    com.apple.driver.AppleMikeyDriver 272.18
    com.apple.AMDRadeonX4000 1.3.2
    com.apple.driver.AppleHV 1
    com.apple.driver.AppleThunderboltIP 2.0.2
    com.apple.driver.AirPort.Brcm4360 930.37.3
    com.apple.iokit.AppleBCM5701Ethernet 10.1.3
    com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.3.4f4
    com.apple.driver.AppleSMCLMU 2.0.7d0
    com.apple.driver.AppleLPC 1.7.3
    com.apple.kext.AMD7000Controller 1.3.2
    com.apple.driver.AppleIntelFramebufferAzul 10.0.6
    com.apple.driver.AppleIntelSlowAdaptiveClocking 4.0.0
    com.apple.driver.AppleMCCSControl 1.2.11
    com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
    com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
    com.apple.BootCache 36
    com.apple.driver.AppleUSBHub 705.4.2
    com.apple.driver.XsanFilter 404
    com.apple.iokit.IOAHCIBlockStorage 2.7.1
    com.apple.driver.AppleSDXC 1.6.5
    com.apple.driver.AppleAHCIPort 3.1.2
    com.apple.driver.AppleUSBXHCI 710.4.11
    com.apple.driver.AppleRTC 2.0
    com.apple.driver.AppleACPIButtons 3.1
    com.apple.driver.AppleHPET 1.8
    com.apple.driver.AppleSMBIOS 2.1
    com.apple.driver.AppleACPIEC 3.1
    com.apple.driver.AppleAPIC 1.7
    com.apple.nke.applicationfirewall 161
    com.apple.security.quarantine 3
    com.apple.security.TMSafetyNet 8
    com.apple.iokit.IOSCSIBlockCommandsDevice 3.7.5
    com.apple.iokit.IOUSBMassStorageClass 3.7.2
    com.apple.security.SecureRemotePassword 1.0
    com.apple.driver.IOBluetoothHIDDriver 4.3.4f4
    com.apple.driver.AppleMultitouchDriver 263.9.1
    com.apple.kext.triggers 1.0
    com.apple.iokit.IOSerialFamily 11
    com.apple.iokit.IOSurface 97.4
    com.apple.driver.AppleGraphicsControl 3.10.22
    com.apple.driver.DspFuncLib 272.18
    com.apple.kext.OSvKernDSPLib 1.15
    com.apple.iokit.IONDRVSupport 2.4.1
    com.apple.iokit.IO80211Family 730.60
    com.apple.iokit.IOEthernetAVBController 1.0.3b3
    com.apple.driver.mDNSOffloadUserClient 1.0.1b8
    com.apple.iokit.IONetworkingFamily 3.2
    com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.3.4f4
    com.apple.iokit.IOBluetoothFamily 4.3.4f4
    com.apple.driver.AppleHDAController 272.18
    com.apple.iokit.IOHDAFamily 272.18
    com.apple.iokit.IOAudioFamily 203.3
    com.apple.vecLib.kext 1.2.0
    com.apple.driver.AppleSMBusPCI 1.0.12d1
    com.apple.kext.AMDSupport 1.3.2
    com.apple.driver.X86PlatformPlugin 1.0.0
    com.apple.driver.AppleSMC 3.1.9
    com.apple.driver.IOPlatformPluginFamily 5.9.1d7
    com.apple.AppleGraphicsDeviceControl 3.10.22
    com.apple.iokit.IOAcceleratorFamily2 156.14
    com.apple.iokit.IOSlowAdaptiveClockingFamily 1.0.0
    com.apple.driver.AppleSMBusController 1.0.13d1
    com.apple.iokit.IOGraphicsFamily 2.4.1
    com.apple.driver.AppleThunderboltEDMSink 4.0.2
    com.apple.iokit.IOUSBUserClient 705.4.0
    com.apple.iokit.IOSCSIArchitectureModelFamily 3.7.5
    com.apple.driver.AppleUSBHIDKeyboard 176.2
    com.apple.driver.AppleHIDKeyboard 176.2
    com.apple.iokit.IOUSBHIDDriver 705.4.0
    com.apple.driver.AppleUSBMergeNub 705.4.0
    com.apple.driver.AppleUSBComposite 705.4.9
    com.apple.driver.CoreStorage 471.20.7
    com.apple.driver.AppleThunderboltDPInAdapter 4.0.6
    com.apple.driver.AppleThunderboltDPOutAdapter 4.0.6
    com.apple.driver.AppleThunderboltDPAdapterFamily 4.0.6
    com.apple.driver.AppleThunderboltPCIDownAdapter 2.0.2
    com.apple.driver.AppleThunderboltNHI 3.1.7
    com.apple.iokit.IOThunderboltFamily 4.2.2
    com.apple.iokit.IOAHCIFamily 2.7.5
    com.apple.iokit.IOUSBFamily 720.4.4
    com.apple.driver.AppleEFINVRAM 2.0
    com.apple.driver.AppleEFIRuntime 2.0
    com.apple.iokit.IOHIDFamily 2.0.0
    com.apple.iokit.IOSMBusFamily 1.1
    com.apple.security.sandbox 300.0
    com.apple.kext.AppleMatch 1.0.0d1
    com.apple.driver.AppleKeyStore 2
    com.apple.driver.AppleMobileFileIntegrity 1.0.5
    com.apple.driver.AppleCredentialManager 1.0
    com.apple.driver.DiskImages 396
    com.apple.iokit.IOStorageFamily 2.0
    com.apple.iokit.IOReportFamily 31
    com.apple.driver.AppleFDEKeyStore 28.30
    com.apple.driver.AppleACPIPlatform 3.1
    com.apple.iokit.IOPCIFamily 2.9
    com.apple.iokit.IOACPIFamily 1.4
    com.apple.kec.Libm 1
    com.apple.kec.corecrypto 1.0
    com.apple.kec.pthread 1
    Model: iMac15,1, BootROM IM151.0207.B01, 4 processors, Intel Core i7, 4 GHz, 32 GB, SMC 2.22f16
    Graphics: AMD Radeon R9 M290X, AMD Radeon R9 M290X, PCIe, 2048 MB
    Memory Module: BANK 0/DIMM0, 8 GB, DDR3, 1600 MHz, 0x859B, 0x43543130323436344246313630422E433136
    Memory Module: BANK 1/DIMM0, 8 GB, DDR3, 1600 MHz, 0x859B, 0x43543130323436344246313630422E433136
    Memory Module: BANK 0/DIMM1, 8 GB, DDR3, 1600 MHz, 0x859B, 0x43543130323436344246313630422E433136
    Memory Module: BANK 1/DIMM1, 8 GB, DDR3, 1600 MHz, 0x859B, 0x43543130323436344246313630422E433136
    AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x142), Broadcom BCM43xx 1.0 (7.15.166.24.3)
    Bluetooth: Version 4.3.4f4 15601, 3 services, 27 devices, 1 incoming serial ports
    Network Service: Wi-Fi, AirPort, en1
    Serial ATA Device: APPLE SSD SM1024F, 1 TB
    USB Device: BRCM20702 Hub
    USB Device: Bluetooth USB Host Controller
    USB Device: FaceTime HD Camera (Built-in)
    USB Device: Keyboard Hub
    USB Device: Apple Keyboard
    USB Device: HD-PCU2
    Thunderbolt Bus: iMac, Apple Inc., 26.1

Maybe you are looking for

  • Thunderbird email links will no longer open on the Firefox browser. (I have to use another browser to open email links.)

    Since a recent update (either for Firefox or Thunderbird, don't remember which), links in my Thunderbird emails will not open in Firefox. I can't even open the Thunderbird "help" link. In desperation, I installed Opera, and the email links work perfe

  • Retriving Absence data from PNP logical database

    hi all, there is an function where i can get the absence data but my client wants in the following order But my client wants the report in following format: YEAR--- week number-- number of absence hourse in that week 2006 - WEEK - HOURS infotype is p

  • Receive error 'Adobe Reader 9.3 has stopped working'

    Good Day Everyone. Having difficulty opening a .pdf file.  Have used Adobe Reader 9.0 and 9.3 but without any success. Didn't used to have any problem opening pdfs but over last few months have experienced severql difficulties, which have resulted in

  • Total Before Discount field.

    Hi, evrybody! Can you show me about what table store Total Before Discount field..in SQL tables Can you help me! Thank you.

  • Get Memory Usage

    I need a suggestion for a light weight tool that will show the memory usage and also that can tell me which components are using more memory than others. I tried using JProfiler from my server but it is so slow to display the GUI on my machine. Somet