Apple TV (2) name, AirPlay dropouts and more.

I have 2 Apple TV 3's, each with a unique name. One located in the lounge, the other in a bedroom. Subsequently each named "Lounge" and "Bedroom".
I have run the same network and devices for almost 2 years, except for the addition of the iPad Air 2 and the iPhone 6. Apple TVs were on OS 6.x until the release of OS 7.x. During the period of OS 6.x i never ever had an issue with AirPlay from any Mac or iOS device. Which include MacBooks, Mac Minis, iPods, iPhones, iPads.
One Apple TV is connected via ethernet, the other is via WiFi (1 wall away which shows full signal when checked each time).
So i decided to update to OS 7.x when it came out and then i have been plagued with problems ever since, through each update 7.0, 7.0.1, 7.0.2 and 7.0.3.
There is three main problems with these 2 devices as a result of 7.x.
1 - Each Apple TV changes its name at random in regards to the number, one might be "Lounge" for a moment, the next it will be "Lounge (2)" or "Lounge (3)" and so on, usually reverting to "Lounge (2)", either during use or sleep mode.
2 - 90% of the time they will not wake from sleep for the AirPlay function from iPhone 6 on iOS 8.1.3, iPad Air 2 on iOS 8.1.3 or Mac Mini on Yosemite 10.10.2
3 - When it finally does wake, there are constant AirPlay drop outs, most of the time the AirPlay link will drop and some times disappear off the AirPlay devices list right afterwards.
Both Apple TVs produce the same issues, time and time again, i have restored them completely twice each, i have had one replaced for these issues under warranty, yet these issues still remain.
I have tried them on 4 different networks, i have even replaced my modem/router as part of this problem, and still these issues remain.
I even set up via a test with a personal hotspot from one of my iPads, so all i had was an Apple tv, iPad and iPhone on this wifi hotspot, the same issues were present there also.
During this time i have had iPad, iPhone and Mac complete restores for other issues which rules out issues with them i would like to think.
I have even tried AirPlay stability from my older iPhones, iPads and iPhones on iOS 6 and 7 - the same issues are present there also.
I have had many many cases with Apple Care opened, each case gets me no closer to solving generally because the "Senior Advisor" appointed to the case never responds to me after getting off the phone, despite them emailing me with their contact details to "follow up the case" so i don't feel any more efforts there will get me any closer at this point.
I have exhausted many options with no success.
Does anyone else have these same issues?
Has anyone ever found a fix?
Has anyone got any other methods of diagnosing the root cause of this?
I would love any info on this, I'm at my wits end with AirPlay.

Hello, I'm having the same issues using Beamer (one of the best apps ever created) and my Apple TV.
I’m using the latest versions of Beamer, Apple TV and OS X. It’s some weeks that when I drag a movie into Beamer it doesn’t connect automatically to my Apple TV as before: instead, I have to click the Share button and select the Apple TV, then everything goes fine as usual. I haven’t changed any settings, so it should “Connect and Pause” automatically as before.
I’ve also noticed that my Apple TV’s name displayed in Beamer when I click the Share button has changed from the original one (“Miller Apple TV”) to “Miller Apple TV (2)”. I don’t know why there’s this (2) in the displayed name. It’s like Beamer sees 2 Apple TVs named the same way and so it has to add (2) to the other one. But there’s only this Apple TV and the name of the Apple TV itself is always “Miller Apple TV”.
These 2 things (auto-connect not working any more and (2) added to Apple TV’s name) have happened together. It’s like Beamer doesn’t connect automatically anymore to “Miller Apple TV” because there’s another Apple TV named the same way and so it doesn’t know where to connect. I'm in touch with Beamer support but after looking your post I'm now thinking that the problem is more related to the Apple TV than to Beamer.

Similar Messages

  • Intune: No licenses, user name not recognized and more errors

    I've just activated our IUR from our Action Pack subscription.
    So, I go an Intune product key for 5 users for 1 year and set it up in the Intune Portal.
    So far, so good.
    My domain and users from Office365 have automatically transferred to Intune as well, so that's great.
    However, it seems the licenses won't activate or something.
    When I look at Subscription > Manage (or something like that, it's Dutch), it says 5 licenses until Aprl 2nd 2016.
    However, in Subscription > Licenses it says I don't have any licenses.
    Also, when going to any other portal (company or admin), it says 'User Name not recognized'.
    My main account is rowdy[A]noord-computers.nl
    Is there something more I should do? Or do I just have to wait a few days?
    Kind regards,
    Rowdy

    If you still see this problem, you should contact Microsoft support from the Intune portal.
    They can help you fix this problem.
    Ronni Pedersen | Microsoft MVP - ConfigMgr | Blogs:
    www.ronnipedersen.com/ and www.SCUG.dk/ | Twitter
    @ronnipedersen

  • Apple tv stutters when airplaying  music and movies

    I'm unable to utilize the airplay feature in itunes to watch movies or listen to music though Apple tv.  I've fooled around with my router and updated the firmware, I'm using all of the updates available to me with the exception of upgrading to mountain lion.  I never had these problems until I upgraded my phone and ipad to ios6.  Does anyone have a good starting point for troubleshooting this problem?
    Thanks guys

    Thanks for the reply WC
    Yes they do.
    They origialnally played just fine. I moved my entire iTunes library to a new computer and now only 62 songs, out of over 2000, and two of four movies won't sync. All songs and movies are in same folders and same format.
    I already selected "keep iTunes media folder organized" and "copy files to iTunes media folder when adding to library"
    using iTunes 10.7 and OSX 10.8.2

  • Apple ID:digits space less before @ and more after

    My mobile got wet(soaked) 6 days ago and after we restored the phone we faced with a problem. Because of the Find my Iphone app. its needed to log in with my Apple ID and password, the only problem is the @(in the e-mail address) shifted to the left with one digit, so we can not log in. The only problem is , we cant continue without checking in to my Appple ID. How can we solve this problem?

    This was resolved by repair disc

  • I want a new and more powerful (non-Apple) wireless router but I still want to use my existing Time Capsule to continue with my Time Machine backups and I still need the Time Capsule's Network Attached Storage (NAS) features and capabilities

    THE SHORTER STORY
    My goal is to successfully use my existing Time Capsule (TC) with a new and more powerful wireless router. I need a new and more powerful wireless router in order to reach a distant Denon a/v receiver that is physically located in a master bedroom some 50 feet away from my modem. I need to provide this Denon a/v receiver with an Internet connection so that it can obtain its firmware updates and I need to connect this Denon a/v receiver to my network in order to use its AirPlay feature. I believe l still need the TC's Network Attached Storage (NAS) features because I am not sure if the new wireless router will provide me with the NAS like features / capabilities I need to share files between my two Apple laptops with OS X 10.8.2. And I know that I absolutely need my TC's seamless integration with Apple's Time Machine (TM) application in order to continue to make effortless backups of my two Apple laptops. To my knowledge nothing works with TM like Apple's TC. I also need the hard disk storage space built into the TC.
    I cannot use a long wired Ethernet cable connection in this apartment and I cannot use power-line adapters. I have read that wireless range extenders and repeaters are difficult to successfully set-up and that they will reduce data speeds, especially so when incorrectly set-up. I cannot relocate my modem and/or primary base station wireless router.
    In short, I want to use my TC with my new and more powerful wireless router. I need to stop using the TC to connect to the modem. However, I still need the TC for seamless TM backups. I also need to use the TC's built in hard drive for storage. And I may still need the TC's NAS capabilities to share files wirelessly between laptops because I am assuming the new wireless router will not provide NAS capabilities for OS X 10.8.2 (products like this/non-Apple products rarely seem to work with OS X 10.8.2/Macs to provide NAS features and capabilities). Finally, I want to continue to use my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also want to continue to use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Can someone please advise on how to set-up my new Asus wireless router with my existing TC in such a way to accomplish all of this?
    What is the best configuration or set-up to accomplish my above goals?
    Thank you in advance for your assistance!!!
    THE FULL STORY
    I live in an apartment building where my existing Time Capsule (TC) is located in my living room and serves many purposes. Specially, my TC is at least all of the following:
    (1) Wi-Fi router connected to Comcast Internet service via Motorola SB6121 cable modem - currently the TC is the Wi-Fi base station that connects to the modem and has the gateway address to the Internet. The TC now provides the DHCP service for the Wi-Fi network.
    (2) Wireless router providing Internet and Wi-Fi network access to several Wi-Fi clients - two Apple laptop computers, an iPod touch, an iPad and an iPhone all connect wirelessly to the Internet via the TC.
    (3) Wired Ethernet router providing Internet and Wi-Fi network access to three different devices - a Panasonic TV, LG Blu-Ray player and an Apple TV each use one of the three LAN ports on the back of the TC to gain access to the Internet.
    (4) Primary base station in my attempt to extend my wireless network to a distant (located far away) Denon a/v receiver requiring a wired Ethernet connection - In addition to the TC, which is my primary base station, I am also using a second extended Wi-Fi base station (a Netgear branded product) to wirelessly extend my WiFi network to a Denon receiver located in the master bedroom and requiring a wired Ethernet connection. I cannot use a wired Ethernet connection to continuously travel from the living room to the master bedroom. The distance is too great as I cannot effectively hide the Ethernet cable in this apartment.
    (5) Time Machine (TM) backup facilitator - I use my TC to wirelessly back-up two Apple laptops using Apple's Time Machine (TM) application. However, I ran out of storage space on my TC and therefore added external storage to it. Specifically, I added an external hard drive to my TC via the USB port on the back of the TC. I now use this added external hard drive connected to the TC via USB as the destination storage drive for my TM back-ups. I have partitioned the added external hard drive, and each of the several partitions all have enough storage space (e.g., each of the two partitions used by TM are sized at three times the hard drive space of each laptop, etc.). Everything works flawlessly.
    (6) Network Attached Storage (NAS) - In addition to using the TC's Network Attached Storage (NAS) capabilities to wirelessly back-up two Apple laptops via TM, I also store other additional files on both (A) the hard drive built into the TC and (B) the additional external hard drive connected to the TC via USB (there are additional separate partitions on this drive for these other additional and non-TM backup files).
    I use the TC's NAS feature with my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Again, everything works wirelessly and flawlessly. (Note: the Apple TV is connected to the network via Ethernet and a LAN port on the back of the TC).
    The issue I am having is when I try to listen to music via Apple's AirPlay in the master bedroom. This master bedroom is located at a distance of two rooms away from the TC's current location in the living room, which is a distance of about 50 feet. This apartment has a long rectangular floor plan where each room is connected to the next in a straight line. In order to use AirPlay in the master bedroom I am using a second extended Wi-Fi base station (a Netgear branded product) to wirelessly extend my WiFi network to a Denon receiver located in the master bedroom and requiring a wired Ethernet connection. This additional base station connects wirelessly to the WiFi network provided by my TC and then gives my Denon receiver the wired Ethernet connection it needs to use AirPlay. I have tried moving my iTunes music directly onto my laptop's hard drive, and then I used AirPlay on this same laptop to connect to the Denon receiver. I always get a successful connection and the song plays, but the problem is that the connection inevitably drops.
    I live in an apartment building and all of the many wireless routers in this building create a great deal of WiFi interference on both the 2.4 GHz and 5GHz bands. I have tried connecting the Netgear product to each the 2.4 and 5 GHz bands, but neither band can successfully maintain a wireless connection between the TC and the Netgear product. I also attempted to maintain a wireless connection to an iPod touch using the 2.4 GHz band and AirPlay on this iPod touch to play music on the Denon receiver. Again, I was able to establish a connection and successfully play music, but after a few minutes the connection dropped and the music stopped playing. I therefore have concluded that I have a poor wireless connection in the master bedroom. I can establish a connection, but it is intermittent with frequent drops. I have verified this with both laptops by working in the master bedroom for an entire day on both laptops. The Internet connection in this master bedroom proved to drop out frequently - about once an hour with the laptops. The wireless connection and the frequency of its dropout are far worse with the iPod touch and an iPhone.
    I cannot relocate the TC. Also, this is an apartment and I therefore cannot extend the range of my network with Ethernet cable (I cannot drill through walls/ceilings, etc.). It is an old building with antiquated wiring and power-line adapters are not likely to function properly, nor can I spare the direct power outlet required with a power-line adapter. I simply need every outlet I can get and cannot afford to block any direct outlet.
    My solution is to use a more powerful wireless router. I found the ASUS RT-AC66U Dual-Band Wireless-AC1750 Gigabit Router which will likely provide a better connection to my wireless Internet in the master bedroom than the TC. The 802.11ac band of this Asus wireless router is totally useless to me, but based on what I have read I believe this router will provide a stronger connection at greater distances then my TC. And I will be ready for 802.11ac when it becomes more widely available.
    However, I still need to maintain the TC's ability to work seamlessly with TM to backup my two laptops. Also, I doubt the new Asus router will provide OS X 10.8.2 with NAS like features and capabilities. Therefore, I still would like to use the TC's NAS capabilities to share files on my network wirelessly assuming the Asus wireless router fails to provide this feature. I need a new and more powerful wireless router, but I need to maintain the TC's NAS features and seamless integration with TM. Finally, I want to continue to use my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also want to continue to use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Can someone advise on how to set-up my existing TC with this new Asus wireless router in such a way to accomplish all of this?
    Modem
    Motorola SB6121 SURFboard DOCSIS 3.0 Cable Modem
    Existing Wireless Router and Primary Wi-Fi Base Station - Apple Time Capsule
    Apple Time Capsule MC343LL/A 1TB Sim DualBand (purchased June 2010, likely the Winter 2009 Model)
    Desired New Wireless Router and Primary Wi-Fi Base Station - Non-Apple Asus
    ASUS RT-AC66U Dual-Band Wireless-AC1750 Gigabit Router
    Extended Wi-Fi Base Station - Provides an Ethernet Connection to a Denon A/V Receiver Two Rooms Away from the Modem
    Netgear Universal Dual Band Wireless Internet Adapter for TV & Blu-Ray (WNCE3001)
    Addition External Hard Drive Attached to the Existing Apple Time Capsule via USB
    WD My Book Studio 4TB Mac External Hard Drive Storage USB 3.0
    Existing Laptops on the Wireless Network Requiring Time Machine Backups
    MacBook Air (11-inch, Mid 2012) OS X 10.8.2
    MacBook Pro (13-inch Mid 2010) OS X 10.8.2
    Other Existing Apple Products (Clients) on the Wireless Network
    iPod Touch (second generation) is model A1288.
    iPad (1st generation)
    Apple TV (3rd generation) - Quantity two (2)

    Thanks Bob Timmons.
    In regards to a Plan B, I hear ya brother. I am already on what feels like Plan Z. Getting WiFi to a far off room in an apartment building crowded with WiFi routers is a major pain.
    I am basing my thoughts on the potential of a new and more powerful router reaching the far off master bedroom based on positive reviews on cnet.com, pcmag.com and pcworld.com. All 3 of these web sites have reviewed the Asus RT-AC66U 802.11AC wireless router as well as its virtual twin cousin 802.11n router. What impressed me is that all 3 sites rated this router #1 overall in terms of both range and speed (in both the 802.11n and 802.11AC flavors). They tested the router in real world scenarios where the router needed to compete with a lot of other wireless routers. One of the sites even buried this Asus router in a media room with thick walls and inside a media cabinet. This Asus router should be able to serve my 2.4 GHz band wireless clients (iPod Touch and iPhone 4) with a 2.4GHz Wireless-N band offering some 50 feet of dependable range and a 60 Mbps throughput at that range. I am hoping that works, but it's borderline for my master bedroom. My 5 GHz wireless clients (laptops) will enjoy a 5GHz Wireless-N band offering 150 feet of range and a 200 Mbps throughput at that range. I have no idea what most of that stuff means, but I did also read that Asus could reach 300 feet and I got really excited. My mileage may vary of course and I'm sure I'm making some mistakes in my interpretation of their data. However, my Winter 2009 Time Capsule was rated by cnet.com to deliver real world performance of less than that, and 802.11AC may or may not be useful to me someday. But when this Asus arrives and provides anything other than an excellent and consistent wireless signal without drops in the master bedroom it's going right back!
    Your solution sounds great, but I have some questions. I'm using OS X 10.8.2 and Airport Utility (version 6.1 610.31) and on its third tab labeled "Wireless" the top option enables you to set "Network Mode" to either:
    Create a wireless network
    Extend a wireless network
    Off
    Given your advice to "Turn off the wireless on the TC," should I set Network Mode to Off? Sorry, I'm clueless in regards to how to turn off the wireless on the TC any other way. Can you provide specific steps on how to turn off the wireless on the TC? If what I wrote is correct then what should the rest of this Wireless tab look like, or perhaps it is irrelevant when wireless is off?
    Next, what do you mean by "Configure the TC in Bridge Mode?" Under Airports Utility's fourth tab labeled "Network" the top option "Router Mode" allows for either:
    DHCP and Nat
    DHCP Only
    Off (Bridge Mode)
    Is your advice to Configure the TC in Bridge Mode as simple as setting Router Mode to Off (Bridge Mode)? If yes, then what should the rest of this "Network" tab look like? Anything else involved in configuring the TC in Bridge Mode or is it really as simple as setting the Router Mode to "Off (Bridge Mode)"?
    How about the other tabs in Airport Utility, can they all stay as is assuming I use the same network name and password for the new Asus wireless router? Or do I need to make any other changes to the TC via Airport Utility?
    Finally, in regards to your Plan B suggestion. I agree. But do you have a Plan B for me? I would greatly appreciate any alternative you could provide. Specifically, if you needed a TC's Internet connection to reach a far off corner of your home how would you do it? In the master bedroom I need both a wired Ethernet connection for the Denon a/v receiver and wireless Internet connection for the iPhone and iPod Touch.
    Power-Line Adapters - High Cost, Blocks at Least One Wall Outlet and Does Not Solve the Wireless Need
    I actually like exactly one power-line adapter, which is the D-Link DHP-540 PowerLine AV 500 4-Port Gigabit Switch. This D-Link power-line adapter plugs into your wall outlet with a normal sized plug (regular standard power cord much like any other electronic device) instead of all of the other recommended power-line adapters that not only use at least one wall outlet but also often block the second outlet. You cannot use a power strip with a power-line adapter which is very impractical for me. And everything about my home is strange and upside down. The wiring here is a disaster and I don't have faith in its ability to carry Internet access from the living room to the master bedroom. And this D-Link power-line adapter costs $90 each and I need at least two to make the connection to the Denon A/V receiver. So, $180 on this solution and I still don't have a dependable drop free wireless connection in the master bedroom. The Denon might get its Ethernet Internet connection from the power-line adapter, but if I want to use an iPhone 4 or iPod Touch to stream AirPlay music to the Denon wirelessly (Pandora/iTunes, etc.) from the master bedroom the wireless connection will not be stable in there and I've already spent $190 on just the two power-line adapters needed.
    Extenders / Repeaters / Wirelessly Extending the Wireless Network
    I have also read great things about the Amped Wireless High Power Wireless-N 600mW Gigabit Dual Band Range Extender (Repeater) SR20000G and the My Net Wi-Fi Range Extender. The former is very powerful and the latter is easier to install. Both cost about $150 ish so similar to a new Asus router. However, everything I read about Range Extenders points to them not being very effective for a far off corner of your house wherein it's apparently hard to place the range extender in the sweet spot where it both gets a strong enough signal to actually effectively extend the wireless signal and otherwise does not reduce network throughput speeds to unacceptable speeds.
    Creating a Roaming Network By Hard Wiring with Ethernet Cable - Wife Would Say, "**** No!"
    Even Apple seems to warn against wirelessly extending your network (see: http://support.apple.com/kb/HT4145#) and otherwise strongly recommends a roaming network where Ethernet cable is used to connect two wireless base stations. However, I am in an apartment where stringing together two wireless base stations with Ethernet cable would have an extremely low wife acceptance factor (WAF). I cannot (both contractually and from a skill prospective) hide Ethernet wire in the walls or ceiling. And having visible Ethernet cable running from room-to-room would be unacceptable, especially to the wife.
    So what is left? Do you have a Plan B for me? Thanks in advance for your help!

  • HT204053 Dear Support Team, every time i tried to logon Icloud its gives me wrong user name or password and at the end it show me error " This Apple ID is valid but is not an ICloud Account" then how can i use one account for same Apple ID and ICloud???

    Dear Support Team,
    Every time i tried to logon Icloud its gives me wrong user name or password and at the end it show me error " This Apple ID is valid but is not an ICloud Account" then how can i use one account for same Apple ID and ICloud?
    Thanks

    It is not possible to create a new iCloud account using a Windows machine. You must create the account using a Mac (10.7.5 or more) or an IOS device (iPhone etc). Once that is done you can sign into and use the account on your Windows machine.

  • Hello, my name is Karan Taneja and i have been a loyal Apple customer. I have been using Apple since it introduced iphone 4 and have been upgrading/buying every new phone Apple introduces after that. I was always happy and surprized to see Apple doing so

    Hello, my name is Karan Taneja and i have been a loyal Apple customer.
    I have been using Apple since it introduced iphone 4 and have been upgrading/buying every new phone Apple introduces after that.
    I was always happy and surprized to see Apple doing so good to its customers.
    Unfortunately, i experienced some thing really unprofessional and different this time.
    It begun suddenly one day when i tried to charge my phone, the phone was on silent mode and as usual the phone vibrated when i kept it for charge.
    After a few seconds the phone vibrated twice or thrice again when i re-inserted the cable thinking it might be loose.
    It continued to charge well when i left the room for 2 hours and finally when i returned i could see a damaged i phone 5
    lying on the floor and the phone vibrating continuously and i figured out there was a fault with the cable and the
    current wasnt flowing continuously due to which the phone continued to vibrate and fell off the shelf.
    Next day i took the iphone to Apple service centre at Saket which was closed.
    Thinking its August 15 and so the store might be closed i went back to home and waited for the next day but unfortunately could not turn up since
    i had to go to work on odd timings.
    I again went to the same service centre on 17th August 2013 and saw the service centre closed again when i tried to contact
    the other service centre and was informed about Saket's service centre already been shut down.
    There was no hoarding/ banner any kind of intimation for the customers.
    Since 18th August was Sunday and i was occupied on 19th August i went to service centre at Ansal Plaza Khel Gaon Marg on
    20th August 2013 to complaint about the Faulty Cable and the damaged caused to my iphone 5 due to the same.
    I very well explained the same to one of the person at the receiving desk at the service centre who accepted the cable
    but explained me that he doesnt have the authority to accept my iphone without permission from the technical support people
    who will be able to help me in that case and gave me the toll free number.
    i Tried to reach the toll free number and finally managed to get online with a technical support executives who too all my details and
    summary of the problem i experienced and finally kept me on hold for almost 10 minutes ormore after which he said he said that my
    case cannot be considered and while the discussion was on, the call was disconnected and i was left frustrated as i still was at the service centre
    but finally i left with no hope from Apple .
    I tried to reach again at the toll free number, and finally managed to talk to a well behaved person who assured me of considering my case and suggested
    me to go back to the service centre and advice the the person at the recieving end there to get me connected to the technical support team when i reach so that i could
    submit my phone but, since, it was already around 4:30 and the service centre was about to shut and due to traffic
    conditions all around i thought of visiting the service centre next day.
    On 21st August 2013, i went back to the service centre and spoke to the one of the store person who adviced the case to the manager Mr. Alok ( as i remember )
    who was really rude to tell me that i will have to call the technical support team on my own and then he will connect and that its not his work and all that .
    I finally connected to one of the senior technical support executives Mr.Mohamed Azharuddin K who understood my concern and spoke to the manager of the store to accept
    my iphone.
    My iphone was finally collected and i was assured i would get a call back next day from the service centre about the update.
    It was now 22nd August 2013, no update was given,no call was received, i tried to call the service centre at 12:30, they were unaware about my case and knew only about the cable and said will call me
    back very shortly.
    I called back at 2:30, still no update, at 4:30 i called back again when i was told that my case cannot be considered and i can collect my phone.
    Similar discussion was held with Mr.Mohamed Azharuddin K.
    I knew by the time i will reach the service centre would again close.
    He told me that my case cannot be considered since the cable was recieved in the dead condition and wasnt working at all unlike what i told him about the cable.
    On 23th August 2013, i went back to the service centre and collected my phone. When i asked about my old cable and told them that it was working and i wanted the technician
    to check it properly when i handed it over, they had no answer but to say its already shipped. I spoke to the manager who said that he never told any body that the cable
    was received in dead condition and he only conveyed to other authorities that the cable had fault .
    I finally dont know what to do and came back with the new cable.
    I just visited my time, petrol and parking charges in getting the cable replaced.
    If i calculated i have spent around 16 hours and 2000 worth of money in just getting the cable replaced and have a broken phone in hand.
    More than a weeks torture.
    Is that the way apple compensates for its fault ????????????????
    I will make sure that i never buy any thing from Apple and advice all the people i know to not trust Apple blindly.

    Wow, Karan Taneja, you've just embarrassed yourself on a worldwide support forum.  Not only is your post ridiculous and completely inappropriate for a technical support forum, but it also shows your ignorance as to whom you think the audience is.  Apple is not here.  It's users, like you. 
    If you would have spent half the time actually reading the Terms of Use of this forum that YOU agreed to by signing up to post, as you did composing that usesless, inappropriate post, you (and the rest of us on this forum) would have been much better off.

  • Airplay dropouts - only on some tracks in iTunes and not from iPhone

    Hi
    I experience heavy Airplay dropouts on certain tracks in my collection. And when I play the exact same track from my iPhone4 there is no problem. So I expect it to be an issue with iTunes and not a network bandwidth issue.
    What I noticed is that it occur more often on tracks with a high bitrate than on tracks with low bitrate - but not always. Almost all my tracks is 320 kbps mp3.
    However I've also experienced the problem on AAC tracks purchased from iTunes Store.
    And finally some podcasts play completely without any dropout, and others drop out after a few seconds.
    The above scenarios are easy reproduceable, and I think it might be an iTunes time specific problem when decoding the file and filling the airplay buffer.
    I don't think it's a general computer resource problem, as the max CPU usage is approximately 2-3% and 0-1% most of the time. There is also plenty of memory available.
    Are anybody else experiencing the same problem? Or maybe has a solution for the problem?
    Laptop facts:
    Dell E6510
    CPU Intel core I7
    Windows 7 64 bit.
    iTunes 10.2.0.34

    Have just tried Airfoil and then there is no problem. So it must be an iTunes issue...

  • Help! Bought a used iMac (2008) and I'm trying to install quicktime but its asking me for a password and has Apple in the "Name" spot.  How do I retrieve or reset the password?

    Can anyone help...
    I just bought a used iMac (2008) from an ebay seller and I'm trying to install quicktime but its asking me for a password and has Apple in the "Name" spot. 
    How do I retrieve or reset the password?
    It came with the upgrade of Mountain Lion but I cannot find quicktime in the applications.  When I try to install anything this Installer Password thing comes up... so I'm stuck.

    ShirlFromNC
    I think you're slightly misunderstanding something, so maybe I'll try to chime in, even though everyone has said it in various ways.
    Before OSX 10.7 (aka Lion) came out, the upgrades to OSX belonged to the Mac and not the user. Probably there was a technical legality in the user agreement that you couldn't do that, but everyone did. I could sell a Mac with Snow Leopard (or anything before that) by just erasing the hard drive, and reinstalling OSX. Then ship it to the buyer. Now, I was pretty honest as a seller, and including not only the original installation discs but also any upgrade. I would only sell a Mac if I was replacing it, so I always was getting the brand new version.
    With OSX 10.7, upgrading was done online, with no disks. So the upgrades were tied to an Apple ID rather than the machine. Recently, I sold a MacBook Pro (to upgrade to a 27" iMac), which came with Lion. I had promised the buyer that it would come with Mountain Lion, but I didn't know that the upgrade was tied to my Apple ID. I made good with the buyer by sending along a $20 Apple App Store card so that she could upgrade to Lion.
    So what everyone is saying here is that you need the original Installation discs or Snow Leopard disk to reinstall and wipe out the Mountain Lion that is on your Mac. It doesn't belong to you, it belongs to the seller, and without his Apple ID and password, you cannot use it. Once you do a reinstall of Snow Leopard, then you can upgrade to Lion and then to Mountain Lion. I do not believe you can upgrade directly to Mountain Lion from Snow Leopard, but I'm not sure.
    If the seller claimed that you were getting Mountain Lion, then he was lying to you (or being more civil, maybe he just didn't know like I did). If you bought the used machine from Amazon Sellers or from eBay, then you have recourse through the feedback system or through PayPal. If you bought it any other way, you're on your own.

  • HT204053 I want to be able to setup a generic corporate Apple ID to use with icloud and Find my Iphone, that will allow me to have more than 10 devices assigned to the ID. What do I do?

    I want to be able to setup a generic corporate Apple ID to use with iCloud and Find my iPhone, that will allow me to have more than 10 devices assigned to the ID. How do I go about creating this account?

    I'm not sure if I understand your question, but if you create a new iCloud account with a different ID your existing ID isn't effected by this.  It will continue to work as it does now, you will just have an additional Apple ID.  If you have an earthlink email address you can continue to use it as a separate account, and it can continue to be your default account if you set it to be (in Settings>Mail,Contacts,Calendars>Default Account).  If I'm misunderstanding your question, please explain further.

  • I want to hook up a mac mini and us my tv as a monitor. how can I use airplay from my phone on the mac mini like i can with an apple tv (without having to buy an apple tv!). the airplay capabilities i want to use are mirroring and streaming from my iphone

    i want to hook up a mac mini and us my tv as a monitor. how can I use airplay from my phone on the mac mini like i can with an apple tv (without having to buy an apple tv!). the airplay capabilities i want to use are mirroring and streaming from my iphone!

    Download AirPlayer for Mac - Transforms your Mac into an AirPlay-compatible display. MacUpdate.com

  • I have a game in the game center(clash of clans) and i have more than one apple mobile on the same account and i dont know how to delete the game(clash of clans) from the game center

    i have a game in the game center(clash of clans) and i have more than one apple mobile on the same account and i dont know how to delete the  game(clash of clans) from the game center.

    Hello ayhamnaser,
    Thank you for using Apple Support Communities.
    For more information, take a look at:
    Using Game Center
    http://support.apple.com/kb/ht4314
    If in Game Center > Me > Games > my iOS Games > swipe to the left on the game > Remove.
    Have a nice day,
    Mario

  • How to fix this error "this iPad is not able to complete the activation process. Please press Home and start over. If the issue persists, please visit your nearest Apple Store or Authorized service provider for more information or replacement"?

    How to fix this error "this iPad is not able to complete the activation process. Please press Home and start over. If the issue persists, please visit your nearest Apple Store or Authorized service provider for more information or replacement"? When I plugged in my iPad this popped up!

    Hi csreddy, 
    If you are receiving a message to contact an Apple Retail Store or Authorized Service Provider for help updating from iOS 3, click on the link below to initiate that support:
    Update the iOS software on your iPhone, iPad, and iPod touch - Apple Support
    http://support.apple.com/en-us/HT204204
    Update your device using iTunes
    If you can’t update wirelessly, or if you want to update with iTunes, follow these steps:
    Install the latest version of iTunes on your computer.
    Plug in your device to your computer.
    In iTunes, select your device.
    In the Summary pane, click Check for Update. 
    Click Download and Update.
    If you don't have enough free space to update using iTunes, you'll need to delete content manually from your device.
    Find out what to do if you get other error messages while updating your device.
    Last Modified: Jan 12, 2015
    Apple - Find Locations
    https://locate.apple.com
    Contact Apple for support and service - Apple Support
    http://support.apple.com/en-us/HT201232
    Regards,
    - Judy

  • I am trying to set up a genius bar appointment on my computer and it tells me "Sorry your session has expired. Please sign in again using your Apple ID account name and password" I know they are correct and use them to sign in on my phone.

    Hi I am trying to set a appointment for the Genus bar on my computer.  I know for a fact that my login is correct.  I have used it to sign in here and make a apointment (had to do it on my phone).  When I get to the appointment area it tells me to resign, and tells me "SORRY" Your lass session has expired.  Pleae sign in using your apple id account name and password.  I have tried resetting my password and all.  I am running Internet Explorer version 11 and my windows is 7.  Any help would be nice...

    ok.. I tried this three times and kept getting that access denied thing when I clicked post my questions. So now maybe I wont have to typ this a fifth time....
    I have a MAC computer with Sync. Was set up under sync Beta. I have an Android phone synced to it that was synced using the pair this device function. It works perfectly. I just got a new Android Tablet and am trying to add it to my sync and it does not seem to have the pair my device function. It insists I log into my sync account. So I try it and it tells me invalid userid/password. I verify and it is the exact email address userid that shows as being my sync account on the MAC. I verify the password on the MAC and it tests out fine. Try the tablet again and invalid.. So I try to reset my password on the tablet and am told my email address/account name does not exist. I just verified it AND Synced my MAC using it!! I have my recovery Key but there is no place to input it into the tablet. There is no place on tablet to enter the link device codes. How can my account be valid and in use on two devices but invalid and nonexistant on the new one? And How do I get the New one to sync with other two?

  • Many apps crashing after iOS 5 update and more. Think Apple will give me a trade-in?

    I just typed about a thousand words and lost them. I noticed that my owned hardware list hadn't been updated in years and tapped on it.  The back button returned me here and all that was left was the title of the post and the tags. NOTE: SPELL CHECKER DOES NOT WORK IN SAFARI SO THERE WILL BE TYPOS.
    I don't have the strength to type them again. Basically my 64 Gb iPad 1 is unusable in many ways after the update. I have lost too much work and play because of it.  It never gave me any trouble before and if I had the scratch, I would be typing away on an Android tablet right now. Long time user since iPod Touch G1 and have owned too many to list.
    Big one, you can no longer charge with older or 3rd party cables.
    WiFi dropped completely in further corner of the house until I turned on the dynamic indicator for the flaky location system that shows that I'm in every town around me, and some not around me, but not my town.
    Filling in dialogs in Safari is torture, cursor often disappears. Tap around to find it and Safari crashes.
    Key lag at times is so bad it gets a word behind. Scrolling in any app is jittery and jerky at the same time.
    There are so many more. I typedmup 3x more but lost all of it. This thing is so flaky I have been using my HTC EVO more and more and liking it more and more. If it had a min 7" screen there would be no contest.
    I don't want to give up my iPad, but it is always annoying me with its bad behavior, what good is it to me any longer?
    Do you think it is too old to take to the Apple Store and ask for a trade-in? I once toasted a $500 Touch with a firewire sync cable and Apple gave me another, no questions asked. Do you think?
    Just look at all the typos! I am a technical writer and it is embarrassing. Stinky keyslab+dead spell checker makes me look illiterate. Yes, the spell checker is turned on. I have spent many hours in the Settings applet in the last few weeks.

    I have iPhone 4 just updated to IOS 6 as well. App Store App updates are freezing on WIFI. I've twice had to delete the app and re-install. Installs of apps are also failing, causing the app to be unusable. At that point because it is a 'new' install the app can't be deleted. So the app can;t be deleted or installed.
    IOS 6 on iPhone 4 also seems a bit laggy.

Maybe you are looking for

  • Installation problem for Oracle 9.2 on Win XP pro

    This is what I have done so far: 1. Launch Setup 2. Specify the Product Key and Home Directory 3. Select Database Option 4. Select Personal Edition (I am a student) 5. Click Install The Installer starts and I see a progress bar on top. It goes till 3

  • Itunes Hangs as soon as iPad or iPhone connected

    I am running OS X 10.9.3 on a MacBook Air with Itunes 11.2.2 (3). iTunes runs quite happily until i plug my iPad in. The iPad is identified and then iTunes hangs. I have disabled automatic synching but I am at a loss as to what to try next. I powered

  • LSMW  Field Mapping: can't map Batch Input Structure for Session Data

    In step 5 Maintain Field Mapping and Conversion Rules, I can not see Batch Input Structure for Session Data Fields. Can somebody tell what's wrong? Here's what I see: Field Mapping and Rule         BGR00                          Batch Input Structure

  • Supertype and Subtypes

    Hello, I created an employees table with 3 types, although when I insert the values, it works but doesn't display the last value which is from a different type. Any idea how to fix this? DROP TYPE employees_type FORCE; DROP TYPE hourly_employees FORC

  • Flex Regex Help

    Hi there, I have a regular expression that is used to validate names in my application. It's intended to only allow alphanumeric names and spaces. My trouble started when I tried to modify it to also accept other unicode characters (umlauts and whatn