Apple TV (2nd Gen) + Remote not working

My Apple TV 2nd Gen / remote isn't working.
When I press any button on the remote I get no response at all from the Apple TV unit (no flashing lights etc).
I've replaced the battery with brand new battery, still no joy.
I've tried the "hold menu rewind for 6s", still no joy..
Any ideas?

Also to be clear, the Apple TV unit is displaying an image on my TV screen and I get a solid white light all the time.

Similar Messages

I set up a new airport time capsule. Most devices work fine however now my apple tv 2nd gen won't work.

I set up a new airport time capsule. Most devices connected fine however now my apple tv 2nd gen won't work. I turn it on and it searches for time and date but goes no further. I can't by pass it either. Any suggestions?

I can't by pass it either. Any suggestions?
Does that mean you cannot move it to the TC and plug in by ethernet? What does bypass mean?
I would still move it closer to the TC.. and just trial it there. Range on some AC models for 2.4ghz is worse than old one. For some people.
Another thing to try is fixed wireless channels.. one of the very few options still available in the AC model.. lock the 2.4ghz to 11, 6, 1 .. try it in that order.

2nd gen shuffle not working windows 7

I connected my 2nd gen shuffle to my laptop (Windows 7) and it told me I need to restore it, but Itunes keeps crashing every time i tried. I restared my pc, then it stopped showing in Itunes but showed on devices, and was on. Now it does nothing at all, no lights or anything. Any help appreciated

I have two suggestions. There is an iPod Reset Utility
http://support.apple.com/kb/HT1238
that is only for the 1st and 2nd gen shuffle. It does something like a Restore in iTunes, but works at a "lower" level in cases when a Restore in iTunes does not work (or cannot be used). For it to work, the shuffle does need to be seen by the system, and it sounds like yours meets that requirement.
Unfortunately, I don't think it works with Windows 7. If you happen to have an older PC with 32-bit Windows, you can use that PC to run the utility on the shuffle. Or, maybe you have a friend with a Mac or 32-bit Windows PC that can run it for your. Or, if you have an Apple Store nearby, you can make a reservation at the Genius Bar and ask them to look at it and run the reset utility.
The second suggestion, if you don't have a convenient way to use the reset utility, is to use Windows to reformat the shuffle's storage like it was a flash drive. Use a "full" format (not the "quick" option). Use the "FAT" format type. Make sure iTunes is NOT running. After it is reformatted, it will be blank. When you run iTunes, it should recognize the shuffle and ask you to Restore it (to re-install the software and set it to default settings). Hopefully, it will work this time.

IPod Touch (2nd gen) - Does not work with Component AV Cable

I have a 2nd generation iPod Touch. Today I bought the component AV cable at the Apple store (along with a universal dock). Connected it correctly to the TV and:
1. No picture (screen is blue, as though nothing connected); no sound (whether video or music)
2. Whatever video is playing on the actual iPod gets stuck - as though it is on "pause", with the difference that you can push "play" and "pause" and the only thing that does is change the "play" or "pause" icon from one to the other or vice-versa--video will not actually play
3. Setting Widescreen to "on" or "off" has no effect
4. Tried connecting it to an old iPod Nano (2nd gen I think) - also no sound.
Please advise!

Alex_K
Try changeing your TV out setting, found in the (Settings) of your ipod. Following Paragraph found in the iPod User manual (Page 98): http://support.apple.com/manuals/#ipodtouch
"Use these settings to set up how iPod touch plays videos on your TV. For more
information about using iPod touch to play videos on your TV, see “Watching Videos
on a TV” on page 39.
Turn widescreen on or off: Choose Video and turn Widescreen on or off.
Set TV signal to NTSC or PAL: Choose Video > TV Signal and select NTSC or PAL.
NTSC and PAL are TV broadcast standards. iPod touch displays NTSC 480p/PAL 576p
when attached to a TV using a component cable, or NTSC 480i/PAL 576i using a
composite cable. Your TV might use either of these, depending on where you bought
it. If you’re not sure which to use, check the documentation that came with your TV. "
Hope that helps,
Weston

The latest update (9/2/11) for iPod 2nd Gen will not work

This is getting frustrating, I can't downlaod any apps and its moved like 1% in a hour

The last update for 2nd gen ipod touch is 4.2.1 and was released in nove of 2010.
Is this the update to which you refer?

Apple TV 2nd gen remote does not pause a Netflix movie

Streaming from Netflix works fine, but the Apple TV remote cannot pause or stop the movie without completely coming out of the Netfix App. Pause / play button does nothing. Menu button puts up the previous Netflix screen, but the movie keeps on playing in the background.
Remote works fine under all other circumstances. Apple TV firmware is up-to-date.

did you resolve this, i am having the same problem.

Restoring 2nd Gen iPod not working

For some reason, my iPod got stuck when attempting to play. I went to the forum and found out that I needed to restore my iPod. However, I get this message:
There was a problem downloading the iPod software for the iPod “iPod”. You do not have enough access privileges for this operation.
I tried deleting "temp" folder. Didn't work.
I tried working on the "ipod services". Didn't work.
Does anyone know how to solve this? THANKS in advance.

Restore to factory settings.new iPod if you have not yet already. If still problem time for an appointment at the Genius Bar of an Apple store.

Airport 2nd Gen. Not Working; Worth Selling?

Hello,
Recently upgraded to a 5th Generation that seems to be working better with modem. With 2nd Generation would have to unplug the router to connect to the internet several times daily. The firmware on the 2nd was updated. I was using 2.4ghz not 5 if it even would make a difference. Is the older Airport even worth salvaging? I thought about selling on eBay as is. Would appreciate any feedback. Thank you.

Check Ebay to see what other similar models are selling for to get an idea of what it might be worth.

Apple TV (2nd gen) not showing up as a device in iTunes

Hi all,
I have this problem. The Apple TV (2nd gen) does not show up in iTunes under devices, and I really don't know why.
Mac OSX 10.6.5
iTunes 10.1
AppleTV 2nd gen with latest update installed
Network is a WiFi Airport Extreme (Mac and AppleTV are indeed on the same private network)
Airplay works, home sharing works fine. Remote App on iPad and iPhone works.
But the AppleTV is not showing up under devices.
I had a 1st gen AppleTV which I reverted to "factory settings" before unplugging. The 2nd gen ATV had the same name as the 1st gen at the beginning, but I changed it afterwards figuring it might be related.
Under iTunes > preferences I had the AppleTV tab. But I did read somewhere on Apple's site you have to "delete" the AppleTV from the list. So I did, and now the tab cannot be found anymore...
Can anyone help?
Thank you in advance.

iMat77 wrote:
I seem to recall though that I have seen a screenshot somewhere on the web where iTunes showed the ATV 2nd gen as a device.
Not seen that, but the old ones have a logo that look (to me) like the new one, or at least a small darker grey than they are - they show up nicely in the iPad/iPhone Remote app though
If you are right it would be huge disappointment!
I believe I am correct as I've got new/old AppleTVs connected to 3 Macs and a dual boot Mac Pro currently, and the new unit has never appearede under devices.
.... I really HATE the interface organization right now. Why on planet earth do I have to go under "devices" -> "computer" -> "music" just to play some music?
You, me and many other AppleTV 1 users. I think they'd finally got it right in 3.02 for AppleTV 1 which is a much nicer user interface. Basically now the majority of the top level columns are unused by many people who don't rent but want to playback theit iTunes media.
I firmly believe Apple see this new AppleTV as a relatively cheap accessory for iPads/iPhones/iPods to show video/photos via Airplay on your TV without using a computer.
Secondly it's a vehicle for pushing itunes Store rentals, but for the majority of worldwide users they can only get Movie rentals, and Netflix is of no use bar in a few countries (US/Canada).
I would have much more preferred that a "music" tab (it also applies to all other tabs, movies, tv series and so on) and then just a list of all "home sharing" connected computers from which I could pick the one where the music is stored. Or even, and being Apple it surprises me they didn't implement it, just the list of the available music on my network, with a little tab indicating in which computer it is located.
Yes that would make absolute sense - a dynamic list of available content based on connected libraries that changes as new libraries appeared on/left the local network.
The new menu organisation is quite shoddy to me, ut many users new to AppleTV like it and rave about the devices not knowing what the old one could do - it's a good device don't get me wrong, but I still prefer the older units except for their power consumption and the fact I feel they are more likely to fail due to their high temps and mechanical hard drives.
But here I'm venturing FAR off topic.
Don't think so, it's a valid comment.
Use this:
http://www.apple.com/feedback/appletv.html
Thank you for your help anyway. I wait for confirmation of somebody else just to make sure...
Fair enough.

My Apple TV (2nd Gen) woun't boot it'a a blinking fool, and Reset does not work... Is it time to by a new WD Live or is it just me? Thanks All..

My Apple TV (2nd Gen) won't boot it'a a blinking fool, and Reset does not work... Is it time to by a new WD Live or is it just me? Thanks All..
If I mess this up ... sorry it my first time....

I found this after posting here:
http://trick77.com/2011/02/04/apple-tv-2-with-white-led-flashing-blinking-fast/
It appears that this is due to firmware corruption and you can fix it by using the micro USB cable and hooking it to iTunes. I have not tried it yet but supposedly several people were able to resolve their problem this way. If you do try it, let me know. I don't have the cable at this time.

HT1551 I just ran an Apple TV (2nd Gen) update. Now it's not working!

I just ran an Apple TV (2nd Gen) update. When it finished, all that appears on the screen is an iTunes logo and a picture of a cable beneath it. Also, the light on the Apple TV box flashes incessantly. What's going on?

Do a search for older articles with the keywords "appletv white screen".
You'll find things like:
https://discussions.apple.com/message/9576685#9576685
https://discussions.apple.com/message/11207194#11207194

HT1947 Cant update my Apple TV (2nd Gen) with Remote app?

I have been using the Remote app on my iPhone 4 top successfully control my Apple TV (2nd gen) for a while now after my Apple TV remote dropped in the toilet and stopped working! Now my Apple TV needs to update (Update Now/Update Later) and when I try to connect the Remote app to the Apple TV the Remote app just spins continuously and never finds the Apple TV, therefor not allowing me to select "Update Now". What to do? Do I now need to buy an Apple Remote? Hoping I dont have to.

Hi and thanks for your suggestion. Unfortunately this didn't solve the issue. I tried almost everything now:
- I rebooted the WIFI rooter
- I resettled the apple TV
- I removed the cables of apple tv for a minute (I have a switch anyway to cut power off completely)
- I killed the remote app on the iPhone and iPad a few times
- I removed my account settings both on the i-devices and apple tv for home sharing a few times and activated them again
All of the devices are in the same wifi network and every device can connect perfectly to the internet.
The screen on the iPhone/iPad always just shows that I should activate home sharing on iTunes on the computer or on the apple tv with my account (what I did as mentioned above)
Any ideas, someone from Apple maybe?
Any ideas appreciated!
Markus

HT1947 Apple TV (2nd gen) and Remote App - no more connection

Since updating to the latest version of Apple TV (2nd gen) and Remote App for iPhone or iPad I can't connect any more. Worked for a short moment after restarting a few times but now no more. Must be a new bug, because it always worked before updating to iOS 5.1!
I tried with an iPhone 4S and and iPad 2.

Hi and thanks for your suggestion. Unfortunately this didn't solve the issue. I tried almost everything now:
- I rebooted the WIFI rooter
- I resettled the apple TV
- I removed the cables of apple tv for a minute (I have a switch anyway to cut power off completely)
- I killed the remote app on the iPhone and iPad a few times
- I removed my account settings both on the i-devices and apple tv for home sharing a few times and activated them again
All of the devices are in the same wifi network and every device can connect perfectly to the internet.
The screen on the iPhone/iPad always just shows that I should activate home sharing on iTunes on the computer or on the apple tv with my account (what I did as mentioned above)
Any ideas, someone from Apple maybe?
Any ideas appreciated!
Markus

Apple remote not working

My Apple remote is not working with my MacBook. The Mac OS X 10.5 Help Knowledge Base says to go to Security > Systems > and Disable remote control infrared receiver. I don't have a systems button or box nor the checkbox to Disable remote control infrared receiver. And, my MacBook has an infrared receiver.

Hi Focus,
I have the same problem. When I update from TIger to Leopard the front row apple remote still working. But is been a long time the last time i used and now on 10.5.2 osx the apple remote not working as I imagine.
I read some answers that help me understand better the problem. My check box of "disable remote.."is unchecked and I saw a "pair" button and try to pair with my apple remote. The tips told me to HOLD "menu" and "next" buttons of apple remote to pair him with computer. And Works fine. So I try to push only Menu button (as I've done so many times on tiger) but still does not working. So I realize the command to "start front row from apple remote" now on Leopard 10.5.2 is MENU+NEXT buttons and does not anymore only menu button. For me works like this.
While I write this answer I try again push and hold only MENU button and after almost 2 or 3 seconds holding button appears on screen an virtual image of my apple remote signaling to replace the battery, may be now will be works only on push menu, but I need to change the battery first.
I hope help somebody.

Apple infrared remote not working

Just a few days ago I updated Keynote, my time scale is a little hazy but I know recently, like last week, I used my appl infrared remote to control Keynote. I was able to press play and advance slides. This was a great thing, I remember doing and thinking wow apple is great. Now it doesn't work. I can turn the volume up but playing or advancing the slides does nothing. It sure seems like the last update removed this feature.
Anyone know whats going on?
Thanks,
Kris

Hi Kris,
If you are having an issue with your Apple Remote not working with your Keynote presentations, I would suggest that you troubleshoot using the steps in this article -
Troubleshooting the Apple Remote - Apple Support
Start with the section titled If you're using the remote with a computer.
Thanks for using Apple Support Communities.
Sincerely,
Brett L

Apple TV (2nd Gen) + Remote not working

Similar Messages

Maybe you are looking for