Apple TV and/or Airport extremely slow syncing - Unique or common problem?

This is my first post and I'd appreciate help.
My Apple TV has worked fine for the last few weeks but started playing up last weekend. It now syncs either very slowly or not at all. Have tried every workaround suggested in this forum. Also spent 3 hours on phone with Apple technician this morning who could not diagnose problem (but has gone away to consult internally).
Apple TV is (was) connected wirelessly to Airport Extreme which is connected via ethernet cable to iMac, with all the latest software installed on everything.
Factory resets of both Apple TV and Airport Extreme worked for a bit, then same problem re-emerged. Direct ethernet connection of Apple TV to Airport Extreme also worked for a bit, but then same problem appeared, and then Apple TV disappeared from Devices list in iTunes and could not be recovered even after reboot. Direct connection to iMac also worked initially, but then same problem (slow syncing, then disappears from Devices list) re-emerged. Can see Apple TV in Devices in iTunes if wireless connection is restored, but only with extraordinarily slow syncing.
Anyone know what the problem might be? Is it unique or common? Any suggestions for fixes?
iMac 2.16 GHz Intel Core 2 Duo Mac OS X (10.4.10) Airport Extreme, Apple TV

By current release software I was referring to the AEBS firmware, the Apple TV software and iTunes. You can run the "Check for Updates" tool for each to make sure that they are up to date.
Since you reported the same problem when connected either by Ethernet cable or by wireless that would obviously rule out any wireless problems such as RF interference. The only possibilities left would be that something else is loading down your network or there is a hardware failure somewhere.
If there is a bad component in the AEBS I would expect it to affect your computer as well as the Apple TV. If there is a hardware failure in the Apple TV I would expect it to show up whether syncing, streaming or watching movie trailers or YouTube videos.
One other possibility might be that if you have any anti-virus software on your computer it might slow things down if it is scanning the files while they are syncing or streaming.
iMac Mac OS X (10.4.9) The more I think, the more I think I shouldn't think more.

Similar Messages

Blackberry desktop for Mac and Bold 9900 - extremely slow syncing?

Is it just me or does it take forever just to sync a few changes to photos or music to my Bold 9900 using the Blackberry desktop on mac? Ok granted the first time I added over 1000 songs, several playlists and about 40 photos from iPhoto via the sync software, it took over 3 hrs to sync. Personally I find that extremely slow, especially when comparing to my ipad or iphone and itunes syncing. Today I wanted just to remove one photo album from my phone, so unticked it and resynced again. Over half an hour before it finished! The registering media with device step takes a very long time, as does the initial preparation stage...... surely there must be something wrong?
Without the wifi sync feature i can't imagine it being practical just to add one song to my phone through this software before popping out with the phone in the car.... I would need to give myself over 30 minutes in advance.
Any advice or help most appreciated.
Thanks
Simon

Hey midinotes,
Welcome to the BlackBerry Support Community Forums.
It can take quite awhile to synchronize media to your BlackBerry. Especially with the songs, 1000 songs it is normal to take a few hours.
The easiest way I add music to my BlackBerry is dragging the media files to the media card. It's a lot quicker.
-ViciousFerret
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Like! for those who have helped you.
Click Accept as Solution for posts that have solved your issue(s)!

How to connect my new Time Capsule and new Apple TV to my Airport Extreme?

Hello, I just moved into a new apartment with one DSL outlet for internet from the kitchen. I set up an Airport Extreme in the kitchen without a problem. But I don't know how to set up the TIme Capsule in my home office and the Apple TV in my living room? Can someone help me? Thank you very much!
Ray

I would try to connect the Extreme and the TC by ethernet for a more reliable and faster network. The secondary router must be in bridge mode, use Airport Utility "manual" to set that up.
Once your network is tested by yourself and reliable then power up ATV and use the remote to go to setting. Assuming you have a main computer with your itunes library setup and launched without sleeping then go to ATV settings/computers and point to your computer which has your library. ATV should give you a 5 digit code. Enter this in your itunes column on lefthand side, its self explanatory assuming in itunes preferences you have checked under ATV "look for ATV."

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

HT1218 After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer. We still have wifi but cannot access the base station software.

After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer. We still have wifi but cannot access the base station software.

Thanks for the reply. I appreciate the response. I tried that approach this evening and it didn't work for me. (Technically it worked for me, when I was hardwired into my base station, but would not work for me wirelessly, which is my main issue.)
Again, using the approach you recommended works only if I have my ethernet cable attached to the LAN port so my computer is communicating directly to the base station through the hard wire. I am able to scan for my base station and make setting adjustments normally this way too.
As soon as I disconnect from the LAN port and try to go wireless is where I run into problems. The Base Station's wireless network I created is available to choose in the top right corner of the monitor with all of the other available wireless devices/networks -- but the network I created does not have access to the internet. I am also unable to configure my Base Station wirelessly. When my Airport Utility tries to scan for the Base Station and Network, it cannot find any Apple Wireless Device. It's like the Wireless Network in my base station is not sending out a signal.
Is there a way to resolve this issue?

Can I use non-apple notebook to connect AirPort Extreme?

I
Can I use non-apple notebook to connect AirPort Extreme?

He might be trying to do so to promote his products or may be there was some misunderstanding.
Airport Extreme will work as a wireless router supporting upto 50 systems including Mac computers, PCs, iPad, iPhone, iPod touch, Apple TV and virtually all 802.11a/b/g/n Wi-Fi wireless devices — all at the same time.
for reference http://store.apple.com/us/product/MD031LL/A/AirPort-Extreme

I have a Cisco/Linksys WRT-54G wireless router and 2 Airport Extremes (the small ones that plug directly into the wall). Is it possible to extend the network from the router using these two AEs? I have a DVD player and Ext HD plugged into the router too..

I have a Cisco/Linksys WRT-54G wireless router and 2 Airport Extremes (the small ones that plug directly into the wall). Is it possible to extend the network from the router using these two AEs? I have a DVD player and Ext HD plugged into the router too. Any ideas? I'm guessing the only way is to do what I've seen in these community pages which states that it can be done but it will drop the bandwidth by 50%. Thoughts?? Thanks!

The Cisco/Linksys WRT-54G was one of the very few routers said to be compatible with Apple's implementation of WDS (Wireless Distribution System) settings.
The info that I have on file indicates that only the WRT-54G versions 4 and under were compatible, so that would be one bridge to cross.
Even if you find that your Cisco/Linksys might be the right version, Apple never published instructions on how to configure the Express devices with other manufactures, so users were left to their own devices to try to figure out how to get things working. Apple's instructions to connect to other Apple devices are in the link below:
WDS network
If you were hoping to use 2 Express devices in this type of configuration...even if it works...the bandwidth penalties will be extremely severe.
The first Express drops the bandwidth (and speed) on the entire network in half and the second halves everything again. So, the result, in effect would be a "g" wireless network running at 25% speed. Few users would consider installing this type of network.
At this point, it becomes one of those things where the fact that you might be able to do something does not mean that there would be much value in doing so. But, it is your decision to decide if you want to try to proceed.

I have changed my apple id, and its ok when i sync my Iphone with Itunes, but ON my Iphone still my old apple-ID is there. I can NOT buy things from Itunes or Upgrade anything now, how to fix this?

I have changed my apple id, and its ok when i sync my Iphone with Itunes, but ON my Iphone still my old apple-ID is there. I can NOT buy things from Itunes or Upgrade anything now, how to fix this?

I recently changed my email address and want to change my Apple ID account to match. I have created a new Apple ID to match the new account but now I can't sign into iCloud on our phones or computer with the old Apple ID. I can't make any changes on iCloud on our phones because it directs me to the old account, which I can't sign into. I also can't sign me in on my computer to make any changes. Help!!! Now I have two addresses and can't access the one that directly affects my devices.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

I have an Apple TV and an Airport Express, can I use these to stream all audio from either my iPhone or my MacBook Pro, including Pandora?

I have purchased an Apple TV and an Airport Express as a gift for a loved one and was under the impression that these two would not only allow for movies, videos etc would be streamed to the TV from my MacBook Pro, but also set up Airport Express with speakers and stream music from my laptop or iPhone. Is there a way for all music, including Pandora, to be streamed through the Airport Express? I can only figure out how it works with iTunes, not Pandora.
Thanks for the help!!!

You might want to take a look at Airfoil for Mac to be able to stream any audio source on your Mac.
Rogue Amoeba | Airfoil for Mac: Wireless Audio Around Your House

Using Epson Workforce 40 with Snow Leopard and an AirPort Extreme

Hi. Long night working on this but I figured something out, that might help others out there in the same/similar situation.
I have an Epson Workforce 40, and an AirPort Extreme. I had previously set up the EPWF40 (Epson WorkForce 40) before I had installed Snow Leopard. After installing Snow Leopard, the printer would not work and would not be recognized by my MBP 15". The document would just hang and I would have to force quit the printer or delete the document.
Bullet points on how I made it work:
- the most important thing is to have the printer recognized by the router and have an IP address installed and registered first, then you can install the Epson Mac EasyPrint software and "find" the printer over your wireless network
- Goto:
http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?oid=108743&prodoid=6307 5463&BV_UseBVCookie=yes&infoType=Downloads&platform=Macintosh&x=28&y=3
and download the Epson EasyPrint v3.10 file called: "epson12433.dmg"
- Unfortunately, Epson does not make software to "install" the printer to the router for Snow Leopard
- I re-installed the printer to the router using my wife's HP laptop and the original CD that came with the EPWF40.
- Follow the instructions on the CD for the install for "First Time" setting up the printer.
- After following the original instructions from the CD on her PC, the router assigned a new IP address to the printer, and the printer was "connected" to the router wirelessly
- Then, on my MBP running Snow Leopard, I ran the dmg file downloaded earlier from the Epson website.
- After running, go to the printer/fax preferences, click the "+" sign and add a new printer.
- As long as you are connected wirelessly to the router, under default, your mac should "find" the Epson printer. It is called something like "EPSON5A2EAA". There should be at least one, if not two options.
- One of the options should be "EPSON5A2EAA Bonjour" and the other "EPSON5A2EAA IP". Click on one, install it, and then go back and click on the other and install it (just to be sure).
- You will not be able to use the standalone Epson Apps installed from the DMG, however, the printer preferences for the epson, will be available through the printer preference boxes when you go through the system preferences.
It didn't make any sense at first for me either. Once I understood that:
- you can't install the printer from a Mac to your router
- after the printer is installed and linked with your router, your Mac can find it and use it
...I was able to complete the installation and have a fully functional wireless network printer.
Feel free to drop me a question. I'm just glad I was able to make it work.
-j

Sota Boy wrote:
I installed Snow Leopard but my Epson WorkForce 500 printer is not compatible. I saw an article about loading Rosetta and this would solve the problem. I can't find the article and I have never used Rosetta.
Actually, you have.
Rosetta was incorporated into both Tiger and Leopard. But it was invisible, of course. Snow Leopard is the first OS that offers the choice of whether to install it or not.
Any suggestions on how I find the recent article or make my printer work with Snow Leopard?
Don't know about the "recent article", but you can install Rosetta by inserting your Snow Leopard DVD and clicking on the Optional Installs package. When the configuration choice window comes up, just check Rosetta alone and carry on.
Good luck with it!
Archie

Can I connect apple tv and an Airport

I recently purchase an ATV2 & would like to play music over both my ATV & Air Port from iTunes. Can this be done?

Welcome to the Apple Community.
If you mean can you send audio from iTunes to the Apple TV and an Airport Express at the same time, then the answer is yes.
Select multiple speakers from the AirPlay selector in the bottom right corner and check each device from the list.

Does adding a second airport extreme slow the wifi speeds?

I get 17mbps from my airport base station hardwired to uverse router. On the new 5th gen extreme.used to extend network, speeds are 7mbps at best. is a second device incapable of the same bandwidth as the originating extreme?even when well within range?

My only issue is, i've not got the AE's on "bridge Mode"
That's quite an issue, since you only want to have one router handling DHCP and NAT on the network. You have two routers both trying to provide the same services if the AirPort Extreme is distributing IP addresses. Conflicts are inevitable. The AirPort Extreme needs to be in Bridge Mode.
I can't seem to put the AE back into the connection sharing option that says "distrubute a range of ip address"
This setting would be used only if your ISP has assigned multiple IP addresses to you....and the AirPort Extreme is the "main" router on the network.
"Share a public IP address" would be the setting to use.....if the Uverse router will tolerate another router on the network. Sometimes you can find a workaround, but then you have to put up with Double NAT errors and other unpredictable things on the network.
I used to be able to operate without bridge mode off the uverse router/modem but can't anymore.
Probably due to updates on both the Uverse and AirPort routers to prevent users from trying to run two routers on the same network.
Uverse routher which is impossible to figure out to reserve ip's etc for externetal devices.
Is this a Motorola router, or 2-Wire? Either should have online support for this type of basic router service.

I am running 10.8 and setup airport extreme to run music from my imac to my receiver in the other room. When I open sound from system preferences, I don't see an external device to choose, other then internal speakers. Any ideas?

I am running 10.8 and setup airport extreme to run music from my imac to my receiver in the other room. When I open sound from system preferences, I don't see an external device to choose, other then internal speakers. Any ideas?

Airport Express (the small Airport device, which is the only one with an audio connection) works through Airtunes, which only works with iTunes. The computer won't send ALL system sound to the Airport. If you actually want to send sound outside of iTunes, use Airfoil.
Matt

Airport extreme with USB hard drive permissions problem may be parallels

I cannot access my external hard drive because of some permission problem. I know because I can see this through the disk repair utility. I've attached my external hard drive to my airport extreme. It originally came up well and worked fine. Then it lost connection and now doesn't recognize my password. To confuse matters worse I have parallels installed. This might be where the password problem is as the mac wants to access as a guest and the parallels (windows MX) as my account name. It's all pretty complicated to explain. What I want to do now is just to forget the airport plan and reach my hard drive but it won't boot up even with airport off and a direct firewire connection. It does show up in disk repair utility but with permissions. How can I get to these permissions and drop them. What if they're windows permissions somehow? How can I get started.
Thanks

I have a very similar problem. I have a 2.8 GHz iMac with 2GB RAM and am using OS X v10.5.4, and an Airport Extreme (v7.3.2), both updated to latest firmware. I have a 500 GB TrekStor external HD connected to the AEBS via USB. The TrekStor HD was pre-formatted in FAT32 and is visible on my iMac's desktop and in Finder but I cannot transfer files to it or see files on it. When I drag and drop a file on the TrekStor, it sometimes seems to go well but then the file is not visible via Finder, and sometimes I get an "insufficient privileges" message. I repair permissions on the iMac's internal HD without any change. I am logged in as the admin. All assistance is much appreciated!

Apple TV and/or Airport extremely slow syncing - Unique or common problem?

Similar Messages

Maybe you are looking for