Apple TV and Remote  Problems using Airport Extreme

Had issues with power outage last summer just  recently got back to resetting airport extreme , and now my apple remote does not work evan after changing out battery's for my apple TV . The TV comes up trying to set date and time and never makes a connection, so Im unable or unaware of another way to get to the apple settings to check settings.

The fist problem is date and time.
Assuming this is not the first time you have used your Apple TV
You might try restarting the Apple TV by removing ALL the cables for 30 seconds.
Also try restarting the router.
If the problem persists, try a restore, you may want to try the previous procedures several times before doing this.
If this is a new Apple TV, it may also be that your network router is not allowing access to the timeserver, check that your router allows access over port 123
Once you get that sorted you can look to sort your remote.
Your Apple TV may have become paired with another remote. Hold the remote close to and pointed at the Apple TV, hold down the menu and Rewind buttons together for 6 seconds or until you see a broken chain icon on screen.

Similar Messages

  • File sharing problem between XP and MAC when using Airport Extreme

    I recently got a Time Machine to replace my flaky Linksys Wireless N router and since I've done that I can't connect to my PC running Windows XP and was able to before. I have made sure my firewall settings are correct and have gone through many different settings on Time Machine but still no luck.
    I have my PC directly connected via ethernet to the Time Machine and my Mac is wireless. I'm able to ping the IP address of the Mac from my PC but can't ping in the opposite way.
    Any suggestions would be greatly appreciated.
    Thanks!!

    btw the error is
    "Attempting to copy to the disk "Guy_s iPod" failed. The file name was invalid."
    and then it says
    "The iPod "Guy's iPod II" cannot be updated. The disk could not be read or written to."

  • Problems using Airport Extreme with tethered laptop to xbox.

    Here is the setup...
    I have the AEBS sitting in the other room about 20 feet away.
    Its plugged into the modem (motorola SURFboard) with a 2 foot Cat5 cable
    The Base station is running basically all default settings minus the wireless is set to use WPA/WPA2 and the ports for the xbox 360 are forwarded as well as a DHCP reservation for the xbox to insure its always on the ip with the ports forwarded.
    I have my computer in my room and im using it to bridge a connection to my xbox. (basically using the laptop as a wireless adapter) The xbox will connect to live and sign me in and everything. As soon as I start playing a game or something like photo party the connection will slowly start to drop out. If im in photo party i wont be able to see pictures and stuff and in games it boots me from the game. I need to be able to fix this. it doesnt make any sense because on my laptop it says im hitting 26Mbps and when i actually use my laptop it is able to download at up to speeds of 600 KB/s. (I do turn the downloads off when i try to play on the xbox.) SOMEBODY PLEASE HELP!!!

    Any torrents running on the PC? Any chance your isp is throttling your connection?

  • Network set up using airport extreme, time capsule and airport express

    I have searched for relevant answers but can only find different bits here and there.
    My set up is as follows:
    I have a Linksys wireless router running a stable wireless network for the other computer users in the house and wish to create an extended, additional network using airport extreme connected to the Linksys by ethernet to create the network and then time capsule close to my Mac Mini on my desktop and airport express at the other end of the house to try and extend the range of the network.
    I have been trying for 4 days to set this up but without success. I have tried all of the options mentioned in different posts, using WDS, extending a new network etc. I can get connection between the three devices but monitoring on iStumbler there appears to be little improvement in the strength of the signal, iStumbler also shows the time capsule dropping it's signal totally every 10 or so seconds for a few seconds and then I get a positive signal strength for another ten seconds or so.
    Can anyone help, it is driving me insane. I am a recent convert to apple computing and have been hugely impressed with all products until now. The claim that the set up of these wireless products is simple seems to be very exaggerated.
    I am happy to provide any relevant system or hardware information.
    Thanks in anticipation.

    I have an AirPort Extreme acting as a wireless base station, connected to a BT router by ethernet.
    Then the correct setting for Connection Sharing on the AirPort Extreme would be "Off (Bridge Mode)".
    If I set Connection Sharing to "Share a public IP address", I'm told that:  "The DCHP range you have entered conflicts with the WAN IP address of your Apple Wi-Fi base station"
    Exactly. You have two routers....The BT device and the AirPort Extreme in series with both of them trying to act as the "main" router when you configure the AirPort this way. That won't work.
    Only one can be the main router, and it must be the BT device in your setup. So, the AirPort Extreme....and any other AirPorts on your network must be setup to work in Bridge Mode to allow the network to operate correctly.

  • Big problem with Airport Extreme and Vivax Provider in Brazil

    Hello guys.
    I live in Brazil and I bought my Airport Extreme in a recent trip to USA.
    For some years I was a client of Telefonica and had an ADSL link, I had a D'Link G604T to do both the modem and router operation in the same box. I was happy with my connection of 1Mbps.
    In a recent promotion of Vivax I switched to a cable connection to have both TV and Internet at the same operator, my link now has 3Mbps.
    With this pack I also received free one RCA cable modem model DCM425B, it was installed fine in one computer only. Everything was fine my connection was faster the old one.
    So I went to install the Airport Extreme to make things even better.
    After I installed I went to see the web status of my modem, all parts were looking fine, but the modem could not see the computer. Bad sign.
    I talked to Vivax support people and apparently it was a problem with their network setup and they manage to make it right. My model now sees my computer.
    After that problem was solved I could not make AE to work with the modem, it had the green light and the setup looked fine, but I could not open any site. I tried to turn off my modem and AE, waited some minutes and turned on first my modem and after it was up I turned on AE. All lights looked fine but again no connection to any site.
    I called again the Vivax support center and they tried to help me but the don't know AE and they could not help me with all the details but said there was 2 10.x.x.x coming from my side. So I tried to use in bridge mode. I also selected the 192.x.x.x range instead of 10.x.x.x as default.
    After many setups and turn off and on again my connection is working but I have a big problem with wireless. If I turn it on I loose my connection, it seems that AE sends 2 equal ethernet address to Vivax and their network don't like it cutting me off.
    So my connection setup is like this:
    RCA Cable modem model DCM425B at 3Mbps using a 200.x.x.x ip
    Airport Extreme connected to a Mac and a Windows PC by wire using the 192.x.x.x range ip
    Wireless is off
    Bridge mode is on
    This the only way I could make it work.

    After a firmware update it worked fine.

  • Re : Apple TV doesn't connect to a Wi-Fi Broadband Internet Service using Airport Extreme

    Hi, using Airport Extreme (Airport Utility version 6.3.2, Internet :DHCP, Router mode : Off (Bridge)) with a Wi-Fi Broadband Internet service. My Desktop (iMac), Macbook,iPhone,iPad join the Airport Extreme Wirelessi network (WPA/WPA2 Personal) easily and Broadband ISP Login-page pops up with username & password options. However, in case of Apple TV (2nd Generation Software : 6.0.2 (6646.81.1)), it connects the Airport Extreme W-Fi network easily but no Broadband ISP Login-page pops up with username & password options. Even using the Ethernet connection of the said Wi-Fi Broadband Internet Service directly to the Apple TV, no internet network connects. Please help.

    There is no way you can handle login details with the ATV and there is probably no way you can do it with extreme in router mode either.. If you need to use a login name and password via a html screen then that is impossible in a device without html.
    But your newest addition confuses me.
    A slight correction in the question : the Broadband Internet Service isn't Wireless, but having Ethernet connection to the Airport Extreme.
    So how do your iphones pop up a login page.
    easily and Broadband ISP Login-page pops up with username & password options.
    The alternative method is to use a computer .. login to your service and use ICS through the computer to the ATV..
    See http://www.youtube.com/watch?v=0jJe_BkQMRc
    Or any site that shows how to route internet through a computer.

  • I have a Airbook and use airport extreme... it says my epson printer is OFFline and i cant seem to get it back ONline...have reinstalled software, help please!

    I have an Airbook and cannot get my printers to go back "online"  please help... i use airport extreme and i have an HP and an epson printer

    http://support.apple.com/kb/HT5824?viewlocale=en_US&locale=en_US

  • How do I use AirPort Extreme to be able print from my MacBook Pro AND a PC. If I connect printer into AirPort, I can only print on laptop. If printer is connected to PC hard drive, I can only print on desk top. How do I configure this to make both print?

    How do I use AirPort Extreme to be able print from my MacBook Pro AND a PC. If I connect printer into AirPort, I can only print on laptop. If printer is connected to PC hard drive, I can only print on desk top. How do I configure this to make both print?

    If you have not already done so, your chances will really improve if you....
    1) Connect the printer to the USB port on the AirPort Extreme
    2) Download and install Bonjour Print Services for Windows on the PC

  • I have a Apple Power Mac G5 Dual 2.3 GHz/6GB RAM/500GB HDD/Superdrive PowerPC Desktop and just bought an Airport Extreme card for it.  The card is recognized but will not see the in-house network.  This is a pre-intel computer.  Do I need an antennae?

    I have an Apple Power Mac G5 Dual 2.3 GHz/6GB RAM/500GB HDD/Superdrive PowerPC Desktop and just bought an Airport Extreme card for it.  The card is recognized but will not see the in-house network.  This is a pre-intel computer.  Do I need an additional antennae?   If so, which one because my research is confusing me about what is supposed to work with this computer.

    Please check out the following Apple Support article to see if your particular Power Mac model supports an external Wi-Fi antenna.

  • I currently use Airport Extreme Wanting to extend using another apple airport express

    How to set up Airport Express when already using Airport Extreme to extend range.

    Extending the range of an 802.11n network
    AirPort Utility makes it simple to extend the range of an 802.11n network if you are connecting another 802.11n base station. Connecting two 802.11n AirPort Extreme Base Stations greatly simplifies the WDS setup process.
    To extend the range of an 802.11n network:
    Open AirPort Utility and select the base station that will connect to the Internet.
    Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
    Click AirPort in the toolbar, and then click Wireless.
    Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
    Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
    Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
    Enter the network name and wireless password if necessary.
    Click Update to update the base station with new network settings.

  • I have a 4 gen Time Caps. and a 2nd Gen Airport Extreme I would like to extend my TC network to use the Extreme for the purpose of having internet available to my TV box wired.  Is this possible and how to I get them to work together?

    I have a 4 gen Time Caps. and a 2nd Gen Airport Extreme I would like to extend my TC network to use the Extreme for the purpose of having internet available to my TV box wired.  Is this possible and how to I get them to work together?
    How can I get my Time Cap (TC 4 gen) to recognise my 2gen Airport Extreem (AE)
    Frank

    Thanks for the info, this really helps.
    Power up the AirPort Extreme for a few minutes, then hold in the reset button on the back of the Extreme for 10 seconds and release. Allow a full minute for the Extreme to restart to a slow, blinking amber light.
    It might be possible to use wireless to configure the Extreme, but I recommend using a wired connection. Temporarily, connect an Ethernet cable from your Mac to one of the LAN <-> ports on the Extreme.
    Click the AirPort icon at the top of the Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear. Just below that, click on  AirPort Extreme.
    The illustration below shows an AirPort Express. You will see AirPort Extreme on your screen.
    AirPort Setup will open up automatically and take a minute to analyze the network, then announce that the Extreme will be configured to extend the Time Capsule network.
    Enter a device name that you want to use for the Extreme and click Next
    Wait a minute while AirPort Setup configures things for you. When you see the message of Setup Complete, click Done.
    You can disconnect the Ethernet cable that you used for the set up now. Things should be working. The Extreme is providing additional wireless coverage the the Ethernet ports are enabled. You can connect to any port that you want since they all operate the same in this type of setup.

  • Use 2nd gen apple tv and remote control app on iphones and ipad.  We can control some functions on the apple tv but unable to purchase, access such controls as reset, restart, turn off home sharing, etc.  Home sharing stuck on old apple ID. Please help.

    Use 2nd gen apple tv and remote control app on iphones and ipad.  We can control some functions on the apple tv but unable to purchase, access such controls as reset, restart, turn off home sharing, etc.  Home sharing stuck on old apple ID. Please help.

    That is why I said to restore via iTunes, did you check the link?
    This will put it back to factory settings and you can set it up with the new ID once you reconnect with your HDTV. This is not done via ethernet, as per the link you need to connect to the computer via micro usb. You cannot bypass home sharing.
    FYI: An Apple ID cannot be deleted so the old one would still exist (even if you no longer use the email account it is associated with).

  • Airport Extreme: Internet working when directly from modem to computer, but not when using airport extreme. i have hit the reset pin and now do not know what to do.

    Using Airport Extreme:
    - Internet working when directly from modem to computer
    - Internet NOT working when modem is connected to AE
    - Internet NOT working when modem is connected to AE and AE is connected to computer
    - I have hit the reset pin
    Now what do I do?
    (in advance - lots of love to anyone who helps out)

    What sort of Internet connection do you have and who is your Internet Service Provider?
    What is the make and model number of your modem?

  • Using Airport Extreme with Linksys Router/Modem

    I was just told that my Mac mini is excruiatingly slow on the internet because I am using a Linksys router with Xfinity and that Airport Extreme will be much faster.  And that I should plug Airport Extreme into the modem.  When I checked, I don't have a separate modem.  My Linksys is a combined router/modem.    What should I do?  Do I plug the Airport Extreme into the Linksys box, or do I get a completely different modem that is only a modem?  And, if I plug Airport Extreme into the Linksys box, how do I configure the network for Airport Extreme, and what else do I need to do?   All help greatlly appreciated...I can barely get onto the Apple website!

    When I signed up with Xfinity one of the stipulations was that they would not install a router/modem but only a modem. I had heard of problems with their router/modem and I didn't want to go down that path.
    I don't but you mighht be able to get them to change out your router/modem for a modem. I would start there by asking them.
    Allan

  • HT1218 why is streaming to my TV slowing to .4 mbps from 8.ombps while watching a netflix movie? this has become a problem in the last 2 months. This also happens on another TV but not concurrently.. Is it a problem with "airport extreme" or with the IP s

    why is streaming to my sony TV slowing to .4 mbps from 8.ombps while watching a netflix movie? this has become a problem in the last 2 months. This also happens on another TV but not concurrently.. Is it a problem with "airport extreme" or with the IP service? Airport extreme software is up to date.
    please advise
    Michaelgfrommet

    For what it's worth, you posted this in 2011, and here in 2014 I am still having this same issue. Over the last two days, I have had to unlock my apple account 8 times. I didn't get any new devices. I haven't initiated a password reset. I didn't forget my password. I set up two factor authentication and have been able to do the unlocking with the key and using a code sent to one of my devices. 
    That all works.
    It's this having to unlock my account every time I go to use any of my devices. And I have many: iMac, iPad, iPad2, iPad mini, iPhone 5s, iPod touch (daughter), and my old iPhone 4 being used as an ipod touch now.  They are all synced, and all was working just fine.
    I have initiated an incident with Apple (again) but I know they are just going to suggest I change my Apple ID. It's a simple one, and one that I am sure others think is theirs. I don't want to change it. I shouldn't have to. Apple should be able to tell me who is trying to use it, or at least from where.
    Thanks for listening,
    Melissa

Maybe you are looking for