Apple TV, Hulu Plus, and Factory Restore issues.

I have a Apple TV 3rd gen I believe. A couple weeks ago Hulu Plus stopped playing videos. I tried logging out and back in and when that didn't work I tried doing a Restore on the apple tv, but everytime it gets to a certain point it fails and tells me to try again. I'm at a loss of what to do. Please help.

muna0001 wrote:
Hulu has their app ready for apple tv but apple blocked them because they thought it competes to much with iTunes. By that logic I doubt apple will ever allow it on apple tv.
Are you talking about this app?

Similar Messages

  • I am having trouble downloading anything from hulu plus and netflix on my Apple TV. It says error has occurred during download try again later.  I have unplugged and re plugged and nothing has changed

    I am having trouble downloading anything from hulu plus and netflix on my Apple TV. It says error has occurred during download try again later.  I have unplugged and re plugged and nothing has changed

    What is your connection via speedtest.net ?
    Check istumbler or netstumbler to verify network interference
    Make sure DNS is set correctly (settings - general - network - configure DNS - automatic)

  • I have i phone 4 and i didnt remove my i tune id and passward and i forgotton both and factory restored my i phone now it dosn't start plz help me ..

    i have i phone 4 and i didnt remove my i tune id and passward and i forgotton both and factory restored my i phone now it dosn't start plz help me ..

    Seriously, you can't remember either your Apple ID or Password? Well, since you're logged in here, you obviously can remember that Apple ID/Password.
    Regardless, I suggest you remember this info, 'cause if you can't, all you'll own is a paperweight. And no, Apple can't/won't help you.

  • Wipe and factory restore without discs

    Hi can i do wipe and factory restore my MBA without the discs , i have them some where but no idea where

    We did the same with my wife's MacBook Air before giving it to our daughter, but it is not necessary to erase the drive. Create an account for your wife, give her Administrator privileges, then log into her account and delete your account. Everything you did on the MacBook Air will be gone.
    Presumably, your MacBook Air is working well and your intent to 'wipe' it is not therapeutic, i.e., a clean install of the system software to remedy a software problem. If that is what you intend, then you will need to find your discs.

  • Hulu plus, and netflix not working on Apple TV Please help

    Hulu plus, netflix and itunes store wont open on my apple tv.  I cheked the internet connection and apple tv says it is conceted to my wi-fi.  The internet and hulu and netflix will all work on my other devices in my home but just keep getting can not access at this time messages from the Apple TV- We dont have cable so it is really bad that the apple tv stoped working can anyone help! please,

    Power cycle the ATV and router.
    If the issue persists, ensure that the the DNS settings on the ATV are set to automatic.
    Also, if using a proxy or VPN to connect to the Internet, try bypassing.

  • X220 factory restore issue with Rescue and Recovery

    I have X220 which I enjoyed very much for the last one year. Warranty is just expired and unfortunately the system starts act crazy. I decided to reformat and go back to factory setting stage by using Rescue and Recovery. I could get to the Full Restore and could click full factory restore. The system ask me to restart but instead reformat the HD, the previous OS kicks in and reboot as previous setting. Please help!!!

    Are you sure Q: partition is absolutely empty? Normally .WIM files on partition Q: are stored in hidden directory FactoryRecovery.
    Check out Lenovo Factory Recovery Discs within Control Panel for creating factory image media.
    x220 | i5-2520m | Intel ssd 320 series | Gobi 2000 3G GPS | WiFi
    x220 | i5-2520m | hdd 320 | Intel msata ssd 310 series | 3G GPS | WiFi
    Do it well, worse becomes itself
    Русскоязычное Сообщество   English Community   Deutsche Community   Comunidad en Español

  • Selling my iPad 2, steps involved to save my apps and factory restore it?

    Hey,
    I'm selling my iPad 2 to finance iPad 3, can someone please explain what should I do so that all my apps/data/photos are backed up to my iTunes, and a way to factory restore it so that the new owner will have no access to my personal stuff?
    Thanks in advance!

    Transfer all purchases into iTunes, backup the iPad and then sync with iTunes.
    Transfer purchases.
    http://support.apple.com/kb/HT1848
    How to backup
    http://support.apple.com/kb/HT1766
    When you are ready to sell the iPad - erase it - Settings>General>Reset> Erase all content and settings.
    Connect the new iPad to iTunes and when given the option during activation - restore from the backup of the old iPad and then sync with iTunes

  • Apple TV HULU plus

    I have an older second generation apple tv purchased Dec 11, but am pretty sure that I should be able to use Hulu plus on mine. But there is no option for it on my main menu screen. What am I missing? Should I do a software up date? Will that fix it?

    Where are you located? This is US only. Make sure location is set correctly via settings. Reboot device, router.

  • MSI 7220 (Diamond Plus) and 7800GT/7900GT issue

    So I bought the Diamond Plus and the MSI NX7800GT a few weeks ago.  Everything set up fine, no problems.  I start playing some games, mostly City of Heroes/Villains, and I notice a graphics issue.  Objects in the distance are "Z-fighting".  It looks as if the Z-buffer's precision is low.  I have tried AquaMark3 and I get the same issue, low z-buffer precision.  So I sent the video card back, got an EVGA 7900GT.  I still have the same exact issue, which never gets better/worse, the problem is always exactly the same.  I have tried the card in both PCIe 16x slots and have done a full RAM test.  Bios is 3.0A (no difference with 1.0 or 1.16)
    Can anyone out there with this Mobo and a 7800GT or 7900GT run AquaMark3 (http://download.guru3d.com/aquamark3/) in demo mode.  The demo starts out following a ship, in a few seconds you go up and over a tiny hill and see a vast scene in front of you.  Off in the distance, do you see geometry intersecting in an odd way?
    I've not noticed any problems in Quake4, Doom3 or 3Dmark, so maybe it's a DirectX only issue.  This is extremely frustrating, because I can't imagine what the problem could be.  System is completely stable and I have no other problems.
    Thanks in advance if anyone out there tries the demo

    Quote from: Grouse on 13-April-06, 00:53:42
    OI,
    As you can see from my sig i have a similar set up.  I use antec PSU. The issues your talking about are Likely due to a combination of things not Just one.
    First of all are you setting your nvid drivers to the game you are using instead of global settings.
    Also what are your amp ratings on your PSU.
    Also what are running in your back ground.  How many processes?
    Have you defragged that drive since your last install?
    Have you run dxdiag?
    are you using the latest dx version?  One came out just recently.
    I appreciate all the feedback guys, and as far as these questions, I have tried on 2 clean installs (winxp pro, and winxp x64), and have the same problem.  Nothing else running whatsoever, everything updated, etc.  It's got to be a hardware issue, and since it's a graphics problem that I've experienced with 2 cards, you guys must be right, it must not be getting enough power.  I chose this PSU because Tom's Hardware used it in their test setup with this board (didn't realize it was such a sensative issue).  I'll keep messing with it for another day or so.  I'll be quite happy if it's just the PSU and I don't have to send the mobo in for replacement. 
    Thanks again

  • Fusion drive and backup/restore issues

    Hi,
    since I installed a fusion drive on my early 2008 iMac, consisting of an internal 256GB SSD and an (external FW800) 320GB hard disk, I occassionally run into trouble when system updates are pending. In the past, at worst the time machine backup couldn't be restored and I had to reformat and reinstall the system from scratch - which is not really comfortable!
    Currently, running Mountain Lion, when I try to select the startup disk, it complains that Boot-Caches on the Boot-Helper-Partition cannot be created. Nevertheless the system starts fine (and runs fast ;-).
    Before upgrading to Mavericks, I would like to know
         - if someone else ran into similar problems with fusion drives, when updating/upgrading system software.
         - Is it normal that a Time Machine backup cannot be (completely) restore a Fusion drive?
    Yes, I know that having the harddisk part of a fusion drive externally is not recommended/supported by Apple - and my Mac is nearly 6 years old, but that would not explain why system updates/restores nearly always fail and sometimes the Time Machine backup drive has a broken file system (needed reformatting)! And I always checked the disks with Disk Utility prior to updating...
    Any comments are appreciated.

    You can file feedback here. The more who file the more the faster the issues may be fixed.
    Also you shoud look on the CCC forums.

  • Apple TV, My Receiver, and Potential HDMI Issues...?

    Hey all
    Okay, I'm about to bite the bullet and snag myself an Apple TV, but I have a couple of wicked-fast questions that I think I know the answers to — but I'd like confirmation.
    1. If I get an Apple TV, I want to run it through my main receiver, so my plan would be to connect the ATV HDMI to my receiver like all my other components (my Onkyo has a single HDMI out, BTW). This will treat the ATV like all my other components as far as sound through my mains, etc.
    Am I correct to assume this will work? Apple's docs seem to want you to connect directly to your TV...
    2. I have heard that upon upgrading to the v3 software that was just released, some people are having issues with the ATV recognizing when the receiver has switched to it, making an ATV restart necessary. Anyone having that problem? I feel it may be because these people are using legacy receivers...?
    THANKS!
    Maury

    {quote:title=Winston Churchill wrote:}
    I've got a brand new Denon AVR 4810Ci receiver that is current to the HDMI standard. I've got no other issues with HDMI sources other than the AppleTV.
    The problem is that the tv currently meets the HDMI standard too.
    So it's a little more complicated than just being tested to receive certification.{quote}
    Which must mean software / firmware. I also have 2 other devices passed through my receiver, connected by HDMI, without issue. Nothing on my set-up, software or hardware wise (both box and cable), has changed for about 2 years except for the various Apple TV updates. No problems with v1 or v2, yet v3.....

  • Apple Tv 2, NetFlix and a new issue

    I am on the road, my Apple TV 2 and I are in Panama. Netflix has just, today, started service in Panama. I can access my account with my laptop without any issues. Apple Tv allows me to login, select programming and when I press paly I get this message.
    Your device must be updated to play instantly from Netflix. Visitmanufacturer's website or devices netflix.com / NRD for more information."
    Netflix says call Apple, they have no clue. SO I am here, anyone have a clue?

    Lee,
    I'm in the Dominican Republic and having the same issue.  Netflix will not work on my Apple TV 2, iPad or iPhone.  Looks like Netflix needs to update it's Apps.

  • Drag and Drop Restore Issue

    The hard drive on my first generation MacBook Air failed, and I had it replaced by Apple. They reinstalled all of the Apple software that was on my old drive. Now I'm trying to restore using a sparsebundle that I keep on an external drive. That part is no problem. The problem arises when I try to drag the destination drive, the new hard drive, to the Destination area. It won't go. Any help would be appreciate.

    You can't use the Restore tab of Disk Utility to restore a Time Machine backup.
    See #14 in [Time Machine - Frequently Asked Questions|http://web.me.com/pondini/Time_Machine/FAQ.html] (or use the link in *User Tips* at the top of this forum).

  • Apple logo appears only and cant restore in recovery mode

    iphone4 wont work tried everything. the only thing that it shows is the appl logo and whe i put it into recovery mode it wont let me restore or update

    Put the Phone in DFU and then try to restore
    Step 1. Turn off your iPhone.
    Step 2. Hold down the power and home button.
    Step 3. When you see the Apple logo, release the power button but continue holding the home button down.
    Step 4. Open iTunes and wait for it to tell you that its in restore mode.
    Alternative Method:
    Step 1. Connect iphone to USB then listen to the sound when it connect and disconnect.
    Step 2. Hold the home and power buttons until hear the disconnect sound then release power button.
    Step 3. Wait until you hear another sound then release home button.

  • Shorewall 4.0.9 and iptables-restore issues

    Hi,
    I installed Arch Linux on my home router (old Pentium 3 PC) a long time ago. I used Shorewall 3.x, worked really nicely! However, I wanted to try out FreeBSD as a router so I installed that earlier, then I figured I didn't want to bother re-learning everything so I installed Arch again, but this time I would use Shorewall 4.x.
    The Shorewall packages were outdated, so I modified them myself using ABS (shorewall[-perl]: 4.0.6, 4.0.5 -> 4.0.9) and installed them. So far so good... I configure shorewall using the two interfaces example and then I start it using "shorewall start":
    Preparing iptables-restore input...
    Running /usr/sbin/iptables-restore...
    iptables-restore v1.3.8: Couldn't load target `Reject'
    Error occurred at line: 64
    Try `iptables-restore -h' or 'iptables-restore --help' for more information.
    ERROR: iptables-restore Failed. Input is in /var/lib/shorewall/.iptables-restore-input
    I talked to the shorewall author and he tried the .iptables-restore-input on his own computer and said it was just fine, which makes me think it's an Arch Linux issue. So I installed AL in VMware and it was just fine with the same configuration! I have no idea what's going on.

    Hi,
    I installed Arch Linux on my home router (old Pentium 3 PC) a long time ago. I used Shorewall 3.x, worked really nicely! However, I wanted to try out FreeBSD as a router so I installed that earlier, then I figured I didn't want to bother re-learning everything so I installed Arch again, but this time I would use Shorewall 4.x.
    The Shorewall packages were outdated, so I modified them myself using ABS (shorewall[-perl]: 4.0.6, 4.0.5 -> 4.0.9) and installed them. So far so good... I configure shorewall using the two interfaces example and then I start it using "shorewall start":
    Preparing iptables-restore input...
    Running /usr/sbin/iptables-restore...
    iptables-restore v1.3.8: Couldn't load target `Reject'
    Error occurred at line: 64
    Try `iptables-restore -h' or 'iptables-restore --help' for more information.
    ERROR: iptables-restore Failed. Input is in /var/lib/shorewall/.iptables-restore-input
    I talked to the shorewall author and he tried the .iptables-restore-input on his own computer and said it was just fine, which makes me think it's an Arch Linux issue. So I installed AL in VMware and it was just fine with the same configuration! I have no idea what's going on.

Maybe you are looking for