Apple TV-Internet Connection?

Hi.
I use O2 mobile broadband so I won't be able to connect Apple TV to the internet(as far as i know).Is it still possible to just download movies off iTunes on my Mac and watch them on my TV without having Apple TV connected to the internet?
Help would be much appreciated.
Thank you,
Thomas.

Have you tried enabling internet sharing.
http://docs.info.apple.com/article.html?path=Mac/10.5/en/8156.html

Similar Messages

  • Apple Mail internet connection problem

    i  am able to download pages, check on icloud my email, etc. but I am unable to download or send mail via apple mail.
    is there a specific reason for that?
    I am quite often using public libraries and it's mainly there the problem exists - in some it's impossible, in others (after a lot of trying) it is possible.
    Is there any solution?
    Mark

    I would recommend that you do the following as a minimum:
    Power-down the modem, AirPort base station, and computer(s).
    Disconnect the AirPort base station from the Internet broadband modem.
    While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
    After the base station resets, go ahead and power it back down.
    Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
    Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
    Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
    Power-up your computer(s).
    In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

  • "Share A Public IP address" Apple Utility Internet Connection

    After following advice in another thread I've gotten rid of some home network problems that started dogging me last Friday. I got rid of a Netgear router that was evidently causing IP problems with the Extreme.
    I've had to re-set the Extreme and now I am wondering if I want to under the Internet Connection Tab of the Airport Utility set "Connection Sharing" to "Share a public IP address"?
    I am now using the Extreme (N only) as a router, and have it feeding an Express(G only), a Netgear switch and two hard wired/Ethernet connected desktops.
    Thanks for any advice is one way or the other more secure from the outside world. I do have the Apple Firewall on my computer on.

    Unfortunately, you will need to "hard reset" your AirPort Express to clear out the old and conflicting settings on the device.
    To do that, hold in the reset button until the amber light begins to blink more quickly and keep holding another 4-5 seconds when this occurs, then release the reset button and the AirPort Express will restart. You should have a slow blinking amber light after 40-45 seconds. That is your signal that the Express can be reconfigured as you had it originally.
    Since you are effectively trying to run two routers, both handling DHCP on your network, you may need to keep an eye on things. Even if you avoid the IP address conflicts, you will have to deal with a Double NAT error on your network, which can slow communications between devices (and the Internet).

  • Share Apple TV Internet connection over ethernet?

    I want to share my internet that I'm getting wireless through my Apple TV with my PS3 (which isn't wifi capable). Problem is 1) I don't know where I could turn sharing on and 2) when I plug an ethernet cable in, the wifi disables. Is there a solution that doesn't involve extensive hacking? Much Thanks!
    Bob

    Short of installing a third wireless router as a relay, I was hoping for a more efficient solution. Thanks!
    You don't necessarily need another router. If you can run an ethernet cable from your router to a point closer to the basement, a simple wireless access point connected to the router by cable would be enough to boost the wi-fi range.

  • How to use my iphone internet connection on my laptop

    How to use my apple iphone internet connection on my laptop

    Read through this article:
    http://support.apple.com/kb/HT4517

  • When streaming a movie with the new Apple TV, and using a DSL Internet connection, all audio sound works, e.g., the music track, but the audio track with the actor's voices, does not work. What can I do?

    When streaming a movie with the new Apple TV, and using a DSL Internet connection, all audio sound works, e.g., the music track, but the audio track with the actor's voices, does not work. What can I do?

    Hi Brian,
    Thanks restoring and restarting didn't fix my problem - i have started it fresh and still it doesn't work. Basically I press ONCE on the remote, after the machine has not had any commands for 10 minutes, and the cursor skips from one end of the menu to the other - so I can't choose network or update software etc - I sometimes manage to stop it randomly in the middle of the menu if I press on a command in the middle of the cursor skipping all the menu steps...not sure what the problem is but I have basically not used my brand new apple tv since I bought it for that reason! I should call Apple support I suppose! grrrr hate wasting time with stuff like this!
    Thanks for your help though!
    Pernille

  • I can't get FaceTime or iMessage to connect, I enter valid password (tested and works for Apple account) and it won't connect. I have checked all settings, upgrades iOS to 8.3 rebooted, changed Apple acount PW still wont connect. My internet connecti

    I can't get FaceTime or iMessage to connect, I enter valid password (tested and works for Apple account) and it won't connect. I have checked all settings, upgrades iOS to 8.3 rebooted, changed Apple acount PW still wont connect. My internet connection is fine Safari works and I can access all sites. I have an iPad 2. Any help on this will be greatly appreciate.  iPad 2, iOS 8.3

    This is an ongoing problem as you will see by searching the forum. 
    Out of curiosity, do you have 2 step verification enabled?  It was recently extended to include iMessage & FaceTime & I'm wondering if it might be causing some of the issues that some users are experiencing.

  • TS3638 i have an internet connection but when i open app store it shows error message "cannot connect to app store".when i try to sign in with my valid apple ID and password it says "connection failed".i tried keychain access settings but it did not help.

    i have an internet connection but when i open app store it shows error message "cannot connect to app store".when i try to sign in with my valid apple ID and password it says "connection failed".i tried keychain access settings but it did not help.please help me!!

    Open Sysem Preferences from your Apple () menu top left in your screen then select the Firewall tab.
    Make sure the Firewall is turned off.

  • How can I use Apple TV with iPhone 4S and no home Internet connection?

    Ok here is the situation.  I'm at my grandparents house where I have the following setup;
    NO home Internet connection
    iPhone 4S
    Verizon carrier with unlimited data plan
    Apple TV (I believe it's the latest one)
    Lynksys router
    What I would like to do is stream Netflix, HBO GO, or You Tube and put it on my grandparent's tv where I have the Apple TV hooked up.
    I thought it wouldn't be a problem however I can't figure out how to be on the same network from the router and receive 3G data at the same time.
    Is it possible to do what I want with this setup?  If so how?
    Thanks

    I think I worked out a solution given my equipment.  I was looking around on other forums and I found the following post concerning the ability for iPhone 4S to be on 3G and wifi simultaneously.
    "I know this thread is old and op may have discovered the answer already. However, I am posting this just in case someone else might be looking for a solution.
    The solution does not require any additional software nor require a jailbreak.
    All you need to accomplish this is already built into every iPhone and iPad with 3G.
    Connect to your wifi and write down the IP address your router assigned you. Then, select static tab instead of DHCP and fill in the IP address your DHCP server assigned to your iPad. Next, fill in the subnet mask but leave the rest of the fields empty.
    You now have access to your wifi as well as 3G.
    I ran into this issue when I wanted to use live traffic using 3G for my iPad's GPS and still connect to my GoFlex Satellite using wifi. It works extremely well."
    AFter configuring my phone to the router, as mentioned above, I connected my Apple TV to the same router.  Using the mirroring option I was able to airplay Netflix, You Tube and Flixster flawlessly from my phone to the big screen.  Direct TV and HBO GO did not work however. 
    I Then tried to access items directly from Apple TV thinking that it could use the data from my phone.  I was wrong.  So all in all I'm able to stream about half of my movie entertainment applications given my situation.  I'm pleased.

  • My Apple Tv is connecting to the Wifi network but is not connect to the internet.  So when I look for it on my Airplay it doesn't come up.  I have 3 other ones already working on the network and they are all fine.

    My apple TV is finding and connecting to the Wifi network but then says it is not connected to the internet and then I cannot find it on the iPad through airplay.  I don't want it connected to the internet (as in www.) because for the use I have I only need to use the Apple tvs locally in a sports hall as scoreboards.  I have 3 others working on the same router and they are working fine (as of yesterday)
    On my screen I see (obviously not written like this)
    network connect- yes
    signal strength- fine
    Ip address- fine
    DCN- fine
    Activation- Failed
    This is the only negative I can find and the statement that the Apple TV has connected to the wifi but is not connected to the internet.
    Where has it gone wrong for me. Please help

    It is not properly connected to the network.
    Make sure location is set correctly
    DNS should be on auto (settings - general - network)
    Try ethernet
    Signal strength on device won't account for issues, you would need a network report from istumbler, netstumbler or similar. This will show accurate signal strength along with noise and nearby networks

  • HT201335 Can i use airplay with the apple tv and airport express without an internet connection? Basically Set it up as a closed network?

    I was told I could set a local network with the airport express, apple Tv, and my iPad to stream videos or pictures to a TV for a presentation.
    No internet connection is available at the location.
    Is that possible? Or do I need to access itunes homeshare with an internet connection to make this work?
    I've set it up at home where I have an internet connection and it works fine but I want to move the setup to my church for a class. The data I'm using is stored on my ipad.
    I know I can do this wired with the HDMI adapter but would like to do it wireless.
    Thanks for any help!

    Ok so we now have a solution to the problem.   A friend of mine came round to work this out with me last night and we were able to get it working, but it is not as easy as I had hoped.  Fisrtly we plugged the airport express into my router using the ethernet cable  (for this I am using an Airport Express Base Station") and in airport utilities selected the airport express.  In edit, we then gave the airport express a new range of IP address which did not conflict with any of the other applications that I have already assigned.  We also named the Airport Express with a distinguishable name.  We then waited for the changes to be registered then unplugged the Airport Express from the router.  I then plugged my AppleTV via HDMI into a tv to test it and selected the new wifi network with the new Airport Express distinguishable name.  I was able to watch a video that I have on my ipad directly on my tv without being connected to the internet, and was able to play Airplay presentations.
    No the easiest solution, and certainly not something that anyone at Apple has talked me through in my lengthy conversations with them at Applecare. 
    Hope this helps.

  • Why does my connection to Apple store constantly fail even though I have good internet connectivity to all non-apple apps?

    Hi.
    All of a sudden my IOS devices are having difficulty accessing all of my Apple-store controlled apps and purchases when using my home network, even though it is a really fast network and my other devices work perfectly. Spotify, YouTube and Netflix and all apps that don't rely on Apple purchases are working perfectly on my iPad and ipod, and I have fast internet speed and perfect connectivity on all my other devices.
    But when I go to Newsstand or iTunes Store for example I get the message 'can't connect to Apple server' or 'you are not connected to wifi' even though all non-Apple apps are connecting perfectly on the same device. I have tried all the usual reboot, reset solutions and nothing seems to resolve this. My software is up to date. My iPod and iPad are working perfectly when I use another network. My home network is working perfectly for everything else.
    Any ideas?

    Sorry for bad English and typos, I wrote it quickly.

  • Apple programs will not recognize Internet connection after Tiger upgrade

    In January, I posted the question below. I wanted to update it, but this site has archived it and will not allow responses. In the hope that I may help someone else, I am repeating my question, now that I have the answer.
    ===============================================
    ORIGINAL PROBLEM
    Last week, I upgraded from 10.3.9 to Tiger. Ever since then, I have had trouble using Apple's programs that require internet usage: Safari, iTunes, Software Update, etc. All of these programs think I am not connected to the Internet. But I am; I can use Netscape, Internet Explorer, and other non-Apple programs on the web.
    Furthermore, it's not consistent. Sometimes Safari will recognize the connection. I'll be using Safari, looking up websites, when suddenly it will quit connecting, giving me the message, "Cannot connect to the server," no matter what server it is, even apple.com (so I have to use Netscape to access my .Mac and this Support screen).
    How can I resolve this?
    ==============================================
    The problem was that my Earthlink Access software was setting a proxy on my connection. Netscape & Firefox worked because they ignore any proxies; the Apple programs (plus Shiira and Internet Explorer) didn't connect because they use the proxies.
    Why did it sometimes work? Well, if I first used Safari to go to a secure website of my bank, somehow that opened up the connection and then I could continue to use the Internet and Internet based programs like iTunes and widgets. However, if I tried to use an Internet-based program before going to the secure site, then it wouldn't work.
    After months of phone calls and e-mails and sending data packets and all such stuff with Apple Care, they finally stumbled upon this answer: Uncheck the proxy box. And that did it. At first I had to uncheck it every time I started up the computer, but now it stays unchecked and I can use my Apple programs with no trouble.
    I just wanted to share this with you in case you also had trouble with Internet connections after upgrading to Tiger, because I did see several other people had this same trouble.
    Movable flat-screen iMac G4   Mac OS X (10.4.6)   1.25Ghz processor, 256 MB memory (DDR SDRAM)

    For the record, could you state each Proxy box you ended up unchecking please? I'll attempt to submit a user tip with credit to you for finding this solution.

  • Internet Connection - Your Apple wireless device does not have a valid IP.

    I just bought an Apple TimeCapsule and set it up normally, following instructions to my Arris cable network on the Videotron provider here in Quebec, Canada. The TimeCapsule did appear as a wireless device on my MacBook Pro (after updating the AirPort software from the provided CD - as was instructed). I went through the whole installation process to obtain at the end this error:
    Internet Connection - Your Apple wireless device does not have a valid IP.
    The only provided instructions were to check the cable and then contact your Internet provider. Well it seems clear to me that if I contact my provider and say that the internet connection works fine directly on my computer, also fine through my "normal" wireless router but not with my new TimeCapsule, I won't get much of a response.
    After a lot of research, a friend indicated the solution in my case.
    You have to really reset the cable modem to convince it to start giving out IPs again.
    To do this:
    1. Unplug your TimeCapsule (possibly you might have to reset to factory defaults - see the documentation)
    2. Unplug your cable modem
    3. Reset your cable modem by pressing the reset button with a pen (or something) for several seconds.
    4. Plug your cable modem back in and let it reboot/restart - until the lights are back on.
    5. Plug in your TimeCapsule
    Everything should now work and you can restart your AirPort set-up on your Mac.
    Good luck!

    My ISP is AOL.  The service is DSL via a broadband modem.  Somewhere during the setup process there appears to be a communicatiosn issue between the Airport Extreme Base Station and the DSL modem.  When I hook the DSL modem directly to my iMac I can connect to the internet without any issues. 
    I tried the factory reset and the DSL modem reboot process described in other posts and seemed very close to success...until the internet setup step.  That is where this issue first presented itself.

  • How do i wipe my old phone if it can no longer connect to the internet? I enter my passcode and apple id, but 'verification fails' as there is no internet connection???

    how do i wipe my old phone if it can no longer connect to the internet? I enter my passcode and apple id, but 'verification fails' as there is no internet connection???

    Hi, JTCW33. 
    Thank you for visiting Apple Support Communities. 
    If you still have possession of the iPhone you wish to wipe, here are a couple articles that will walk you through the process. 
    What to do before selling or giving away your iPhone, iPad, or iPod touch
    http://support.apple.com/kb/HT5661
    iOS: Unable to update or restore
    http://support.apple.com/kb/HT1808
    If you no longer have access to your device, it will need to be connected to the Internet in order to remote wipe the device. 
    iCloud: Erase your device
    http://support.apple.com/kb/ph2701
    Cheers,
    Jason H. 

Maybe you are looking for

  • Error messages 2502 and 2503 when trying to install itunes to my computer

    I have attempted to download itunes to my windows 8 operating system computer and it keeps telling me that it has encountered and unexpected error installing this package.  This may indicate a problem with this package.  The error messages are 2502 a

  • "sort by" in Preview

    Is there a way to get Preview to automatically sort multiple images by filename? I had used Preview on my PowerBook G4 for years with no problems viewing images (OS X 10.3.x), but now that I've got a new MacIntel with 10.4.7, whenever I open multiple

  • Sun T3B T3+ maximum volume size (over two TeraBytes)?

    I have a T3+ array that I have upgraded with 400GB FATA drives. When I did it I had firmware release 3.1.6. The downside was that I could include only a max of 6 drives in a RAID 5, because going over 2TB (2.45TB with 7 disks) the volume so created w

  • Valuation area HDQF not yet productive with material ledger

    Dear all, When i PGI, there is an error: Valuation area HDQF not yet productive with material ledger. Pls help me to resolved. Thanks & Regards,

  • Edit Date updated for whole catalog (how to view edit date?)

    I suddenly found out that my publish service that exports newly edited photos suddenly contained all my photos, and I have no idea how that happened. It seems the Edit Date has been changed, but I can not find any way to view the date, so it's diffic