Apple TV loses picture output and status light flashes rapidly after 5 minutes hooked up via HDMI - DVI cable
Apple TV connected to a 2005 50" plasma monitor with DVI input via belekin HDMI to DVI cable. Unit worked perfectly long enough to get it connected to the wireless network and begin the itunes registration process when there was a loss of signal message on the screen from the monitor and the Apple TV status light flashed rapidly and continuously. Reset and reboot yeilded flashing rapid status light and no output detected from the monitor. I contacted support online and was told to return the unit to the apple store. I returned home with another brand new apple tv and connected it in the same manner with exactly the same results. Is there something with the HDMI - DVI interface that is causing this? Are there known issues with the HDMI - DVI connection to Apple TV with older plasma monitors?
The Apple TV doesn't actually support DVI. Some have managed to get it to work others have had varying issues with it.
Similar Messages
-
3 status lights flash rapidly only after unplugging it stop
Whenever I use Airport setup assistant to make changes to my existing setting, and when the base station should be restarted it stops sending a signal and then all three status lights flash rapidly and also simultaneously. This is a replacement base station as the previous had its wan port fried. When it was first plugged in it gave this same problem. Only after plugging out the power chord and waiting for say 1 minute, then plugging it back in did the flashing stop and the base station started sending a signal again. This also occurred during the first set up using airport admin utility. It hasnt happened since (when using admin utility) but continues to happen when I use airport setup assistant. Is it sumthing I should be worried about?
Sounds like your Airport Base Station is operating just fine - I wouldn't worry about it.
-
ITunes wont open and status light flashs orange. PLEASE HELP!!
I turned on my computer and plugged it in after loging into Windows XP. iTunes wouldnt open and when I tryed to click it open it wouldnt work. I then safely took out my Shuffle and restarted my computer. Then repented the above process and no luck. Can someone please help me?
Try the new shuffle reset tool.
http://docs.info.apple.com/article.html?artnum=303979 -
If you’re using the paired remote and the Apple TV status light flashes white, the problem isn’t with the remote.
Then what is the problem since I have troubleshoot my remote, it is working but cannot do anything on apple TV?If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Reconnect the power cable (only for Apple TV 3)
Open iTunes.
Select your Apple TV in the Devices list, and then click Restore.
(You may already have a micro USB cable if you have a camera or other digital device) -
I have an apple tv and the light blinks rapidly and continuously after a power outage. does this mean my apple tv has been permanently damaged?
Hello there, Philip.
For understanding the status light on the Apple TV, the following Knowledge Base article offers up some great information on what they mean:
Apple TV: About the status light - Apple Support
Apple TV (2nd and 3rd generation)
Status light
Apple TV (2nd and 3rd generation) is:
Flashes quickly
Having issues. Try restarting or waking your Apple TV. If your Apple TV does not start up properly, you might need to reset the Apple TV or restore it to factory settings. See Apple TV (2nd and 3rd generation): Restoring your Apple TV. If this does not resolve the issue, refer to the Service FAQ for additional assistance.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro. -
Status light flashes. Apple on TV.
Been using Apple TV more frequently lately. All of a sudden status light flashing continuously and an apple on the screen. I have unplugged everything for an hour and still no luck. held down menu button and other buttons...no luck. Please help so we can watch Apple TV again! Do I need to "reboot"? If so, how!
Hello Kardsy,
The links below detail how to restore both the 1st generation Apple TV and the 2nd and 3rd generation Apple TVs.
Apple TV (1st generation): How to perform a factory restore
http://support.apple.com/kb/HT3199
Apple TV (2nd and 3rd generation): Restoring your Apple TV
http://support.apple.com/kb/HT4367
Cheers,
Allen -
My airport time capsule did not set up successfully, and then status light flash amber
Hi, Guys
I am the first time user of the time capsule, please help how to proceed?
I have set up the first time and my airport time capsule does not set successfully, then I try to reset to factory setting. After this, although I use the ethenet cable to connect the router to the airport, the status light flash amber, always, even after the reset.
Also, I can see that airport time capsule base station from the wireless network when airport is plugged in. However, when I want to access to it.Thanks for your guidance, but the product is really anoying. First, I am sure that the airpor utilities is 6.3.
and I also follow your instruction that to set the IPv6 as local link mode. But still get the same error as mentioned in my first post.
Therefore, I have tried to use the bridge mode but could not find it, and therefore still can not set it up successfully, even though I reset the factory again(press the reset button 5 secconds at least). -
Cisco 1130 status light flashing orange
hello,
I have a question, I have an ap (cisco 1130) that began to get the status light flashing orange and light Ethernet and radio are off.
I did a factory reset and it was ok ... past 3 days the problem has happened again ...
I changed the ap with a new but the situation remained ...
I tested the wiring and everything is ok.
the switch port is set up correctly
may be what??
problem switch??or problem ap??hello,
I connect the console in to the WAP and then reboot the result of the bootup is as follows:
Xmodem file system is available.
flashfs[0]: 26 files, 8 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 6858240
flashfs[0]: Bytes available: 9140736
flashfs[0]: flashfs fsck took 31 seconds.
Base ethernet MAC Address: 00:24:97:6e:2c:e2
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
link auto-negotiating....
auto-negotiation takes 10000 milli-seconds to complete
ERROR: timeout waiting for auto-negotiation to complete
ERROR: fail to bring ethernet link up
The system has been encountered an error initializing
ethernet port. You may need to check hardware
The system is ignoring the error and continuing boot.
If you interrupt the system boot process, the following
commands will reinitialize ethernet, tftp, and finish
loading the operating system software:
ether_init
tftp_init
boot
Loading "flash:/c1130-k9w8-mx.124-23c.JZ/c1130-k9w8-mx.124-23c.JZ"...########################################################################################################################################################################################################################################################################################################################################################################################################################################################
File "flash:/c1130-k9w8-mx.124-23c.JZ/c1130-k9w8-mx.124-23c.JZ" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(23c)JZ, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 06-Apr-11 15:01 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 26 files, 8 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15740928
flashfs[1]: Bytes used: 6858240
flashfs[1]: Bytes available: 8882688
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Radio0 present A506 7100 E8000000 A0000000 80000000 3
Radio1 present A506 6700 E8000100 A0040000 80010000 2
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1131AG-E-K9 (PowerPCElvis) processor (revision B0) with 25590K/7168K bytes of memory.
Processor board ID FCZ1317Q102
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 7.0.98.218
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:24:97:6E:2C:E2
Part Number : 73-8962-14
PCA Assembly Number : 800-24818-13
PCA Revision Number : A0
PCB Serial Number : FOC13142PXW
Top Assembly Part Number : 800-29144-03
Top Assembly Serial Number : FCZ1317Q102
Top Revision Number : A0
Product/Model Number : AIR-LAP1131AG-E-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:05.864: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.480: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.066: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:09.154: %LWAPP-3-CLIENTEVENTLOG: Unable to open event log file flash:/event.log
*Mar 1 00:00:09.155: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 0 messages)
*Mar 1 00:00:09.184: status of voice_diag_test from WLC is false
*Mar 1 00:00:11.294: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:11.358: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(23c)JZ, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 06-Apr-11 15:01 by prod_rel_team
*Mar 1 00:00:11.358: %SNMP-5-COLDSTART: SNMP agent on host CC-P2-AP4 is undergoing a cold start
*Mar 1 00:00:11.437: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:11.615: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:11.615: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:11.615: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:11.877: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:11.877: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:12.297: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:00:12.615: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:12.615: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:30.265: status of voice_diag_test from WLC is false
*Mar 1 00:00:30.308: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:00:40.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:00:41.348: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
*Mar 1 00:00:50.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:00.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:10.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:14.626: %CDP_PD-4-POWER_OK: Full power - NON_CISCO-NO_CDP_RECEIVED inline power source
*Mar 1 00:01:14.665: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:14.703: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:15.627: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:15.665: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:01:20.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:30.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:30.348: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:01:40.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:50.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:00.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:10.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:20.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:20.356: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:02:30.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:40.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:50.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:00.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:10.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:10.359: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:03:20.362: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:30.362: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
I was checking another thing, usually the switches we use here in my work supports a maximum of 14W per port or 15.4w, this wap is consuming 15.2w
Is this the problem??
the strange to me is that,in this same sw I have several WAP and they all use 12.2w
The device type in sw for WAP usually appears as LAP1131AG-AIR-E-K9 ... but this WAP appears as Ieee PD ...
What problems do you think is it? -
AP Express status light flashing amber for no apparent reason, network works fine
AP Express status light flashing amber for no apparent reason, network works fine, any ideas?
It flashes amber when there is some kind of conflict. If the internet is working but the amber light bothers you, airport utility ahould tell you why your airport is reporting a problem.
If airport utility thinks your airport is normal and the amber light bothers you, do a hard reset on the device -
Seagate FreeAgent Go is making a clicking sound and the light is rapidly blinking. My Macbook is no longer recognizing it. Is there any way to pull all the songs I have saved on it? The SeaAgent is less than a month old!
Does anyone know how to fix this issue?
Or at least recover the lost data?
Thanks!How to fix: the drive is in warranty, so contact Seagate for a replacement.
How to recover your data: Do you have backups? (If not, you really, really, should.)
You can try downloading Data Rescue, which will run in trial mode and let you know if the data is recoverable. (You can then choose to purchase the full version if it works for you.) A clicking drive, though, is usually (though not always) a sign that the drive cannot be recovered.
Matt
Edit: fixed link. -
Dv4-1365dx Caps and scroll lights flash 4 times.
When I turn on my computer, the hard drive starts but then stops. The lights on the touchbar (next to the power button) come on, but the screen does not. Then, the caps lock and scroll lights flash 4 times in sequence. My warranty expired last year, what do I need to do to fix my problem?
This question was solved.
View Solution.If the hard reset suggested by Erico does not resolve the problem,
I think it is a hardware issue with graphics if the leds are blinking 4 times. Refer the following weblink:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01443366&cc=us&lc=en&dlc=en
I am an HP employee.
Regards,
Vidya
Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.
***Click on "Thumbs up" button to the bottom right side of my post to say thanks!*** -
Desktop Computer dc5750 shuts down and red light flashes on front of computer and won't start at all
I have a DC5750 HP Compaq Computer it is 6 years old, but I have 4GB Ram, Nvidia GS8400 Graphics Card, two one TB Hard Drives. While I tried to re-installed my operating systems it all of a sudden shut down not once but twice, I opened up the side of the computer and found that it was hotter then normal. I let it sit for a while thinking it maybe over heating after hooking it back up I turned it on again nothing happened except a beeping noise and red lights flashing on the front. Can this be fixed as money is an issue.
Thanks
RobHi, Rob:
Please review Appendix A. starting on page 56 of the Troubleshooting Guide at the link below to interpret the beep codes and see the probable causes and recommended troubleshooting steps.
http://h20566.www2.hp.com/portal/site/hpsc/template.BINARYPORTLET/public/kb/docDisplay/resource.proc... -
How do you switch output sounds set to my external monitor that is connected via HDMI.
How do you switch output sounds set to my external monitor that is connected via HDMI.
Hello gail from Ajijic,
If you'd like to change the audio output of your Mac, you can do so by accessing the Sound preferences in your System Preferences.
Before you start, open the Output pane of Sound preferences (choose Apple menu > System Preferences, click Sound, then click Output).
Choose a sound output device
From the list of sound output devices, select the one you want to use. All sound output devices available to your Mac are listed, including the computer’s internal speakers, devices plugged into your computer’s sound port (), USB speakers, and AirPlay devices.
For any device plugged into the computer’s sound port, choose Headphones.
OS X Yosemite: Adjust your computer’s sound output settings
Thanks for using the Apple Support Communities!
Cheers,
Alex H. -
My "Apple TV" is hooked up via HDMI to my Marantz receiver. Everything works fine when watching movies. When trying to watch a show or listen to music, there is no sound. Has this happened to anyone else?
Perhaps you should ask over in the iPad community, you may get better answers there.
It's actually my fault that psoon ended up here ... s/he intially posted over at Home Sharing, and I tried a relocate request to Apple TV rather than iPad.
psoon, here's a link to the iPad community:
Using iPad -
P2015 Ready Light flashes 4.5 minutes
I wrote a file printing program using CodeGear (previously Borland) Delphi that prints Delphi source code files on both sides of half sheets (5.5 x 8.5 ); I manually refeed the pages for printing on the reverse. The program bypasses the Windows printer canvas by using Windows API printer functions to send PCL 5 escape-sequences directly to a HP P2015dn printer connected to the USB port using the PCL 5e driver (The same results are obtained using the PCL 6 driver). The program changes the font to 16.67 char/in, changes the lines/in, changes the margins, and repositions the cursor several times.
The program performs exactly as planned but after the last page is printed, the printer reset command is sent, and the printer is closed, the printer's Ready Light will continuously flash for 4 minutes and 40 seconds then turn steady-on as is normal. But even while the Ready Light is flashing (implying that the printer is receiving data), the above program can be run again and it will immediately print whatever file is requested.
Does anyone have any idea why the Ready Light flashes for 4 minutes and 40 seconds after the print-job is complete?http://supportforums.blackberry.com/rim/board/message?board.id=8100&message.id=13769#M13769
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code
Maybe you are looking for
-
Hi I have a problem with my firefox browser. please Help me! In some computers I cannot find "Switch Page Direction" on the shortcut Menu or "View" Menu. Is there any setting related to this subject? thanks
-
Hi there Tried to use the error table property of target table. Ensured one record violated not null constraint. This record not sent to error table. Also tried adding not nul constraint as a data rule. Any ideas? Also what is best way to log errors
-
I just started a film business for shooting weddings and such. I also recently started a website. Tallproductions.com I want to be able to have an order form that people can click on and download that then just has some blanks so they can enter text
-
once the download is complete I do NOT get the firefox logo. The logo that appears on my desk top is an alias.
-
Hi, I'm running latest Arch with native systemd + slim +openbox. I think that a recent change has changed the way that slim + openbox is working. slim.service is working and I can log in openbox is started via .xinitrc using exec openbox-session in a