Apple TV's Promotheus loading issue

I purchased the Promotheus on Apple TV and watched it for about 15 minutes, Then it stopped and kept loading. The screen informed me the movies would be available in 2 hours 45 minutes. That was silly and wrong and it ruined my movies' night. I would hesitate to buy movies again from iTunes/Apple TV.

Your need to contact the itunes store support. I am sure they will help you out.
https://expresslane.apple.com/Issues.action

Similar Messages

  • When turning on my mac book pro it displays a screen with apple logo and begins loading a loading bar, after this continues to show loading circle however has been like this all day still no different. Tried turning it on and off however still same!

    When turning on my mac book pro it displays a screen with apple logo and begins loading a loading bar, after this continues to show loading circle however has been like this all day still no different. Tried turning it on and off however still same!

    ... then run Disk Utility, Repair Disk.
    Also:
    Resolve startup issues and perform disk maintenance with Disk ...
    Mac troubleshooting FAQ: start-up woes
    How To Fix Common Mac Startup Problems
    Mac Stalls on Gray Screen at Startup - Troubleshooting Mac Startup ...

  • Apple TV won't load or play movies from my MBP library (through both airplay and homesharing), but will from my mac mini. Help!

    I have been using my apple TV seamlessly with all my apple products (Mac Mini, iphone, MBP, ipad). Everything worked perfectly until recently (I noticed the issue about 3 weeks ago), when the apple TV won't load and play any movies from my iTunes library located on my MBP. The Library loads, and I can see everything, but as soon as I press play, the spinning load icon appears and doesn't stop. Same when I play movie from itunes directly and send it via airplay. Desktop mirroring no problem.
    I have checked, and films are being played perfectly from my other devices, as does airplay and mirroring

    Hello Tourneurm,
    Thank you for contacting Apple Support Communities.
    This article might be of use for your issue.
    Troubleshooting Home Sharing
    http://support.apple.com/kb/TS2972
    Section 8 seems to be most applicable.
    8. Cannot access my library when my computer is asleep
    For Apple TV to access your library while the host computer is asleep, "Wake for network access" must be turned on.
    Open System Preferences > Energy Saver and select (enable) the "Wake for network access" option.
    In addition, the network that the host computer and the Apple TV (2nd or 3rd generation) is connected to must support Wake on Demand feature. This works by partnering with a service running on your AirPort Base Station or Time Capsule called Bonjour Sleep Proxy.
    This article could also be of use.
    Apple TV (2nd and 3rd generation): Troubleshooting playback performance
    http://support.apple.com/kb/TS3623
    Regards,
    Jeff D.

  • My computer suddenly decides not to work and turns on but does not go past the grey apple screen with the loading wheel.. it will not go to my desktop. What should i do?

    can somebody please help me fix this issue, i have been sitting at my computer all last night and this morning trying to figure it out. It could be the hardrive or anything really i just need to get it working. Alot of important things that need to be done using this computer and i am freaking out.
    My computer suddenly decides not to work and turns on but does not go past the grey apple screen with the loading wheel.. it will not go to my desktop. What should i do?

    Put your install DVD into the optical drive (CD/DVD drive) and reboot. Be sure to either use the disc that came with your Mac, or, if you installed a later Mac OS X version from disc, use the newer disc. As soon as you hear the boot chime, hold down the "c" key on your keyboard (or the Option Key until the Install Disk shows up) until the apple shows up. That will force your MacBook to boot from the install DVD in the optical drive.
    Or if you are running 10.7 Lion, boot from the recovery partition (Command +R on boot) and use Disk Utility to repair your OS 10.7 partition.
    When it does start up, you'll see a panel asking you to choose your language. Choose your language and press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it. When it comes up is your Hard Drive in the list on the left?
    If it is, then click on the Mac OS partition of your hard drive in the left hand list. Then select the First Aid Tab and run Repair Disk. The Repair Disk button won't be available until you've clicked on the Mac OS partition on your hard drive. If that repairs any problems run it again until the green OK appears and then run Repair Permissions. After repairing use Startup Disk from the same menu to choose your hard drive for restarting from your hard drive.
    If your hard drive isn’t recognized in Disk Utility then your hard drive is probably dead.

  • Apple Remote Desktop-client mac issue

         Dear all,
                   I have using Apple Remote Desktop 3.7.2 on maverick,in that some of the client machine also visible offline, but i can take remote.
    i don't no why.plz help me
    Regards,
    Venki   

    Yes I've tried to ping the IP address and I get a reply.
    I've just discovered this morning that the issue appears to be with Apple remote desktop.
    The issue came up again this morning...I ended up shutdown ARD completely then loaded it back up, and guess what! The MAC address was showing up properly. I've discovered this is working for SOME of my issues. For the ones that weren't displaying properly I deleted the computer account out of ARD and then manually added the computer though a scanner import via single network address. The scanner finds the computer and it displays the correct Ethernet ID.
    So I’m guessing there is a bug with ARD and its mixing up/displaying the wrong Ethernet ID of some machines....
    Q

  • Apple Remote Desktop 3.4 issue

    Hi there,
    In Apple Remote Desktop 3.4 server I added a client computer by doing a scan by IP. Once the computer was added to a group I was able to take remote control, however after a few minutes I noticed the ARD console was having issues authenticating to it (Even though I authenticated properly to get the machine in ard). The ARD console was reporting that the computer was offline, but I was still able to observe and take control of the machine.
    I then noticed that the MAC address was the incorrect address. It was displaying another computer mac address that is on campus.
    My question: is ARD getting the Ethernet ID/MAC address from DHCP? WINS? DNS? Open Directory? LDAP? or from the client it's self? or do I have corruption in my ARD database?
    I am seeing this on a hand full of computers around campus (out of 500+ computers)
    (If I remove the client - the same thing occurs)

    Yes I've tried to ping the IP address and I get a reply.
    I've just discovered this morning that the issue appears to be with Apple remote desktop.
    The issue came up again this morning...I ended up shutdown ARD completely then loaded it back up, and guess what! The MAC address was showing up properly. I've discovered this is working for SOME of my issues. For the ones that weren't displaying properly I deleted the computer account out of ARD and then manually added the computer though a scanner import via single network address. The scanner finds the computer and it displays the correct Ethernet ID.
    So I’m guessing there is a bug with ARD and its mixing up/displaying the wrong Ethernet ID of some machines....
    Q

  • Apple logo and empty loading bar

    My iPhone4S won't turn on so i tried to factory reset it, and it is stuck on the apple logo with a loading bar that's empty and wont move. iTunes also says "Waiting for iPhone." Help please!

    Error 3194 usually means hacking software such as tinyumbrella altered the hosts file on your computer,
    Resolve communication issues
    Related errors: 17, 1004, 1013, 1638, 3014, 3194, 3000, 3002, 3004, 3013, 3014, 3015, 3194, or 3200. These alerts refer to gs.apple.com, say "There was a problem downloading the software," or say the "device isn't eligible for the requested build."
    Check the hosts file or TCP/IP filtering, which might cause communication issues between iTunes, ports, and servers.

  • TS2972 Apple TV 3 not loading iTunes library

    Is there any answer from Apple as to why my Apple TV is not loading my iTunes Library? It can recognise my library and all movies / music listed but will not load when selected, nor will it stream via airplay. I have viewed many many threads were people are experiencing the same issues but no answers from Apple.
    What is going on with Apple? please give us an answer

    The following article(s) may help you.
    Troubleshooting Wi-Fi networks and connections 
    Recommended Wi-Fi settings
    Sources of Interference
    Wifi Diagnostic Software (for Mac users)
    You may also find some help on this page, where I’ve collected some of the more unusual solutions to network issues.

  • Imac wont boot - i get a white screen with apple logo, and it loads to about 10%, then screen goes black

    imac wont boot - i get a white screen with apple logo, and it loads to about 10%, then screen goes black

    Hey there mtriest,
    It sounds like you are unable to boot the iMac successfully as it keeps shutting down when you try to boot. I suggest the troubleshooting from the following article named:
    Mac OS X: Gray screen appears during startup
    http://support.apple.com/kb/ts2570
    Disconnect, test peripheral devices and network cables
    Note: "Peripheral devices" refers to external devices other than what came with your Mac, such as hard drives, printers, or hubs that you connect via a USB or FireWire cable.
    Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
    Disconnect all peripheral devices such as external hard drives or printers (leave only the display, a keyboard, and mouse connected).
    Disconnect any Ethernet cables.
    Start up your Mac.
    If you can start up this way, one or more of your peripheral devices (or installed software related to the device) is probably causing the gray screen issue. Connect one device, then restart your Mac to test for the issue. Repeat the process until you locate the device at issue. Make sure the device is powered if it needs to be to operate correctly. Check with the manufacturer of the device for support or possible software driver or firmware updates that may be available for the device. Try a different cable with the device if possible (such as a different USB or FireWire cable).
    Note: If you have multiple peripheral devices and the issue only occurs when they are all connected, but not when each device is the only peripheral connected, see the Additional Information section below.
    If you are using a desktop Mac with a third-party keyboard and/or mouse device, and the issue still occurs, try starting up with an Apple keyboard and mouse connected instead. Try starting with no keyboard and mouse connected, then connect them after start up. Also, try a different USB port on your Mac.
    If the gray screen issue persists with no devices connected, go to the next section (with the peripherals still disconnected).
    Perform a Safe BootSimply performing a Safe Boot may resolve this issue.
    Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
    Start your Mac, then immediately hold the Shift key. This performs a Safe Boot. Advanced tip: If you want to see the status of a Safe Boot as it progresses, you can hold Shift-Command-V during start up (instead of just Shift).
    Note: A Safe Boot takes longer than a typical start up because it includes a disk check and other operations.
    If your Mac starts up as expected, immediately try restarting.
    If the Safe Boot does not work, or the restart after a successful Safe Boot does not work, go to the next section.
    There is additional information in the article with further troubleshooting if needed.
    Thank you for using Apple Support Communities.
    Cheers,
    Sterling

  • Tap to click not working properly in Mountain Lion. How do I get apple to fix this major issue with mountain lion?

    The tap to click does not work with mountain lion as it did before the mountain lion install. I purchased a brand new imac in August of 2011 and got a wireless keyboard and selected the wireless trackpad instead of a mouse.  The trackpad worked wonderful pre upgrade with tap to click. Now after the install of the newest beast, I have to actually press the trackpad rather than a slight tap. I have carpel tunnel and this is causing great stress upon my hand. How do I get apple to fix this major issue with mountain lion?

    Perhaps, I was not clear enough.
    I have an imac purchased in Aug. 2011 which came with Lion 10.6 (two uprades before mountain lion)
    Recently, I just purchased a macbook pro retina with Mountain Lion
    On my imac, my settings allowed me to "tap to click" everything EXCEPT the initial log in at the star up of my imac, again running Lion 10.6
    On my macbook pro retina which has Mountain Lion, I set up the "tap to click" option, but notice that a "hard" click was neccessary when trying to click things. I thought this was a macbook thing (my first one) so I went and upgraded my imac to Mountain LIon, BIG MISTAKE! Now both my imac AND my macbook only have limited "tap to click" options. Before mountain lion I could "tap" to highlight and select text, tap and drag, and many other thiings that Mountain Lion has disabled.
    I am truly surprised that no one has noticed this MAJOR issue.
    Is there a way to uninstall this update, similar to how on a PC you can go back to a restore point.
    On another note even the way PREVIEW has changed is less user friendly, there used to be icons on the bottom right corner of the screen, now I have to double tap and select the option I would like to switch between contacts and thumbnails. This is really annoying and is causing me time when reviewing files.
    Just in case anyone was wondering, I did go to system preferences -> trackpad -> select tap to click
    In fact almost all of the trackpad functions have been selected.

  • SAP Mobile Sales 2.0 delta load issue for Sales Orders

    Hello,
    we have used Mobile Sales 2.0 with a Windows app for a while now. Our current issue is that sales reps won't see any historical sales order data on their devices.
    Background
    Due customer requirements, we need to make small changes to customer master data attributes and reload all customers from ERP to CRM. Then we ran delta loads (MAS_PARTNER followed by all other objects) to DOE, in which virtually all 5000+ customer accounts were compared. The delta load ran for about 3 days (some performance bottleneck we haven't located yet).
    During the delta load, data on devices was inconsistent. Accounts were missing and all transaction data disappeared. After the delta loads, all accounts and contacts are OK, save for a few. Data from activities (appointments, tasks) have reappeared, as they should. Only sales orders won't reappear. The sales orders exist in the backend and belong to active accounts and sales reps.
    Settings and troubleshooting so far
    We don't have any limitations for sales orders in CRM Sales Mobile configuration.
    We've run delta loads for all objects in transaction SDOE_LOAD.
    MAS_CUSTOMIZATION etc seem fine.
    We've re-run initial load for sales orders from CRM.
    In the test system, we've even reinitialized the whole CDS database on DOE and on the devices, then re-ran the loads.
    Checked steps suggested in discussion
    SAP CRM 2.0 initial load issue
    Historical sales orders (those created before the master data reload) exist in the backend, but don't show up on the device.
    If I change one of those historical sales orders in the backend, it gets sent to the device.
    If I create a new sales order in the backend or on the device, it is saved and replicated just fine.
    To sum it up, it seems DOE is unable to identify the sales orders relevant for replication.

    First Doubt i got clarify by my self as we can go with Unwired Runtime option .
    But i still have doubt in :
    2. How can i Modifying the Main Menu for iOS.
    i am able to customize the same for windows using files SybaseCRM.Configuration.xml file.
    Same how can i do for iphone/ipad.

  • Report loading Issue

    Hello all,
    I am using Oracle 6i  for  report and oracle10g for the database.I have created a matrix report in oracle Report but which report taking so much time  to show the output it almost taking more than 10 minutes,at the same time that query executed within 1 minute in toad which used in matrix report.
    kindly guide me how to solve the loading issue.

    I did not used any formula column in my report,all the values are taking from query.
    But I used different types of format trigger in my report for the coloring purpose.Does it make any problem?

  • I updated to iTunes 10.5 on Vista. As with iTunes 10.0, The DEP will not allow iTunes to open.  WHEN IS APPLE GOING TO ADDRESS THIS ISSUE?  I can't update my telephone or iPod.  I can't even open the iTunes program!!!

    I am sick of dealing with this issue.  I wish not that I had never even started using any Apple products, beginning with iTunes.  WHEN IS APPLE GOING TO ADDRESS THIS ISSUE AND MAKE ITUNES SOMEHOW COMPATIBLE WITH DEP IN WINDOWS VISTA?
    That being said, Is there any way to resolve this?  What I did in the past is completely wipe ALL Apple files from my computer, and install an older version of iTunes.  It was at least functional.  It seems that any version of iTunes 10.0 or more recent is not compatible with the Data Execution Prevention in Windows.  You can not remove iTunes from DEP, yet DEP prevents iTunes from running.
    The down side is that I can't get the latest updates for my iPhone or iPod.  Now, I have a new phone for my husband that needs syncing on my iTunes, and I can't do that because iTunes won't even open.
    Can somebody help me out with this, please? 

    OK, lets do a complete overhaul to make sure it's working ok.
    First to check your Windows system file for any corruption:
    Go to command prompt (START/ALL PROGRAMS/ACCESSORIES right mouse click "command prompt" and choose "Run as Administrator"
    type in
    sfc /scannow
    let Windows fix any system files that need to be repaired.
    Restart the computer.
    Start iTunes and see if it is ok.
    If it doesn't, will have to go through the whole process of uninstalling and installing acccording to the following steps:
    1. Go to Microsoft website to fix install and Unistall problems. Click "Run now" from Fix it to remove all iTunes & related installer files:
    http://support.microsoft.com/mats/Program_Install_and_Uninstall
    Be aware that Windows Installer CleanUp Utility will not remove the actual program from your computer. However, it will remove the installation files so that you can start the installation, upgrade, or uninstall over.
    2. You should remove all instances of iTunes and the rest of the components listed below:
    it may be necessary to remove all traces of iTunes, QuickTime, and related software components from your computer before reinstalling iTunes.
    Use the Control Panel to uninstall iTunes and related software components in the following order:
    iTunes
    QuickTime
    Apple Software Update
    Apple Mobile Device Support
    Bonjour
    Apple Application Support (iTunes 9 or later)
    (Referenceinstructions from Apple article listed here: http://support.apple.com/kb/HT1923 to remove all components)
    3. Reboot your computer. Next, download iTunes from here:http://www.apple.com/itunes/download/ and install from scratch

  • Hi! My macbook pro wont switch on at all, pressing the power doesnt do anything, when plugged it switch on to get the white background with the apple sign and a loading button that kept on forever. anyone has a clue?

    Hello as mentionned before I cannot get my macbook pro to switch on.
    when it is not plugged as I press the power button nothing happens, when the computer is power plugged, it gives me the white blackground with the apple centered and the loading button below but it keeps loading forever left it as for 4 hours and still nothing.
    I have try to reset the SMC but didn't change much, now instead of the apple logo I get a circle crossed
    My macbook is 1 year and 4months

    See Gray Screen, try holding the Shift key upon boot
     Cheat sheet to help diagnose and fix your Mac
    Drive may not boot, but if it's still working then data can be recovered
     Data recovery efforts explained
     Most commonly used backup methods explained

  • I've tried to set up a new user on a mac book pro and i restarted it to create the new account but now all i can get is a white screen with the apple logo and the loading symbol what can i do ?

    i've tried to set up a new user on a mac book pro and i restarted it to create the new account but now all i can get is a white screen with the apple logo and the loading symbol what can i do ?

    Look at this support article:
    http://support.apple.com/kb/ts2570
    Ciao.

Maybe you are looking for