AppleTv (3rd gen) not connecting either way?

Apple Tv won't connect to the Internet - neither ethernet nor wifi... How's that? (Of course the router's working - that's how I'm writing this...)
NOTE: after being disconnected the whole night IT DID connect, update, etc, then it all went away for no apparent reason, and I'm stuck again with the box not speaking to the net... And it also says "Activation failed" in the "about" section....
I've run out of ideas...

Have you then tried going to Safari and look for a page that you have to acknowledge the terms and conditions to use the connection?
Next talk to the hotel staff. Some free networks use Flash or Java and can't be used by iDevices.

Similar Messages

IPod 3rd Gen Not Connecting to Windows AT ALL

i have an iPod 3rd Gen 10gb. I use firewire to connect it to my iPod. When i connect it, it shows that it is charging but that is all. my computer won't recognize it at all. i tried a new cable, a new firewire card, i bought a USB cable, reinstalling iPod software and iTunes, the 4 R's obviously not restoring cuz it wont connect. i basically tried everything but no luck. any help would be appreciated.

Do you use iTunes 7? If so please read the Topic I posted. Apperently I got the same problem with a new Nano. I discovered that when you attach the iPod DURING a Windows XP reboot it WILL WORK and see the iPod ...... until you disconnect again.
Please see the Topic I posted:
http://discussions.apple.com/thread.jspa?threadID=647294&tstart=0
Best regards
TheFactory

3rd Gen not connecting to WiFi

I cannot connect to wifi in hotel even though the ipod itself recognizes the WiFi connection. get error message that Wifi not connected, why?

Have you then tried going to Safari and look for a page that you have to acknowledge the terms and conditions to use the connection?
Next talk to the hotel staff. Some free networks use Flash or Java and can't be used by iDevices.

WRT54G ver.6 wireless router will not connect either way

WRT5G ver.6 Router will not connect to the internet or other PCs wired nor wirelessly, PC shows "limited or No Connection". The orange light is not on and will not come on when I press the Cisco System Light/Button on front. I cannot access the router through the browser nor PING it through the command prompt. I have tried to reset it and unplug it for few seconds, please, me OBIWAN, your my only hope.

I think your router is bricked, You can try the steps on this link and check if it solves your problem or not.

ATV 3rd Gen not connecting to itunes store

Hi,
I have an apple TV 3rd generation and I can only see 2 Tiles ( settings and homesharing)
No netflix, movies, or any other channels are available.
I've tried to sign in to the itunes store but a "cannot connect to iTunes Store" message appears.
Also tried WiFi, ethernet, reseting and restoring the ATV but nothing seems to work.
What can I do?

This could be a symptom of a wide-spread issue with ATV's right now [though looks to be primarily Gen 1 units]. There's an existing topic here: https://discussions.apple.com/message/25524317#25524317 Your case could be a sign that the problem has spread beyond jsut the Gen 1 units. It could also jsut be a sign that Apple is trying to address the issue with Gen 1, and it is temporarily affecting other generations.
Be sure to click "I have this question too" in the thread above, and identify the generation of your device in a reply (As it may affect other generations as well.), so that it's all collected in one place. I also suggest to submit the bug via the feedback page https://www.apple.com/feedback/appletv.html

Ethernet connectivity problem appleTV 3rd gen to airport extreme 5th gen

I have an airport extreme connected with Tivo via a Trendnet ethernet plugin adapter via electrical outlet, and it works fine. When trying to connect my AppleTV 3rd gen to another ethernet port of airport extreme with another faster (85mbps) Trendnet ethernet adapter via a different electrical outlet, my extreme goes from green light to flashing amber light and my wifi stops working. Only when I disconnect the ethernet and start using wifi for my appleTV, will the airport extreme start working again. It's driving me nuts.
My setup is ethernet (no cable modem or DSL modem) with the ethernet cable that supplies internet to my house coming through a router device (I think it is?) that is plugged into my airport extreme. However, I do have a double NAT setup as my ethernet service has its own NAT too. I tried switching from DHCP and NAT on the airport extreme to bridging mode as recommended, but then my internet doesn't work and I get a flashing amber light. So I went back to DHCP and NAT on my extreme and am ignoring the double NAT, and so the wifi works fine now.
I have done multiple hard resets of all devices involved including the appleTV, airport extreme (I have set up my network at least 10 times) and have unplugged my router device and disconnected the ethernet cable supplying internet to the house as well. Nothing seems to work. I called tech support, and originally thought that my 3rd ethernet port wasn't working, so they mailed me another unit, which doesn't work as well (in fact, I keep getting a message to unplug my cable or DSL modem or disconnect the battery pack to cycle it no matter what I do but that is for another time).
Would greatly appreciate any help. Thanks.

When trying to connect my AppleTV 3rd gen to another ethernet port of airport extreme with another faster (85mbps) Trendnet ethernet adapter via a different electrical outlet, my extreme goes from green light to flashing amber light and my wifi stops working.
If the Apple TV was originally setup for WiFi, I suggest that you reset the device back to default settings and then configure it again with Ethernet plugged in. Settings > General > Reset > Reset Settings
As a test, connect a spare Ethernet cable of any length (that you know is working) from the LAN <-> port on the AirPort Extreme to the Apple TV for the setup.
Setup the ATV again and double check to make sure that it is operating correctly
Change the location of the ATV back to the desired location on the network behind the powerline adapters
If you have a problem now, the first thing to check is the powerline adapter and or wiring

Anyone else having trouble using Home Sharing on AppleTV (3rd Gen) on wired network?

First my setup: I'm on a Mid-2010 MacBook Pro, D-Link DIR-615 Router, AppleTV (3rd Gen).
Problem: Couldn't connect to Home Sharing via the AppleTV.
I was having serious trouble getting Home Sharing working on my AppleTV (3rd Gen). I spent an hour on the phone with Apple Tech Support. Then, after forwarding the proper ports (http://support.apple.com/kb/HT2463?viewlocale=en_US), spending another hour and a half with D-Link. Then I even called my ISP. Anyway, after A LOT of futzing around, I finally realized that Home Sharing is working on my iPhone (4S), so maybe it's a wifi thing. I unplugged the ethernet cable from my AppleTV and connected it to my wireless network. Keep in mind, same network, just now it's connected via a different channel (wireless now versus wired before).
Suddenly, works just fine, no issues at all.
What's going on? Anyone have any idea? My port forwarding is now not even set to the correct IP address of my AppleTV (was ...100 when it was wired, but on wifi it grabbed ...103). It would be great to know what's going on. Also, hopefully this helps someone else having the same problem.

Yesterday I bought Apple tv, and connected it on a free LAN port on my DLINK DIR-615.
All settings are ok , appleID en home sharing are set en activated but nothing shows...
The problem seems simular on yours. Tonight when I get home, i'll disconnect de LAN and try wireless....
We will see. Thanks fot the hint

HT201343 I can not see AIRPLAY Icon on My IMAC to mirror my new APPLETV 3rd gen my imac was bought from apple store in september 2011

my IMAC is OS X LION 10.75
mid 2011

About AirPlay and Airplay Mirroring
AirPlay Mirroring requires a second-generation Apple TV or later, and is supported on the following Mac models: iMac (Mid 2011 or newer), Mac mini (Mid 2011 or newer), MacBook Air (Mid 2011 or newer), and MacBook Pro (Early 2011 or newer). For non-qualifying Macs you can try using Air Parrot.
Several Apple Articles Regarding AirPlay
Apple TV (2nd and 3rd gen)- How to use AirPlay Mirroring
How to set up and configure AirPort Express for AirPlay and iTunes
iTunes- Troubleshooting AirPlay and AirPlay Mirroring
iTunes- Using AirPlay
Apple TV (2nd and 3rd gen)- Understanding AirPlay settings
About AirPlay Mirroring in OS X Mountain Lion
iTunes 10- About playing music with AirPlay
Troubleshooting AirPlay and AirPlay Mirroring
Using AirPlay
Thanks to the $15 Beamer, AirPlay streaming is still possible on Macs that do not support Airplay and mirroring.
Other solutions are the Air Parrot, StreamToMe, and AirServer.

Ipod Touch 3rd gen not chargin anywhere else that it isn't my macbook pro and only works on one of the USB ports the other one doesnt recognize it... I use the same USB cord to charge it on the wall for some time now it wont even charge on the wall

i have an ipod touch 3rd gen this is my second ipod touch my fist one the battery died after 4 years so then a bought this one (ipod touch 3gen) and it works perfectlybut for some time know it wont charge anywhere else thats not my macbook pro and the thing is the only charges and its recognized only on one of the USB porst of the laptop i have a windows 7 computer but it wont charge there have a linux (ubuntu) machine and doesnt work either, the wall charger with the same cable i use on the laptop and wont charge either i plug it on my sisters car and wont charge my char wont charge anyways i wont charge anywhere else thats not my macbook pro only with 1 of the 2 USB pork that the MBP has..... any help? can someone ewlp me? i really doubt its the battery cause it charges fine on my MBP :/.... oh now i recently upgrade to OSX Lioin but the problem perssist I did the recent update but the problem persists :/

- See:
iPod touch: Hardware troubleshooting
- Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
- Try another charging source
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

Ipod touch 3rd Gen not fully starting up - constantly restarting with the apple logo screen

Hi,
First of all, I cannot get my ipod touch (3rd Gen) to start up so I cannot get model specifics and version numbers - though it is iOS 5.1.1
I have obviously tried to restart it by holding the power and home button for 10 secs but this has not done anything.
At the moment, the ipod switches on and I see the black screen with the white apple logo - this stays on for about 3 minutes, then I get the little spinning circle (but it isn't spinning) for a couple of minutes, before it powers off and does this again... repeatedly. It only stopped because the battery power ran out.
I have connected it to my computer with the latest version of itunes - it appears in the devices list but just has a spinning 'loading' icon and is grayed out. As my ipod restarts the cycle again as above, my computer makes the noise as if i just plugged it back in and the above happens again in itunes.
The problem began when I updated apps (through update apps in app store) and it froze - I turned the ipod off to restart it, and now this is happening.
Any help or advice extremely grateful... I can't even access it to get it restored which is a bit of a problem as I have work notes on it. (Obviously I don't know if notes are backed up on ipod backups through itunes?)
Many, many thanks in advance!

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

3rd Gen Nano connects and then QUICKLEY disconnects on an XP machine

Below are two postings I made in a different discussion area. The 30g iPod is now working fine, the Nano is as stated in the second post. Please to help me out? As stated below Apple says it works and it does on the wrong machine! As many of you out there know, sometimes a husbands and a wifes taste in music are different. I would like to keep my music on my machine. Thanks, reo52............
I have been running very well with my 30g Video iPod. I got an 8g nano as an award. I had just upgraded iTunes, tried hooking the nano up and now nothing works! iTunes never did find the nano. Did the r,r,r,r,r thing but could only reset because iTunes can not see the nano. Later I was syncing the 30g and was ejecting it and got a message stating it could not be ejected as there are files on it being used by another program. Did the 5R's on he 30g, the unit was syncing and the battery went low and interrupted the sync. Now iTunes can't see the 30g or the 8g. I did a reinstall of iTunes and still nothing. This is driving me to drink, HELP if you can. Thanks, reo52.............
Well, I sent the Nano in, it came back, Apple found no problems with it. When trying to sync it acted as before. With Apple on the phone I tried syncing to my wifes machine!?? I'll be dammed it synced right up!???! Well Apples says it works because it works on my wifes machine!! Well, why wont it work on my PC?!!. Both machines are running up to date iTunes, both have the same firewalls and virus programs and both are running XP with all service packs and updates installed. Now I can work around this for awhile but I have got to get that Nano to sync with my machine. Help if you can and Thanks again, reo52

To Apple,
822 unresolved problems in "Connecting 3rd Gen Nano to a Windows Machine" , 25-50% on each page are problems with connecting a Nano in Windows and getting it recognized in Windows or iTunes or syncing errors(1st 5 pages). I think this qualifies as a serious problem. Many state that their Nano works on a different Windows machines and or an Apple machine, but not the one they use. Others and myself have sent their Nanos beck and Apple. Apple states "unit works fine, can not reproduce problem, or words to that effect" then Apple sends it back! It still will not work for the customer. So who has the problem? Owners who can not use their Nano? Apple who has the owners cash but maybe not their goodwill? I do not know, but I can see a Customer satisfaction problem developing. So APPLE please do your best to resolve this situation. It could be to your own advantage and help with those 822 unresolved problems on the Nano Pages. Thanks, reo52

AppleTV 2nd gen not updating YouTube app-

Ok. Learned of the newest updates for apps on my AppleTV 2nd gen. Read about how the YouTube app was new and was hoping to play around with it. But when I got on, I found that it has not updated.
I updated the software thru the Setting app. No joy. Restored the AppleTV to factory spec with supposed latest update. Still no joy.
Anyone else have this issue? Searching has not revealed anything yet.
My info:
Model: MC572LL/A
Software: 6.2.1 (6698.99.50.41)
connected by ethernet to Apple Extreme Base Station
Thanks in advance.

I have the exact same problem. The other new channels from the Monday(?) update showed up, but my YouTube app has not changed. I have an AppleTV 2 (i.e. the first hockey puck), is the update limited to certain models?

Old iPod 3rd gen not showing up in iTunes

Hi, I realize this may be a futile effort but I thought I would give it a try.
I have an old ipod, 3rd gen 15GB that still works fine, stores a lot of music and plays fine. I would like to update and restore it. I have the old computer I used it with, an iBook G4 OSX 10.4.11 running iTunes 8.2.1, the most updated it can get for this computer I think.
Im just wondering how I can restore the ipod and put mp3s on it. It doesnt show up in itunes but appears to be charging when I plug it in with the old firewire cable. its working ok to the best of my knowledge and I would like to do a hard reset or something but I cant figure out how. Any help would be appreciated. Thanks!

Hey there Miles,
It sounds like your iPod isn't showing in iTunes when you connect it to your Mac. I would start with this bit from the following article:
iPod not appearing in iTunes
http://support.apple.com/kb/TS3716
First, try the steps in the iPod Troubleshooting Assistant which applies to your iPod.
If you still cannot get the device to appear in iTunes, use the following link to help troubleshoot it:
iOS: Device not recognized in iTunes for OS X
http://support.apple.com/kb/TS1591?viewlocale=en_US
Thank you for using Apple Support Communities.
Take care,
Sterling

IPod 3rd gen not working with universal dock

My old iPod 3rd gen (15GB, touch wheel, dock connector) worked great with the old dock, until the latter started scratching noises when outputting audio to my stereo. Still charges the iPod though.
So, I tried old iPod with the universal dock I got for my Touch and found the following problems:
1. iPod is not being charged through new dock plugged to wall adapter
2. touch wheel menu control is not working as long as iPod sits in universal dock plugged to the wall adapter - the sound of clicks is all I get, but no control of menu or any other function. In order to select playlist or use any other function through touch wheel or any of 4 buttons I need to unplug power from the dock (it is not charging anyway)
3. remote is not working at all
Otherwise playback is OK.
Any ideas what may be the culprit here? Apple states that Universal dock is compatible with 3rd generation of iPod and up.

Hello Andrew,
What a coincidence as I too have had to find a new dock for my 3rd gen ipod. This week I purchased an Apple AV Connection kit - but found that it would not charge the ipod or respond to the remote. I also bought and tried a Belkin AC adapter with cable to power up the ipod but it too would not charge the ipod.
To see if these units were working I connected them to a friend's brand new ipod classic and both the Belkin and Apple AV Connection Kit worked fine - so there is something different about the 3rd gen ipod.
I'm not sure if this helps you - but at least you know it's not just your ipod that is not working with the new dock.
Nick M.

Ipod nano 3rd Gen not recognized by itunes or windows 7

USB device not recognized.
things I have done
put Ipod in disk mode still didn't recognized
My Ipod Classic 6th Gen works fine
It shows 3 Mass Storage Device
when I plug in Ipod nano 3rd gen it shows unknow device
have deleted Mass storage devices and Apple Moble Devices
unpluged computer from wall
nothing solving problem
I also tried it on my laptop its not being recognized
my wife Ipod nano is doing the same thing as mine
its got to be the software download from itunes because it has worked on all previous versions.

I have the same problem. My Iphone 4s works fine when docked to PC. PC won't recognize my 3rd Gen Nano. Same goes for my Work PC. They don't recognize it nor will plugging it in to a PC charge it. I have to plug it into wall socket to charge.
I have tried resetting, I have tried downloading newest Itunes.
Must be the Nano itself if it doesn't get recognized by mutliple PCs?
I haven't used the Nano for probably 2 months. Previously it worked fine...
One thing, when docked to my laptop during a reboot/startup, it intially starts to charge the Nano, but once setup is finished it doesn't recognize it any longer...

AppleTv (3rd gen) not connecting either way?

Similar Messages

Maybe you are looking for