AppleTV3 will not act as Bonjour sleep proxy

Hi everyone - I'm one of these people who has a 'little bit of everything' in my local network, so its only as I'm tearing it down to move house that I'm starting to find a few things. This one in particular relates to the Bonjour Sleep Proxy on the network - specifically that my AppleTV3s (I have 2 of them), neither will advertise a sleep proxy service (checked using 'dns-sd -B _sleep-proxy._udp local'), resulting in me being unable to wake sleeping machines (which do have 'wake for network' access enabled).
Now I have an old TimeCapsule, and also an old AppleTV2 - which, when I plug them in both will advertise as sleep proxies on the local network - but based on my understanding from this article;
About Wake on Demand and Bonjour Sleep Proxy - Apple Support
Anything later than an ATV2 should also work (i.e. either of the ATV3's). I've tried resetting to defaults, they are both running the latest firmware, and I have confirmed that it doesn't offer the service either over wifi or ethernet. I'm getting rid of unnecessary hardware as I move, the ATV2 and TC being both surplus.
Anyone else come across this and have a solution for ATV3's as a sleep proxy? (other than leaving the ATV2 and old TimeCapsule installed, purely for this purpose)

Hello blindjudge,
I was looking through our resources for information that may help you to troubleshoot the AppleTV not showing in the iTunes sidebar. Check out this article named: Troubleshooting Apple TV not recognized in iTunes found here http://support.apple.com/kb/ts1453.
This section in particular:
1. Restart iTunes (quit or exit and then reopen iTunes).
2. Reconnect Apple TV to iTunes.
Choose iTunes > Preferences (Mac) or Edit > Preferences (Windows), click Apple TV, and make sure "Look for Apple TVs" is selected.
If Firewall is on in Mac OS X (in the Sharing pane of System Preferences), make sure iTunes Music Sharing is selected.
Open iTunes on your computer.
Select the Apple TV icon with "Click to set up" next to it in the Devices list.
Enter the five-digit passcode from your TV screen.
3. Reset.If you are still having trouble, you can try to reset your equipment by unplugging power cords for the following:
Apple TV
Your TV
Your wireless networking equipment or AirPort Base Station
Your router from the power outlet.
Wait thirty seconds and then plug everything back in again.4. Restart your computer.5. Rejoin the network (wireless) or restart your network router.If you have an AirPort Base Station, see the troubleshooting section of the setup guide for your model. If you have a third-party router, check the documentation that came with it.
AirPort Express Setup Guide v4.2
AirPort Extreme Base Station Setup Guide
Designing AirPort Extreme 802.11n Networks
AirPort Extreme (802.11n) Setup Guide
All the best,
Sterling

Similar Messages

Bonjour sleep proxy?

Hi. Recently while on the internet, I got the message "another computer is using this IP address". I went to the console and checked the logs and saw multiple logs that read DHCP en1: defending IP against bonjour sleep proxy. Any suggestions as to what this is?

There are several possible causes for this behavior.
1. Two (or more) computers on the local network have the same Bonjour name, such as "X's-MacBook-Pro.local". Resolve the name conflict by renaming one or more of them in the Sharing preference pane.
2. You have two simultaneous connections to the same local network: probably Ethernet and Wi-Fi. If applicable, disconnect the Ethernet cable or turn off Wi-Fi.
3. A Mac wakes from sleep due to network traffic. This is a bug in OS X that may only affect some models. You can avoid it as follows:
Open the Energy Saver pane in System Preferences and unlock the settings, if necessary. Select the Power Adapter tab, if there is one. Uncheck the box marked
          Wake for Wi-Fi network access
if it's checked.
4. A device that gets its network address from the router wakes from sleep, and the address it was using before has been assigned to another device.
5. A third-party wireless router has incompatible settings or firmware. In that case, refer to the manufacturer or ISP for support. Restarting the router may help, temporarily.
6. If the router is an Apple device, it may need to be restarted.
7. A third-party Bonjour device on the network is malfunctioning. Finding out which is a process of elimination.
8. There is more than one DHCP server on the network. Typically, there would be two or more wireless access points configured to act as routers.
9. See this support article.
10. Back up all data. Make notes of your settings in the Network preference pane.
Triple-click the line below on this page to select it:
/Library/Preferences/SystemConfiguration
Right-click or control-click the highlighted line and select
          Services ▹ Reveal
from the contextual menu.* A folder should open with an item named "SystemConfiguration" selected. Move the selected item to the Trash. You may be prompted for your administrator password.
Restart the computer and empty the Trash. You will need to recreate the network settings.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
          Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.

HP LaserJet P3005x will not come out of sleep mode

Printer will not come out of sleep mode (after being in sleep mode for an extended period of time (over 24 hrs)). When this happens, I can not ping the printer and pressing any of the buttons on the printer will not bring it out of sleep mode. I'm testing now to see if I can recreate this with the printer attached to my PC via USB.

Hi arosecarter,
I understand your monitor is not coming out of sleep mode. Take a look at the following support document, Resolving Problems with Sleep and Hibernate Modes (Windows 7). Step 3 might be of particular interest to you, as you mentioned your keyboard and mouse are not really working for you either. Perhaps it is another connected device that is causing the issue? Anyway, hopefully this document will be of help to you. Best of luck. Have a wonderful day.
Ryan1216
I work on behalf of HP
The advice and opinions given here are my own and not those of HP

890FXA-GD70 Will Not Wake From S3 Sleep

890FXA-GD70 will not wake from S3 sleep; the power comes back on and the fans run but the video never returns and the system hard locks with a POST code of 22 or 24. Other than this issue the system is rock solid.
Windows 7 Ultimate 64
AMD Phenom II X4 955 Processor
Sapphire 5870 Graphics
Crucial M4 SSD
Corsair DDR3
No overclock
I have reproduced the issue on two 890FXA-GD70s motherboards and I am convinced that this is not a result of a failed motherboard. I also was able to move my fully installed SSD hard drive, processor, memory and graphics card to an Asus 890FX board and successfully wake from S3 sleep proving that my OS and driver installation are working correctly.
I know how to properly set the BIOS as I have installed many 890GXM-G65 motherboards for S3 sleep without issue. The problem seems unique to the 890FXA-GD70.
Is there a fix for this?

I have identified the cause. The "Extra RAID/IDE Controller" must be "Enabled" to use S3; otherwise the system will hang on the wake event. This is true even if the "Extra RAID/IDE Controller" goes unused. The "Extra RAID/IDE Controller" must be set to "Enabled" for S3 sleep to wake.
This would seem to me to be a bug since none of the other MSI boards I have used require the optional IDE controller to be enabled in order for S3 to function properly.

My MacPro will not wake up from sleep after the 10.8.2 upgrade.

Since latest os upgrade to 10.8.2, my mac will not wake up from sleep.

Please read this whole message before doing anything. This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it. The purpose of this test is to determine whether your problem is caused by third-party system modifications that load automatically at startup or login. Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode* and log in to the account with the problem. The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
*Note: If FileVault is enabled under OS X 10.7 or later, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs. The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

My iMac will not wake up from sleep after upgrading to OS X Mavericks

After upgrading to OS X, my iMac will not wake up from sleep. Each time I have to do a hard restart. Is there a fix for this problem?

Hi,
I have just had the same problem with my iMac and after upgrading to Mavericks my iMac would not wake without pressing the power off button and re-booting.
Anyway, I have since done a complete new install on my iMac and have gone 5 days without an issue with the iMac not waking. It was a bit of a pain to do but my own view so far is that the problem is linked to the upgrading of the OS instead of a clean install.
My iMac now flies with a new OS installed instead of an upgrade.

Mac will not wake up from sleep

I'm running 10,7,5 on 2x2.66 GHz Dual-Core Intel Xeon. The computer needs to restart because it will not wake after it sleeps. I've tried lots of different settings in the screen saver.
Any suggestions?

.... and you fail to mention the model SSD and firmware version... or how you installed or cloned the system
most people also move most of their user folder to another hard drive.
sounds like a more normal Mail + OS issue if just that.
hard restarts = directory corruption so don't reboot w/o first either Recovery Mode, then follow up with Safe Boot.
And maybe you have 3rd party hardware or software that is not compatible with 10.8.2 needs to be considered as well.
2008 model 3,1 also are having a lot of issues this year. Including another critical piece, what gpu it has.

Maverick will not wake up from sleep

Maverick will not wake up from sleep. i dont see any related issues. maybe i am the only one? Ive been trying to run maverick for the last 2 months. I thought everything was fine after I erased, reformated and partitioned the HD and installed Maverick on a clean drive...... and then i get the ? startup disk. And then when it does run, I cant let it go to sleep. It will not wake up from sleep. I get the spinning beach ball of death everytime. I leave my computer on and run to the grocery store and come back........ I have to shut my computer off from the control strip and push the start button, every time.
Anyone know if this will damage my computer??
I have selected the HD in the preferences startup; I've unplugged it for several minutes; started up in S mode; zapped the P ram; ran permissions; you name it. im at a loss.
Any help would be greatly appreciated. Should i buy another Mac? I cant afford one in this economy.

I suggest you use the Recovery Partition Disk Utility to check the hard disk and then re-install the OS from there.
http://support.apple.com/kb/HT4718?viewlocale=en_US&locale=en_US

HT1338 Mac mini display connection will not come back after sleep, I have to shut down and restart the monitor.

Mac mini display connection will not come back after sleep, I have to shut down and restart the monitor.

Finder icon on dock, macintosh hd, library, launch agent - delete all files & restart sleep to test
also
Finder icon on dock, macintosh hd,
Library/Preferences/SystemConfiguration/com.apple.PowerManagement.plist
delete file & restart sleep to test.

Energy saver will not put Mac to sleep

I have a new Intel Mac mini. I am running off an external drive (MiniStack2). The drive was formatted and then had data transferred from old G4. The internal drive, when used as a start-up disk, functions fine. The external drive will not enter sleep mode (screen turns off, but not HD). The G4 had similar problem. Not sure why one drive as start-up drive and other does not. I have quit all active processes and tried every set of options - the machine will not put HD to sleep.
Is there a plist or other file I must reload? I am certain this is a software issue. Problem in 10.4.7 and 10.4.8 (and 10.4.x on G4)

Welcome to the forums. You are a new user and are not familiar with the Discussions' Terms of User.
You should not post your specific problem in another poster's thread. This is called "threadjacking" and is frowned upon as well as considered inappropriate by the Terms of Use. Instead you should post your own separate question topic. This is easy to do. Simply determine which forum is most appropriate for your problem, navigate to that forum and the forum's topic list. Just above the topic list you will see on the left the words "Post New Topic." Click on that link and then prepare your post in the editor. When you are finished click on the Preview button to see how your post will appear. If it's OK, then click on the Post button to post your topic.
When you get a chance click on the "Help & Terms of Use" link in the right sidebar of any forum page and review the Terms of Use.

Bonjour Sleep Proxy protocol documentation?

Can anyone point me to a technical description of the Bonjour Sleep Proxy protocol description, or a technical description of how it works?
(I've already seen the Apple KB article http://support.apple.com/kb/HT3774
providing an overview of the "Wake on Demand" feature, the reference
to "Sleep Proxy Servers" in http://files.multicastdns.org/draft-cheshire-dnsext-multicastdns.txt , and the Sleep Proxy Service patent in http://patft1.uspto.gov/netacgi/nph-Parser?Sect1=PTO1&Sect2=HITOFF&d=PALL&p=1&u= %2Fnetahtml%2FPTO%2Fsrchnum.htm&r=1&f=G&l=50&s1=7,330,986.PN.&OS=PN/7,330,986&RS =PN/7,330,986 .)
What I'm really trying to understand is if the Sleep Proxy server is intended to take over the IP address belonging to the sleeping device. Based on the documents above, I gather that the Sleep Proxy server may respond to mDNS queries for services registered by the sleeping device. But I'd guess the mDNS responses come from an IP source address of the Sleep Proxy Server. I wouldn't expect the Sleep Proxy server to start sending IP datagrams using the IP source address of the sleeping client, or to respond to ARP Requests targetting the sleeping client's IP address. But lacking a technical description of the Sleep Proxy Server is expected to behave, I'm just guessing.
I ask because starting on September 3 2009, I've seen three Apple Time Capsules "steal" IP addresses belonging to other devices. (For several hours, the Time Capsule's uplink sent ARP Reply packets for an IP address that didn't belong to it. It did so at the same time it send ARP Reply packets for the Time Capsule's assigned IP address.) The victim of each IP address theft was a Macintosh computer that had no apparent relationship with the Time Capsule. The release of the Sleep Proxy client software in Mac OX X 10.6 several days earlier makes me wonder if Sleep Proxy service is the cause of these IP address thefts.

I moved this to the more appropriate "Mac OS X Technologies > Networking and the Web" forum, since it's become apparent that it involves more than Time Capsules.

Bonjour sleep proxy not working; Mountain Lion (10.8.1, 10.8.2) not waking up for remote management, itunes library

Since updating to 10.8.1 (I'm currently on 10.8.2), my Mac Mini no longer wakes for network access.
That is, when I attempt to connect remotely to the computer (i.e., mac mini is at home, I am at work), the computer never wakes up.
I have an Airport Extreme 2011, I believe; I updated it to the latest firmware a week or two ago. (Now that I think about it, maybe it was after this firmware update that the Bonjour sleep prox stopped working?)
Ideas?
My system:
Mac Mini (2011) with 8gb RAM
[added 2nd hard drive -- SSD]
Mountain Lion 10.8.2
Connected via ethernet cable to an Airport Exreme (2011)

Since upgrading to 10.8.2 I have had this issue.
I have 'Wake for Network Access' enabled but I am unable to wake my Mac Pro from my AppleTV2 using Home Sharing.
If I reset the PRAM, WOL works the first time the Mac goes to sleep but after that it wont work.
The Mac Pro still periodically wakes up (as in the fans and HDDs spin up, no GUI) to keep the network address alive but nothing can actually wake it, (except once on the first sleep after PRAM reset).
This was not an issue prior to 10.8.2.
I have also noticed since upgrading to 10.8.2 that after waking the Mac, it takes approximately 10-15 seconds for the network to re-connect. This is via a wired ethernet connection.
This also was not an issue prior to 10.8.2.
I really hope this is fixed with 10.8.3.

MBP Will not wake properly from sleep-flash of screen and keyboard for a bit every few seconds. Under guest account, wakes up just fine. I also cannot unlock various padlocks to change settings in e.g. system prefs. security? Any help, I'm dyin!

Not waking up from sleep-flashes lighted keyboard and screen, and I cannot unlock the padlocks in the system to change settings, look at keychain, etc.

Still cannot unlock system prefs/users etc.   Also, many applications are returning errors like: "failed to obtain the necessary authorization" or " '' failed to obtain permission" so I've attached a portion of my log, showing when I attempt to unlock (or click on the padlock) in system preferences - User Accounts:
3/7/13 7:52:51.180 PM
SecurityAgent[3818]
Problem during create from (builtin:login)
3/7/13 7:52:51.181 PM
SecurityAgent[3818]
Problem during create from (builtin:login)
3/7/13 7:52:53.982 PM
SecurityAgent[3818]
Problem during create from (builtin:login)
3/7/13 7:52:53.982 PM
SecurityAgent[3818]
Problem during create from (builtin:login)
3/7/13 7:52:58.794 PM
WindowServer[3177]
CGXSetTrackingAreaEnabled : Invalid tracking area 0x1642350
3/7/13 7:52:58.796 PM
WindowServer[3177]
CGXSetTrackingAreaEnabled : Invalid tracking area 0x1642350
3/7/13 7:52:58.827 PM
WindowServer[3177]
CGXSetTrackingAreaEnabled : Invalid tracking area 0x1642350
3/7/13 7:53:01.340 PM
helpd[3305]
Could not find access page in directory /Applications/Nomina.app/Contents/Resources/NominaHelp
3/7/13 7:53:01.342 PM
helpd[3305]
Could not find access page in directory /Applications/Nomina.app/Contents/Resources/NominaHelp
3/7/13 7:53:11.354 PM
helpd[3305]
CFPropertyListCreateFromXMLData(): Old-style plist parser: missing semicolon in dictionary on line 1. Parsing will be abandoned. Break on _CFPropertyListMissingSemicolon to debug.
3/7/13 7:53:11.355 PM
helpd[3305]
CFPropertyListCreateFromXMLData(): Old-style plist parser: missing semicolon in dictionary on line 1. Parsing will be abandoned. Break on _CFPropertyListMissingSemicolon to debug.
3/7/13 7:53:37.799 PM
WindowServer[3177]
CGXSetTrackingAreaEnabled : Invalid tracking area 0x1318260
3/7/13 7:53:37.800 PM
WindowServer[3177]
CGXSetTrackingAreaEnabled : Invalid tracking area 0x1642350
3/7/13 7:53:37.802 PM
WindowServer[3177]
CGXSetTrackingAreaEnabled : Invalid tracking area 0x1642350
3/7/13 7:53:37.819 PM
WindowServer[3177]
CGXSetTrackingAreaEnabled : Invalid tracking area 0x1642350
3/7/13 7:57:24.304 PM
PopClip[5202]
[INFO] PopAppDelegate: PopClip Initializing.
3/7/13 7:57:24.439 PM
PopClip[5202]
NSWindow does not support nonactivating panel styleMask 0x80
3/7/13 7:57:24.441 PM
PopClip[5202]
[INFO] PopAppDelegate: PopClip will wait 0.500000 seconds to start.
3/7/13 7:57:31.632 PM
SecurityAgent[5231]
Problem during create from (builtin:login)
3/7/13 7:57:31.633 PM
SecurityAgent[5231]
Problem during create from (builtin:login)
3/7/13 7:57:32.665 PM
SecurityAgent[5231]
Problem during create from (builtin:login)
3/7/13 7:57:32.665 PM
SecurityAgent[5231]
Problem during create from (builtin:login)
Now here is some additional info from the logs that appears to my novice eyes to be presenting a problem:
<D:multistatus xmlns:D="DAV:" xmlns:caldav="urn:ietf:params:xml:ns:caldav" xmlns:cs="http://calendarserver.org/ns/" xmlns:ical="http://apple.com/ns/ical/">
<D:response xmlns:carddav="urn:ietf:params:xml:ns:carddav">
<D:href>/calendar/dav/</D:href>
<D:propstat>
   <D:status>HTTP/1.1 200 OK</D:status>
   <D:prop>
    <D:current-user-principal>
     <D:unauthenticated/>
    </D:current-user-principal>
   </D:prop>
</D:propstat>
</D:response>
</D:multistatus>]
3/7/13 7:50:47.525 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [<<<<<]
3/7/13 7:50:47.525 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.queue] [Account refresh failed with error: Error Domain=CoreDAVHTTPStatusErrorDomain Code=401 "The operation couldn’t be completed. (CoreDAVHTTPStatusErrorDomain error 401.)" UserInfo=0x7fe2dff032f0 {AccountName=Google, CalDAVErrFromRefresh=YES, CoreDAVHTTPHeaders=<CFBasicHash 0x7fe2dff0f6d0 [0x7fff71512fd0]>{type = immutable dict, count = 10,
entries =>
          0 : Case Insensitive Key: X-Content-Type-Options = <CFString 0x7fe2dff0e960 [0x7fff71512fd0]>{contents = "nosniff"}
          1 : Case Insensitive Key: Content-Type = <CFString 0x7fe2dff0f100 [0x7fff71512fd0]>{contents = "application/vnd.google.gdata.error+xml; charset=UTF-8"}
          2 : Case Insensitive Key: Server = <CFString 0x7fe2dff0f510 [0x7fff71512fd0]>{contents = "GSE"}
          3 : Case Insensitive Key: Transfer-Encoding = <CFString 0x7fff719196f8 [0x7fff71512fd0]>{contents = "Identity"}
          6 : Case Insensitive Key: Date = <CFString 0x7fe2dff0f150 [0x7fff71512fd0]>{contents = "Fri, 08 Mar 2013 02:50:46 GMT"}
          7 : Case Insensitive Key: X-Frame-Options = <CFString 0x7fe2dff0f480 [0x7fff71512fd0]>{contents = "SAMEORIGIN"}
          8 : Case Insensitive Key: X-XSS-Protection = <CFString 0x7fe2dff0f4f0 [0x7fff71512fd0]>{contents = "1; mode=block"}
          9 : Case Insensitive Key: Www-Authenticate = <CFString 0x7fe2dff0efd0 [0x7fff71512fd0]>{contents = "basic realm="Google APIs""}
          11 : Case Insensitive Key: Cache-Control = <CFString 0x7fe2dff0f1b0 [0x7fff71512fd0]>{contents = "private, max-age=0"}
          12 : Case Insensitive Key: Expires = <CFString 0x7fe2dff0f180 [0x7fff71512fd0]>{contents = "Fri, 08 Mar 2013 02:50:46 GMT"}
3/7/13 7:50:47.566 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [<<<<<]
3/7/13 7:50:47.567 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [HTTP/1.1 200 (OK)]
3/7/13 7:50:47.567 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Age: 0]
3/7/13 7:50:47.568 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Allow: MKCOL, REPORT, MOVE, COPY, HEAD, POST, GET, DELETE, ACL, MKCALENDAR, PROPFIND, LOCK, OPTIONS, PUT, PROPPATCH, UNLOCK]
3/7/13 7:50:47.568 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Cache-Control: private]
3/7/13 7:50:47.569 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Connection: keep-alive]
3/7/13 7:50:47.569 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Content-Type: text/plain; charset=utf-8]
3/7/13 7:50:47.569 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Date: Fri, 08 Mar 2013 02:50:47 GMT]
3/7/13 7:50:47.570 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [DAV: 1, 2, 3, access-control, calendar-access, version-control, addressbook, extended-mkcol, calendar-proxy, calendarserver-principal-property-search]
3/7/13 7:50:47.570 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Server: YTS/1.19.11]
3/7/13 7:50:47.570 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Transfer-Encoding: Identity]
3/7/13 7:50:47.571 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Vary: Accept-Encoding]
3/7/13 7:50:47.571 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Via: HTTP/1.1 calgate007.cal.sp2.yahoo.com (YahooTrafficServer/1.19.11 [c sSf ])]
3/7/13 7:50:47.571 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] []
3/7/13 7:50:47.576 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.queue] [CalDAVAccountRefreshQueueableOperation :: calendar home path is empty, not refreshing calendars]
3/7/13 7:50:47.582 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [>>>>>]
3/7/13 7:50:47.582 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [PROPFIND https://caldav.calendar.yahoo.com/principals/users/saab9.5turbo/]
3/7/13 7:50:47.582 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Brief: t]
3/7/13 7:50:47.582 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Content-Length: 130]
3/7/13 7:50:47.583 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Content-Type: text/xml]
3/7/13 7:50:47.583 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Depth: 0]
3/7/13 7:50:47.583 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [User-Agent: Mac OS X/10.8.2 (12C60) CalendarAgent/55]
3/7/13 7:50:47.583 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] []
3/7/13 7:50:47.583 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [<?xml version="1.0" encoding="UTF-8"?>
<A:propfind xmlns:A="DAV:">
<A:prop>
    <A:group-membership/>
</A:prop>
</A:propfind>]
3/7/13 7:50:47.584 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] []
3/7/13 7:50:47.584 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [>>>>>]
3/7/13 7:50:48.101 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [<<<<<]
3/7/13 7:50:48.101 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [HTTP/1.1 401 (Unauthorized)]
3/7/13 7:50:48.102 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Cache-Control: no-store]
3/7/13 7:50:48.102 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Connection: close]
3/7/13 7:50:48.102 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Content-Language: en]
3/7/13 7:50:48.102 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Content-Length: 1]
3/7/13 7:50:48.103 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Content-Type: text/html]
3/7/13 7:50:48.103 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Date: Fri, 08 Mar 2013 02:50:48 GMT]
3/7/13 7:50:48.103 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Server: YTS/1.19.11]
3/7/13 7:50:48.104 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Via: HTTP/1.1 calgate009.cal.sp2.yahoo.com (YahooTrafficServer/1.19.11 [c s f ])]
3/7/13 7:50:48.104 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [Www-Authenticate: Basic realm="Zimbra"]
3/7/13 7:50:48.104 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] []
3/7/13 7:50:48.104 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] []
3/7/13 7:50:48.104 PM          CalendarAgent[3308]          [com.apple.calendar.store.log.caldav.http] [<<<<<]
3/7/13 7:50:49.202 PM          MacPilot[4054]          A regular control size progress indicator <RBXProgressWheel: 0x212bf20> with the frame size for small control size detected. Please use -setControlSize: to explicitly specify NSSmallControlSize
3/7/13 7:51:00.584 PM          SecurityAgent[3818]          Problem during create from (builtin:login)
3/7/13 7:51:00.584 PM          SecurityAgent[3818]          Problem during create from (builtin:login)
And some more:
Mar 7 20:51:07 Matthews-MacBook-Pro.local WindowServer[3177]: CGXGetConnectionProperty: Invalid connection 57091
Mar 7 20:51:37 --- last message repeated 8 times ---
Mar 7 20:53:14 Matthews-MacBook-Pro.local com.apple.SecurityServer[15]: Succeeded authorizing right 'system.hdd.smart' by client '/Library/Application Support/iStat Menus 4/iStatMenusDaemon' [104] for authorization created by '/Library/Application Support/iStat Menus 4/iStatMenusDaemon' [104] (B,0)
Mar 7 20:53:14 Matthews-MacBook-Pro.local com.apple.SecurityServer[15]: Succeeded authorizing right 'system.hdd.smart' by client '/Library/Application Support/iStat Menus 4/iStatMenusDaemon' [104] for authorization created by '/Library/Application Support/iStat Menus 4/iStatMenusDaemon' [104] (B,0)
Mar 7 20:53:44 --- last message repeated 2 times ---
Mar 7 20:58:25 Matthews-MacBook-Pro.local CVMServer[114]: Check-in to the service com.apple.cvmsCompAgent_x86_64 failed. This is likely because you have either unloaded the job or the MachService has the ResetAtClose attribute specified in the launchd.plist. If present, this attribute should be removed.
Mar 7 20:58:25 Matthews-MacBook-Pro.local CVMServer[114]: Check-in to the service com.apple.cvmsCompAgent_x86_64 failed. This is likely because you have either unloaded the job or the MachService has the ResetAtClose attribute specified in the launchd.plist. If present, this attribute should be removed.
Mar 7 20:59:04 Matthews-MacBook-Pro.local Finder[3247]: CFPropertyListCreateFromXMLData(): Old-style plist parser: missing semicolon in dictionary on line 1. Parsing will be abandoned. Break on _CFPropertyListMissingSemicolon to debug.
Mar 7 21:03:05 Matthews-MacBook-Pro.local Finder[3247]: CFPropertyListCreateFromXMLData(): Old-style plist parser: missing semicolon in dictionary on line 1. Parsing will be abandoned. Break on _CFPropertyListMissingSemicolon to debug.
I can't reinstall ML, nor can I create another user (unless I use Terminal, and I'm a novice at best with Terminal).
I could really use some help here as it's been nearly 24 and I am going CRAZY!   Thanks in advance for your help.

UPS and our iMac // Will not allow iMac to sleep.

Hello,
We have a Cyberpower UPS (CP685AVR) for our 20" iMac 2.66Ghz (last gen)and it works great. It has a USB interface to communicate with the iMac's power manager, and tells me how much juice is left, how the cells are doing, etc.
The only problem is the UPS will not allow the iMac to sleep; if I try to manually put it to sleep, it will wake again in 10-15sec. If I disconnect the UPS, the iMac works just fine. There are no third-party drivers, either. Cyberpower relies on Apple's built-in UPS support. I've been leaving the USB cable unplugged but would like like to use it if possible.
Has anyone had an issue like this, and what has been your experience? Thanks.

I won't buy Cyberpower anymore since I had one burn up on me so I have not had any experience with their newer models. I have 2 APC's and they work fine with the built in Energy Saver settings.
Are you connecting the USB directly to the back? I'm not sure if it will help but you might try resetting the SMC: http://support.apple.com/kb/HT1543?viewlocale=en_US
George

HP P1102w printer will not wake up after sleep (wireless setup, win8)

Bought this printer a month ago. I have no problem with both LAN +Wireless setup.
Windows8 OS
I noticed once the printer is not on (goes to sleep), it will not wake up by itself.
According to manual, if I send a print job, it should wake up by itself.
Currently, this is what I need to do.
I need to physically turn off and turn on the printer, wait for 10-15 seconds until the wifi blue light is solid (no blinking)
and then send my print job, and it will work
Just wondering whether HP has a solution to this, thanks
This question was solved.
View Solution.

Is HP ever going to fix / address this issue?
People Running the latest firmware - 20130703
And there is no option to disable Sleep mode. The max you can set it to is 1 hour.
The power physically / manually has to be powered back on, to establish IP connectivity.
This has been an issue for 2 years now!!! Come on what does it take to get an update?
Seriously?

AppleTV3 will not act as Bonjour sleep proxy

Similar Messages

Maybe you are looking for