Application Nividia Stream error and warning in the Event Viewer Windows 8.1

Have found the following repeating error and warning in the Event Viewer Windows 8.1 64 bit reg.the application Nividia Stream:
1. The error :
"Can not find the description of event 2001 identification from
the source NvStreamSvc.
Either the component causing this issue is not
installed in the local computer or installation is broken. You can install or
repair the component in the computer.
Information to the event :
NvStreamSvc
Failed continue stopping [6] "
2. The warning :
"Can not find the description of event 2002 identification
from the source NvStreamSvc.
Either the component causing this issue is not
installed in the local computer or installation is broken. You can install or
repair the component in the computer.
Information to the event
NvStreamSvc
SSAU process ID 7820 did not exit, Termination.
[6]”
I would appreciate the advice how to fix it.
Thanks and best regards,
Ewa

Hi,
Thanks for your reply.
Have the lastest updated Nividia driver : version 347.88 - shall I uninstall and install again ?
Shall I make express installation /as usually/ or advanced ?
Reg. Nividia Stream service - shall I disable this service in services.msc ?
The software - now have Nividia GeForce Experience updated to the version 2.4.1.21 on 30th
March.
Would appreciate your further assistance and help.
Thanks and best regards, Ewa

Similar Messages

Intranet DOWN!! Help, please!! I installed SP2010 SP2 and the Configuration Wizard Stopped at Step 5. I found errors 100 and 104 in the Event Viewer!

Hi,
Help, please.
Intranet DOWN!! Help, please!! I installed SP2010 SP2 and the Configuration Wizard Stopped at Step 5. I found errors 100 and 104 in the Event Viewer!
Acording to these entries:
http://blogs.technet.com/b/sbs/archive/2011/08/19/two-commands-you-should-always-run-first-when-troubleshooting-companyweb.aspx
https://translate.google.com/translate?hl=en&sl=auto&tl=en&u=http%3A%2F%2Fwww.techtask.com%2Fsharepoint2010%2Ffehlermeldungen-nach-sharepoint-2010-service-pack-1-installation%2F
In order to fix this, I need to run:
PSConfig.exe -cmd upgrade b2b -force -inplace -cmd application content -install -cmd install features
But SP doesn’t recognize “b2b”. is the the content or config db?
Thanks in advanced

Your Syntax is bad. b2b should follow -inplace, it doesn't make sense anywhere else in the command. Have a look here for more detail:
https://technet.microsoft.com/en-us/library/cc263093%28v=office.14%29.aspx?f=255&MSPPError=-2147217396

I've cleared almost 30 gig off of my hard drive in the past 2 weeks, and it will temporarily show that in the Get Info box. But hours later, I am still getting a disk full error and all of the memory has disappeared.

I've cleared almost 30 gig off of my hard drive in the past 2 weeks, and it will temporarily show that in the Get Info box. But hours later, I am still getting a disk full error and all of the memory has disappeared. I have cleared my backup logs from Time Machine, checked the mail folder, cleaned out tons of photos and videos and it still keeps filling back up.
In checking the log files, here is the message repeated over and over....
Jul 4 07:18:13 Donald-Keele-Jrs-iMac-123.local CalendarAgent[213]: CoreData: error: (21) I/O error for database at /Users/donjr/Library/Calendars/Calendar Cache. SQLite error code:21, 'unable to open database file'
Jul 4 07:18:13 Donald-Keele-Jrs-iMac-123.local CalendarAgent[213]: Core Data: annotation: -executeRequest: encountered exception = I/O error for database at /Users/donjr/Library/Calendars/Calendar Cache. SQLite error code:21, 'unable to open database file' with userInfo = {
NSFilePath = "/Users/donjr/Library/Calendars/Calendar Cache";
NSSQLiteErrorDomain = 21;
Jul 4 07:18:14 Donald-Keele-Jrs-iMac-123.local cfprefsd[180]: CFPreferences: error creating file /Users/donjr/Library/Preferences/com.apple.iPhoto.plist.t3l894p: 28
Jul 4 07:18:30 Donald-Keele-Jrs-iMac-123.local Printer Pro Desktop[275]: Empty task
Jul 4 07:18:33 Donald-Keele-Jrs-iMac-123.local Microsoft Sync Services[8149]: [0x16697c0] |ISyncSession|Warning| com.microsoft.Entourage2008: transitioning to cancel - session cancelled by server: Client 'com.microsoft.Entourage2008' tried to start a session for the plan 45AD80C3-0D52-4CF2-8CBA-103564B6C47C and the plan no longer exists.
Jul 4 07:18:33 Donald-Keele-Jrs-iMac-123.local Microsoft Sync Services[8149]: Warning: NSBundle NSBundle </Applications/Microsoft Office 2008/Office/Microsoft Sync Services.app/Contents/Resources/MicrosoftOfficeNotes.syncschema> (not yet loaded) was released too many times. For compatibility, it will not be deallocated, but this may change in the future. Set a breakpoint on __NSBundleOverreleased() to debug
Jul 4 07:18:33 Donald-Keele-Jrs-iMac-123.local Microsoft Sync Services[8149]: Warning: NSBundle NSBundle </Users/donjr/Library/Sync Services/Schemas/MicrosoftOfficeNotes.syncschema> (not yet loaded) was released too many times. For compatibility, it will not be deallocated, but this may change in the future. Set a breakpoint on __NSBundleOverreleased() to debug
Jul 4 07:18:45 Donald-Keele-Jrs-iMac-123 kernel[0]: (default pager): [KERNEL]: default_pager_backing_store_monitor - send LO_WAT_ALERT
Jul 4 07:18:45 Donald-Keele-Jrs-iMac-123 kernel[0]: macx_swapoff SUCCESS
Jul 4 07:19:31 Donald-Keele-Jrs-iMac-123.local Printer Pro Desktop[275]: Empty task
Any ideas on what to do next?
I'm running and iMac 20-inch early 2009
Processor 2.66 GHz Intel Core 2 Duo
Memory 8 GB 1067 MHz DDR3
Graphics NVIDIA GeForce 9400 256 MB
Software OS X 10.8.4 (12E55)

Step 1
Quit Calendar. Triple-click the line below to select it:
~/Library/Calendars/Calendar Cache
Right-click or control-click the highlighted line and select
Services ▹ Reveal
from the contextual menu. A Finder window should open with a file named "Calendar Cache" selected.
Move the selected file to the Trash. There may be one or two other files in the same folder with names that begin in "Calendar Cache". If so, delete those files too.
Step 2
Empty the Trash if you haven't already done so. If you use iPhoto, empty its internal Trash as well:
iPhoto ▹ Empty Trash
Then reboot. That will temporarily free up some space.
According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation. You also need enough space left over to allow for growth of your data. There is little or no performance advantage to having more available space than the minimum Apple recommends. Available storage space that you'll never use is wasted space.
To locate large files, you can use Spotlight. That method may not find large folders that contain a lot of small files.
You can more effectively use a tool such as OmniDiskSweeper (ODS) to explore your volume and find out what's taking up the space. You can also delete files with it, but don't do that unless you're sure that you know what you're deleting and that all data is safely backed up. That means you have multiple backups, not just one.
Deleting files inside an iPhoto or Aperture library will corrupt the library. Any changes to a photo library must be made from within the application that created it. The same goes for Mail files.
Proceed further only if the problem isn't solved by the above steps.
ODS can't see the whole filesystem when you run it just by double-clicking; it only sees files that you have permission to read. To see everything, you have to run it as root.
Back up all data now.
Install ODS in the Applications folder as usual. Quit it if it's running.
Triple-click the line of text below to select it, then copy the selected text to the Clipboard (command-C):
sudo /Applications/OmniDiskSweeper.app/Contents/MacOS/OmniDiskSweeper
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V). You'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning not to screw up. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
The application window will open, eventually showing all files in all folders. It may take some minutes for ODS to list all the files.
I don't recommend that you make a habit of doing this. Don't delete anything while running ODS as root. If something needs to be deleted, make sure you know what it is and how it got there, and then delete it by other, safer, means. When in doubt, leave it alone or ask for guidance.
When you're done with ODS, quit it and also quit Terminal.

XML page cannot be displayed cannot view XML input using XSL style sheet Please correct the error and then click the REfresh

XML page cannot be displayed cannot view XML input using XSL style sheet Please correct the error and then click the REfresh

Is the error message displayed in Firefox or in IE, or in a customized window that doesn't identify the browser?
''If it displays in Firefox:''
It's possible that the Troubleshooter doesn't work correctly unless IE is your default browser. You could test that possibility by having IE make itself the default and testing the Troubleshooter again.
''If it displays in IE or embedded in another Microsoft application:''
In a web search I found these suggestions:
(1) Reset your Internet Explorer settings, according to http://answers.microsoft.com/en-us/ie/forum/ie8-windows_7/cannot-view-xml-using-xsl-style-sheet/ccfe80c6-c0db-4594-a7e3-475f9eac0e85
(2) Try the System File Checker, according to http://ask-leo.com/why_do_i_get_the_xml_page_cannot_be_displayed_after_running_a_microsoft_troubleshooter.html
Any luck?

Since trying to update yesterday, my computer won't download any updates and itunes 11.1 says "Internal Error" and gives me the following info when I click on a song or podcast: Exception Name: NSInvalidArgumentException Description: -[_NSConcreteUserNoti

Since trying to update yesterday, my computer won't download any updates and itunes 11.1 says "Internal Error" and gives me the following info when I click on a song or podcast:
Exception Name: NSInvalidArgumentException
Description: -[_NSConcreteUserNotification activationType]: unrecognized selector sent to instance 0x25a06b0
User Info: (null)
0   CoreFoundation                      0x922216fb __raiseError + 219
1   libobjc.A.dylib                     0x920108db objc_exception_throw + 230
2   CoreFoundation                      0x9222563d -[NSObject(NSObject) doesNotRecognizeSelector:] + 253
3   CoreFoundation                      0x9216af77 ___forwarding___ + 487
4   CoreFoundation                      0x9216ad22 _CF_forwarding_prep_0 + 50
5   iTunes                              0x00df38e2 iTunes + 14624994
6   iTunes                              0x00df36ae iTunes + 14624430
7   libobjc.A.dylib                     0x9201c6c5 -[NSObject performSelector:withObject:withObject:] + 77
8   Foundation                          0x93c12d85 -[_NSConcreteUserNotificationCenter _sendDelegateMessage:sendToAppDelegate:withNotificationFromMessage:] + 335
9   Foundation                          0x93c12eaf -[_NSConcreteUserNotificationCenter _notificationPresentedMessage:] + 58
10 Foundation                          0x93c137c2 __block_global_1 + 156
11 libdispatch.dylib                   0x9371b2cf _dispatch_call_block_and_release + 15
12 libdispatch.dylib                   0x9371ea80 _dispatch_client_callout + 46
13 libdispatch.dylib                   0x9371c8e8 _dispatch_main_queue_callback_4CF + 223
14 CoreFoundation                      0x9211b255 __CFRunLoopRun + 1829
15 CoreFoundation                      0x9211a7c4 CFRunLoopRunSpecific + 308
16 CoreFoundation                      0x9211a67b CFRunLoopRunInMode + 123
17 HIToolbox                           0x90b6fc76 RunCurrentEventLoopInMode + 242
18 HIToolbox                           0x90b76eb9 ReceiveNextEventCommon + 374
19 HIToolbox                           0x90b76d34 BlockUntilNextEventMatchingListInMode + 88
20 AppKit                              0x97621923 _DPSNextEvent + 709
21 AppKit                              0x97621167 -[NSApplication nextEventMatchingMask:untilDate:inMode:dequeue:] + 119
22 AppKit                              0x9761d78c -[NSApplication run] + 855
23 iTunes                              0x0017a898 iTunes + 1546392
24 iTunes                              0x0017a709 iTunes + 1545993
25 ???                                 0x00000002 0x0 + 2

Please read this whole message before doing anything.
This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
Step 1
The purpose of this step is to determine whether the problem is localized to your user account.
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your personal files or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Step 2
The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, or by corruption of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of steps 1 and 2.

ACPI Error and warning

Hi everyone,
I just switched over from Ubuntu 14.04 after installing a new hard drive on my Samsung 900x3c. I did a clean Arch install with Lxqt as my desktop and in an attempt to get all the function keys working and installing samsung-tools I discovered a couple of errors and warnings in the dmesg output related to AE_NOT_FOUND as well as conflict between the systemIO range and the OpRegion. Now I would really like to remove these errors/warnings even though for the moment apart from the missing function keys (which might even be unrelated) I do not have any major side effects. The output of dmesg -t | grep -i 'error\|warn\|exception' is:
ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20141107/hwxface-580)
acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042f conflicts with OpRegion 0x0000000000000400-0x000000000000047f (\PMIO) (20141107/utaddress-258)
ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054f conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20141107/utaddress-258)
ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053f conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20141107/utaddress-258)
ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052f conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20141107/utaddress-258)
ACPI Warning: SystemIO range 0x000000000000efa0-0x000000000000efbf conflicts with OpRegion 0x000000000000efa0-0x000000000000efaf (\_SB_.PCI0.SBUS.SMBI) (20141107/utaddress-258)
Any ideas?
Thanks a lot in advance and best regards,
S

You can ignore those.
If you look at the journal entries around those lines you'll get more context for those messages.
The first one is part of the probing to find supported sleep states. Your system doesn't support the S2 sleep state.
The second is caused by your system's firmware not allowing the OS to use ASPM (Active State Power Management) to control the power mode of the PCI Express bus/devices. There can be lots of reasons for that - e.g. no support in firmware, firmware deliberately not allowing OS control, bug in firmware, specific manual settings have been set in the firmware, etc. Unless you care about the power management of PCI Express devices, just ignore the message. Otherwise, check the PCI Express power settings (if available) in your system's firmware, alternativelyi there may be a newer firmware - if there is, see what the changes are to determine if updating will help.
for the ACPI warnings see https://bbs.archlinux.org/viewtopic.php?id=163556

Window Errors and Warning in this Transaction not shown

We're using Designer 6.5.82.3.0.
Business rules aren't generated according to CDM Ruleframe, no CAPI. But Table API/trigger logic.
=> Pre-Before-Insert-Row
BEGIN
if CDR_CPN.F_CPN_UNIQUE(:new.CODE)
then
-- a new code
null;
else
-- code already exists
QMS$ERRORS.SHOW_MESSAGE
('CDR-05000'
,:new.CODE);
end if;
END;
When an business rule fails the window Errors and Warning in this Transaction with the error-message is not shown. Instead we get the message Transaction failed
(when using sqlplus the same message appears, then running @messages.sql =>correct message)
According to a previous discussion the ON-ERROR of the module component should be modified (author Bart van Ges 22 May 2002). And this works, the window Errors and Warning in this Transaction is shown with the correct message.
Has anyone another solution, patch or any idea why the window doesn't appear without the modification?
Cheers,
Bob

All,
Since Headstart for 6.0 (patch 12) and Headstart for 6i, Headstart default only functions well in combination with CDM RuleFrame. If you want to deviate from this standard, the functionality in the libraries should be adapted for this purpose. There are several ways to do this:
- show serverside errors in an error Alert window
- show serverside errors in the RuleFrame transaction and errors window.
Whatever approach you choose - in this thread several suggestions are being made - it is not documented in headstart how to do this. The Oracle Headstart group is not able at this moment to investigate time to workout the alternatives, though I will add an enhancement request to headstart to document these options in the headstart user guide.
Two extra suggestions:
- try to test your workaround as well as possible (try to raise errors from server, client, try to violate server constraints (pk, uk, fk, ck) and try to let serverside pl/sql fail.
- if you do not make use of ruleframe, you might run into a problem if you try to commit in the serverside logic, in this case remove the calls in the template package (qms$even_form) to open and close the transaction (pre-commit and post-forms-commit trigger events).
Regards,
Marc Vah[i]Long postings are being truncated to ~1 kB at this time.

Error and warning message querry?

How is it that i can see in spro all the error and warning messages???

Hi,
in table t100 through se11 i can see the field MSGNR , THATS IT ,

How to stream Webcam and Desktop at the same time?

Hey Guy,
I just got a little Problem with FMLE... I want to stream live during a Game, but I dont know how to stream Desktop and Webcam at the same time ^^. The streaming Platform i want to use is twitch.tv.. the most common Gamin Platform I think...
I got an IMac i7.
Pls help me I dont get how all these ProGamer do it -.-
Thanks in advance
Kathi

You're going to need additional software or hardware. If you're running a Macintosh, try CamTwist. It's free and allows you to create virtual "cameras" from just about anything you can see on your computer. It's a bit clunky getting used to the interfact and how it works, however.
Hardware solutions (like scanline converters and video switchers) can get pretty expensive. So you may want to go with a piece of software that can handle on-the-fly video compositing/switching. There are two applications that come to mind right off the bat -- and lucky for you, both of them can also output to a live streaming server.
Wirecast is a popular choice, although the pricing starts around $500. It's Macintosh/Windows.
A very popular choice among gamers is XSplit (Windows only) and is a subscription-based model (you pay a small fee by the month, quarter, or year). XSplit has some very impressive compression happening under the hood, and was originally designed for gamers who wanted to share their desktop, XBOX, or PS3 adventures... all while also being able to lay over banners, PIP (picture-in-picture) of themselves, or anythhing else they wanted to clutter the screen with.
If you're running on Windows, give XSplit at shot. It can easily handle your desktop (or most anything else) as a "camera" as well as being able to lay your webcam on top of the desktop feed.

How do i get my photos to stream to my iPad in the events that were oringally created. Right now they are streaming as photos and are not grouped at all. I would like to get them back into the events that were originally created

how do i get my photos to stream to my iPad in the events that were oringally created. Right now they are streaming as photos and are not grouped at all. I would like to get them back into the events that were originally created

Hi..
Thanks for the reply..
My original I Phone 5 was running IOS 6.12
My I phone 5S currently runs IOS 8..When I upgraded it, it had IOS 7 on it which made the I Photo app compatible with everything below IOS 8...( which the photo app is not compatible with ) so I just connected the I Phone 5S to my computer and thinking the new phone had IOS 7 on it that these was nothing to worry about..I thought all 900 + pictures in the photo stream would transfer but somewhere in the process, I Tunes decides to just go and install IOS 8 which requires that you run a " Photo Migration App" to transfer photos from IOS 7 & below. The problem was is that I didn't want IOS 8 on my new 5S so I thought I wouldn't have to do that part..
Anyway the phone emerged with IOS 8 on it and the only photos that remained were the ones that were actually on the phone..The 900 + I had in the stream didn't transfer because the Photos that works on IOS 7 and below isn't compatible with IOS 8..I guess you have to use the photo migration app that comes with IOS 8 & I phone 6..But I didn't ask to upgrade to IOS 8...It just did it on it's own!
I still have the I Phone 5 Back up that I did just before giving it back to Verizon but if I try to restore the I Phone 5S running IOS 8 those photos in the stream will not go back on the phone because IOS 8 isn't compatible with the I Photos" that ran on IOS 7 and below..
So I have an I Pad mini that runs IOS 7..should I try and erase it...and put that I Phone 5 backup on it and pray the photos that were in the stream come back on it so I can transfer them back to my computer...then erase the I pad mini again and restore it using it's original backup that I have on the computer and the in the cloud?
I know this sounds confusing but I'm at a loss as to what to do..This is what I found ...http://support.apple.com/en-us/HT201386
but it doesn't help me..
Steve

I have completely lost my safari. I was getting an error and I lost the address bar. I tried to fix it by changing the home page on the preferences. I don't know what to put in the home page now. How do I get safari back?

I have completely lost my safari. I was getting an error and I lost the address bar. I tried to fix it by changing the home page on the preferences. I don't know what to put in the home page now. How do I get safari back?

I tried editing my first post but couldn't get there...
If you can open Safari go to the top of your screen, click Safari / Preferences then select the General stab. You can type in the web address for your Home page there.

Streaming wifi and bluetooth at the same time is it possible in air play from iPod

Streaming bluetooth and wifi at the same. Is it possible?

You are not able to send the music to two different streams, you can use the bluetooth and wireless at the same time but for different tasks.
The best way I have seen for what you are attempting, is to buy a wired splitter and two bluetooth transmitters, and have each transmitter broadcast bluetooth sound to the two different locations.
I have not found any other way except when using itunes on a desktop computer which allows the selection of multiple output destinations.

Converted vinyl to digital but now when I try to burn the music to a cd it says there is a writing error and kicks out the disc.

Just converted a bunch of my dad's old vinyl to digital via the ion ez vinal converter. However when I went to burn the music, which sound fine over the computer, to a cd it says there is a writing error and kicks out the disc. Can I correct this somehow without having to import these all again?

Update yrou OS to 10.6.8.
The problem is not with iTunes or the file so you won't need to import them again.
Try a different brand of disc.

HT4740 i already did the Hidding part and later moved the events and projects to the FCP events and projects folder . I still cannot share - keep getting this message "THE SHARE OPERATION 1080P FOR APPLE DEVICES (10 MBPS) HAS FAILED. Quicktime Error -50

i already did the Hidding part and later moved the events and projects to the FCP events and projects folder . I still cannot share - keep getting this message "THE SHARE OPERATION 1080P FOR APPLE DEVICES (10 MBPS) HAS FAILED. Quicktime Error -50
I dont know what else to do to be able to share my project - I know i updated FCPX before i shared this project but i dont know what im doing wrong

masterpieces wrote:
later moved the events and projects to the FCP events and projects folder .
Can you explain in detail what you did?
Do any other shsre destinations complete? If not, do you get the same error message?

PPT has found an error and cannot save the file in Microsoft Powerpoint2010

I have been working in 2010 for 6 months and this is the 3rd time I have experienced this error. I am using my own 2010- created, macro-enabled template - I want to save the file but I get an error message stating PPT
has found an error and cannot save the file.
This has happened on both newly created files using this template, and files previously successfully saved. The template has been used without error many, many times.
I have on occassion been able to save as a 97-2003 file and then resave (with some loss of function) as a 2010 macro-enabled file, on another occassion I was not able to do this and lost some work.
Copying into a new document didn't solve the problem. Copying into a different template didn't solve the problem.
Any ideas what is happening, and how I can stop it happening?
Kind regards

Hi,
Have you tried saving the file in *.pptm format (basically this extension is for powerpoint presentation with macros)
Maybe try Save As and see if you can save it under a different name.
Once you get the file closed, then reopen PPT and go to Office Button | PPT Options | Resources. Run Office Diagnostics there.
In addition, make sure you have a local printer driver installed and set as the default printer. And it really might fix the issue.
Here's info on what to do:http://www.pptfaq.com/FAQ00952.htm
Sincerely

Application Nividia Stream error and warning in the Event Viewer Windows 8.1

Similar Messages

Maybe you are looking for