Application video out

I am building an iPhone application and would like a demo video. Ideally I would like to connect my phone to my tower and have the tower record my iPhone screen while i play with the application. Is this at all possible?

thanks for the quick reply

Similar Messages

  • I want to play video on my computer to make some analysis to frames,the problem that I face ,I can't change video frame rate using labview,but I can change frame rate to the video out of labview using some program

    HI All
    I want to play video on my computer to make some analysis to it's frames,the problem that I face ,I can't change video frame rate using labview,but I can change frame rate to the video out of labview using some program .
    I used IMAQ AVI Read Frame VI
    for example I have avi video It's frame rate is 25 fbs ,my image processing code is very fast that can process more 25 fbs,so I want to accelerate video acquisition

    Hi abdelhady,
    I looked into this further, and reading an AVI file into LabVIEW faster than its frames per second won't be possible. LabVIEW could read in frames faster than 25fps, but because it will be pulling the available frame at that point in time this would just give you duplicate frames. If you want to be able to read in frames at faster than 25fps, you would need to speed up your AVI file before reading into LabVIEW.
    There's a good shipping example to show how to read in from an AVI file, "Read AVI File.vi". You'll notice that they add timing to make sure that the while loop runs at the right speed to match up with the frames per second of the file being read. This is to make sure you're not reading duplicate frames.
    Thank you,
    Emily C
    Applications Engineer
    National Instruments

  • Looking for an app that combines an equalizer with video out.

    I'm looking for an app that has video out (like "Upsize" or the iPod built-in photo slideshow) with an equalizer (preferably like "Denon Audio" or "EQ Pro" so that I can listen to equalized music through my TV. Upsize is close, as it allows for album art to be displayed on my TV while the music plays however, it does not control volume and you must use the iTunes equalizer before you start the app. My TV is the type that will not play audio without an accompanying video signal when using a component cable to connect my iPod to the TV inputs.

    Hi ron1098,
    Try my application Dates to iCal. it runs on the Mac, but you can sync the calendar to your iOS device.
    See more about Dates to iCal here. It is £4 shareware with a 2 week demo.
    Best wishes
    John M
    As I sell software on my site and ask for donations, the Apple Support Communities Use Agreement requires that I state that I may receive some form of compensation, financial or otherwise, from my recommendation or link.

  • 3rd generation iPod Touch and Video Out - "whoops!!!"

    Before I jump to any conclusions about Apple, here is my experience with the Video out operation of my brand new 3rd generation 64 GB iPod Touch. This is my third iPod and about a year ago I decided (at great personal expense) to purchase the Apple Composite AV Cable (despite the fact that you can buy copies of the cable on eBay for 1/10th the price). When I plugged this cable into my new iPod touch, the Video Out option was greyed out. I tried lots of different things but eventually gave up and went to the Apple Store to see what it said about compatability. Sure enough, the 3rd Generation Touch is the ONLY iPod, iPhone etc not mentioned. I call my friendly apple support person who says "*of course it will work, I am 100% sure*". I then jokingly asked if he would give me $1000 if he was wrong and begrudgingly he put me on hold "just to check". 15 minutes later (unusual for Apple) he came back to me saying that *I "might" be right but he was 100% sure that if I connected my cable via a Universal Dock it would work.*
    Now, before I go out and spend any more money on a Universal Dock, has anybody tried this? Why would apple make the change ONLY to the 3rd Gen iPod touch?
    I have noticed that there is one nasty non-apple cable on the market that claims it will work BUT it doesn't have the ability to charge...... besides I ONLY buy legit Apple products.
    Any comments?

    Wow Apple pulled tha last post almost as quick as it was written.
    I have been in the IT industry for 18 years, when I started out I read the Mac bible and got a job supporting 1000 macs (remember the wonderful days of the symbol of the little bomb and all you could do is re-install the OS - what a joke). We ditched the Mac due to limited application support (nothing has changed much has it). I did not look at another apple product for 15 years, got a Touch for free ( CC points) Firmware 2.2, loved the little bugger, had a whole new respect for Apple. Happily got 2 cables from eBay for $5.00 for both, video to the tv, charging, audio, best of all worlds. Then, I upgrade to version 3.01 for $5.00, what a deal, copy paste, etc. till I plug in my cables and nothing works anymore. Take it to the car for my FM receiver,. only mono now. Oh sorry you now have to dish out $50.00 for our cables (the /B version not the /A cause we even screwed our customers that bought our own cables) and oh ya you can only buy over priced FM receiver products that pay bloated license fees to Apple. Then we come to your story, you buy "Only Apple products" which do not work (check for the /A model of the cable, you need the /B (/B= Buy again?? Maybe) and then the support guy tells your to go out and spend yet another $50.00 on a universal dock and you are asking if you should do it. Sure spend another $50.00 for the chip enabled dock, it will work, hmm, I think I have put together a pc for less than $100.00

  • Video out to tape woes

    Now I have an HD TV I thought I'd try to output finished sequences back to the camera, to play on the TV via HDMI. But I can't get FCE (3.5.1) to write correctly to the camera, a Sony FX7E. Print to video just puts the colour bars and countdown onto tape, but no material, and playback of the timeline doesn't get to the camera either.
    My easy setup is HDV-Apple Intermediate Codec 1080i50, but the details in the easy setup dialogue state Playback Output Video:None. View/Video Out has these options:
    Canvas Playback - ticked, and three different digital cinema desktop options, all greyed out.
    So, help please - how can I write back out to tape? Indeed, CAN I?
    Thanks in advance,
    Alan
    Message was edited by: AtlanticView - after alt/F12 the three digital cinema desktop options are no longer greyed out.
    Message was edited by: AtlanticView

    Right now:
    Having booted:
    alan/library/preferences: NO com.apple.finalcutexpress.plist
    HD/library/preferences: YES com.apple.regfinalcutexpress.plist
    alan/library/preferences/final cut express user data:
    file: final cut express 3.5 prefs.fcset
    file: final cut express obj cache.fcmch
    file: final cut express prof cache.fcpch
    The last 2 were recreated when I reopened FCE last.
    I have never touched the fcset file, but its date and time = last time I opened FCE
    Now: I have just deleted fcmch and fcpch and opened FCE: yep, there are my favourites, and there are my rabbits hopping about!
    The three files mentioned just up there ^ are now dated and timed to NOW.
    Is there a ghost in my Mac? It looks like there is yes way the application can do this!! Reinstall?
    Alan
    (All capital letters ignored in folders/file names)

  • Powerbook 17" S-Video Out to TV monitor

    Hey all,
    If we go out of the S-Video out on a Powerbook 17" 1.5Ghz, and in to a television's Video In, is there a way to use the TV monitor for video only? Like how you can do that on a G5 tower, take the video out and make it extend your real estate.
    I don't want the TV screen to be a copy of what's already on the Powerbook's screen. I want to see Logic in the Powerbook, and the quicktime movie from Logic on the TV screen. Does anyone know if this is possible?
    Thanks in advance!
    ETMi

    I've done this with my powerbook, only I had the DVD player app on the TV, and was using the laptop LCD for other apps. It worked just fine. In fact I did it on two different TVs, once using s-video (w/optical sound out even) and once with DVI.
    I can't speak to your specifc application (Logic) but I don't know why it wouldn't work the same way.

  • Video out not working properly

    i recently bought the Gigaware Composite A/V Cable for my 3rd Gen iPod touch at Radio Shack. It works beautifully with youtube and both iTunes videos as well as ones i uploaded myself. i get full video and sound with these. But when i try to play music there is no sound, when i try to view pictures they do not come up and when i try to use the netflix app there is no sound. I know my version of iPod is not yet compatible with video out for the netflix app, but others are saying they get sound, i get nothing. is there a setting that i need to correct or some other way to fix this? I also have a 1st generation iPod touch, and i have the same issue with this one as well. Please help.

    The video only works with specific application. I would not expect music to one of those since there is no video in music. I know on the iPad photos do not display on video out (slide shows do). The same may apply for the iPod. I can't answer about the NetFlix no sound.
    An Apple Support page says the following so there may be difference in different manufacture's cables.
    Note: If you choose to use a third-party cable, make sure it has the "Works with iPhone" or "Made for iPod" label. Learn more about iPod and iPhone accessories.

  • Video out Ipad interface screen

    How can I use the iPad to project out the interface screen with the video out cable ? Is there an app I can use to do so ?

    This is not an option. VGA out only works within applications, and then only those that support is, like Keynote, NetFlix, a few browsers etc. Safari will not even project, I use Expedition.

  • Device that can split HDMI video out

    I'm starting here before i might get sold something that won't work...
    Am running a late-2012 i7 2.3 quad Mini in a studio.  I (will) have two matching Acer 24" LED
    monitors that need to display the same screen simultaneously- the 2nd monitor in an adjacent room.
    I was going to use Thunderbolt/MiniDisplayPort>DVI for that monitor but the Mini is maxed out - every
    port is being used for something and i need the TBolt for an audio device.  Hence am considering
    splitting the video out.  Question - will a passive "Y" type splitter work and does it put any extra drain
    on the Mini in a way that might 'tax' it too much -- or is there a powered device that would be better
    suited for this task and if so, any suggestions of a model or two that are known to be reliable?
    Also, would a passive splitter make the display on either of the monitors dimmer ?  I seem to recall
    somebody saying they had an issue where one or the other was less bright when using a splitter(?)
    Thanks for any info you might have!  Much appreciated!
    Mike

    Hi Gary, thanks for your reply.  My question then would be, of the fairly inexpensive 'active' devices pointed out in the comparison review mentioned earlier - i.e.  http://hdmi-switcher-review.toptenreviews.com/ 
    I wonder why any of those wouldn't serve my purposes fine - that is, a switcher.  Or alternately, perhaps there would be cheaper active  VGA (vs DVI) splitters for something in the realm of less than $100 that would do the trick.  For our needs,even if i needed to run VGA (which both monitors are capable of) it wouldn't be such a critical application that this would be a major factor - vs. the DVI..  I would just be going HDMI>VGA split box>two monitors
    I just recalled using a passive VGA splitter cable a couple of years ago on an old Mini now that i think about it - the resolutions matched on the two identical monitors - and both did display without distortion in that case. 
    Even though i believe there was a bit of a dimming effect on both, it wasn't so extreme that they weren't acceptable.  Still, i would buy an active powered splitter - just wonder if i wouldn't be fine to go with something in the under-100.00 set of options shown in the 'reviews' link and if not, what the problem could be. THanks!
    Mike

  • Buffering pauses and audio/video out of sync, single RTMP stream w/ simple embed

    Hello,
    I am running Flash Media Server on my dedicated CentOS host, and finally connected a single RTMP stream fine and am able to embed and play back the stream, but I am getting constant buffering pauses (approx every 5 secs) and audio/video out of sync by at least 5 seconds. My CPU with Flash Live Encoder is a powerhorse, never over 25% processor or ram usage while streaming, and my upload internet speed is averaging 6-8 mbps which should be more than adequate. I fear the issue is server side, however port 1935 is open and in use, not firewalled on CPU nor the host.
    Any suggestions would be great.

    Hello,
    Thanks for the reply, I am using embed code generated with Flash Media Playback, as follows:
    <object width="640" height="480"> <param name="movie" value="http://fpdownload.adobe.com/strobe/FlashMediaPlayback.swf"></param><param name="flashvars" value="src=rtmpt%3A%2F%2F50.62.40.55%3A1935%2Flive%2Fchristmastime&poster=http%3A%2F%2Fsq uarestream.ca%2Fpics%2Fframe.jpg&autoPlay=true&streamType=live&optimizeInitialIndex=false" ></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://fpdownload.adobe.com/strobe/FlashMediaPlayback.swf" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="640" height="480" flashvars="src=rtmpt%3A%2F%2F50.62.40.55%3A1935%2Flive%2Fchristmastime&poster=http%3A%2F% 2Fsquarestream.ca%2Fpics%2Fframe.jpg&autoPlay=true&streamType=live&optimizeInitialIndex=fa lse"></embed></object>

  • How to get video out to display menus and apps...

    I have a 'myvu for iPod', which is a little video screen in your glasses, and it displays "Videos" and "YouTube" clips fine but I can't seem to get it to display videos played in other applications like the 'TED' app, photos, cover art during music playback or the menus for navigation. How can I configure the IPod to play everything on the audio/video out instead of just YouTube and Videos?

    The ipod touch can only output youtube and movies at the moment on an external display.
    It's been complained about for some time
    Only thing that you can do for now is register your dissatisfaction at http://www.apple.com/feedback/
    Regards
    Paul

  • IMovie Problems: Photo import and audio-video out of sync.

    Photo import problem:
    Some times, I have problems importing photos onto my new project, the photos will appear to be that just one same photo when played. It does not transit to the other photos following the first, it's just stuck on the first. Is this just an issue with iMovie '11? Are there any other ways to resolve this problem?
    Audio-video out of sync:
    I've checked some other discussions but I'd like to raise this issue again for APPLE. There are problems exporting my 7-minute film - the video and audio go completely out of sync no matter what format I export it to. There are not a lot of clips used. I'm now trying the method to detach the audio files from the video, hopefully it works.
    These issues are bothering me, in addition to a failed firmware update on Mac OSX 10.7.2 a few weeks ago. I couldn't open my computer and I had to go to the Genius Bar to have them help me backup my files on my computer and reinstall the whole system again. Anyways, any help to the above iMovie issues are greatly appreciated. Just wish that Apple will address these current issues and not just focus on improving their products with awesome features ._.

    Hello,
    Thanks for the reply, I am using embed code generated with Flash Media Playback, as follows:
    <object width="640" height="480"> <param name="movie" value="http://fpdownload.adobe.com/strobe/FlashMediaPlayback.swf"></param><param name="flashvars" value="src=rtmpt%3A%2F%2F50.62.40.55%3A1935%2Flive%2Fchristmastime&poster=http%3A%2F%2Fsq uarestream.ca%2Fpics%2Fframe.jpg&autoPlay=true&streamType=live&optimizeInitialIndex=false" ></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://fpdownload.adobe.com/strobe/FlashMediaPlayback.swf" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="640" height="480" flashvars="src=rtmpt%3A%2F%2F50.62.40.55%3A1935%2Flive%2Fchristmastime&poster=http%3A%2F% 2Fsquarestream.ca%2Fpics%2Fframe.jpg&autoPlay=true&streamType=live&optimizeInitialIndex=fa lse"></embed></object>

  • Any GPS/NAVI apps with video out feature??

    Are there any GPS navigation apps out there for the iPhone that will work with the video out? My car stereo has an audio/video input, I have the a/v connector and I'd love to run a GPS app for navigation and display the NAVI video and audio on my head units audio input. I know that some dont support the video output feature, know of any that do?

    I just tested it on my Nokia N8 (Running Symbian Anna ) and Nokia Beta Labs latest version of the Camera application.
    I have set so capturing geolocation information is saved for video. 
    I Record a video and as you say if you playback the video right away Choose Options -> Details  I get the GPS location shown.
    I  then go to Meny -> Photos
    Choose the Check button (bottom left)
    Then select the Video, then go to Options -> Details
    I also get the GPS coords under Location here. 
    This location data is not shown if you show details under Meny -> Videos though..

  • Imaq RT Video Out using PXIe-8135

    Hi all,
    I am planning to get a PXIe-8135 RT controller and have a requirement to display the image out via the DP port. My questions are:
    1. The IMAQ RT Video Out does support PXIe-8135, doesn't it? My concern is because the controller doesn't have VGA or DVI but DP (DisplayPort). Will it work the same?
    2. PXIe-8135 has two DP's. Assuming the answer to Q1 above is positive, can I display two different images to both of the DP's?
    Please advice.

    Hi Shazlan,
    1- Yes PXIe-8135 RT controller do support IMAQRT Video Out function.
    2- I'm not sure if it's possible since the 2nd DP is just an extended display of the 1st DP
    Regards,
    Laila
    Applications Engineer | National Instruments
    Singapore (65) 6226 5886 | Malaysia (60) 3 7948 2000 | Thailand (66) 2 298 4800
    Philippines (63) 2 659 1722 | Vietnam (84) 8 3911 3150 | Indonesia (62) 21 2924 1911

  • 17" iMac G4 no video out

    Hey there all,
    I bought an old iMac G4 800MHz to use for iTunes playback at my church and it does a great job at that and it can get song titles because it also has an Airport card(802.11b). I'd also like to send video out from it but, the video out doesn't send. I've tried a VGA>VGA adapter and a VGA>Video adapter but neither works and the adapters are good. Any clues or assistance would be appreciated. If I can't get it to work(reasonably priced repair) it's still good for the reason it was purchased.
    *iMac Specs*
    *17" iMac G4 Mac OSX 10.4/800MHz/256MB RAM/40GB HDD/Airport(802.11b)*
    Thanks in Advance.
    Message was edited by: Donna Jones1

    Depending on which Apple mini-VGA to VGA display adapter you have,
    one of them may work while others may not. The model M8639G/A or
    one like it (has different number on original packaging) should work in
    applications with iBook G4, eMac G4, PowerBook (some), and iMac G4.
    • *It should work*, if you follow these simple rules: {avoid static charges when handling connector)
    1) shut down your computer completely before connecting the adapter; sleep-mode won't do.
    2) power up the external screen or video projector after connecting the cable and before booting the Mac.
    3) shut everything down before disconnecting the mini-vga adapter.
    The part number (on my package) says 603-0607; these fit snug in the
    video-out mirror port on an iMac G4. The external display, if supported,
    should appear in the Displays system preference panel, where it may
    be selected and accessed by the computer. There may be other similar
    products that look a lot alike, and may not work in certain computers.
    I have the same model as this, and it works with a mid-2005 iBook G4
    as well as a last series model iMac G4 1.25GHz 17" USB2.0.
    Examples:
    http://store.apple.com/us/product/M8639G/A - or -
    http://www.amazon.com/Apple-Mini-VGA-display-PowerBook-603-0607/dp/B002PXV0S6
    The web page images are helpful to show enlarged view of mini-VGA adapter ends.
    There are other similar adapters which may fit, but don't have correct connectors.
    Not sure of technical differences in those very similar in appearance.
    The adapters may be able to work on any older G4/G5 within standard mini-VGA limits;
    and the old http://store.apple.com/us/product/M9109G/A adapter should also work, too.
    However, the audio portion of this adapter may not work with the iMac G4; so another
    cable setup could be used to provide audio from the headphone jack & other connectors.
    (The similar adapter for use with early Intel-based MacBook has different wiring.)
    What computer model did the adapter(s) you have, come with? What external video
    display unit are you trying to use the adapter and iMac G4 with? There is a possibility
    the adapter and/or the display aren't compatible with the iMac G4; or the video-out
    port is damaged. However, testing the mini-video out port would require known good
    adapters of the correct type.
    Does the System Profiler, and also the System Preferences> Displays show an
    attached external display when the connections are firmly made? One or both
    should give some clue if there is some kind of connection; unless the port is bad
    or the adapter is incorrect.
    Are you going to be using a display or a projector with this? Some products may
    require a different input signal frequency than these older computers generate.
    Not sure on how else to check or troubleshoot the situation if the peripherals
    do match up correctly, and nothing happens. However if an external display
    does work but won't appear correctly, there is a third party app freeware able
    to help adjust resolution and other settings. At least in OS X: SwitchRes X:
    http://www.madrau.com/SRXv3/html/SRX/About.html
    Hopefully some of this helps; at least to confirm the adapter details, and the
    basic attachment process usually involved. The System Profiler should have
    an indication of a correct connection; if the port or adapter is wrong/broken,
    then this would not be a pointer to gauge success. Except by its absence...
    For other methods of troubleshooting video, should the machine have an
    issue and you need to use an external mirror display to access it, see this:
    http://discussions.apple.com/thread.jspa?threadID=914904
    Good luck & happy computing!
    +{ edited }+

Maybe you are looking for