Appropriate Steps To change the weblogic password in Cluster ENV

Hi Experts,
We need to change the password for weblogic(10.3.3) as activity. It would be helpful , if you can provide us , what would be the best ways to change it and what sequence we should follow for changing the password and then Bouncing
Two Physical Servers.
Server One : Admin Server and Managed Server
Server Two : Managed Server Only
Regards
Sourabh Gupta

Hi Kalyan,
We do this steps when we forget the weblogic password. My Question is on sequence.
But We did :
Change Weblogic Password from Security Realm and then edit the boot.properties. Bounce the Admin Server.
Then Change the Password for Managed Server ( from the front end ) and bounce the managed server.
Navigation : Console--> Environment--> Servers--> (OIM server name)--> Configuration--> Server Start.
If we have clustered env , How should Be folllow ? Should be do the same steps as mentioned above on both the nodes or through one Server is suffice.
One thing I want to tell you , once we did the steps as mentioned by you , you may be in trouble. Because Have same issue earlier where we forget the weblogic password and change like the way you said , What happened after that our deployments are getting failed , Because Our deployment using INternal User ( related to OIM) get missing . My understanding is weblogic stores all the users in ldift file , once we replace it all users may be removed ( Not Sure though) .
Please pass you suggestion
Regards
Sourabh Gupta

Similar Messages

I am receiving a message that my ID has been disabled, and I followed the steps to change the password, but still receive the same message. Cannot access app store or do updates.

I am receiving a message that my ID has been disabled, and I followed the steps to change the password, but still receive the same message. Cannot access app store or do updates.

In what way are you receiving this message? It is very common to get an email telling you that your ID has been disabled, and asking you to confirm all your details so the sender can steal your identity online.....

Create Dynpro to change the UME password

Hi experts,
I need to create a webdynpro with the following steps:
- View to login (two textinput with one button, the first textinput to put the username, the second textinput to put the pass, and the button to execute the login ). (This part it's clear)
The problem is in this part:
- The next view is to change the actual password, I will have three textinput ( first to put the actual password and the others to put the new password), the problem is I don't have idea how to do to it
Any idea?
Thanks in advance,
Jose Manuel

Hi,
With your code I had a mutable exception, I've solve the problem with this code
try{
IUserFactory userfact = UMFactory.getUserFactory();
//get user id of the user to change the password
String userId = wdContext.currentLicenceUsersOutputVNElement().getUserid();
//get user object
IUser specifiedUser = userfact.getUserByLogonID(userId);
//get user maintance object
IUserMaint userMaint = userfact.getMutableUser(specifiedUser.getUniqueID());
//get user account
IUserAccount uacc = UMFactory.getUserAccountFactory().getUserAccountByLogonId(userId);
//create mutable user account
IUserAccount iuacc = UMFactory.getUserAccountFactory().getMutableUserAccount(uacc.getUniqueID());
iuacc.setPassword(wdContext.currentContextElement().getNewPassword());
iuacc.save();
iuacc.commit();
manager.reportSuccess("Password has been reset.");
catch (Exception e)
manager.reportException("error occured " + e , false);
e.printStackTrace();
thanks for you colaboration

HT201356 Can you please put the steps to change the rescuer email address since I cannot receive any emails

Can you please put the steps to change the rescuer email address since I cannot receive any emails

The steps on the page that you posted from should work, but you can only change your rescue email address if you remember your answers to your security questions :
- log into the account via the 'manage your apple id' button on http://appleid.apple.com
- select the Password & Security section on the left-hand side of your account's screen
- answer the account's security questions
- you will then get a screen where you can change the address (and/or the questions)
If you can't remember your answers, and you aren't receiving the reset email to your current rescue email account (and you've checked the spam folder as well as the inbox on it, and tried clicking the reset link again) then you will have to contact Support in your country to get the questions reset.
Contacting Apple about account security : Contact Apple for help with Apple ID account security
If your country isn't on that page then try this form to contact Support : https://www.apple.com/emea/support/itunes/contact.html
When they've been reset follow the above steps for changing your rescue email address

How to change the Default Password on AP1131AG

Hi all :
I tried to change the default password Cisco to other by command line but the password cannot work out.
The command line I used are as below :
AP#conf t
Enter configuration commands, one per line. End with CNTL/Z.
AP(config)#enable pass
AP(config)#enable password 4dMINO123 ?
LINE    <cr>
AP(config)#enable password 4dMINO123
AP(config)#exit
AP#wr
*Mar 1 04:39:23.902: %SYS-5-CONFIG_I: Configured from console by console
Building configuration...
[OK]
AP#exit
This still cannot cahnge. Below I do again below commands :
AP(config)#enable secret
% Incomplete command.
AP(config)#enable secret ?
0      Specifies an UNENCRYPTED password will follow
5      Specifies an ENCRYPTED secret will follow
LINE   The UNENCRYPTED (cleartext) 'enable' secret
level Set exec level password
AP(config)#enable secret 5
% Incomplete command.
AP(config)#enable secret 5 ?
LINE The ENCRYPTED 'enable' secret string
AP(config)#enable secret 5 LINE
ERROR: The secret you entered is not a valid encrypted secret.
To enter an UNENCRYPTED secret, do not specify type 5 encryption.
When you properly enter an UNENCRYPTED secret, it will be encrypted.
AP(config)#enable secret LINE
AP(config)#exit
AP#
*Mar 1 04:40:53.021: %SYS-5-CONFIG_I: Configured from console by console
AP#
AP#exit
After that when I access with >en again as below with correct password of 4dMINO123 and it always fails as below :
Can anybody help to provide correct way of changing the default password of Cisco to another password? Many thanks!
AP con0 is now available
Press RETURN to get started.
AP>en
Password:
Password:
Password:
% Bad secrets
AP>en 0
AP>en 5
% No password set
AP>en 15
Password:
Password:
% Password: timeout expired!
Password:
% Bad secrets
AP>
AP>
AP>en
Password:
Password:
Password:
% Bad secrets
thanks and best regards,
tangsuan

Hi, I have even the worst problem,
that seems probably to to be never asked on Internet. After quick learning how to reset this creapy device, I can't get by no means the enable password in default config for this box, having read everywhere from Cisco guide through community pages to Google pages.. NOWHERE.
Question is : what else except Cisco, cisco, root, password... can solve this stupid issue?!? I expect some guru from responsible AP BU to answer this with definite answer, or someone from Cisco having mercy with me to contact such guy(s).
Here is my desperate situation :
Nothing from this page helped :
http://www.cisco.com/en/US/partner/products/hw/wireless/ps430/products_password_recovery09186a00800949d0.shtml#reset_ap_newer
Situation after hard reset:
Xmodem file system is available.
flashfs[0]: 26 files, 8 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 6879232
flashfs[0]: Bytes available: 9119744
flashfs[0]: flashfs fsck took 43 seconds.
Base ethernet MAC Address: 00:22:55:9f:fc:a0
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
button pressed for 1 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
Loading "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"...#########################################################################################################################################################################
File "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:38 by alnguyen
Image text-base: 0x00003000, data-base: 0x0035E440
Initializing flashfs...
flashfs[1]: 26 files, 8 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 6879232
flashfs[1]: Bytes available: 9119744
flashfs[1]: flashfs fsck took 6 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-LAP1131AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ1238Q0HK
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:22:55:9F:FC:A0
Part Number                          : 73-8962-14
PCA Assembly Number                  : 800-24818-13
PCA Revision Number                  : A0
PCB Serial Number                    : FOC12354426
Top Assembly Part Number             : 800-29144-03
Top Assembly Serial Number           : FCZ1238Q0HK
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131AG-E-K9
Press RETURN to get started!
*Mar 1 00:00:08.354: %CDP_PD-4-POWER_OK: Full power - AC_ADAPDOWN: Line protocol on Interface FastEthernet0, changed state to up
Press>en
Password:
Password:
Password:
*Mar 1 00:00:27.393: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
% Bad secrets
Press>en
Password:
Password:
Password:
% Bad secrets
Press>
*Mar 1 00:00:36.530: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 192.168.1.2, mask 255.255.255.0, hostname Press
Press>en
Password:
Password:
Press>sho ver
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:38 by alnguyen
ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
Press uptime is 17 minutes
System returned to ROM by power-on
System image file is "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"
cisco AIR-LAP1131AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ1238Q0HK
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:22:55:9F:FC:A0
Part Number                          : 73-8962-14
PCA Assembly Number                  : 800-24818-13
PCA Revision Number                  : A0
PCB Serial Number                    : FOC12354426
Top Assembly Part Number             : 800-29144-03
Top Assembly Serial Number           : FCZ1238Q0HK
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131AG-E-K9
Configuration register is 0xF
Press>

How to change the default password file's name and path when the database created?

how to change the default password file's name and path when the database created?
null

Usage: orapwd file=<fname> password=<password> entries=<users>
where
file - name of password file (mand),
password - password for SYS and INTERNAL (mand),
entries - maximum number of distinct DBA and OPERs (opt),
There are no spaces around the equal-to (=) character.

HOw do you change the Apple Password ro several Apple devices wit the same user name?

I am trying to change the Apple password for four Apple devices, including an iPhone, iPad, iMac Air, and Desktop MAC. The iPhone password is corrupted so it is interfering with the synching of the four devices on the iCloud. I want to reset the password for all four devices and get them so they will synch with each other as well as the iCloud.

Hi Stew,
App Store requires 10.6.8, is the 10.5.5 you kist correct?
Antway, to change ID...
http://support.apple.com/kb/ht5621

Is there a way to change the VNC password thru unix command in ARD2?

In a local network, I get access denied errors from macs that have the vnc password different than the Administrative login user password. I needed to change the Admistrator password which I did thru the Unix command in ARD2.
Now.
Is there a way to change the VNC password thru unix command in ARD2?
Example:
remote computer setup
Panther 10.3.9
vnc password - gopher
user ID - testARD with admin rights
user password - backdoor
ARD2 Computer setup
10.4.10
login ID - testARD
password - backdoor
I get the blue icon but get an 'access denied' error.
I change the password from backdoor to gopher.
I get the red with dash icon but, can get access to the computer.
What is going on? Is ARD2 using the VNC resource instead of ARDs resources?

A quick search of Google finds this <http://www.macgeekery.com/tips/cli/settingremote_desktops_vnc_password_interminal>. I have not tested this myself.
bill

Error while trying to change the user password on OSX Lion

Hello,
I am trying to change the user password ( no admin user ) using the webinterface. I enabled the functionality in webservices on the server.
I can loginto the three line password changing form. After I enter the old and two times the new password, I get the information
"Your request could not be completed. The password server may be unavailable."
How can I fix this problem? I also tried https://discussions.apple.com/thread/2485167?start=0&tstart=0.
Thanks in advance for help.

I currently have this error on my 10.6.8 ML server when trying to change password.
In my situation, the message definitely comes from the password policies. As soon as I use a new password that respects minimum complexity (e.g. 8 characters min, 1 lowercase letter, 1 uppercase letter, 1 number), the password changes flawlessly.
It would be nice to change this horrible message to something more meaningful... If someone has any ideas on how to do this, thanks for sharing!

How to change the Portal Password using a link from Web dynpro application

Hello Everybody,
I have a requirement to change the user password from a web dynpro application which is available on a mobile device. Firstly User will log into the portal through a mobile device and after getting authenticated user will be redirected to the mobile application. Within this mobile application there will be a link to change the login password(Portal login). Can somebody tell me how can i change the portal login password from a link available within the mobile application. Looking forward for a suitable reply.
Thanks to all,
Regards,
Saby.

Hi Maksim,
Thanks for your reply..but i would also like to know can we directly use the Change Password Iview "persoUserPassword" from the portal. Can i directly Pass the URL of this iview from the portal to a "Change Password" link in the web dynpro application, so that when the user click this link he should be able to see this Iview on his/her mobile device and should be able to change the password from there. But i dont know whether this iview will appear properly on the mobile device or we have to have a custom web dynpro application for this purpose...Please reply with a suitable answer.
Thanks in advance.
Regards,
Sarabjeet Singh.

How to find out who has changed the SYSADMIN password?

Hi,
Is there a way to trace who has changed the SYSADMIN password in an instance?
Regards,
Neeraj

of course, this is limited to any updates to the
user, e.g. added responsibility, etc. So, it
probably is very limited in value.That's why it is recommended to enable AuditTrail, which is a way of keeping track of changes made to important data in Oracle Application tables. AuditTrail keeps a history of the following three questions:
1. What changed
2. Who changed it
3. When did the change take place

How do I change the admin password in SJSWS 7.0?

I've googled this, searched the forums, read the manual, but I haven't found anything that explained how to change the admin password for SJSWS 7.0. So, right now I'm stuck with "adminadmin" as the password, which I think is the default since I don't remember specifying that during install. Clearly I can't use this in production with the default admin password... sorry if this is a rtfm question, but I really didn't see anything in the manual about changing the admin password. Thanks!

You could use the following CLI command:-
wadm> set-admin-prop --set-password
More information about the command:-
http://docs.sun.com/app/docs/doc/819-3283/set-admin-prop-1?a=view
You could also use Administration console-
- Login to the Administration Console and click on the Nodes tab
- In the Nodes page, click on the Administration Server link within the Nodes table
- Go to "Administration Server Preferences" section in the General page and change the password

After change to Mavericks my Mac become too slow e I can't use it because stays asking passwords for "talagent" and "messages agent" as icloud keys. I got changed the icloud password many times and still doesn't work. I can't open any program.

After change to Mavericks my Mac become too slow e I can't use it because stays asking passwords for "talagent" and "messages agent" as icloud keys. I got changed the icloud password many times and still doesn't work. I can't open any program.

Back up all data.
Launch the Keychain Access application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Keychain Access in the icon grid.
Select the login keychain from the list on the left side of the Keychain Access window. If your default keychain has a different name, select that.
If the lock icon in the top left corner of the window shows that the keychain is locked, click to unlock it. You'll be prompted for the keychain password, which is the same as your login password, unless you've changed it.
Right-click or control-click the login entry in the list. From the menu that pops up, select Change Settings for Keychain "login". In the sheet that opens, uncheck both boxes, if not already unchecked.
From the menu bar, select
Keychain Access ▹ Preferences ▹ First Aid
If the box marked Keep login keychain unlocked is not checked, check it.
Select
Keychain Access ▹ Keychain First Aid
from the menu bar and repair the keychain. Quit Keychain Access.

How to change the sysadmin password for maintenance wizard if you have forg

How to change the sysadmin password for maintenance wizard if you have forgotten the password and can't log in.

Log into SQL*Plus as the $EOFUSER and do:
update eof_user set password = 'passwd_you_want' where user_id = 0;
commit;
-Vikki
Product and Development Manager for Maintenance Wizard

Facing an error when change the sysadmin password

hi expert,
when i am going to change the sysadmin password i m facing the below error on linux in production environment. i cant understand why this error occured. i change the sysadmin password many times but never get any error. when going to change the sysadmin password the production instance is open.
[applprod@oracleerp ~]$ FNDCPASS apps/apps 0 Y system/manager USER SYSADMIN sys@adm!n
-bash: !n: event not found
plz suggest how can i resolve the above error.
thanks & regards
pritesh ranjan

Hi Pritesh Ranjan,
plz suggest me one thing can i change sys password directly without down the ebs application same as system user.
exp -
alter user system identified by manager;
for sys
alter user sys identified by oracle123; (in production environment without down the ebs application)
Yes, you can change without restarting the ebs application.
And your syntax seems fine.
Thanks &
Best Regards,

Appropriate Steps To change the weblogic password in Cluster ENV

Similar Messages

Maybe you are looking for