Apps in SD lost when USB memory is connected

D6633. Lollipop, 128gb SD, when I connect 32gb to USB port, all apps moved to SD memory is "lost". Ejecting USB does not help. Only after reboot does apps in SD work again.

Have you searched the forum for similar issues?
https://talk.sonymobile.com/t5/Xperia-Z2/Xperia-z2-otg-and-micro-sd-issue/m-p/975049#M27003
All we have to decide is what to do with the time that is given to us - J.R.R. Tolkien

Similar Messages

OS X kernel logs problem when USB flash drive connected.

Previously, my Creative Nomad Muvo TX (MP3 player/1GB USB memory stick) worked fine with my Intel Mac mini (10.4.8) until the latest EFI 1.1 update.
Now the USB drive does not mount or appear in finder. It is visible in the System Profiler in the USB section, but the disk utility does not see it.
While the USB stick is plugged in, the system logs the following line repeatedly:
Nov 26 21:32:39 kernel[0]: USBF: 2517.425 AppleUSBEHCI[0x3969000]::Found a transaction past the completion deadline on bus 253, timing out!
Booting in Windows XP (with bootcamp) and plugging in the USB memory stick works fine. So the USB stick and the Mac mini hardware is functioning.
Other USB 2 external harddrives are functioning properly in OS X.
I suspect that the latest Mac OS X or EFI 1.1 firmware update has spoilt my previously happy USB memory stick connection.
Any suggestions?
Thanks in adcvance.
Stephanus

Hi, Stephanus.
1. If Creative does not support that device with a Mac, then that should tell you something. Even if it worked in the past, since they don't support it, there's no guarantee that changes to Mac OS X would render it unusable as you've noted. With that kind of attitude from Creative, I'd think about switching to an iPod...
Since you can use it when booted into Windows with Boot Camp, you might want to consider running Parallels Desktop for Mac. This leverages the virtualization technology of the Intel chips, permitting you to run Mac OS X and Windows simultaneously, rather than having to boot into Windows with Boot Camp. Parallels is cheaper than buying an iPod.
2. The USB message you reported is essentially indicating that the OS detected a USB device but cannot talk to it. This is unlikely to be something you're going to work around, e.g. with Terminal.
3. If you want to pursue this further, you can:3.1. Install the USB debug kit for your version of Mac OS X. Apple provides a variety of Mac OS X USB Software Debug Versions that "are used to provide information about USB device and interface detection, driver and interface matching, driver loading and information generated as a result of normal and abnormal conditions." You could install the package corresponding to the version of Mac OS X you are running and this may help identify if the issue is a USB problem and the exact USB anomaly causing such.
3.2. Take what you've been able to lear from the USB debugger and do one or more of the following:• Join the Apple USB Mailing List. Once your registration is approved, submit a question including the enhanced output from the USB logger and requesting additional advice. That list is monitored by developers of USB devices. Posts are sometimes answered by Apple engineers.
• Join the Apple Developer Connection at the "free" level, then submit a bug report.
• Submit a Mac OS X Feedback.If Creative has their own forums, ala Discussions, you might also want to search or post there for similar reports.Unfortunately, that's about all I have to offer at this point: I don't have the Creative device and hence can't test it.
I think that Creative is disinterested in helping you is a key issue you need to consider.
Good luck!
Dr. Smoke
Author: Troubleshooting Mac® OS X

During setup HP PSC 2175v printer locks up XP computer when usb cable is connected.

During setup HP PSC 2175v all-in-one printer locks up XP computer when usb cable is connected. Only hard shutdown and restart to get computer working again works. How do you fix this issue?

The USB port on the PSC2175V may be defective or the XP USB port is defective.
Can you try the PSC2175V on another computer?
Check the XP device manager for any problems, do other USB devices work ok?
Please mark the post that solves your issue as "Accept as Solution".
If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
I am not a HP employee.

RMBP 15" 2013 won't connect to wifi when USB or Thunderbolt connected

Has anyone else noticed any issues connecting to wifi when they have a device plugged in to the USB or Thunderbolt ports? Mostly happens when turning on or waking from sleep. As soon as I removed the connected devices it connects to the wifi instantly! This has happened when I've had my Apple monitor connected via the Thunderbolt port and on a seperate occasion when my iPhone was connected to the USB.
Tis werid!
I'm running Mavericks OSX 10.9.2 on a 2013 15" rMBP :-/

Go to System Preferences > Network > Click the Cog Wheel > Set Service Order > Drag Airport to the top.

Network Configuration Window Freezes When USB NDIS Internet Connection Sharing and Ethernet Port Are Used Simultaneously

Current Setup:
Asrock Extreme 4 Z77 mobo with built-in Broadcom NetLink (TM) Gigabit Ethernet. Windows 8 Pro. Intel i5-3570k (using onboard Intel 4000 HD Graphics). RAID0- 2 OCZ Vertex 4's.
I will refer to this setup as my tower.
The Ethernet port works fine by itself. When I use wired tethering with my Android phone (Droid 4 running on 4.0.4 Ice Cream Sandwich), it works fine when nothing is connected into the Ethernet port in the mobo.
The issue arises when I try to connect both simultaneously. The network configuration window in windows basically freezes and I cannot really navigate it without a ~60 second delay at best.
I would like to be able to accept the internet from my Android via a USB tether and either bridge the connection or use the internet connection sharing service to route traffic through the unused Ethernet port on the mobo (either to another computer/xbox
or more desirably a switch/router to spread to the entire home network). I have extensively researched the issue of Windows 8 become slow and unresponsive when I attempt to do this and I have not found anyone with the exact problem. I am able to
do both the MAC bridge miniport (bridge 2 connections) and Internet Connection Sharing though a Windows Vista (home premium) Laptop I have. The difference between the laptop and the tower I am try to do this on is the laptop has a WIFI and Ethernet connection
while the tower only has the on-board Ethernet.
Do I have all the necessary equipment to accomplish this, or do I need to buy a PCIe WIFI card? If so could I get away with just getting a USB WIFI dongle?
Any help would be very appreciated.

I had the same problem and came here by searching.
Per Rosengren's method solved the problem, but he didn't say how to do it, so I'll try to explain step-by-step for anyone that may venture here.
Open Device Manager (right click on Computer > Manage > on the left side, under System Tools choose Device Manager)
Choose the problematic device in Network Adapters (for me it's called HTC Remote NDIS based device)
Right click on it and choose Update Driver Software...
Click Browse my computer for driver software
Click Let me pick from a list of device drivers
Uncheck the box Show compatible hardware
For the manufacturer, choose Microsoft Corporation
Now you will have two options:
- Remote NDIS based Internet Sharing Device
- Remote NDIS Compatible Device
I chose the second one and it solved the problem, but if it doesn't work you could try the other one. In my case, the driver that was being used was neither of these, but a special driver from Android SDK ADT bundle.
Pick one and click Next. If a dialog comes up, confirm by clicking Yes.
Wait a few seconds for the connection to restart. If it doesn't work, try disabling and reenabling USB tethering on the phone, or reconnect the USB cable.
I should also note that I'm using a custom Android ROM on HTC Wildfire S (unofficial Cyanogenmod). If you have a stock ROM with HTC Sense, maybe this method may not work and you'll need a proprietary HTC driver.

OS X crashing on reboot when USB Bluetooth device connected

After a very recent SW update to 10.4.5 OS X is crashing on reboot with a black screen of death when USB Bluetooth D-Link DWB-120M is connected. Crash is systematic if bluetooth device is connected. How do I correct the situation to be able to make use of the bluetooth USB device?
[email protected]

Hi, noordm. Welcome to the Discussions.
You wrote: "...crashing on reboot with a black screen of death..."Can you clarify what you mean by "black screen of death?"
For example, if you are seeing this message, that indicates a kernel panic.
If so, see my "Resolving Kernel Panics" FAQ. This FAQ includes step-by-step instructions for identifying and resolving some of the most common causes of kernel panics. The FAQ is a roadmap: start at the beginning and work systematically through the end, i.e. the "If all else fails..." section.
Good luck!
Dr. Smoke
Author: Troubleshooting Mac® OS X
Note: The information provided in the link(s) above is freely available. However, because I own The X Lab™, a commercial Web site to which some of these links point, the Apple Discussions Terms of Use require I include the following disclosure statement with this post:
I may receive some form of compensation, financial or otherwise, from my recommendation or link.

When USB hub is connected Sat P30 doesnt boot up

I recently purchased a Toshiba P30, in the USB port I connected an USB 2.0 HUB.
This to connect, printer, scanner, external harddisk etc., etc.
When the USB HUB is pluged in the USB port, the computer will not start up.
I must first disconnect the Hub before I can push the on/off button.
Can somebody help me and tell me what I must do to be able to start the computer
with the USB HUB attached to the notebook.
Manny thanks
Jos

Hello Jos
It is really not easy to say what the problem can be but in my opinion it is definitely because of HUB. You will not believe me but my colleague has Satellite P10 and two USB HUBs are connected to his unit and there is no problem at all. I dont know which one you have but if there is any possibility try to test it with other one.
Bye

Can I retrieve a paid app that was lost when I restored my iPad?

The iPad was not available in my hometown, but lucked out and one was in stock out of state while traveling. I bought it and had it activated in the store so I could download apps and play on the 4 hour ride home. Problem was that now my iTunes would not recognize my iPad so I could not put any of my music on it. I restored my iPad and in doing so lost my paid app! Is there anyway to retrieve it? I have the email receipt that I purchased it, but for the life of me can't figure out how to get it back with out repurchasing it. I appreciate any suggestions.

osKco wrote:
I have not tried to repurchase it since it does not say installed when I look it up
Because it is not installed on your iPad.
If you are signed inot ht eiTunes store wioth the same account used to purcahse that app, click on Buy and it will tell you that you have already purcahsed it and ask if you want to redownload it.

Has anyone got a good program / app that will backup my USB memory stick to my Mac?

As above , would appreciate any suggestions, as currently have a lot of work on my memory stick which is so important and thought I had lost it today!! If every time I plug my flash drive in, it would back up onto my Mac that would be great
Thanks
Amfox1

Try Copy From the stick and Paste To the Mac hard drive.
Or use Disk Utility to create a image of the info on that stick saving it to the internal hard drive of the Mac.

All sound lost when usb microphone was installed

Hi all
I installed a usb mic to narrate over some tracks and clicked on the mic button in the audio window and subsequently adobe will not play any sound whatsoever. The original tracks play the sound in Microsft media player (though I also tried windows movie maker and no sound there either) so am completely flumoxed.
Can anyone help or have any suggestions please.
Cheers
Jools

Jools,
Welcome to the forum.
Did you install any drivers with the USB mic? If so, chances are that these smurfed something in your Audio Hardware settings in PrPro. Look especially at your ASIO settings now. My guess is that you will have some additional choices in the drop-downs.
Now, USB mics are prone to problems in most Adobe software. Some function OK, but others just do not.
One thing to try, would be to download and install ASIO4ALL. It's free and has fixed so many ASIO problems for others. You will have to point PrPro to use it in all the drop-down boxes. After you install it, reboot, and it will appear as a selection. Many on the Audition have used it to allow for the use of USB mics and a ton of other esoteric equipment.
Good luck,
Hunt

Why doesn't Wi-Fi turn OFF when USB Ethernet is connected?

When I get into the office, I connect my MacBook Air (2011/Lion) via USB Ethernet (we have Wi-Fi too).
When connected through USB Ethernet, my Wi-Fi stays connected as well.
Is it possible to have Wi-Fi turn off automatically when connected via USB Ethernet?

You can configure your Network System Preferences so that your Ethernet interface has preference over wifi. It will not automatically turn off wifi, but it will use the Ethernet if it's plugged in.

2960x broken when USB console cable connected

Hi
I have a strage issue here, on 2 different 2960X ( WS-C2960X-48TD-L ) when I connect the mini USB cable for console access the switch do not respond anymore, after few seconds all the led stop to flash, the switch start to broadcast all packets on all ports, causing redundand port to create a loop.
The issue is present on both switches, tried to cold boot, tried updating to 15.0(2)EX4 but still same issue.
I tried different usb cables that are working on 2960S and 3750x, anyone with this issue ?
It is annoing as I have only usb pors available there.
The issue start when the cable is plugged in without even start the login, the Control plane free about 20-30 seconds after. If I remove the usb cable everithing is fine again, but spanning tree on other switches has gone crazy due to the switch was farwarding on all ports.

Hi,
anyone has this same issue ?

My macbook pro says connection lost when I try to connect to my wifi.

I cannot connect to my wifi at home via wireless. It only works if I'm connected via ethernet cable. When I would attempt to connect to my wifi, it says connection lost. Does anybody have a solution? (not sure if this is helpful or not, but is says no network selected)

I cannot connect to my wifi at home via wireless. It only works if I'm connected via ethernet cable. When I would attempt to connect to my wifi, it says connection lost. Does anybody have a solution? (not sure if this is helpful or not, but is says no network selected)

Mac Mini sluggish when USB external drives connected

I'm not sure what's causing this issue, but I have a Late 2012 Mac Mini and when I plug in a USB 3.0 thumb drive or my WD My Book Studio (also USB 3.0), the mouse cursor is very sluggish and laggy. I will physically move around my mouse and the cursor is extremely slow to reflect such movements on the screen. It did it with an empty USB flash drive, so there's no indexing or anything else going on in the background. Ejecting the drive will not solve this issue until I physically remove the drive from the USB port. What's causing this and how do I fix it?

format the drives for MAC OSX extended journeled.....when you do that, is the problem still present?
Ive head of this before on WD drives (cant stand them) because they have some nasty bloat loaded onto them for installing them (no need for that EVER) on your computer.
when you insert the WD drive, does the drive come up AND ANOTHER icon saying something like "WD xxxx" (i recall its something like WD utility, or WD support) ???
Ive got nearly 100 hard drives, but wont own a WD, ....if i get a free one, i destroy anything on it with a erase and wipe with disk utility "format for mac osx extended journaled"
AS FOR YOUR STICK DRIVE,......are you sure its mac compatable??? most stick drives list that in the fine print, and mac owners buy a cheap stick drive that isnt 'kosher' with MAC

Audio Wont Play Through Output When Usb Input is Connected

I have the "MXL Mic Mate" usb mic interface. It works perfectly in GarageBand, once I choose the Output to the Built-in output in preferences.
However in Logic, when the device is recognized, It can record (pick up the input audio) but the no sound can be heard coming from the output.
I tried going under the computers preferences and setting the default audio output but no luck.
Advice on how to fix this would be greatly appreciated.
thank you.

You might need to check the settings in teamspeak.
What happens if you dont use team speak overlay? does the sound play normally from your headphones?
I'm an HP Employee.
The opinions expressed here are my personal opinions, not of HP.
Click on Thumbs up if my post helped you.
Make it easier for other people to find solutions, by marking an answer “Accept as Solution” if it solves your problem.

Apps in SD lost when USB memory is connected

Similar Messages

Maybe you are looking for