Arch install on Imac G5-SOLVED

Trying to install Arch on a G5-Imac.CD boots normally but when trying to start the installer it gives an "Invalid memory access at SRR0 and SRR1 (with big numbers)"
Any idea what is going on here?
ARCHPPC finally running on 64-bit with 32-bit userland
Last edited by mianka (2010-04-09 15:41:22)

It gets the yaboot prompt,as far as I can see the kernel boots (on a white characters on black screen) then the colors invert with following messages:
done
found display etc; etc ...done
copying OF device tree...
building dt strings...
building dt sttructure ...
Device tree strings 0x02fcc000 -> 0x02fcd4e0
Device tree struct 0x02fce000 -> 0x02fd8000
Callind quiesce...
DO-QUIESCE finishedreturning from prom-init
Invalid memory access at %SRR0: 00000000.0140399c %SRR1: 10000000.00083030
ok
0 > _
END OF THE MESSAGE AS SEEN ONSCREEN
At this prompt it is impossible to give any command.
Hope this can help you.
So long.

Similar Messages

After using "migration assistant" from my old iMac to my new iMac, some tools stick while using Photoshop CS 6 Extended. My current operation system is 10.10 Yosemite. I was wondering if UN installing then RE installing CS 6 might solve the problem. If th

After using "migration assistant" from my old iMac to my new iMac, some tools stick while using Photoshop CS 6 Extended. My current operation system is 10.10 Yosemite. I was wondering if UN installing then RE installing CS 6 might solve the problem. If this is recommended, I would need complete instructions on doing this. I have there serial number for the product.

using migration assistant is problematic.
at this point yes, you should uninstall everything migrated, clean and then reinstall properly using the installation files.
cleaner: Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6
installation files:
Downloads available:
Suites and Programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4 | CS3
Acrobat: XI, X | 9,8 | 9 standard
Premiere Elements: 13 |12 | 11, 10 | 9, 8, 7
Photoshop Elements: 13 |12 | 11, 10 | 9,8,7
Lightroom: 5.7| 5 | 4 | 3
Captivate: 8 | 7 | 6 | 5
Contribute: CS5 | CS4, CS3
Download and installation help for Adobe links
Download and installation help for Prodesigntools links are listed on most linked pages. They are critical; especially steps 1, 2 and 3. If you click a link that does not have those steps listed, open a second window using the Lightroom 3 link to see those 'Important Instructions'.
window using the Lightroom 3 link to see those 'Important Instructions'.

[SOLVED]Shift my Arch install to a new (smaller) PC/HDD?

Hey all, I've looked around all sorts of forums for the answer to this, but none of them seem to cater exactly to my need, so I'll post my problem here!
Essentially I bought a new harddive. Well actually, I bought a whole new PC-worth of parts, but it's the harddrive causing problems.
I've had this Arch install for quite a while, and as such it's pretty well tweaked and messed about with, so I REALLY don't want to start again with a clean install, so I want to (For lack of a better terminology) Copy-paste my entire Arch install into the new harddrive.
I looked into Clonezilla, but there's a slight issue... My new drive is smaller than my old one. I know this was a dumb mistake on my part, but really I don't need anything bigger (Even with a load of movies, VM's and Wine games that can easily be deleted I'm only using 60-70GB of drive right now) And the only reason I really needed a new drive was because the new motherboard doesn't have an IDE slot, and my old drive is an IDE (I know there's adaptors for that, but they sound a bit dodgy at best)
My current partitions on my drive are also numbered a bit funny, which I think is where this went wrong when I attempted it, due to me distro-hopping a bit before landing on Arch.
So, is there an easy way to go about this, that I'm overlooking? Are there more config files that I should have editted (All I did upon clonezilla-ing the main partition was change the grub menu.lst file to say sda1 instead of sda3, and the same in fstab)
What I tried first time round, was to use Clonezilla, and only clone my /dev/sda3 partition (That's the one with Arch installed, sda1 is just an empty box that I occasionally store junk in) And this put a partition on the new drive, sda1, which was the reason for editting the menu.lst/fstab.
I then (Upon the above failing to boot) used GParted (Using a Mint LiveCD) To shrink my partitions down so they're approx. 65GB each (My current drive is 200GB, split equally in half, and my new drive is 160gb) Hoping Clonezilla would believe my drive was only 130GB (This still didn't work, it still told me the destination drive's too small)
Is there anything else I can do that I'm missing?
Last edited by Reded (2012-07-15 17:12:58)

Phew, thread is solved!
To R00KIE, your post actually helped me quite a lot - It turns out I was missing installing grub + regenerating initramfs
So how I did it:
GParted the new drive so it had a filesystem
Boot from a Ubuntu LiveCD,
mount both drives
copy-paste drive-to-drive (literally... used the cp command)
chroot into the new drive
adjust fstab/menu.lst
grub-install /dev/sda
mkinitcpo -p linux
reboot
PROFIT!
You're right ROOKIE, that whole process was far simpler than some websites make it out to be Thread closed!

[SOLVED] Advice for Arch install with rEFInd dual boot Lenovo laptop?

I am trying to plan an Arch install on a new laptop for dual boot with Windows 8.1, but I know there is a potential to cause huge problems so I have been trying to read and learn about the hard disk partition structure and how I might install the rEFInd boot files so that I am still able to boot Windows once Arch is installed. (Unfortunately for some tasks such as updating the maps on my satnav box Windows is essential). However I am really quite unsure if I am doing the right thing in the way I am thinking about the Arch install so I would appreciate any help from experts on the forum.
The laptop is a Lenovo IdeaPad Y510p which came with Windows 8 pre-installed, with the option to upgrade to Windows 8.1. The upgrade was completed without issue and I then looked into the question of hard drive partitions and boot. I had read posts on the Ubuntu forums about users who had installed Ubuntu on this same laptop and ended up being unable to boot Windows afterwards so I wanted to tread very carefully before executing anything which might cause really major damage. I had also read on the Lenovo forums replies about people who had replaced the hard drive and installed linux only to find that they could not boot to the recovery partitions, with replies from Lenovo moderators saying that if the partition structure had been changed then the laptop would have to be sent back to Lenovo for a factory repair.
On this laptop to get into the bios or boot options you do not just press the power button and hit an F key, but instead there is a special small "OneKey Recovery" button next to the power jack, which opens up with options for BIOS setup and boot options as well as normal boot or recovery. This OneKey Recovery button is therefore needed to boot a usbkey - the power button only allows it to boot to windows presumably until/unless a different bootloader and NVRAM entry is amended.
I have done all the initial ( safe!)changes necessary to move to the point at which I can execute the Arch install. From within Windows (switched off fastboot, and shrunk the "C:" drive to make space for linux partitions). I have also switched off Secure Boot from the BIOS, and made sure that Windows still boots up fine.
The current arch install iso (February 2014) boots under uefi just fine - and of course once booted I have access to the gdisk programme. That certainly showed the pre-existing partitions on the drive (8 partitions with partition number 2 being the EFI partition, and three recovery partitions!) with a GPT partition table, and it should therefore be possible to make the necessary new linux partitions in the now unallocated space on the disk that was freed up with the internal disk management facility within Windows 8.1. So at that point I created three partitions for a root partition (type 8300), a swap partition (type 8200) and another type 8300 partition which will become /opt in the installed Arch system.
In order to try and not make any changes to the partition structure I let the three new linux partitions be number 9, 10 and 11.
I am told that for a GPT disk it is a definite no-no to try to create more than one EFI partition. So I will need to use the existing EFI partition to place the rEFInd files and the kernel once I install Arch.
In this (Y510p) laptop the EFI partition contains the following structure:
BOOT/ - containing only boot.sdi
BOOTSECT.BAK
EFI/ which contains two directories Boot/ and Microsoft/
so EFI/Boot/ contains only Boot64.efi which is likely a fallback copy of the Windows 8.1 bootloader
and EFI/Microsoft/ contains a Boot/ directory - so
EFI/Microsoft/Boot/ contains loads of language specific directories like en-GB/
plus bootmgfw.efi (which I believe is the Windows main efi loader file)
bootmgr.efi
memtest.efi
The scheme that I am planning to use which I have previously used in pure Arch uefi machines, is that /boot is a directory in the root partition, /. That way /boot is an ext4 directory and will contain the kernel and initramfs plus the rEFInd linux config file.
Then I can mount the EFI (vfat) partition as /boot/efi and so I can then make a /boot partition under /. Then the EFI /BOOT/ directory would be seen in Linux as /boot/efi/BOOT/ and the Windows efi stuff would be in /boot/efi/EFI/Boot/Microsoft/Boot/ in which case I would presume that I have to make a new directory in /boot/efi/EFI/refind/ and put the refind stuff including the filesystem drivers there, and let the kernel go into the (ext4) /boot/ directory which would be preferred! However I am not 100% confident that this is what will work and I need to read more before trying to do the install. The thing that concerns me is how the system will handle the uefi boot process, and whether it would auto-detect the Windows efi file as well as the Arch refind efi file once the system has started up?
... and then there is the issue of the NVRAM entries and I am no longer confident that if I use the usual tools to create an entry (efiboomgr or bcfg), that I will get a successful dual boot system!
There is still a chance that I would irrevocably damage being able to boot to the Windows and Recovery partition boot options by messing up the EFI and/or the NVRAM so I have to tread very very carefully with this.
If anyone has gone through this kind of dual boot install with a Windows 8 or 8.1 machine using rEFInd for the bootloader, and can offer advice or help here I would very much appreciate it. I have another pure Arch system which uses rEFInd that works extremely well, but it seems that dual boot with uefi is a rather more complex animal than a pure linux system!
Last edited by mcloaked (2014-02-22 10:06:03)

vipin wrote:I have recently bought the y510p , im planning to install Arch , this is my 4th laptop , i had installed Arch in all the other 3 with no problems, but im a bit worried with the installation as this is the first laptop which has EFI , im a linux user for the past 6 years , i started with fedora , now i like Arch , mike documentation is excellent, i just had one question when i had grub , it automatically finds the new kernel when i update (grub.conf/menu.lst gets updated), does rEFInd also do that.
When there is an update to the rEFInd package you need to copy the files across to your ESP from the files contained in /usr/share/refind/ usually you need to copy the refind_x64.efi binary as well as the icons, fonts, and drivers directories. Since there is flexibility in how you configure the kernel and initrd files in terms of where they are located whether you need to do anything else when a new kernel update arrives depends on how you set your system up. If you have the /boot directory as your ESP partition which will then have the kernel and initrd files updated by default then there no need to do anything else when there is a kernel update. If the ESP is then at /boot/EFI and within that is your refind/ directory then that is where the replacement files go if refind-efi gets a pacman update. So it is actually fairly straight forward. If you configure rEFInd to look for kernels in some other directory than /boot/ then you may need to copy the files there after a kernel update but there is more information in the arch wiki about this.
During a refind-efi package update there are helpful files in the pacman output (and log) reminding you of what you need to do. eg for the latest refind-efi update you get:
[2014-06-18 18:48] [PACMAN] upgraded radvd (1.12-1 -> 1.13-1)
[2014-06-18 18:48] [ALPM-SCRIPTLET]
[2014-06-18 18:48] [ALPM-SCRIPTLET] rEFInd UEFI application has been installed at /usr/share/refind/refind_*.efi
[2014-06-18 18:48] [ALPM-SCRIPTLET]
[2014-06-18 18:48] [ALPM-SCRIPTLET] Other UEFI applications have been installed at /usr/share/refind/tools_*/
[2014-06-18 18:48] [ALPM-SCRIPTLET]
[2014-06-18 18:48] [ALPM-SCRIPTLET] UEFI drivers have been installed at /usr/share/refind/drivers_*/
[2014-06-18 18:48] [ALPM-SCRIPTLET]
[2014-06-18 18:48] [ALPM-SCRIPTLET] Copy the efi application (according to your UEFI ARCH)
[2014-06-18 18:48] [ALPM-SCRIPTLET] and /usr/share/refind/refind.conf-sample to a sub-directory of <EFISYS>/EFI/
[2014-06-18 18:48] [ALPM-SCRIPTLET] as refind.conf and add an entry to firmware boot menu using efibootmgr
[2014-06-18 18:48] [ALPM-SCRIPTLET] or mactel-boot (for Macs)
[2014-06-18 18:48] [ALPM-SCRIPTLET]
[2014-06-18 18:48] [ALPM-SCRIPTLET] rEFInd Icons have been installed at /usr/share/refind/icons/
[2014-06-18 18:48] [ALPM-SCRIPTLET] rEFInd Fonts have been installed at /usr/share/refind/fonts/
[2014-06-18 18:48] [ALPM-SCRIPTLET]
[2014-06-18 18:48] [ALPM-SCRIPTLET] HTML Documentation is available at /usr/share/refind/docs/html/
[2014-06-18 18:48] [ALPM-SCRIPTLET]
[2014-06-18 18:48] [ALPM-SCRIPTLET] More info: [url]https://wiki.archlinux.org/index.php/UEFI_Bootloaders#Using_rEFInd[/url]
[2014-06-18 18:48] [ALPM-SCRIPTLET]
[2014-06-18 18:48] [PACMAN] upgraded refind-efi (0.8.1-1 -> 0.8.2-1)
I hope that helps.
By the way you can also boot uefi using grub and in fact you can get rEFInd to chainload grub as a backup bootloader as an added safety factor and have both rEFInd as well as grub installed simultaneously. How that can be done is explained in the thread at https://bbs.archlinux.org/viewtopic.php?id=181906
Last edited by mcloaked (2014-06-25 17:41:12)

Dual boot Arch and Windows XP (arch installed first) [solved]

I recently moved over to arch from Ubuntu, and would like to install Windows XP so that I can dual-boot between the two. However, my arch install created four partitions on my disk, and I can not create another one.
I would rather not have to reinstall arch, as setting it back up would take days on my current network connection. Is this possible? While I have installed XP over Ubuntu in the past (and am more than able to reform the MBR after the XP install) I have absolutely no experience with disk-partitioning, so concise instructions would be very much appreciated.
errata: my laptop has 4 gigs of RAM, so I don't think I need the SWAP partition. I am hesitant to delete it outright however.
this is a Gparted screenshot, running off of a Ubuntu live CD. The 60 gigs of unallocated space is where I was hoping to install windows.
Last edited by spotdart (2009-02-05 17:13:55)

What's on /dev/sda4? If you can blow away the last partition, turn the whole thing into an extended partition and then you can set up as many logical partitions as you want inside the extended partition. I suppose Arch is probably on sda4 and if that is the case you could move arch to sda3 first--there are lots of posts in the forum about how to move an installation of arch from one place to another.
Edit: Beat to the punch again. Yeah like he said you might want to delete the swap partition and then incorporate it into the 1st or third partitions so you can free up that last one.
Last edited by bgc1954 (2009-02-05 15:27:21)

[SOLVED] Triple Boot on Macbook 5,5 kills my arch install

I am currently trying to get a triple boot working on my mid 2009 macbook pro. I have 3 seperate partitions set up so that i can just launch the OS's with rEFInd.
Problem is.. as soon as I get all of them installed and up and running. I will try to boot cycle all of them to make sure everything is working as planned.
i boot OSX, everything is good
i boot Windows 7, again good to go.
as soon as i boot arch AFTER windows it kills the install it seems. the system will lock up at
starting version 217
/dev/sda6: recovering journal
/dev/sda6 clean, XXXXXX/xxxxxx files, XXXXXX/xxxxxx blocks
I am not quite sure how to find a log or anything since i cannot even boot into the system.
it ONLY happens after I boot into windows.
Already tested my ram per someone elses advice. everything turned out ok with that
the arch install works great if i only boot osx or arch.
I am not using bootcamp
i could chroot in and look for the log im just not sure where it would be.
i will gladly post that as well if i can get the location
Last edited by BoomZooka (2014-12-08 07:07:01)

ended up finally figuring out the issue
Figured out I couldnt see what was going on was, because I had a kernel parameter set as quiet for some reason. So it was not showing me anything which led me to run across a blog online that described system lockups at boot.
Added this to the kernel boot parameters in my grub.cfg on the linux line. After I did that everything booted like normal.
nomodeset reboot=pci
credits to http://dreamtimecircles.com/2013/10/06/arch/

[SOLVED] ARCH Install Freezes While making fallback image

Hi,
I am having some issues install arch on my desktop, the install is freezing while generating the 'fallback' image, this makes no sense to me as it has just compiled the main image, and should be the exact same.
I have run memtest x86 on each stick of ram (one at a time, and both in at the same time) with no errors.
I have tried both the X86_64 and the i686 both on CD and USB, and the install froze during the fallback kernel every time.
I am using the 2009.08 versions. and have downloaded the images from both mirror.internode and the main arch website link.
I have tried Zero filling the hard-drive with seatool, and it has passed a S.M.A.R.T HDD test (also on seatools)
I am just about to try a different distro just to check. I had arch installed last week but something went incredibly wrong during the last update, so i chose to format it and start fresh.
Any ideas?
Last edited by viruzeno (2010-02-09 12:11:29)

I have Worked out the problem. it seems my new blu-ray burner is having issues with linux, i need to track down a driver.
I disconnected the drive and the install finished fine. not too sure how it was causing the error.

HT1338 how do you perform a clean install for imac

How to perform a clean install for imac, because I cannot upgrade to version 10.6?

Here are the technical requirements for Snow Leopard:
http://support.apple.com/kb/sp575
If your iMac meets the requirements, then you will have to purchase the Snow Leopard disk from apple:
http://store.apple.com/us/product/MC573/mac-os-x-106-snow-leopard
To reinstall your OS, insert the original OS disk that came with your iMac and start up the iMac holding the C key. Start the installation process and when you see the menu bar, select 'Utilities'. From the drop down menu, select Disk Utility. Erase the HDD and the continue the installation.
Note that this will erase all data on the HDD so have it backed up before you start.
Ciao.

How I Got Boxee Working On A New Arch Install -- 3/12/2011

I thought I'd post a log of how one gets boxee-source working as of version 0.9.23.15885-2.
I recently built myself a new media center/apache server/seedbox and thought I would put arch on it. The Install was a breeze --- as far any arch install is concerned.
The only trouble I really had was with boxee --- usually available as a precompiled package, but (as is often the case) in either the AUR or an unofficial repo.
There wasn't very much useful (up-to-date) information in the boxee wiki page; I tried the repo listed but it required the python24 dependency to install, with which there are problems. See below.
There are a lot of problems with compiling boxee in arch at the moment, so I thought I'd list each one and what I did to get around them.
The three AUR packages in question:
http://aur.archlinux.org/packages.php?ID=24206
http://aur.archlinux.org/packages.php?ID=9898
http://aur.archlinux.org/packages.php?ID=16355
What I did:
* Downloaded boxee-source package (not the depreciated boxee package) from AUR (I used yaourt).
* Ran makepkg -si; saw what dependencies were required (also available in AUR web interface). Downloaded python24 and db4.5 dependencies.
* I noticed that db4.5 is an older version; my installed version is 5.1 !!!!
* To get python24 to compile, I had to edit the PKGBUILD script in python24:
1) First, remove this line:
[ -e /usr/lib/libdb.so ] && echo "make sure you have no other db* pkg installed" && return 1
2) Then, delete the "db4.5" dependency from "depends"
* After python24 compiled and installed (I deleted the db4.5 package source folders) I was able to being the boxee compilation process. However, I hit another roadblock when the compilation aborted at:
fatal error linux/smbno.h no such file
Based on comments in the AUR, I downloaded: http://dl.dropbox.com/u/5636456/smbno.h and put it in /usr/include/linux --- then the compilation would continue!
Finally, boxee was installed. However, one problem remained: boxee would not play videos. Literally nothing would happen when I chose a file to play.
I was able to fix this (again with the help of the AUR commentators) by editing the run-boxee-desktop file found in /opt/boxee/. I had to add this line:
export LD_PRELOAD=/usr/lib/libva.so
I had to add it in the same area the rest of the "exports" are in the file; which seemed odd to me. But after that, I was able to use boxee to maximum enjoyment.
Last edited by yochaigal (2011-03-17 06:52:04)

yochaigal wrote:The only peristent problem I'm having is that boxee randomly freezes when I play a video. I get audio but boxee freezes. if the window is maximized i can't unmaximize; i have to kill from tty or ssh. however, if it freezes with the window unmaximized, i can still move the mouse and do other things.
boxee log says this:
23:10:45 T:2770783088 M:1705168896 ERROR: CFileCurl::CReadState::Open, didn't get any data from stream. HTTP CODE: 0
23:10:45 T:3047160688 M:1705181184 ERROR: CFileCurl::CReadState::Open, didn't get any data from stream. HTTP CODE: 0
23:10:45 T:2834795376 M:1705181184 WARNING: CHttpCacheManager::UpdateRefMap negative reference count for url http://app.boxee.tv/applications/popularity (hcm)
23:10:45 T:2830584688 M:1705181184 ERROR: CFileCurl::CReadState::Open, didn't get any data from stream. HTTP CODE: 0
23:10:45 T:2839542640 M:1705054208 ERROR: CFileCurl::CReadState::Open, didn't get any data from stream. HTTP CODE: 0
23:10:45 T:2804353904 M:1705054208 ERROR: CFileCurl::CReadState::Open, didn't get any data from stream. HTTP CODE: 0
23:10:45 T:2751892336 M:1705054208 ERROR: CFileCurl::CReadState::Open, didn't get any data from stream. HTTP CODE: 0
23:10:45 T:2960128880 M:1704927232 ERROR: CFileCurl::CReadState::Open, didn't get any data from stream. HTTP CODE: 0
23:10:45 T:2770783088 M:1705181184 ERROR: CreateThumbnailFromMemory: exception with fileType: .png
23:10:45 T:2837953392 M:1705054208 WARNING: CHttpCacheManager::UpdateRefMap negative reference count for url http://app.boxee.tv/titles/sources (hcm)
23:10:45 T:2830584688 M:1705054208 ERROR: CreateThumbnailFromMemory: exception with fileType: .png
23:10:45 T:3047160688 M:1705054208 ERROR: CreateThumbnailFromMemory: exception with fileType: .png
23:10:45 T:3047160688 M:1705054208 ERROR: CFileCurl::CReadState::Open, didn't get any data from stream. HTTP CODE: 0
23:10:45 T:2751892336 M:1705054208 ERROR: CreateThumbnailFromMemory: exception with fileType: .png
23:10:45 T:2839542640 M:1705054208 ERROR: CreateThumbnailFromMemory: exception with fileType: .png
23:10:45 T:2960128880 M:1705054208 ERROR: CreateThumbnailFromMemory: exception with fileType: .png
23:10:45 T:2839542640 M:1705054208 ERROR: CFileCurl::CReadState::Open, didn't get any data from stream. HTTP CODE: 0
23:10:45 T:2804353904 M:1705054208 ERROR: CreateThumbnailFromMemory: exception with fileType: .png
23:10:45 T:2804353904 M:1705054208 ERROR: CFileCurl::CReadState::Open, didn't get any data from stream. HTTP CODE: 0
23:10:45 T:2960128880 M:1705054208 ERROR: CFileCurl::CReadState::Open, didn't get any data from stream. HTTP CODE: 0
23:10:45 T:2770783088 M:1705054208 ERROR: CFileCurl::CReadState::Open, didn't get any data from stream. HTTP CODE: 0
23:10:45 T:3047160688 M:1705054208 ERROR: CreateThumbnailFromMemory: exception with fileType: .png
23:10:45 T:2839542640 M:1705054208 ERROR: CreateThumbnailFromMemory: exception with fileType: .png
23:10:45 T:2804353904 M:1705054208 ERROR: CreateThumbnailFromMemory: exception with fileType: .png
23:10:45 T:2804353904 M:1705054208 ERROR: Texture manager unable to load file:
23:10:45 T:2960128880 M:1705054208 ERROR: CreateThumbnailFromMemory: exception with fileType: .png
23:10:45 T:2770783088 M:1705054208 ERROR: CreateThumbnailFromMemory: exception with fileType: .png
23:10:45 T:2770783088 M:1705054208 ERROR: Texture manager unable to load file:
I didn't notice this before. We are getting the same error messages in debug. Out of curiosity, do you have all pacman updates installed? I contacted the AUR maintainer for boxee-source, but his system is operating normally. Googling this " ERROR: CreateThumbnailFromMemory: exception with fileType: .png" I get a laundry list of php related stuff. My installed version of php is 5.3.6-1. Maybe it's somehow related?

Can't get Leopard to install on iMac G5

Can't get Leopard to install on iMac G5
Hi folks, I'm trying to install Leopard on my 20" iMac G5, but the install never completes. I get an error related to "essential package" failing or some such. I'm using a retail copy of Leopard.
I've read that many people have had trouble loading Leopard on the G5, but I don't now what the real problem is, or what the correct solution would be to making the install from the disc work.
I've also read that it might be a problem that the iMac G5s might not know how to read the install DVDs properly (despite the disc being verified earlier in the process).
I know the problem isn't the disc media because I have two separate retail DVDs of the Leopard installer (10.5.3). I tested them on other machines and they have worked. I even tried installing from a disc image of the installer, but no luck.
Any ideas?

The iMac appeared to work correctly under Tiger, but it did have a problem. I had just got un-repairable error on the 4-year old drive that came with the machine. I installed a new Seagate barracuda hard drive because of. This was all before the Leopard install attempts.
Permissions were all repaired. New drive and other HDs were all verified. All devices were disconnected for install attempts. Tons of space on newly formatted drive, as well as other external drives I tried this on. So it's not the media, and it's not the hard drives.
I am using third-party RAM. Tech tool indicates that it is okay. Perhaps I should try installing with only the RAM that came with the machine.
I contacted Applecare several days ago and they said the usual. Repair disc. Repair Permissions. Try install. No good? Then try reformat from Tiger and install Leopard on clean HD. No luck. The next thing they would suggest is forwarding the issue to a specialist within applecare.

How do i wipe and re install my imac

im trying to wipe and re install my imac any help appreciated i have no disc.

Welcome to the Apple Support Communities
If your iMac didn't come with DVDs, follow these steps:
1. Hold Command, Option (Alt) and R keys while your computer is starting to start in Internet Recovery. You may need to connect the iMac to a Wi-Fi network.
2. On the OS X Utilities window, open Disk Utility, select "Macintosh HD" on the sidebar, go to Erase tab and erase the disk.
3. Close Disk Utility and reinstall OS X.
This will reinstall the original OS X version that came with the iMac. If you want to reinstall the actual version, hold Command and R keys instead of Command, Option and R keys. The reinstall may take hours because the Mac has to download OS X from the App Store

How can I install my iMac's Aperture on my MacBrookPro

How can I install my iMac's Aperture on my MacBrookPro

What is your MacOS X version? Is your Aperture version the recent Aperture 3.5.1? Your profile signature "Mac OS 9.1.x? " cannot be right; do you mean Mac OS 10.9.1.x? And is the system the same on both Macs?
If you bought Aperture from the AppStore, launch the AppStore on your MBP:
Sign into the AppStore with the AppleID you used to buy Aperture on your iMac.
Download Aperture from the "Purchased" tab and let it install.
If you bought Aperture as a boxed retail version, use the Installer CD/DVD and serial number to install Aperture on your MBP.
If you bought Aperture online as a trial version, and bought a serial number to unlock the trial, use the trial installer you downloaded.
If you no longer should have the installation media or the downloaded trial installer, you can convert your working Aperture installation to an AppStore licence by upgrading your iMac version to Aperture 3.5.1. Then you can install and reinstall from the AppStore on all your Macs, if they are running Mavericks.

TS3824 How can we install the iMac Graphics Firmware Update if the screen is white and I can't get to the Apple menu?

How can I install the iMac Graphics Firmware Update 2.0, if the screen is white and I can't get to the Apple menu? My computer has 5 vertical purple lines against white screen at startup before the Apple logo appears and the spinning gear...then everything disappears and the screen hangs on the white screen. I have tried unplugging and removing all my peripherals and the COMMAND, OPTION, P & R set of keys and still nothing. I have tried COMMAND C to start up from cd and it only tells me to turn off the computer and turn it back on. I found information on Apple's Support pages regarding the iMac Graphics Firmware Update but I am unable to download and install if I can't get to the Apple menu. Can anyone help?

You may have hardware problem, I think a visit to your local Apple Store or AASP is in order.

Arch install experience / install CD uses devfs path names

Hey, all I'm new to the forums, very happy arch user. I can't remember how I found arch, it must've been fate. I did my share of distro hopping. Actually, I plunged into the deep end with my first Linux install by choosing to run Gentoo. To their credit I was able to get it installed by relying on their solid documentation, even though I was an absolute novice at the time. Still I had to leave Gentoo because on the whole I'm too impatient to compile every single program from source.
I then drifted to Mandrake for a short time, and then Fedora for a longer time. I became intimately familiar with dependency hell, and tracking down specific versions of libraries. I like using a few bleeding edge programs that are compiled out of CVS or SVN, and I found that it was a nightmare satisfying dependencies and dealing with package conflcts. I also ran Ubuntu for literally about 5 minutes. I won't get into why that lasted such a short time.
I was on irc the the other day in a dev channel for bmpx, attempting to get the newest version of bmpx to run (still am). One of the devs asked me if I was running FC4 (Fedora Core 4). My response:
Me: "I don't think I'd have a snowball's chance in hell of getting this working under FC."
Dev: "I'm running FC5."
I had to swallow my words. Here I am, a proud arch user with a seg faulting bmpx while the dev is running it on FC. Moral of the story: that guy must be a magician. That or FC is much more up to date now. Still, nothing could convince me to abandon pacman and go back to RPMs. Pacman is a Godsend. The whole ABS system is beautiful.
I just recently reinstalled a fresh version of arch after something of a hiatus. A while ago I borked my system (I had an ugly situation with my partition table, among other things) and I didn't get around to resurrecting my install for a while.
Now this was before Xorg7, and uDev, and ArchCK's move to initramfs. Obviously I was upgrading after those things were introduced. To further enrich this unhealthy mix, I have an ATI Radeon 9800, 2 ethernet cards (onboard), and 2 sound cards (PCI, and onboard). It might go without saying that I had a rocky install experience. It was like putting together a jigsaw puzzle blindfolded. Then I came to the Arch site and read about all the changes. Even then it was a messy experience, what with uDev simultaneously loading modules and whatnot (turns out that this can be a problem on systems with multiple soundcards or NICs). Finally after a boatload of troubleshooting, and much reading of the Wiki and the forum, I got everything setup. Queue angelic choir: I even got 3d acceleration via fglrx to work thanks to Iphitus's drivers, and posts in the forum by Cerebral.
So I'm once again a happy arch user, but I'm glad it wasn't my first arch install. My first install was ultra smooth by comparison.
If you're still reading you're probably wondering if I'm going to make a point. Well since, I'm new to the forum I figured I'd give a little background for anyone interested, and a little hope to to anyone wrestling with their install.
Actually I do have a question which I alluded to in the subject of this post. I did an FTP install from a CD I downloaded several months ago.
The Grub installer gives this message:
"Arch Linux supports two /dev device systems, DevFS and uDev. You can select the one you want by modifying your bootloader's configuration."
Obviously now only uDev is supported so that message is outdated. Plus the auto-generated fstab and menu.lst use the DevFS device paths by default.
So my question is do the newer install CDs generate fstab and bootloader config files using the uDev naming scheme or do they still default to DevFS? I realize I was using an older CD, but it was confusing not knowing that DevFS had been completely abandoned.
Also there should be an initrd line added to the autogenerated bootloader config (can't remember if it's there or not).
Maybe these issues have already been addressed in newer install CDs. Hopefully they have for the sake of first-time installers.
Whew okay I'm done, thanks guys.

jesus franco wrote:It seems you have 0.7 even though 0.7.1 fixes all those devfs,initrd issues.
Yea I think I do have the 0.7 CD. I just do FTP installs anyway so I didn't bother downloading a new CD. I was kinda guessing that the newer CD probably sorts out the uDev / DevFS issue but I wasn't sure. Nothing to worry about then!

Is the Arch install process the same as Mint's?

1.)Taking into consideation that it took me a few trys to even register for the forum (facepalms) and that I have only ever been a Mint user, how does the Arch install process compare to that of Mints?
2.)Will the install for a duel boot with Windows 7 be just as easy with Arch as it is with Mint?
3.)Are my questions an indication that I am probably not ready for Arch? (laughs)
4.)I really only use the Linux half of my duel boot when I am on unsecure networks while travleing and it makes me feel safer etc.. and when I do use it it's really just for browsing the internet. Should I just stick with Mint if thats all I really do?
I have heard only good things about Arch and if it's not going to make me want to rip out my hair, I would certinly like to reaplce Mint with Arch. Thank you for your time and help.

I came from Mint to Arch, via Debian and LFS. With regards to Grub, I'm still using the same grub installed by Mint two years ago, even though I no longer have Mint on the system. However, I do use a separate /boot partition and I'm comfortable editing grub.cfg directly when required. It does, however, mean that I never have to worry about adding a new OS for dual boot. Having said that, it's certainly not something I would suggest to anyone with limited experience.
Don't let others put you off with the "Arch is high maintenance" thing. If I'm honest, I don't find Arch significantly more high maintenance than any other Linux distro, though certainly during install and initial set up it helps if you have a reasonably good understanding of how the system is configured. Whereas the likes of Mint and other pre-built general distros have most of the system configuration done for you out of the box, on Arch you have to walk the extra mile and do it yourself. Linux is like women. The more you have to do to get them, the more you will get out of them in the end
Nevertheless, I fully agree with the "Test in a VM and get comfortable" philosophy first. This will help when you eventually come to a full install significantly. I did two test installs before a complete one, noting down where I had to pay particular attention. Also make sure that you don't need any firmware files, especially for network, when installing for real, or at least get the files and put them on a USB stick. Nothing worse than installing a system them not having any network to get the firmware required to get the network working. Catch 22 anyone?
Last edited by Roken (2012-04-23 10:46:23)

Arch install on Imac G5-SOLVED

Similar Messages

Maybe you are looking for