Arch is installed but grubs seems to not be

So i got a new pc today, it came with windows 7.
I partitioned and took half of the hdd for arch and made its partitions there.
All seemed to install well, but at the end, after i closed the last file you edit(that one about the boot), several errors came, i could not see them well because they disappeared quicly , but i could see "something could not be installed on /something/something/"
I rebooted and widows started, not the grub.
This is like what i did:
Cut in half 1Tb drive
made /dev/dsa{5,6,4} for root, boot and home
I know its very few information,sorry.

YamiFrankc wrote:
i fucked it up :S, accidentally destroyed windows.
ok, now, first i install windows, and after that i install arch, right?
https://wiki.archlinux.org/index.php/Wi … _Dual_Boot
According to that ^
Yes, it's better to install Windows first, leaving room for Linux.

Similar Messages

I have a DVD Acrobat Pro 9. I upgraded laptops and trying to install but the DVD is not readable. How can I get a new DVD or Download Acrobat Pro 1. The product is registered and I have the serial number. PS: Contacting Adobe on this issue is impossible..

I have a DVD Acrobat Pro 9. I upgraded laptops and trying to install but the DVD is not readable. How can I get a new DVD or Download Acrobat Pro 1. The product is registered and I have the serial number. PS: Contacting Adobe on this issue is impossible... direct support stinks.

Download AA 9 Pro from http://helpx.adobe.com/acrobat/kb/acrobat-downloads.html. Make a new backup for your archive. You might also take the DVD to your library to see if it is a drive problem. You might also carefully clean the DVD with water and soap (do not use anything that would scratch the surface or you have destroyed it for sure) and see if that solves the problem. This is particularly an issue if you have finger prints or other crud on the DVD. However, it could also be a bad drive as I mentioned. Hopefully the download solves your problem in any case (I would backup the download to CD and/or backup HD).

I have an Ipod touch and the latest software update was installed but it seems to be stuck on the IOS6 screen and I can not go anyfurther

I have an Ipod Tocuh which just had a software update to it. The screen is stuck on the IOS6 screen an I can not go any further.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Doing clean install but logic studio does not work. Getting Error message

I have my box Logic Studio 9 upgrade but it will not install on my SSD. Final cut and all other reinstalls worked. Cannot install LP 7 because it is a PPC
written program. Im trying to do a clean install of the lion OS but cannot get my most inportant program to install. I dont want to buy the program again at the app store. What do think my options are? I've had Logic since 6.0

Hi
First, get rid of your designer, the page design/code is a mess.
There are a number of problems with the page, not least being the disabling of the back button in all browsers I tested it in, (visitors may visit once with this, but are unlikely to do so a 2nd time).
The menu system is a fixed size so that when the browser is resized it overflows the browser window.
The use of tables for layout is not recommended as it is inaccessible to users using assistive devices.
To put this more politely, if you paid for this, ask for your money back. If you did not pay, then start again and use one of the dreamweaver layouts for your page, for more info, see - http://www.adobe.com/devnet/dreamweaver/articles/introducing_new_css_layouts.html.
PZ

NI-VISA is installed, but visa32.dll could not be loaded.

Hi,
When I start MAX, it shows the yellow exclamation mark icon and "VISA Error" under Devices and Interfaces.
The description of the error is "C:\Windows\system32\visa32.dll was found but could not be loaded."
I followed MAX's suggestion to repair the VISA installation but the error remains the same.
I also tried to uninstall and reinstall VISA again but it doesn't make any difference.
I'm using
NI-VISA 4.2
MAX 4.3
Best Regards
Tosko

I am quoting matt's reply to a similar problem
A complete uninstall is PROBABLY not necessary. Usually we can get
NI-VISA straightened out without destroying too much of what you have
done.
A) Yes, C:\Windows\System32\ is the correct place to be looking for
VISA32.dll. If it's not there, NI-VISA will have issues (any VISA for
that matter).
B) You definitely want this file to be put there by our installer, not
just placing it there. NI-VISA does install some reg-keys that have to
be there in order for it to run correctly.
C) Instead of doing a repair on NI-VISA, I would recommend an uninstall
(of only NI-VISA), then a reinstall of NI-VISA. Make sure you're using
the latest installer for your Windows.
Let us know if we can be of any more assistance.
Regards,
Matt S.

ITunes crashes when trying to access the iTunes Store -- Quick Time is installed but diagnostic says "QuickTime not available"

I'm getting a Windows error and iTunes crashes any time I try to access the iTunes store. I'm not sure if this may be related, but when I run a connectivity diagnostic, system info shows:
Microsoft Windows 7 x64 Home Premium Edition Service Pack 1 (Build 7601)
Gigabyte Technology Co., Ltd. EX58-UD3R
iTunes 10.5.0.142
QuickTime not available
I have QuckTime 7.7.1 (1680.42) installed and it works without trouble. Is the fact that iTunes doesn't recognize my install possibly related to the crashes? I have uninstalled and reinstalled both programs a couple times.

Well, as far as I can see, no one has responded to this question. Nor do I see any solutions mentioned in other questions by folks having the same problem. So I can only assume that there IS no fix.
Oh well, I know that one user is just "small potatoes" as far as the iTunes Store is concerned, but they've just lost this frequent little revenue stream - their loss, Amazon's gain.
Good-bye iTunes store - it was fun while it lasted...
Robert

Itunes shows app is installed but actually it is not!

FIFA 14 was downloaded by itunes on my pc. When i tried to transfer it to my iphone , it started syncing and finished.. but when I opened my iphone it shows that the app was only 75% installed. Not Fully. Later the icon turns gray. And the app is not installed.
Help me in this somebody ASAP Please.

Hi ...
Swipe left of your Home screen then type in the name of the app in the search field.
If it doesn't show up, follow the instructions here > Downloading past purchases from the App Store, iBookstore, and iTunes Store
If the app is no longer available, from that link: "Previous purchases may be unavailable if they are no longer on the iTunes Store."

My computer tells me Flash player is installed but the programme does not respond

Apparently Flash player is installed on my computer at the factory but does not respond and allow me to benefit!
Andrewgeraldo

Read Before Posting: How To Get A Useful Answer To Your Question

Downloaded Lion. Trying to install but the disk does not use GUID.

I tried to install lion on my Macbook Pro and when i try to it says that the disk doesnt use the GUID Partition Table Scheme and to go into Disk Utility and select the disk, click on the partition tab, choose the volume scheme, and click options. It wont let me click options. I was really looking forward to installing lion tonight. Any solutions?

wyattraymond wrote:
So install Snow Leopard on the Internal drive,
Yes.
then use migration assistant to bring stuff over.
At least two ways to do it. That's one. If you do it with MA, then run all updates before running MA. If you use Setup Assistant when you first restart after the installation, then run the updates after SA is finished.
Do i need to update at all after i migrate everything over since i installed 10.6.
Yes. The installer will only install the basic OS; depending on which installer you have, there will probably be a number of updates to download/install. You'll have to run Software Update and update everything listed there. As I said in an earlier post, I would not bring over anything system related.
or should the migration bring all the updates along with it?
No (see above).

When I download the updated version of flashplayer to my new updated firefox, flashplayer will say it has successfully installed, but it still does not work?

When I go back to look at something (movie, song, etc.), Firefox again tells me that I need to update the latest flashplayer in which I have already done. What could be wrong?I do not know if this is on my end or between both firefox and flashplayer. I have done everything possible that I know how and I have followed the directions carefully. Any help would be greatly appreciated! Thanks

There are two different versions of Flash for Windows, the '''''ActiveX''''' version for IE and the '''Plugin''' version used by Firefox and most other browsers.
1.Download the Flash Plugin version setup file from here: 
[http://fpdownload.adobe.com/get/flashplayer/current/install_flash_player.exe Adobe Flash - Plugin version]. 
Save it to your Desktop. 
2. Close Firefox using File > Exit 
then check the Task Manager > Processes tab to make sure '''firefox.exe''' is closed, 
{XP: Ctrl+Alt+Del, Vista: Shift+Ctrl+ESC = Processes tab}
3. Then run the Flash setup file from your Desktop.
4. Start Firefox and test your installation here: https://www.adobe.com/software/flash/about/
* On Vista and Windows 7 you may need to run the plugin installer as Administrator by starting the installer via the right-click context menu if you do not get an UAC prompt to ask for permission to continue (i.e nothing seems to happen). 
See this: 
[http://vistasupport.mvps.org/run_as_administrator.htm]

Upgrade of LR5 installed but LR 3 still not affected....Any Help?

I need help with the LR 5 which I haave upgraded but despite Installation being shown the LR3 still shows the LR3 face without the upgrade taking over.....

you need to change the default program that opens your files. what os?

I can´t install After Effects in my IMac because I think I have deleted this program in a bad way so my Mac show me After Effects like installed but the program is not installed...

How could I resolve this problem?

follow solution 2 here, CC desktop lists applications as "Up to Date" when not installed

Photoshop installed but not recongnized by Computer, updates fail

Hello,
I had installed CS6 Photoshop on my Windows 7 PC. Something happened where I see all the files and reference to Photoshop on the hard drive in the program files but I do not see an app icon to open the program. I also do not see the program listed in Control Panel so I can unistall it.
The Adobe App Manager seems to also recongnize it as installed. It offers me updates. When I update I get the following error message "U44M1P7 Error log file location C:\program files (x86)\ Common files\ Adobe installers
What do I need to do to fix this? If the app manager says it is installed but my computer will not recognize it to uninstall it what is my recourse?
Thanks.
Shannon

Hi Shannon,
You might try downloading and installing the Photoshop CS6 trial.
-Dave

Sonnet Encore Zif G4 Installed but will not boot.

I am back and feel like the frustrated enator. I called tech support at sonnet and got the upgrade installed but B&W will not boot.
I checked Sonnet tech page and I have no PCI cards installed and the hard drive that was attached out. However I can not get the power plug that was attached to it off could this be the problem. If so how does one pull it off?
I also read some place may have been a post at site the some 256 ram may not be compatable with up-grade. I have 4 sticks of pc 133 non ecc in the B&W. Problem?
I replaced them with 4 sticks of 64 ram pc 100 but still would not boot. Old ram that is untested.<

After doing the firmware upgrade on the G3 some memory that worked before the upgrade will either not work or will not be fully seen. I had a couple of 128M sticks in my g3 that only showed up as 64M after the firmware upgrade, and one 256 pc133 that did not work at all.
I seems you are trying to do three things at once: firmware upgrade, cpu upgrade, and memory upgrade. Doing all at once without confirming the success of each install makes troubleshoting your problem difficult.
Go back to ONE.
- take out the G4 upgrade
- put the original G3 cpu
- remove all but one stick of memory
- boot into OS9 with the one stick
-if no-boot then remove that stick, try another...
- confirm that the G4 firmware patch has been properly installed (do it again)
(even if you can not disconnect the power supply line from the PCI card thats fine as long as the card is not in the slot)
-after booting with one stick, reboot and add ONE stick of memory , confirm memory in System Profile. Continue untill you have all your memory confirmed and working in OS9
-once you have all of your installed memory working in OS9 boot into OSX, confirm the memory in System Profiler.
-if no boot in OSX remove all but one stick, try that.
-if one stick works, take it out and set it aside, try another, test each individually.
-install all the working sticks you have
-recheck that all the memory appears in System Profiler
-Now reinstall the G4 upgrade with just one confirmed working memory stick in.
-If that works put in one stick at a time and reboot, checking for the memory in System profiler each time.
If this works you should have a happy mac. If not you will be able to report back with exactly where problem is.
I know this is a lot of rebooting but IF you have a bad memory stick it is the only way to find it, and you have to ensure that all the memory is osx compatible before trying to install a cpu upgrade.

F4140 not working. cant remove, software says it's not installed but then wont re-install

The printer isn't working so I want to remove and re-install BUT the printer is not in Add/Remove Programs (I have XP). I downloaded the complete install package and tried to uninstall it that way, but the unistall program says nothing is installed. So I tried to install it but it says the software is already installed and doesn't install anything. I am really stuck this time. I wish HP had a "cleaner" utility because obviously the registry or something is out of synch. Please HELP!
This question was solved.
View Solution.

Hey there,
Here is how you can uninstall using the scrubber that is built into the software. I included both options on how to access the scrubber. Just choose whatever option is easiest for you.
Option 1: From Original installation CD:
1. Insert CD into drive, and then cancel the installer
2. Open My Computer, and then right click on the CD drive and chose open
3. Open folder Util
4. Open folder CCC
5. If you have an HP computer run the L3uninstall.exe. If you have a non-HP computer run the L4uninstall.exe
6. When the uninstall has completed restart the computer
7. Run Disk cleanup from Accessories\ System Tools
8. Download and install the latest version of Adobe flash player
http://www.adobe.com/support/flashplayer/downloads.html
9. Download the full feature software and drivers
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=al-64285-2&cc=us&dlc=en&lc=en&...
10. Run the download to reinstall the printer
Option 2: If software was downloaded and extracted to your system:
1. Type %temp% in the run field
2. Look for, and open the folder starting with 7z (Example: 7zS2356)
3. Open folder Util
4. Open folder CCC
5. If you have an HP computer run the L3uninstall.exe. If you have a non-HP computer run the L4uninstall.exe
6. When the uninstall has completed restart the computer
7. Run Disk cleanup from Accessories\ System Tools
8. Download and install the latest version of Adobe flash player
http://www.adobe.com/support/flashplayer/downloads.html
9. Download the full feature software and drivers
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=al-64285-2&cc=us&dlc=en&lc=en&...
10. Run the download to reinstall the printer
Hope this helps!
-Sean
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Arch is installed but grubs seems to not be

Similar Messages

Maybe you are looking for