Arch on a 2007" MacBook 2,1

I found these instructions but they are quite cryptic:
https://wiki.archlinux.org/index.php/Ma … sion_2.2C1
Could anyone help break this down into a step-by-step for me? The machine currently has OS X 10.4 on it which I'm happy to jettison or keep side-by-side.

That is a step by step guide... What about it is "cryptic"?
Not an Installation issue, moving to NC.

Similar Messages

  • 2007 Macbook with NVIDIA GeForce 8600M GT Repair

    Hi, I have a 2007 Macbook A1226 MB896LL/A which is showing all the signs of the GPU problems common to this model. Is apple still repairing them free of charge? Laptop does not chime,the fans are running, nothing on display but you can hear the hard drive chattering, it sort of boots to the point where if you increase/decrease the volume it makes the usual clicking sound, the keyboard backlight comes on if you cover the sensors, it ejects a CD if you press the eject key.

    Just take it to the Apple store and they run their NVIDIA diagnostic test, if it fails they will pull up your serial number and see if it's on the list to be replaced.  I have a early  2008 Macbook Pro and it had the tell tail signs of a failing Video card and they replaced the logic board at no cost to me.  Took it in on Thursday, got it back today (Sat), running like a champ.

  • I have a mid 2007 MacBook Pro with 2GB of RAM and NVIDIA GeForce 8600M graphics. Is it possible to upgrade the RAM and the graphics card?

    I have a mid 2007 MacBook Pro with 2GB of RAM and NVIDIA GeForce 8600M graphics card. Is it possible to upgrade the RAM and the graphics card?

    The RAM can be upgraded as indicated below. The Graphics card can not be upgraded.
    Maximum Memory
    6.0 GB (Actual) 4.0 GB (Apple)
    Memory Slots
    2 - 200-pin PC2-5300 (667MHz) DDR2 SO-DIMM

  • Late 2007 Macbook Pro: DVI to VGA Adapter

    I lost my DVI to VGA Display Adapter for my late 2007 Macbook Pro and can only find adapters for the PowerBook G4. Will this adapter work for my Macbook Pro?
    Thanks!

    Yes, all of those DVI+A to SVGA/VGA adapters for Macs are the same. I have adapters from the titanium G4, aluminum G4 and intel MBP and they all have DVI and came with adapters that function the same.

  • Late 2007 MacBook Pro S-Video adapter no output.

    I've troubleshooted everything I can, so hopefully one of you can help me!
    My Fiancé's mom has a late 2007 MacBook Pro running Mountain Lion. She has an older tv, so I was wanting to mirror the display so she can watch Netflix on her TV.
    After digging around on the Internet, other users said the APPLE M9267G/A adapter solved this problem without the need for a converter box, or upscaler. Needless to say, it doesn't work..
    I've tested the cable, port on the computer, and they both work. I've tried running just the yellow Composite video out instead of the S video through the video in on the TV, and a VCR... Nothing.
    I used my old Powerbook 1.67, which has an S Video out to the TV, and it works perfect. When I plug the adapter into the Powerbook's Dual Link DVI port, same port as the MacBook Pro, it doesn't work..
    I chose S-Video, even though the TV has Component inputs, because other forums said it wouldn't work without an expensive converter box.
    They said this would be the solution.
    Does anyone have any suggestions?
    Thanks!

    Same problem, though with an early-2008 MBP. Things worked fine with 10.6.x and as soon as I went to 10.9 the external display stopped working.
    The first time I plug in the adaptor (whether or not there is a video cable attached) the screen goes black and nothing shows up on the external screen. When I unplug the adaptor, I get the display back on the MBP but it's at low resolution and it has put me at the general login screen. When I put the adaptor back in the second time, it essentially locks up the display to where it is black and no key presses or adaptor removals brings the display back. I have to reset the MBP by holding down the power button. I submitted a bug report too, but have no faith Apple will do anything. Big fail, Apple.

  • Where can I buy an A1290 adapter for my 2007 MacBook Pro?

    HELP!
    My old computer's adapter has died but I still use this computer as a backup.. the only places I seem to be able to purchase a replacement adapter are Amazon / ebay and the sellers sound dodgy (fake adpater, breaks after a month etc).
    Can I not buy one of these direct from Apple???????????
    Thanks for any help in advance!
    Alice

    Alice,
    according to this Apple page, your 2007 MacBook Pro originally came with a 85 W adapter with a “T”-head. Apple no longer manufactures these; they’ve been replaced by “L”-head adapters, since they are supposed to withstand stress at the head better than the “T”-headed ones do. Since that page states that the “L”-head adapters can be used on models that originally came with the “T-head” adapters, you can buy the “L”-head analogue for your “T”-head adapter directly from Apple here.

  • I have a 2007 Macbook Pro that is running 10.7.5 and I am trying to use a 10.6.3 DVD to install Snow Leopard to an external hard drive.

    I have a 2007 Macbook Pro that is running 10.7.5 and I am trying to use a 10.6.3 DVD to install Snow Leopard to an external hard drive. I've followed every possible instruction on every which website. The problem is when I boot to Install disc, I am unable to choose which hard drive I'd like to install the OS on. It says that it is unable to Install and automatically takes me to Restore and suggests that I restore to Time Machine backups. Any and all help is appreciated.

    lovinlife5959,
    have you tried booting from the grey Mac OS X Install DVD that originally came in the box with your MacBook Pro? See if you can install its version of Mac OS X (either 10.4.9, 10.4.10, or 10.5.0, depending upon when it shipped from the factory) onto your external hard drive. If that works, boot from your external hard drive, run Software Update on it, and then try updating your external drive to 10.6.3 via the white Snow Leopard DVD.

  • Best way to upgrade our 2007 MacBook Pro to use Final Cut Pro

    Hello All.
    We have a 2007 MacBook Pro with 2 gigs ram, 160 Gig Hard drive and a 2.4 Mhz Intel Processor, and a 500 Gig Firewire External Harddrive.
    Is it feasable to upgrade this Laptop to run Final cut Pro?
    My girlfriend will edit small projects,i.e. vacation footage in H.D, Family Photo/Film montages, etc... nothing major
    Any advice much appreciated.
    Thanx

    Yes, Thanx
    We will not be using FCP X,  I think we have FCP 7,8 or 9, Not sure.
    I was thinking about More Ram from Other World ComputingLike this one:
    http://eshop.macsales.com/item/Other%20World%20Computing/5300DDR2S6GP/
    and maybe this Hardrive:
    http://eshop.macsales.com/item/Samsung/HNM101MBB/
    Just wanted some feedback about this, or other suggested hardware.

  • Can I use a 2009 iMac as external display for 2007 macbook pro with DVI port only

    I have a late 2009 imac with minidisplay port and  a 2007 macbook pro with DVI port. I connected a mini diaplay port to DVI cable but all I get on the imac is a blank screen when I press F2. Can I use the imac this way?

    I'm not sure if it works with DVI but your late 2009 must be a 27". Try Command-F2 or Copmmand-Fn-F2

  • [SOLVED] Arch Linux Duke (2007) Fails to Boot

    Folks, I have a unique and challenging problem that has exhausted my Arch Linux skills, and so I am now turning to you.
    I have a vintage Pentium Pro 200 system (that’s 200 MHz folks! – 200 MHz 686 architecture – the original 686!), two CPUs, running a dual boot between Windows NT 4.0 and Arch Linux Duke (2007). It has 512 MB of RAM and a 120 GB hard drive, partitioned up between Windows NT and Linux. I built this system new in 2007, hence the dated version of Arch.  It has run like a charm all these years, granted not getting that much use. After about a year of no use at all, I fired the system up last week to help with a little research for a blog post I was writing on networking Windows NT 4.0 and Mac OS 8.6. Windows NT 4.0 fired right up with no issue, and after I was done testing what needed to be tested I tried to boot over to Arch.
    After a year of disuse, Arch unexpectedly and stubbornly refused to boot. The boot process started up just fine, but towards the end, it declared that it could not mount the root file system on the root device and took a kernel panic and stopped. My Arch skills have gotten a bit rusty in the last few years, but I dusted them off and went to work. My guess was a file system or superblock error. Arch wouldn’t boot, but I dragged out my trusty RIPLinux 2.9 Rescue Live CD and fired it up. It came right up and ran, and I was able to mount the Arch partition and view all the files… everything seemed to be there; it just wouldn’t boot. Windows NT 4.0 AND RIPLinux both boot and run on the machine, so the hardware is fine as well.
    A little information on the disk layout. Windows NT 4.0 is in the first partition on the hard drive. The extended partition has a second Windows NT 4.0 partition (sort of a /home partition for Windows NT 4.0), followed by the main Arch partition (the one I am trying to boot), followed by a swap partition and then the largest partition, which I use to share data between Arch and Windows NT 4.0 (I have loaded an ext2/3 driver into Windows NT 4.0 and it happily accesses the Linux partitions on the box).
    RIPLinux’s e2fsck did find some issues with the Arch partition and I had it repair them all. I checked again afterwards that all the files were still there, and they were. With the partition now known to be clean, and the superblock repaired from one of the backups, all should have been well. However, Arch still wouldn’t (and still won’t) boot.
    RIPLinux has a kind of a chain loader function, so I had it attempt to start up Arch for me. However, this was flummoxed by the fact that Arch addresses all my hard drive partitions as /dev/sdax and RIPLinux addresses them as /dev/hdax. Hence, without a common language, it was hard to get the one to start the other. Still, using this function, I have been able to get a crippled version of Arch running on the machine again. No modules had been loaded, and so it couldn’t do almost anything, but there it was (and is), Arch Linux Duke, at the CLI level. From there, I can see all the files, I can move freely in and out of my user account and the root account, but I can’t make the thing actually boot properly.
    If you have read this far, you are a trooper.  Summarizing what I know, the hardware is good, the file system is clean, the superblock is good, I can mount it cleanly from a live CD and I can chain load a crippled version of Arch. Here is the boot process blow-by-blow. When I try to do a normal boot, the Windows NT 4.0 loader passes control to the Lilo boot sector I have placed on hda1 (sda1 in Duke’s parlance). Lilo takes over, present a menu and when I select Duke, takes off. Arch Linux Duke starts to boot. It gets a good long way along, all the way along to:
    :: Loading udev events                [Pass]
    :: Mount root Read-only
    :: Checking file systems
    This is where it stops.
    The next thing I see is:
    /dev/sda6
    The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else) then the superblock is corrupt and you might try running e2fsck with an alternate superblock:
        E2fsck –b 8193 <device>
    I then get a sort of character based splash screen that says
    **********FILE SYSTEM CHECK FAILED ****************************
    *   Please repair manually and reboot. Note that the root file system
    *   is currently mounted read-only. To remount it read-write, type:
    *   mount –n –o remount,rw /.  When you exit the maintenance
    *   shell, the system will reboot automatically
    Give root password for maintenance
    At this point, I give the root password and enter the maintenance shell as root. I typed in “mount” and the first entry I got back is
    /dev/sda6 on / type ext3 (rw)
    This is exactly the root partition that the start up complains about. It is clearly there.  I can see it, I can walk around it… it is clearly there. Why won’t it boot? Despite the message, the superblock is fine – it passes every test e2fsck can throw at it.
    At this point, I did a “e2fsck /dev/hda6 (which is how RIPLinux would have passed it into Arch” and it says it is “clean”. I suspect that the Superblock message is because Arch sees root as sda6, while RIP passed it in as hda6...
    Deciding to see what Arch would be seeing as it tried to set things up in the boot sequence, I tried the following next:
    # mknod “/dev/root2” b 3 6   
    (“3” because RIPLinux refers to my hard drive as IDE, while Arch refers to it by major number “8”, which is SCSI. By the way, it IS an IDE drive – not sure why Arch insists on using the sdx nomenclature instead of hdx)
    Then I entered “mount /dev/root2 /mnt/hda6” and “ls /mnt/hda6”
    All was well. I can make the node, I can mount it, and I can see the contents. All is clearly well, but something is clearly wrong enough that Arch can’t boot.
    I am totally out of ideas. I have tried every trick I know and am out of tricks. I would welcome any insights as to what I could try to get this venerable Arch installation back on its legs.
    By the way, the key section of the /etc/lilo.conf file (lest anyone want to know) is:
    image = /boot/vmlinuz26
       root = /dev/sda6
       label = ArchLinux-Duke
       initrd = /boot/kernel26.img
       read-only
    I am stumped. Thanks in advance for any and all pointers you may be able to offer.
    Last edited by mac57 (2014-06-02 17:42:21)

    Folks, thanks for all your helpful comments, and I wanted to report back to you that I finally overcame the issue, and ArchLinux-Duke (2007) is once again executing flawlessly on my old Pentium Pro 200 system. I won't bother reporting here all the blind allies I went down as I tried to figure out what was wrong, but in the end, literally moments before I was about to give up and overwrite my Arch installation with a new Linux variant (antiX seemed well suited for such old and low power hardware), my attention was drawn to a note I had made in my files back in 2007 about a problem with similar symptoms. In that case, I had just deleted ZenWalk Linux from the hard drive (both Arch and Zen had been on the drive), and merged several partitions to make use of the newly free space. This had changed Arch's view of the drive lettering, and what had been its /dev/sddx root device was now /dev/sdcx. Arch failed to boot, throwing off the same errors I was seeing now. I wish I had recalled that note a month or so ago! It would have saved me a lot of work and a lot of frustration.
    At any rate, as a last step, and testing the idea that maybe the drive lettering had changed for some reason, I repeatedly manually booted Arch, specifying root=/dev/sda6, then /dev/sdb6, then /dev/sdd6, and finally, /dev/sdc6. Eureka! Arch now considered itself to be on /dev/sdc6 whereas previously it had been on /dev/sda6. This got me part way there, but the boot failed at the filesystem check stage and threw me into root. I disabled the file system check in /etc/rc.sysinit and got farther. Then I cleaned up /etc/fstab to agree with the new sdc naming, and I was back on the air fully.
    So, what had happened was that Arch had changed its view of the drive it was on from sda6 to sdc6. While I could not understand why this "sudden" change had occurred, at least I had a solution, and had Arch back up and running.
    Trolling through the rest of my notes, I found the answer. In 2012, the Tekram SCSI card in the machine failed, and I ultimately replaced it with an Adaptec card. The Tekram card did not have a BIOS segment on it. The Adaptec card did. My guess is that this caused the two internal SCSI devices I have built into the system (Iomega ZIP and Jaz respectively) to be enumerated first, claiming the "sda" and "sdb". device names. That left "sdc" for the root device, and that is where Arch went next.  This is my guess anyway.
    I should have caught this issue back in 2012, at the time, but from my notes, I can see that I tested the new card thoroughly using the  Windows NT 4.0 side of the machine, but never thought to bring up Arch as well. Hence, this problem lay dormant for two years, before I attempted to fire up Arch last month and blundered right into it.
    It has not all been bad. I have learned more about the ext2 and ext3 file systems and superblocks in the intervening time than I will ever need to use. I have learned how to manually boot Linux on a machine whose BIOS is so old that it cannot address the disk cylinder that the kernel is on and I have completely refreshed the many general Linux skills that used to just flow from my finger tips. It has been a frustrating experience, but ultimately a successful and useful one.
    Just wanted to let everyone know that this is now [SOLVED]. I would mark the post as such, but I don't see any obvious way to do that. Thanks again everyone.

  • I can only run Windows on my Mid 2007 MacBook Pro :(

    So, a weird thing happened recently.  A friend of mine was trying to get his old PowerMac G4 working, but his DVD drive wasn't working, so I booted my computer into Target Disk mode so that we could restore his computer using my DVD drive.  After we were able to get it installed, I tried to reboot my computer back into Mountain Lion.  Upon restarting the computer, I noticed that the OS wouldn't boot.  After playing with that for a little while, I backed up my files onto another iMac (again, using Target Disk mode) and tried to reinstall the OS.  When I put in the Mountain Lion DVD and tried to boot from it, it didn't work.  So I tried my Lion disk, also didn't work.  Tried Snow Leopard and was able to get it to install, but I wasn't able to use my keyboard and mouse upon getting to the "Select Language" screen.  I finally thought "screw this" and made an appointment with an Apple Genius (who was quite helpful) at the Apple Store near me.  I showed up and we tried a bunch of things to no avail.  He ran the Apple Hardware Test and that nothing was wrong with the computer.  I did have non-apple RAM in my computer, so we tried switching that out.  No luck.  I also told him that I switched Hard Drives to another 320 GB to try and see if that was the problem. That wasn't the fix either.  After trying all of that stuff, I tried installing Windows 7, and ironically enough (since its an Mac), and it worked.  I am now using my Mid 2007 MacBook Pro with Windows 7 only and I still can't install MacOS (which I miss big time!).  The Genius said that he had never seen this before and was at a loss (couldn't think of another thing to try).  Instead of leaving it with them, I took it home with me as I needed a computer for School as I am a High School Teacher.  I also am a bit of a Computer Engineering guy (built my own computers, been installing OSes for 10 - 15 years, etc) and while I like to consider myself a modest person, I will call myself a self proclaimed expert.
    Has anyone heard / seen this happen?
    I've searched high and low on the internet for this and haven't found anything.  ****, even the Genius has never heard of anything and gave me his business card and told me to drop him a line if I am able to figure out the problem.
    I'm really hoping someone can help me shed some light on this subject as I feel like I have tried completely everything.
    Thanks in advance,
    Todd

    Take your MBP to an Apple store genius bar for a free diagnostic examination.  Since these symptoms are 'regular' and not intermittent, they should be able to determine what the problem is and the cure.
    ciao.

  • What is max internal hard drive transfer rate compatible with a 2007 MacBook Pro?

    In attempt to upgrade my mid-2007 MacBook Pro (Intel Core 2 Duo), I bought a Seagate 750GB listed as compatible with my computer on MacSales.com . . .
    Seagate Momentus XT ST750LX003 750GB 7200 RPM 32MB Cache 2.5" SATA 6.0Gb/s Solid State Hybrid Drive -Bare Drive
    Installation appeared to go well and I ran an extended hardware test with no issues found.  However, the drive is listed at 5.46 TB (would be nice) and I get an input/output error when attempting to partition.  I can initiate an erase, but after the time I would suspect it would take to erase the drive, I get an input/output error - it seems to appear after the first 750 GB of the '5.5 TB' was erased.  At all times, the drive is not recognized when I attempt to install OS X from original discs.
    I suspect the 6.0 GB/s transfer capacity of the hard drive is not compatible with the MacBook Pro.  The drive came with 4 jumper pins but no jumper and no label diagram to set a slower transfer rate.  I called Seagate, Newegg, OWC, and Apple, but no one has compatibility info for my MacBook Pro.  To them, it appears I am running the first tests of this new technology with an 'older' MacBook Pro.
    My MBP has had no issues - I'd like to keep her going with the optimum internal hard drive capacity, but don't necessarily want to set up a test bench in my house (though my kids would enjoy destroying it) and pay several shipping and restocking fees to test new hard drives.
    The original drive had a 1.5 GB/s transfer rate.  Does anyone know the maximum transfer rate compatible with a 2007 MacBook Pro?  3.0 GB/s?  1.5 GB/s?  Thank you.

    No spinning hard drive will transfer data faster then 60-80MB a second. The XT models have a flash storage area that is used when reading and writing data that can make it Appear faster in some situations. That flash memory if only 8 or 16GBs in side, I forget which one.
    The drie is rated to work on 6GB SATA bus but it certainly can not transfer data that fast. It should be backword compatible to work on slower buses.
    Your drive is 750GBs in size. Not wure where you are getting this 5.5TB (that is 5.5 Tera Bytes which is 5500 Giga Bytes. Your drive is under 1TB)
    What are you using to partition the drive? Disk Utilities from the original install DVD?
    You need to install on your old drive, Update it from the Apple Website then clone it to the new drive. The version of OSX you are using may not function correctly with that large of a drive. Or get yourself a copy of Snow Leopard, retail disk for $29 from Apple, and do all the partitioning and installing with that version od OSX.

  • My 2007 Macbook pro Intel Core 2 Duo   Processor Speed 2.33 GHz has power issues with one or some of my USB powered devices. Last night I could not back up my Lacie external drives with software SuperDuper, hard drive copier. I also had a message that Tim

    My 2007 Macbook pro Intel Core 2 Duo   Processor Speed 2.33 GHz has power issues with one or some of my USB powered devices. Last night I could not back up my Lacie external drives with software SuperDuper, hard drive copier. I also had a message that Time machine failed. I have two powered 12V USB
    routers that are plugged into a 550VA CyberPower surge protector. I often receive these insufficient USB power for devices messages a dozen times even when I do not have devices like camera, Ipad, Ipod, and Tascam digital audio recorder plugged in. Is there a way to troubleshoot these USB routers or should I consider that one of the routers may be defective and replace them?
    David

    My 2007 Macbook pro Intel Core 2 Duo   Processor Speed 2.33 GHz has power issues with one or some of my USB powered devices. Last night I could not back up my Lacie external drives with software SuperDuper, hard drive copier. I also had a message that Time machine failed. I have two powered 12V USB
    routers that are plugged into a 550VA CyberPower surge protector. I often receive these insufficient USB power for devices messages a dozen times even when I do not have devices like camera, Ipad, Ipod, and Tascam digital audio recorder plugged in. Is there a way to troubleshoot these USB routers or should I consider that one of the routers may be defective and replace them?
    David

  • I want to pgrade to an SSD drive in my Mid 2007 MacBook. What SATA hard drive can I install 2 or 3??

    I want to pgrade to an SSD drive in my Mid 2007 MacBook. What SATA hard drive can I install 2 or 3?? That seems to be just about all I can find out there, so far. Are those drives compatable with this macine?  thx

    SATA II

  • Can I use a 2011 Macbook Pro charger for my 2007 Macbook?

    My charger for my 2007 Macbook works as an AC adapter, but will not charge my battery. My girlfriend has a new Macbook pro and I want to know if I can use her charger to charge my battery. I know they output different wattages, but I'm not sure how that will affect it. I have heard rumors that new Pro chargers will fry the batteries of the older Macbooks but I don't know if there is any truth to that. Thank you in advance for any help you can provide.

    You can use a higher wattage charger to charge a mac that normally uses a lower wattage charge and that is fine.  You do not want to do the opposite.

Maybe you are looking for