ARD: Deploy Final Cut Studio
Relative newbie to ARD. I have to deploy Final Cut Studio to 17 iMacs in a lab that already are in production. I would have expected to find more information available on how to accomplish this task, especially with this software since it is Apple software.
I cannot seem to find anything definitive that explains if this is possible or that can be used as a guide to doing so.
Anyone care to share any pointers? Links? How Tos?
Hello,
A no go there my friend, because Final Cut studio is multi-disc installer and requiring the serial number during the install.
The best thing you could do is to make a disk images of Final Cut, then push them over the network with ARD to the iMac's & then run the installer manually on each via screen sharing. When your done use ARD to send a task to delete the images of the iMac's.
Hope this help's!
Here's are some resources -
http://images.apple.com/remotedesktop/pdf/ARDAdmin_Guidev3.3.pdf
And Apple site - http://www.apple.com/remotedesktop/resources.html
Message was edited by: macpos.co.uk
Similar Messages
-
Can Remote Desktop install Final Cut Studio?
Hi,
I'm planning a large rollout of Final Cut Studio 3 to a network of 36 MacPro's. I use Apple Remote Desktop to install as much as possible, but I've never been able to install Final Cut using ARD due to it being a multi-disc installer and requiring the serial number during the install. The best I've been able to do is push installer disk images out to the computers, then run the installer manually on each via screen sharing. Not horrible, but a lot more time consuming than it should be.
I don't see anything in the Final Cut Studio installer on using ARD, but I thought I'd check here.
Thanks,
MitchThanks. My method thus far is similar. I image each disc to a folder, then put the discs away (pretty much standard procedure for any install really). Remote Desktop lets you push the image files out to all computers simultaneously - freakishly fast using multicast networking. The image files are then local to each machine. I'll then sit at the admin station, and using Remote Desktop's screen sharing jump between each computer starting the installer and pasting the serial number. When done, I trash the installer image files from the local computers.
I've played with imaging full systems, but I always think of "one last thing" that needs to be done to configure then I'm back imaging again.
Most applications that use the pkg/mpkg installer format install great over Remote Desktop. Even some that have serial number entry during install have workarounds (Filemaker lets you create a plist containing the serial for example). Even Adobe has come around with CS4, not using the standard format but packaging their multi-disc installer with configuration info for simple network installs. -
Final Cut Studio 2: Requirements and Recommendations
Hello Final Cut Studio 2 Experts,
I'm considering purchasing Final Cut Studi 2, and to make sure that I'll benefit from the full range of specific application (FCS/motion/color...) and I'd like to ask few questions (5 main points) regarding requirements and recommendations. So, please be prepared for much reading as I am not an expert on the matter. I like to know if my computer accepts any further hardware parts highly recommended and if I can purchase and install them myself. And yes, you should also know that I intend to use a Panasonic multi-format (HD/SD) camera for capturing and exporting videos.
N.B. Please note that the full list of my Hardware contents appear at the bottom of this text.
THANKS IN ADVANCE for your expert advise!
So, here we go:
Application-Specific Requirements
Final Cut Studio
Capturing HD resolution video using the ProRes 422 format requires a Mac Pro with an Intel Xeon processor or a G5 Quad computer and a qualified third-party capture card.
1) Do I need an Intel Xeon processor? If yes, can I purchase and install the component by myself (like RAM)?
Motion
The standard graphics card in any Mac Pro, MacBook Pro, iMac with Intel Core Duo, Power Mac G5, or iMac G5; 1.25GHz or faster PowerBook G4; or 1.25GHz or faster flat-panel iMac:
ATI Radeon 9800, 9700 Pro, 9600 XT, or 9600 Pro
ATI Mobility Radeon 9700 or 9600
NVIDIA GeForce 7600 GT, 7300 GT, 6600, 6600 LE, FX Go5200, or FX 5200 Ultra
For 16- and 32-bit rendering: a graphics card with at least 128MB of VRAM
2) Do I need one of the ATI Radeon 9800, 9700... or ATI Mobility Radeon? Why does my Hardware contents say ATI Radeon 9600, and not ATI Mobility Radeon 9600, is there a difference?
Color
The standard graphics card in any Mac Pro, 17-inch MacBook Pro, 24-inch iMac with Intel Core Duo, or 2.5GHz or faster Power Mac G5 Quad:
ATI Mobility Radeon X1600
ATI Radeon X1600
NVIDIA GeForce 7800 GT, 7600 GT, 7300 GT, 6600, or Quadro FX 4500
A display with 1680-by-1050 resolution or higher
A three-button mouse for full functionality
3) Do I need and ATI Mobility Radeon X1600 or ATI Radeon X1600?
DVD Studio Pro
For playback of DVD Studio Pro 4-authored HD DVDs: a Macintosh computer with a PowerPC G5 or Intel Core Duo processor
For writing finished projects to disc: an Apple SuperDrive or other DVD recorder
For writing finished projects to a double-layer disc: a double-layer-compatible recorder and double-layer media
For transporting HD projects to a replicator: an external drive or Internet transfer of the project’s disk image
For transporting SD projects that contain copy-protection or dual-layer features to a replicator: a DLT drive, external drive, or Internet transfer of the project’s disk image
4) Do I have an Intel Core Duo processor? Do I need an Apple SuperDrive?
What is a "replicator"?
Application-Specific Recommendations
Motion
One of the following graphics cards is highly recommended:
ATI Radeon X1900 XT, X850 XT, X800 XT, or X1600
NVIDIA GeForce 7800 GT, 6800 Ultra DDL, 6800 GT DDL, or Quadro FX 4500
For 32-bit rendering: a graphics card with 256MB of VRAM or more
Color
The following graphics card is highly recommended:
ATI Radeon X1900 XT
Dual displays with 1920-by-1200 or higher resolution
5) Do I have one of the highly recommended cards ATI Radeon X1900 XT etc...? How do I get it and can I install it myself?
My Power Mac G5 HARDWARE CONTENTS:
Hardware Overview:
Machine Name: Power Mac G5
Machine Model: PowerMac7,3
CPU Type: PowerPC G5 (3.0)
Number Of CPUs: 2
CPU Speed: 2.3 GHz
L2 Cache (per CPU): 512 KB
Memory: 4.5 GB
Bus Speed: 1.15 GHz
Boot ROM Version: 5.2.4f1
Serial Number: G85167AGRU3
ATA Bus:
SONY DVD RW DW-Q28A:
Model: SONY DVD RW DW-Q28A
Revision: KAS7
Serial Number:
Detachable Drive: No
Protocol: ATAPI
Unit Number: 0
Socket Type: Internal
SONY DVD RW DW-Q28A:
Model: SONY DVD RW DW-Q28A
Revision: KAS7
Serial Number:
Detachable Drive: No
Protocol: ATAPI
Unit Number: 0
Socket Type: Internal
Built In Sound Card:
Devices:
Texas Instruments TAS3004:
Inputs and Outputs:
Line Level Input:
Controls: Left, Right
Playthrough: No
PluginID: TAS
Headphones:
Controls: Mute, Left, Right
PluginID: TAS
Internal Speakers:
Controls: Mute, Master
PluginID: TAS
Line Level Output:
Controls: Mute, Left, Right
PluginID: TAS
Crystal Semiconductor CS84xx:
Inputs and Outputs:
S/PDIF Digital Input:
Controls: Mute
Playthrough: No
PluginID: Topaz
S/PDIF Digital Output:
Controls: Mute
PluginID: Topaz
Formats:
PCM 16:
Bit Depth: 16
Bit Width: 16
Channels: 2
Mixable: Yes
Sample Rates: 32 KHz, 44.1 KHz, 48 KHz
PCM 24:
Bit Depth: 24
Bit Width: 32
Channels: 2
Mixable: Yes
Sample Rates: 32 KHz, 44.1 KHz, 48 KHz
AC3 16:
Bit Depth: 16
Bit Width: 16
Channels: 2
Mixable: No
Sample Rates: 32 KHz, 44.1 KHz, 48 KHz
Bluetooth: No Information Found.
SONY DVD RW DW-Q28A:
Firmware Revision: KAS7
Interconnect: ATAPI
Burn Support: Yes (Apple Shipped/Supported)
Cache: 2048 KB
Reads DVD: Yes
CD-Write: -R, -RW
DVD-Write: -R, -RW, +R, +RW, +R DL
Burn Underrun Protection CD: Yes
Burn Underrun Protection DVD: Yes
Write Strategies: CD-TAO, CD-SAO, CD-Raw, DVD-DAO
Media: No
Fibre Channel: No Information Found.
FireWire Bus:
Maximum Speed: Up to 800 Mb/sec
ATI Radeon 9600:
Chipset Model: ATY,RV351
Type: Display
Bus: AGP
Slot: SLOT-1
VRAM (Total): 128 MB
Vendor: ATI (0x1002)
Device ID: 0x4150
Revision ID: 0x0000
ROM Revision: 113-A58504-113
Displays:
Cinema HD Display:
Display Type: LCD
Resolution: 1920 x 1200
Depth: 32-bit Color
Core Image: Supported
Main Display: Yes
Mirror: Off
Online: Yes
Quartz Extreme: Supported
Rotation: Supported
Display:
Status: No display connected
DIMM0/J11:
Size: 256 MB
Type: DDR SDRAM
Speed: PC3200U-30330
Status: OK
DIMM1/J12:
Size: 256 MB
Type: DDR SDRAM
Speed: PC3200U-30330
Status: OK
DIMM2/J13:
Size: 1 GB
Type: DDR SDRAM
Speed: PC3200U-30330
Status: OK
DIMM3/J14:
Size: 1 GB
Type: DDR SDRAM
Speed: PC3200U-30330
Status: OK
DIMM4/J41:
Size: 1 GB
Type: DDR SDRAM
Speed: PC3200U-30330
Status: OK
DIMM5/J42:
Size: 1 GB
Type: DDR SDRAM
Speed: PC3200U-30330
Status: OK
DIMM6/J43:
Size: Empty
Type: Empty
Speed: Empty
Status: Empty
DIMM7/J44:
Size: Empty
Type: Empty
Speed: Empty
Status: Empty
PC Cards: No Information Found.
PCI Cards: No Information Found.
Parallel SCSI: No Information Found.
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 0
Display Sleep Timer (Minutes): 0
Dynamic Power Step: No
Reduce Processor Speed: No
Sleep On Power Button: Yes
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On LAN: No
Wake On Modem Ring: No
Adobe PDF 7.0:
Status: Idle
Print Server: Local
Driver Version: 10.4
Default: No
URI: pdf700://distiller/
PPD: Adobe PDF 3016.102
PPD File Version: 1.0
PostScript Version: (3016.102) 0
hp LaserJet 1012:
Status: Idle
Print Server: Local
Driver Version: 1.4.5
Default: Yes
URI: usb://Hewlett-Packard/hp LaserJet 1012?serial=00CNFB638356
PPD: hp LaserJet 1012
PPD File Version: 1.0
PostScript Version: (3011.104) 0
Serial-ATA Bus:
Maxtor 6B250S0:
Capacity: 233.76 GB
Model: Maxtor 6B250S0
Revision: BANC1E50
Serial Number: B61QB0RH
Removable Media: No
Detachable Drive: No
BSD Name: disk1
Protocol: ata
Unit Number: 0
Socket Type: Serial-ATA
Bay Name: "A (upper)"
OS9 Drivers: No
S.M.A.R.T. status: Verified
Volumes:
Macintosh HD:
Capacity: 233.64 GB
Available: 50.02 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk1s3
Mount Point: /
Maxtor 6B250S0:
Capacity: 233.76 GB
Model: Maxtor 6B250S0
Revision: BANC1E50
Serial Number: B61QB0RH
Removable Media: No
Detachable Drive: No
BSD Name: disk1
Protocol: ata
Unit Number: 0
Socket Type: Serial-ATA
Bay Name: "A (upper)"
OS9 Drivers: No
S.M.A.R.T. status: Verified
Volumes:
Macintosh HD:
Capacity: 233.64 GB
Available: 50.02 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk1s3
Mount Point: /
Serial-ATA Bus:
Maxtor 7L300S0:
Capacity: 279.48 GB
Model: Maxtor 7L300S0
Revision: BANC1E00
Serial Number: L602X73H
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Protocol: ata
Unit Number: 0
Socket Type: Serial-ATA
Bay Name: "B (lower)"
OS9 Drivers: No
S.M.A.R.T. status: Verified
Volumes:
Primo Volume:
Capacity: 279.36 GB
Available: 154.23 GB
Writable: Yes
File System: HFS+
BSD Name: disk0s3
Mount Point: /Volumes/Primo Volume
Maxtor 7L300S0:
Capacity: 279.48 GB
Model: Maxtor 7L300S0
Revision: BANC1E00
Serial Number: L602X73H
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Protocol: ata
Unit Number: 0
Socket Type: Serial-ATA
Bay Name: "B (lower)"
OS9 Drivers: No
S.M.A.R.T. status: Verified
Volumes:
Primo Volume:
Capacity: 279.36 GB
Available: 154.23 GB
Writable: Yes
File System: HFS+
BSD Name: disk0s3
Mount Point: /Volumes/Primo Volume
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBOHCI
PCI Device ID: 0x0035
PCI Revision ID: 0x0043
PCI Vendor ID: 0x1033
Bus Number: 0x2b
Hub in Apple Pro Keyboard:
Version: 4.10
Bus Power (mA): 500
Speed: Up to 12 Mb/sec
Manufacturer: Mitsumi Electric
Product ID: 0x1003
Vendor ID: 0x05ac (Apple Computer, Inc.)
Apple Optical USB Mouse:
Version: 3.40
Bus Power (mA): 100
Speed: Up to 1.5 Mb/sec
Manufacturer: Logitech
Product ID: 0x0307
Vendor ID: 0x05ac (Apple Computer, Inc.)
Apple Pro Keyboard:
Version: 4.10
Bus Power (mA): 250
Speed: Up to 12 Mb/sec
Manufacturer: Mitsumi Electric
Product ID: 0x020b
Vendor ID: 0x05ac (Apple Computer, Inc.)
Hub in Apple Pro Keyboard:
Version: 4.10
Bus Power (mA): 500
Speed: Up to 12 Mb/sec
Manufacturer: Mitsumi Electric
Product ID: 0x1003
Vendor ID: 0x05ac (Apple Computer, Inc.)
Apple Optical USB Mouse:
Version: 3.40
Bus Power (mA): 100
Speed: Up to 1.5 Mb/sec
Manufacturer: Logitech
Product ID: 0x0307
Vendor ID: 0x05ac (Apple Computer, Inc.)
Apple Pro Keyboard:
Version: 4.10
Bus Power (mA): 250
Speed: Up to 12 Mb/sec
Manufacturer: Mitsumi Electric
Product ID: 0x020b
Vendor ID: 0x05ac (Apple Computer, Inc.)
Apple Optical USB Mouse:
Version: 3.40
Bus Power (mA): 100
Speed: Up to 1.5 Mb/sec
Manufacturer: Logitech
Product ID: 0x0307
Vendor ID: 0x05ac (Apple Computer, Inc.)
Apple Pro Keyboard:
Version: 4.10
Bus Power (mA): 250
Speed: Up to 12 Mb/sec
Manufacturer: Mitsumi Electric
Product ID: 0x020b
Vendor ID: 0x05ac (Apple Computer, Inc.)
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBOHCI
PCI Device ID: 0x0035
PCI Revision ID: 0x0043
PCI Vendor ID: 0x1033
Bus Number: 0x0b
hp LaserJet 1012:
Version: 1.00
Bus Power (mA): 500
Speed: Up to 12 Mb/sec
Manufacturer: Hewlett-Packard
Product ID: 0x0d17
Serial Number: 00CNFB638356
Vendor ID: 0x03f0
hp LaserJet 1012:
Version: 1.00
Bus Power (mA): 500
Speed: Up to 12 Mb/sec
Manufacturer: Hewlett-Packard
Product ID: 0x0d17
Serial Number: 00CNFB638356
Vendor ID: 0x03f0
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBOHCI
PCI Device ID: 0x0040
PCI Revision ID: 0x0001
PCI Vendor ID: 0x106b
Bus Number: 0x09
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBOHCI
PCI Device ID: 0x0040
PCI Revision ID: 0x0001
PCI Vendor ID: 0x106b
Bus Number: 0x08
USB High-Speed Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBEHCI
PCI Device ID: 0x00e0
PCI Revision ID: 0x0004
PCI Vendor ID: 0x1033
Bus Number: 0x4bSORRY, BUT MY PREVIOUS POSTING DIDN'T HAVE THE FULL LIST OF HARDWARE CONTENTS of my Power Mac G5.
Hello Final Cut Studio 2 Experts,
I'm considering purchasing Final Cut Studi 2, and to make sure that I'll benefit from the full range of specific application (FCS/motion/color...) and I'd like to ask few questions (5 main points) regarding requirements and recommendations. So, please be prepared for much reading as I am not an expert on the matter. I like to know if my computer accepts any further hardware parts highly recommended and if I can purchase and install them myself. And yes, you should also know that I intend to use a Panasonic multi-format (HD/SD) camera for capturing and exporting videos.
N.B. Please note that the full list of my Hardware contents appear at the bottom of this text.
THANKS IN ADVANCE for your expert advise!
So, here we go:
Application-Specific Requirements
Final Cut Studio
Capturing HD resolution video using the ProRes 422 format requires a Mac Pro with an Intel Xeon processor or a G5 Quad computer and a qualified third-party capture card.
1) Do I need an Intel Xeon processor? If yes, can I purchase and install the component by myself (like RAM)?
Motion
The standard graphics card in any Mac Pro, MacBook Pro, iMac with Intel Core Duo, Power Mac G5, or iMac G5; 1.25GHz or faster PowerBook G4; or 1.25GHz or faster flat-panel iMac:
ATI Radeon 9800, 9700 Pro, 9600 XT, or 9600 Pro
ATI Mobility Radeon 9700 or 9600
NVIDIA GeForce 7600 GT, 7300 GT, 6600, 6600 LE, FX Go5200, or FX 5200 Ultra
For 16- and 32-bit rendering: a graphics card with at least 128MB of VRAM
2) Do I need one of the ATI Radeon 9800, 9700... or ATI Mobility Radeon? Why does my Hardware contents say ATI Radeon 9600, and not ATI Mobility Radeon 9600, is there a difference?
Color
The standard graphics card in any Mac Pro, 17-inch MacBook Pro, 24-inch iMac with Intel Core Duo, or 2.5GHz or faster Power Mac G5 Quad:
ATI Mobility Radeon X1600
ATI Radeon X1600
NVIDIA GeForce 7800 GT, 7600 GT, 7300 GT, 6600, or Quadro FX 4500
A display with 1680-by-1050 resolution or higher
A three-button mouse for full functionality
3) Do I need and ATI Mobility Radeon X1600 or ATI Radeon X1600?
DVD Studio Pro
For playback of DVD Studio Pro 4-authored HD DVDs: a Macintosh computer with a PowerPC G5 or Intel Core Duo processor
For writing finished projects to disc: an Apple SuperDrive or other DVD recorder
For writing finished projects to a double-layer disc: a double-layer-compatible recorder and double-layer media
For transporting HD projects to a replicator: an external drive or Internet transfer of the project’s disk image
For transporting SD projects that contain copy-protection or dual-layer features to a replicator: a DLT drive, external drive, or Internet transfer of the project’s disk image
4) Do I have an Intel Core Duo processor? Do I need an Apple SuperDrive?
What is a "replicator"?
Application-Specific Recommendations
Motion
One of the following graphics cards is highly recommended:
ATI Radeon X1900 XT, X850 XT, X800 XT, or X1600
NVIDIA GeForce 7800 GT, 6800 Ultra DDL, 6800 GT DDL, or Quadro FX 4500
For 32-bit rendering: a graphics card with 256MB of VRAM or more
Color
The following graphics card is highly recommended:
ATI Radeon X1900 XT
Dual displays with 1920-by-1200 or higher resolution
5) Do I have one of the highly recommended cards ATI Radeon X1900 XT etc...? How do I get it and can I install it myself?
My Power Mac G5 HARDWARE CONTENTS:
Hardware Overview:
Machine Name: Power Mac G5
Machine Model: PowerMac7,3
CPU Type: PowerPC G5 (3.0)
Number Of CPUs: 2
CPU Speed: 2.3 GHz
L2 Cache (per CPU): 512 KB
Memory: 4.5 GB
Bus Speed: 1.15 GHz
Boot ROM Version: 5.2.4f1
Serial Number: G85167AGRU3
ATA Bus:
SONY DVD RW DW-Q28A:
Model: SONY DVD RW DW-Q28A
Revision: KAS7
Serial Number:
Detachable Drive: No
Protocol: ATAPI
Unit Number: 0
Socket Type: Internal
SONY DVD RW DW-Q28A:
Model: SONY DVD RW DW-Q28A
Revision: KAS7
Serial Number:
Detachable Drive: No
Protocol: ATAPI
Unit Number: 0
Socket Type: Internal
Built In Sound Card:
Devices:
Texas Instruments TAS3004:
Inputs and Outputs:
Line Level Input:
Controls: Left, Right
Playthrough: No
PluginID: TAS
Headphones:
Controls: Mute, Left, Right
PluginID: TAS
Internal Speakers:
Controls: Mute, Master
PluginID: TAS
Line Level Output:
Controls: Mute, Left, Right
PluginID: TAS
Crystal Semiconductor CS84xx:
Inputs and Outputs:
S/PDIF Digital Input:
Controls: Mute
Playthrough: No
PluginID: Topaz
S/PDIF Digital Output:
Controls: Mute
PluginID: Topaz
Formats:
PCM 16:
Bit Depth: 16
Bit Width: 16
Channels: 2
Mixable: Yes
Sample Rates: 32 KHz, 44.1 KHz, 48 KHz
PCM 24:
Bit Depth: 24
Bit Width: 32
Channels: 2
Mixable: Yes
Sample Rates: 32 KHz, 44.1 KHz, 48 KHz
AC3 16:
Bit Depth: 16
Bit Width: 16
Channels: 2
Mixable: No
Sample Rates: 32 KHz, 44.1 KHz, 48 KHz
Bluetooth: No Information Found.
SONY DVD RW DW-Q28A:
Firmware Revision: KAS7
Interconnect: ATAPI
Burn Support: Yes (Apple Shipped/Supported)
Cache: 2048 KB
Reads DVD: Yes
CD-Write: -R, -RW
DVD-Write: -R, -RW, +R, +RW, +R DL
Burn Underrun Protection CD: Yes
Burn Underrun Protection DVD: Yes
Write Strategies: CD-TAO, CD-SAO, CD-Raw, DVD-DAO
Media: No
Fibre Channel: No Information Found.
FireWire Bus:
Maximum Speed: Up to 800 Mb/sec
ATI Radeon 9600:
Chipset Model: ATY,RV351
Type: Display
Bus: AGP
Slot: SLOT-1
VRAM (Total): 128 MB
Vendor: ATI (0x1002)
Device ID: 0x4150
Revision ID: 0x0000
ROM Revision: 113-A58504-113
Displays:
Cinema HD Display:
Display Type: LCD
Resolution: 1920 x 1200
Depth: 32-bit Color
Core Image: Supported
Main Display: Yes
Mirror: Off
Online: Yes
Quartz Extreme: Supported
Rotation: Supported
Display:
Status: No display connected
DIMM0/J11:
Size: 256 MB
Type: DDR SDRAM
Speed: PC3200U-30330
Status: OK
DIMM1/J12:
Size: 256 MB
Type: DDR SDRAM
Speed: PC3200U-30330
Status: OK
DIMM2/J13:
Size: 1 GB
Type: DDR SDRAM
Speed: PC3200U-30330
Status: OK
DIMM3/J14:
Size: 1 GB
Type: DDR SDRAM
Speed: PC3200U-30330
Status: OK
DIMM4/J41:
Size: 1 GB
Type: DDR SDRAM
Speed: PC3200U-30330
Status: OK
DIMM5/J42:
Size: 1 GB
Type: DDR SDRAM
Speed: PC3200U-30330
Status: OK
DIMM6/J43:
Size: Empty
Type: Empty
Speed: Empty
Status: Empty
DIMM7/J44:
Size: Empty
Type: Empty
Speed: Empty
Status: Empty
PC Cards: No Information Found.
PCI Cards: No Information Found.
Parallel SCSI: No Information Found.
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 0
Display Sleep Timer (Minutes): 0
Dynamic Power Step: No
Reduce Processor Speed: No
Sleep On Power Button: Yes
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On LAN: No
Wake On Modem Ring: No
Adobe PDF 7.0:
Status: Idle
Print Server: Local
Driver Version: 10.4
Default: No
URI: pdf700://distiller/
PPD: Adobe PDF 3016.102
PPD File Version: 1.0
PostScript Version: (3016.102) 0
hp LaserJet 1012:
Status: Idle
Print Server: Local
Driver Version: 1.4.5
Default: Yes
URI: usb://Hewlett-Packard/hp LaserJet 1012?serial=00CNFB638356
PPD: hp LaserJet 1012
PPD File Version: 1.0
PostScript Version: (3011.104) 0
Serial-ATA Bus:
Maxtor 6B250S0:
Capacity: 233.76 GB
Model: Maxtor 6B250S0
Revision: BANC1E50
Serial Number: B61QB0RH
Removable Media: No
Detachable Drive: No
BSD Name: disk1
Protocol: ata
Unit Number: 0
Socket Type: Serial-ATA
Bay Name: "A (upper)"
OS9 Drivers: No
S.M.A.R.T. status: Verified
Volumes:
Macintosh HD:
Capacity: 233.64 GB
Available: 50.02 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk1s3
Mount Point: /
Maxtor 6B250S0:
Capacity: 233.76 GB
Model: Maxtor 6B250S0
Revision: BANC1E50
Serial Number: B61QB0RH
Removable Media: No
Detachable Drive: No
BSD Name: disk1
Protocol: ata
Unit Number: 0
Socket Type: Serial-ATA
Bay Name: "A (upper)"
OS9 Drivers: No
S.M.A.R.T. status: Verified
Volumes:
Macintosh HD:
Capacity: 233.64 GB
Available: 50.02 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk1s3
Mount Point: /
Serial-ATA Bus:
Maxtor 7L300S0:
Capacity: 279.48 GB
Model: Maxtor 7L300S0
Revision: BANC1E00
Serial Number: L602X73H
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Protocol: ata
Unit Number: 0
Socket Type: Serial-ATA
Bay Name: "B (lower)"
OS9 Drivers: No
S.M.A.R.T. status: Verified
Volumes:
Primo Volume:
Capacity: 279.36 GB
Available: 154.23 GB
Writable: Yes
File System: HFS+
BSD Name: disk0s3
Mount Point: /Volumes/Primo Volume
Maxtor 7L300S0:
Capacity: 279.48 GB
Model: Maxtor 7L300S0
Revision: BANC1E00
Serial Number: L602X73H
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Protocol: ata
Unit Number: 0
Socket Type: Serial-ATA
Bay Name: "B (lower)"
OS9 Drivers: No
S.M.A.R.T. status: Verified
Volumes:
Primo Volume:
Capacity: 279.36 GB
Available: 154.23 GB
Writable: Yes
File System: HFS+
BSD Name: disk0s3
Mount Point: /Volumes/Primo Volume
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBOHCI
PCI Device ID: 0x0035
PCI Revision ID: 0x0043
PCI Vendor ID: 0x1033
Bus Number: 0x2b
Hub in Apple Pro Keyboard:
Version: 4.10
Bus Power (mA): 500
Speed: Up to 12 Mb/sec
Manufacturer: Mitsumi Electric
Product ID: 0x1003
Vendor ID: 0x05ac (Apple Computer, Inc.)
Apple Optical USB Mouse:
Version: 3.40
Bus Power (mA): 100
Speed: Up to 1.5 Mb/sec
Manufacturer: Logitech
Product ID: 0x0307
Vendor ID: 0x05ac (Apple Computer, Inc.)
Apple Pro Keyboard:
Version: 4.10
Bus Power (mA): 250
Speed: Up to 12 Mb/sec
Manufacturer: Mitsumi Electric
Product ID: 0x020b
Vendor ID: 0x05ac (Apple Computer, Inc.)
Hub in Apple Pro Keyboard:
Version: 4.10
Bus Power (mA): 500
Speed: Up to 12 Mb/sec
Manufacturer: Mitsumi Electric
Product ID: 0x1003
Vendor ID: 0x05ac (Apple Computer, Inc.)
Apple Optical USB Mouse:
Version: 3.40
Bus Power (mA): 100
Speed: Up to 1.5 Mb/sec
Manufacturer: Logitech
Product ID: 0x0307
Vendor ID: 0x05ac (Apple Computer, Inc.)
Apple Pro Keyboard:
Version: 4.10
Bus Power (mA): 250
Speed: Up to 12 Mb/sec
Manufacturer: Mitsumi Electric
Product ID: 0x020b
Vendor ID: 0x05ac (Apple Computer, Inc.)
Apple Optical USB Mouse:
Version: 3.40
Bus Power (mA): 100
Speed: Up to 1.5 Mb/sec
Manufacturer: Logitech
Product ID: 0x0307
Vendor ID: 0x05ac (Apple Computer, Inc.)
Apple Pro Keyboard:
Version: 4.10
Bus Power (mA): 250
Speed: Up to 12 Mb/sec
Manufacturer: Mitsumi Electric
Product ID: 0x020b
Vendor ID: 0x05ac (Apple Computer, Inc.)
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBOHCI
PCI Device ID: 0x0035
PCI Revision ID: 0x0043
PCI Vendor ID: 0x1033
Bus Number: 0x0b
hp LaserJet 1012:
Version: 1.00
Bus Power (mA): 500
Speed: Up to 12 Mb/sec
Manufacturer: Hewlett-Packard
Product ID: 0x0d17
Serial Number: 00CNFB638356
Vendor ID: 0x03f0
hp LaserJet 1012:
Version: 1.00
Bus Power (mA): 500
Speed: Up to 12 Mb/sec
Manufacturer: Hewlett-Packard
Product ID: 0x0d17
Serial Number: 00CNFB638356
Vendor ID: 0x03f0
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBOHCI
PCI Device ID: 0x0040
PCI Revision ID: 0x0001
PCI Vendor ID: 0x106b
Bus Number: 0x09
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBOHCI
PCI Device ID: 0x0040
PCI Revision ID: 0x0001
PCI Vendor ID: 0x106b
Bus Number: 0x08
USB High-Speed Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBEHCI
PCI Device ID: 0x00e0
PCI Revision ID: 0x0004
PCI Vendor ID: 0x1033
Bus Number: 0x4b
Message was edited by: Rinaldo -
The difference between Final Cut Pro and Final Cut Studio 2
I'm looking at buying FCP. Can I buy Final Cut Studio 2 to get FCP or is that only a Upgrade and where would i buy it. How do I go about buying FCP and how much is it
Final Cut Pro v6 is only available as a component within Final Cut Studio 2.
What it is, what is included and how to purchase it is spelled out here:
http://store.apple.com/us/product/MA886Z/A?mco=MTIxODk3Mw
x -
Wont let me open final cut studio-missing hardware
when i try to open final cut studio a message comes up saying missing hardware 512mb ram, but i have this on my computer.
do i need more ram?
what will make it work?
any help would be greatfully appreciatedWelcome to the forums.
Yes, you need more RAM. FCP needs MINIMUM 512 MB Ram, and your system right now is taking up half of what you have. 1.5GB is the min RAM I recommend for running FCP. 2.5GB to be comfortable...3.5GB to be stylin'.
Shane -
Why Can't I Install Final Cut Studio?
I have a MacBook Pro which is about 12 months old. It has a 2.66GHz Intel Core i7 Processor and 8G of RAM. I have been trying to install Final Cut Studio 5.1. Yeah I know that is an OLLLLLLLLLLLD version. Why I chose not to update is neither here nor there. I was about to update when Final Cut Pro X was realeaded and FCS vanished into the ether. I really only wanted DVD Pro but when that wouldn't install I went back to Square 1.
The specificationa as stated are:- "These discs contain the files required to install Final Cut Studio 5.1 on either PPC or Intel based Mac computers."
The error message that shows up on the screen when I click on the install package is:- "You can't open the application Final Cut Studio pro.mpkg because Power PC applucations are no longer supported."
This is despite the stated specifications and the fact that there is a Universal Icon on the discs.
I am also having a simillar but not the same problem with iLife '06 but i'll start another thread on that.
I'm confused, thanks for your help in advance.Your problem is you are running Lion as your OS (10.7) and Lion does not support Rosetta which is required to run the INSTALLER of FCS 2. If you were running Snow Leopard, you would have been able to do the install.
MtD -
Final Cut Studio license invalid after upgrading to Leopard?
Hello,
After upgrading to Leopard 10.5.1, Final Cut Studio v5.1.4 and its companion apps like DVD Studio 4 do not recognize my FC Studio License as valid. I input the license key and it says:
"Licensing Error
This application cannot continue because the licensing data is corrupt."
I am a licensed user via the FC Studio Crossgrade since 2006 and all has been fine with Tiger before Leopard.
I have used Disk Utility to "repair permissions". I have removed the FC files from the Preferences folder to give it a clean start.
PERHAPS A HINT?:
So I tried to re-install FC Studio 5.1 from the FC Install DVD and I get this message after inputting the key:
"Alert
Licensing Error: The license file will not be written to disk because the user does not have enough privileges."
I have Administrator privileges on this account and I even tried to install it as 'root' and the same error occurs.
Is there a file that I need to change permissions on?
THANKS for any help here! And happy holidays.
BonafideHi,
Unfortunately there is also an issue with installing FCS2 on a brand new installation with Leopard and this licensing error.
"Alert Licensing Error: The license file will not be written to disk because the user does not have enough privileges."
This also occurs, apparently, that if you are logged in with an Active Directory user with Admin privileges it still will not let you install the product keys.
This is much the same as a problem with Adobe CS3 products, only the updates work when you are logged in with a local admin - not an Active Directory Admin.
Both these problems are really really annoying for those on corporate networks - such as myself.
For my problem, I had to log out as my AD account, login as a local admin and then install the software. .
KJ -
Against my better judgement (now that Apple has turned into Microsoft 10 years ago, breaking apps with every OS update, followed by radio silence from Apple, pretending like they didn't do anything), I just upgraded from Mountain Lion to Yosemite and noticed that my Motion 4 icon is now greyed out. Thanks Apple.
I still do the majority of my work in Final Cut Pro 7, with many, many, Motion 4 projects embedded in the timeline (so that I can change them in Motion and have them seamlessly updated in my Final Cut Pro project), including an unfinished feature length documentary on gay and lesbian history from 2000 BC until 1900 AD. Should I just throw the entire film into the rubbish bin? I would presume that Motion 5.1.2 is incompatible with Final Cut 7? So what am I supposed to do now?
1 - Downgrade to Mountain Lion (or heck, why not Snow Leopard?)?
2 - Switch to Adobe Premiere?
3 - All of the above?
Thanks (for nothing, Apple).
MacBook Pro 15" with Retina Display
2.4 GHz Intel Core i7
8 GB 1600 MHz DDR3
NVIDIA GeForce GT 650M 1024 MBAfter some peacefull time my system crashed completely on Friday!
I installed all from Scratch to make sure its not some old stuff that I carried on during migration.
It's not a problem with the motion files as I deleted all of them and XML export is still crashing!
The situation is, that after installing it all I got the same quicktime translation error again and I am quite angry about how Apple handles clients who are working on projects with the recent FCP story.
Unfortunately due to the problems in exporting XML I am not even able to switch to Adobe Premier as this is the only way to import there.
After a lot of testing I am quite sure, that this issue has to do something with an Apple Update release between June 2011 and now.
Conclusion: Final Cut Studio II is not working correctly anymore as it did before June 2011!!! Apple, Please fix this issue asap.!!!! -
How can I install Final Cut Studio 2 on my new MacBook Pro with Lion?
I just purchased and received a new 15" MacBook Pro (non-retina) last week. I need to install Final Cut Studio 2 on this computer. I have researched this and found that I need to install Rosetta from the Snow Leopard DVD in order to do this. This is the first Mac I've bought ( although I've been working with them for years), so I don't have a Snow Leopard DVD. I am a high school teacher and we use FCS 2 for my classes so buying FCP X is not a viable option for me since I teach FCP 6. The iMacs we use in school run Leopard and were never upgraded to Snow Leopard (budget cuts and all), so I can't even borrow one from my district.
Does anyone know how I can obtain Rosetta? Or another way to install this without it?
Thank you ! :)There is no way to add Rosetta support because it is not supported by OS X Lion at system level. This has been documented before the release of OS X Lion by itself.
If you really need Final Cut Studio 2, I would return your computer if possible, and purchase a Mac that is capable of running Snow Leopard (all 2010 models, early 2011 MBP and some other 2011 models) -
How many computers can I install Final Cut Studio 2 on?
Here's my dilemma. I'm a poor soon-to-be college grad with an old 2004 PowerBook G4. I'm starting to do video projects this summer and want to get a new computer and Final Cut Studio 2. The problem is, I don't have money for both. However, my current computer DOES meet the requirements (1GB RAM, 1.5Ghz engine, and 17" monitor) to install the apps and run them. So, ideally, I would buy Final Cut Studio 2 and install it on this old computer until I saved up enough money to get myself a Mac Book Pro in a few months. Then, I would install FCS 2 on my new computer. Is this possible? Can I install FCS 2 on my old G4 and then months later when I get a new computer, on my new computer? Or at least transfer the apps to my new computer?
Thanks ahead of time! I haven't gone computer shopping in a while so I don't remember how this all works!
Message was edited by: SeefInstall it on the PowerBook, and when you get the MacBook Pro, download and use this tool on the PowerBook prior to installing it on the MacBook Pro. The license for Final Cut Studio 2 permits it to be installed on a desktop and portable but not two portables.
If you're in the middle of a project when you get the MacBook Pro, complete it before changing the configuration.
(43392) -
General Overview on How to use Final Cut Studio to create a Blu-Ray DVD
I am a new user of Final Cut Studio and need an experienced user to give my a progression guide on how to create a Blu-Ray DVD of my recent Alaska Trip. Last month I spend 8 days in Alaska visiting Denali and Juneau primarily. During that time I took about 100 short video clips (HD 1080p) and 570+ still photos with my Canon 7D. I have experimented with some pieces of the software and have created a Blu-Ray disk using Final Cut Pro and Compressor. However my goal is to create this DVD with menus that will play short clips (some narrated) and still photos(also some narration). I did a short one in DVD Studio Pro this morning but need some general guidance on what progression and programs to use to create this project. I was not able to take my video from the Studio Pro Sequence I created for my 1st DVD I had to take the original clips which were processed using Apple ProRes 422 and copy them in one at a time and then find the audio (on the voice overs) I created and also place them into DVD Studio Pro one at a time. I obviously need some guidance on the proper progression.
Any help would be greatly appreciated.Here's the situation...
DVD Studio Pro will not do the trick for you - it doesn't do blu-ray discs. If you want to do Blu-ray you've got to use either Final Cut Pro's "Export" command or Compressor's "Burn Blu-ray disc" template. The downside to both of these approaches is that you can't burn more than one title (or movie, etc.) using Final Cut Studio.
To do what you want to do, you need Toast (at least). Toast will auto-generate menus but will let you put more than one title per slide (so you can put multiple slideshows on the same disc).
If you want to do full-on customizing of menus and multi-level menus, for that you need Adobe's Encore.
My suggestion - Get Toast. Encore is close to $800.
Here's your progression (at least the one I use).
Edit in Final Cut Pro (ProRes 422 is fine, ProRes 422 LT would do the trick as well)
Export as QuickTime movies (original settings)
In Compressor using the H.264 for Blu-ray setting and Dolby Digital setting and create elementary streams for video (.264 file) and audio (.ac3). Make sure these files have identical names except for the extension.
Using toast, add the video file to the Toast project and it'll find the audio file.
Burn away! -
Is it unlawful to sell my used final cut studio version 3 software?
I had listed my software at eBay after deauthorizing it from my Mac Pro. Was I under a contract with Apple that prevented me from reselling the software?(I'm afraid I don't have time to read pages of fine print.) Here's the message I just received from eBay after the closed my auction:
You recently listed the following listing:
300791938347 - Apple Final Cut Studio Version 3 (Version 2 Retail plus Version 3 Upgrade)
Your listing has been removed.
Your item was removed because of a request we received from BSA (Business Software Alliance) (US), a member of our Verified Rights Owner Program (VeRO), asking us to remove the item for:
- Software offered for sale is in violation of an enforceable license agreement, which constitutes a copyright infringement.
If you have additional questions or concerns on why your item was removed, please contact BSA (Business Software Alliance) (US) directly at:
[email protected]
Please allow 7 days for BSA (Business Software Alliance) (US) to reply to you.
All listing fees associated with the removed item(s) have been credited back to your account.
The rights owner or an agent authorized to act on behalf of the rights owner, BSA (Business Software Alliance) (US), notified eBay that this listing violates intellectual property rights. When eBay receives a report of this type of violation, we remove the listing to comply with the law.
Copyright infringement is unlawful and against eBay policies. Copyright is the protection provided by law to the authors of creative works, such as movies, music, software, photographs, and books, both published and unpublished. Copyright owners have the exclusive right to reproduce the copyrighted work, to distribute copies of the copyrighted work, and to perform or display the copyrighted work publicly.
eBay doesn't allow the listing of unauthorized copies of copyrighted works. Unauthorized copies include backup, pirated, duplicated, or bootlegged copies.
If the product you are selling is a copy of another work that you aren't authorized to copy, don't list the item. eBay doesn't allow the sale of software if this violates the manufacturer's copyright license. Some common types of software with license agreement restrictions include:
-- Academic software: Software that is sold at discounted prices to students, faculty members, and educational institutions
-- Beta software: Early copies of software that are distributed by software developers for evaluation, testing, and troubleshooting purposes
-- Original Equipment Manufacturer (OEM) software: Software that is included with the purchase of new equipment such as a computer, digital camera, or printer
You may need to obtain the manufacturer's consent to sell this software.
For more information, please visit:
http://pages.ebay.com/help/policies/replica-counterfeit.html
You may need to take a tutorial. The next time you sell, you may be asked to take the tutorial, if it's required. Once you've completed the tutorial successfully, please review your account status for any other possible concerns. If there are no other issues, you should be able to sell again.
To take the intellectual property tutorial, please visit:
http://pages.ebay.com/help/tutorial/verotutorial/intro.html
Please be aware that any additional violations of this policy may result in the suspension of your account. eBay understands that you may be concerned about this situation. We encourage you to contact BSA (Business Software Alliance) (US) directly if you have any questions.
You can send an email to: [email protected]
For more information on how eBay protects Intellectual Property, or for additional information if you believe that your listing has been removed as a result of an error or misidentification, please visit the following Help page:
http://pages.ebay.com/help/policies/programs-vero-ov.html
For more information on why eBay may remove a listing, please visit:
http://pages.ebay.com/help/sell/questions/listing-ended.html
Please be assured that your listings have not been targeted in any way. Although there may be similar items currently listed on eBay, we review all listings that are reported to us by eBay members or Verified Rights Owner (VeRO) program participants. We rely on reports from our members to help maintain the safety and security of our Community. We encourage you to report any items by using the REPORT THIS ITEM button on the listing so we can quickly remove any other items that should be removed.
If you have additional questions, contact our policy experts. Get started by clicking the link below:
http://contact.ebay.com/ws/eBayISAPI.dll?ContactCS&Query=1337&Domain=Homer_EOA&F rom=5265
We appreciate your understanding.
Thanks,
eBay
Please don't reply to this message. It was sent from an address that doesn't accept incoming email.
H5265eBay heavily "overprotects" copyright owners.
The BSA is hired by Apple to look out for copyright violations. They simply go after everything without any investigation. eBay plays along and so you are the one with the problem to do something completely lega.
Here is the relevant section of FCS's SLA:
3. Transfer. You may not rent, lease, lend, sell, redistribute or sublicense the Apple Software. You may, however, make a one-time permanent transfer of all of your license rights to the Apple Software to another party, provided that: (a) the transfer must include all of the Apple Software, including all its component parts, original media, printed materials and this License; (b) you do not retain any copies of the Apple Software, full or partial, including copies stored on a computer or other storage device; and (c) the party receiving the Apple Software reads and agrees to accept the terms and conditions of this License. All components of the Apple Software are provided as part of a bundle and may not be separated from the bundle and distributed as standalone applications.
This means that you are allowed to sell the package if you are the original owner of the software. -
Final Cut Studio is crashing a lot using a Mac Pro (nehalem) 2009
Greetings,
I have a video workstation based on a Mac Pro (2x2.26GHz Quad-Core Intel Xeon Nehalem, 6 GB RAM, 640 GB HD, 512 NVIDEA VRAM) with a Blackmagic Decklink HD Extreme 2009 and an Highpoint RocketRAID 4322 card (properly connected to a RAID 5 array).
I'm editing, with Final Cut Studio 3, a big TV project with some TGA and loads of HD XDCAM EX 35mbs video footage.
*What is happening wrong?*
Final Cut Pro is crashing to many times and dont let me work with the flow that is supposed. I start to work and i do a bit of scrubbing in the timeline and suddenly the rainbow spyral starts to spin and kaput! FCP just crashes.
I've tried to many things. Re-installing everything from the baseline, plug out the 2 PCIe cards (and not even the drivers are installed). Even so FCP still crashes with the project.
Funny thing is... This symptom only happens with the Nehalem Mac Pro. I have another station based on a Mac Pro 2x2.66 GHz Dual Core Xeon 3 GB RAM 2006 and when i run the project... everything works fine. FCP here doesn't crash.
This is what makes me believe that the problem must be with the new Mac Pro.
I have the reports generated by the FCP after the crash. You can find it here:
http://www.ideiascompernas.com/reports/
I'm getting frustrated because i've invested big in this workstation, safe in the knowledge that it was going to be stable to complete my requirements.
Is there anything that i or Apple can do to resolve my problem. Is it the processor? Extended Hardware Test says that everything is ok.
I'll be waiting,
best regards, thanks,
PedroYou may want to also post here:
Final Cut Studio forum:
http://discussions.apple.com/category.jspa?categoryID=123
Content creation with Final Cut Studio
http://discussions.apple.com/forum.jspa?forumID=1137
I see you have the GT120, not a very nice card really but maybe it is 'enough.' I'd upgrade. To ATI Radeon 4870, once you get it stable and working.
http://discussions.apple.com/thread.jspa?messageID=10251193&tstart=0
I see your crash is kernel panic actually.
Exception Type: EXCBADACCESS (SIGBUS)
Exception Codes: KERNPROTECTIONFAILURE at 0x0000000000000000
Crashed Thread: 194
Almost always that is memory related, are you seeing parity errors?
Watch System Profile - Memory tab
Replace the RAM (I'd even up it to more memory, 6 x 2GB is what I would have configured for)
Have you tested your RAM? run Apple Hardware Test?
Disabled ALL USB and Firewire devices?
Is the RR4322 okay to run in slot #2 (16x) rather than in slot 3 or 4 (4x)?
Getting RAM replaced, advanced exchange, or go out and getting some Kingston or Crucial etc for your system, and swapping, really is one good method, trial and error, to find the cultprit or rule out RAM.
Errors like this can mean flushing your caches is a must, and possibly due to errors and crashes, clean system install, checking data (both time consuming) and being careful to recheck your drives with Disk Warrior and/or TechTool Pro 5 to insure there are not any corrupt files (not perfect either which is why restore the system from known good backup image can be a must). -
Final cut Studio 2 - how much a no-go with logic 9?
I have the new Logic 9 upgrade but I see in the installation notes that the new compressor 3.5 and Soundtrack Pro 3 Is "incompatible" with Final cut studio 2.
Now I also run Finalcut studio 2 apps regularly but I hadn't planned on upgrading just yet but I certainly want to see soundtrack pro 3 (so many bugs in v2!!).
Does anyone know what will happen if I install STP and compressor from logic 9 regardless? How incompatible is incompatible?My experience with logic9 and FCS 2...
I've installed the full package of Logic 9 regardless of the incompatibility problems (yes, brave, I know:-)
You are indeed "allowed" to do this - you just click a sort of "do it anyway" button.
So far I have launched existing projects and done basic edit cuts in FCP with no problems. I've edited for a day so I feel happy to conclude that basic editing in FCP is not broken.
I have exported ref. and self-contained movies via quicktime conversion so thats not broken.
I have exported XML files from FCP to Logic 9, thats not broken.
Soundtrack v3 launches, plays audio and appears to be ok after about 15mins of me testing - by no means conclusive testing.
I've used logic for a day and it seems just dandy.
I have not used colour, compressor or motion.
Just thought I'd mention it in case anyone else is facing the same dilemma as I was. -
How to get final cut studio 2 install disk to work on macbook air OS 10.8.4
I just purchased a Macbook Air OSX Mountain Lion 10.8.4 and trying to install Final Cut Studio 2, however the install disk wont open using a superdrive. How can I get my software loaded?
Thank you.Try this forum:
https://discussions.apple.com/community/professional_applications/final_cut_stud io
Al
Maybe you are looking for
-
How to read the data in a field that has data type as VARILRAW
Hello friends I have created a table with one of the field to accept a huge variable lenght field of type 'VARILRAW'. I have written a short Function to accept the data from an external program. Is there a way to see the data that Ihave entered in th
-
Clarification on purchase invoice (F-43) via APP
Dear All, Need clarification on clearing purchase invoice (F-43) via APP. I have post two purchase invoice (F-43) one is by updating payment terms and with out updating payment terms,while doing APP i was not able to view invoice which i have process
-
Bug in JDev 9.0.3.3 when removing joined entities from a view
Hi, I observed in JDev 9.0.3.3 the following behavior for views containing several joined entities: -I'm creating the view V1 based on the entity E1 and generate the row implementation java file with accessors (close wizard) -I'm joining a
-
Mail archive taking up 200+ Gigs!!!
Hi, I use IMAP, and therefore delete the emails a do not want at all and just keep the rest of them on the server. I recently noticed that I was running out of space on my computer and that MAC mail was using 200+ Gigs of space (Yes I have a lot of m
-
I have a movie I've created in iMovie (5) on one of my PowerBooks. I transferred it to my PowerMac a few months ago and when I played it back it was choppy and the audio was bad. I thought it was because my 60G hard drive was almost full. So I recent