ARD not recognizing client machine.

Installed Client 3.5.1 on MacBook running Snow Leopard but ARD still tells me the software on the client is not up to date. It recognizes the IP address but does not "fill-in-the-blanks" such as DNS Name, ARD version and MacOS Version in the Get Info Window as it does in all the other machines. I desperately need this to work. It was actually working with this computer until I installed the update 3.5.1 Administrator on my admin Machine.

Have you tried removing the Macbook from your All Computers list and then re-adding it?

Similar Messages

ARD not recognizing client computers

Hello, I recently purchased ARD 2.2 and have been trying to observe and control my friends powerbook G4 and my dads ibook G4. They both turned on the ARD client in the Sharing pane in system preferences and checked their username and all the neccessary options in the access privileges window, but when I type in their ip addresses (that were found in the Network system preferences pane) ARD comes up with a dimmed gray computer icon and shows no information about those computers (except for the ip address that I entered). When I enter their correct username and password, ARD says that the verification failed. Although, when my friend with the Powerbook G4 came over to my house, and used the same internet as me, I could easily control and observe his computer, after entering his username and password, using the local network scanner.
Could Someone Please Help Me?
William Dunn

William has posted what will probably be the best compendium of information, though of course the manual that came (or should have come ) with the Linksys will also be of help.
Note that you have to have those ports open on both ends, your Internet connection and at your friend's and your dad's, if (as would seem likely) the systems you're trying to connect are in different locations from yours.

Finder not recognizing "Time Machine" partition of my external HD.

My Seagate 2TB External HD (the one that says it works especially for Mac Time Machine!) is partitioned in 2 - half for my music and other half for Time Machine. Finder is now only recognizing the "music" partition and will not run Time Machine. I noticed this evening it hasn't run TM in a week. I barely even use my computer, though it is basicallly on all the time. I have a 2012 MacBook Air running OSX 10.9.2. Help!!

Or do I just need to get a 2nd external HD with less memory and dedicate it to Time Machine?
Well, OP is considering this option, and it one way to go TM-dedicated TM external. Really their options depend on how much free space is present on their Mac internal and current external. Disk Utility erase/ partition options will reformat, quite obviously, but even if they have just one external available it is usually possible to backup video and other stored files to say DVD media while they reorganize/ reformat their backup drive.
Another choice is to turn TM off.
Due to the magic of shareware there are now third-party utilities that allow you to alter the frequency of Time Machine Back up.
http://www.klieme.com/TimeMachineScheduler.html

ARD not recognizing disk image

I used Network Disk Utility to make an image of my powerbook to set up clients. When I try to set the startup disk to the image it always fails. The image does not appear in the list. So I tried to set it to a special volume but to no avail. I have searched the manual and website for the correct procedure. All I find is "set the client's startup disk to [point to the image." How do I do this? I am a new user of ARD and deperately need help.

First, am I correct in presuming that you have a Mac OS X Server set up with NetBoot running and your image enabled? If not, that's your problem. You can only boot a workstation to a disk image served by NetBoot.
If you do have this set up, can you successfully boot from the image when you're sitting at a workstation (i.e. not setting it through ARD)?

Mac not recognizing Time Machine after Mavericks Clean Install

Hello,
I just did a clean install of OSX Mavericks and I can't access any of my Time Machine backups and am very worried about having lost all my data.
Before I did the clean install, I backed up data using my Toshiba 1TB External hard drive using Time Machine. It backed up successfully and has been doing so for about a year.
After the successful clean install of Mavericks, I plugged my external hard drive in, to which I was prompted with "would you like to use this hard drive for Time Machine Backups?" I clicked yes, and it said "Decrypting Time Machine Backups." I got worried and quickly cancelled the decryption process.
Now, whenever I plug in the external hard drive, nothing comes up. I can't access any of its files. Whenever I open the Disk Utility application, it does recognize that its plugged in, but its grayed out, and I can't do anything with the drive.
I'm very worried about losing all my data and info and would greatly appreciate any insight about this.
Thanks
MacBook Pro
15inch Late 2011
OSX 10.9.1

Solved. Right click on the hard drive in Disk Utility, click "unlock."
So simple, yet so obscure.

SCCM not recognizing client is installed

I have a windows server 2008r2 that stopped receiving updates so I re-installed the client. I deleted from the collection and let discovery pick it back up, only now it shows that there is no client installed on it, so I can't approve it.
How can I get SCCM to recognize that it does have the client? It appears the client is working fine.

Run the Heartbeat discovery on the PC. (Data Discovery Cycle)
Or to could re-install the CM07 client.
http://www.enhansoft.com/

Oracle 8 not connecting from client machines

hello
i am using oracle 8 on windows environment. the problem is that oracle is connecting on the server machine but not on client machine for some days. sometimes i do connects but sometimes the application helds for long time and no response is obtained. Application is residing on the server and drive has been mapped on the client machines. What can be the possible cause. ping on the network is ok.
Waiting...
iftikhar ahmad
Lahore

oracle 8Wauv a historic database from 1997 - http://tonguc.wordpress.com/2006/12/27/history-of-oracle/
do you really have to stay at that version first of all, 11gR1 is out and 9iR2 is de-supported recently and I couldnt find this release's documentation also.
What about tnsping and sqlplus connection from your clients and listener status on your server - lsnrctl status
You may need to set, take and analyze sql*net traces - http://download.oracle.com/docs/cd/B19306_01/java.102/b14355/apxtblsh.htm#i1004660
Best regards.

How do I install (just the required assembles without server licence) client library to a client machine so that I can invoke SSIS/SSAS 2012 remotely?

We are trying to figure the easiest way to install client lib on a machine to call SSIS/SSAS remotely (to a SQL Server 2012).
We have some .net code referencing SMO/AMO and Microsoft.SqlServer.Management.IntegrationServices.
1) For SMO, I found out this and it is quite clear about how to install on a client machine:
Installing SMO (SQL Server Management Objects (SMO))
http://msdn.microsoft.com/en-us/library/ms162189(v=sql.110).aspx
2) For AMO (analysis management object), I found out this but I did not see a clear instruciton of what and how to install on the client machine:
http://technet.microsoft.com/en-us/library/ms124924(v=sql.110).aspx
3) For SSIS call, I did not find anything talking about the client installation.
Can someone help us?
Thanks.

Hi Sofiya,
Thank you so much for your help.
For SSIS call, we are using
Microsoft.SqlServer.Management.IntegrationServices.dll
to call package deployed to SSISDB catalog at remote server using some .net codes.
I have few questions:
1) What is the difference between
Microsoft.SqlServer.Management.IntegrationServices.dll
and the dll you mentioned:
Microsoft.SqlServer.IntegrationServices.Server.dll
2) If we install SSMS, can we also get Microsoft.SqlServer.Management.IntegrationServices.dll? Put another way, if we install SSMS, will Microsoft.SqlServer.Management.IntegrationServices.dll be registeredin GAC?
3) If we install Microsoft.SqlServer.Management.IntegrationServices.dll at client machine, I assume we don't need to licence it. (Note: SSIS package itself will be running from the remote server, NOT the client machine which is used to invoke
the SQL 2012 packages).
Best regards,
Steven Rao
Hi Steven Rao,
Yes, you are right. When you want to start a SSIS 2012 package from a .Net application,
you need to reference the assembly of Microsoft.SqlServer.Management.IntegrationServices .dll. The Microsoft.SqlServer.Management.IntegrationServices namespace contains the classes and interfaces to manage the Integration Services catalog
on an instance of SQL Server. It is only available in the GAC. For more information, see:
http://microsoft-ssis.blogspot.com/2013/01/call-ssis-2012-package-within-net.html
I also do a test, if you install the media of SQL Server Management Studio, usually, these assemblies are located in following folder as screenshot.
In the folder, C:\Windows\assembly
Regards,
Sofiya Li
Sofiya Li
TechNet Community Support

10.4.2 not recognizing extra memory module

I upgraded recently to 10.4.2, and now one of my memory modules is not recognized. the machine has the original 512M chip in the upper slot, but the 512M chip in the lower slot is not recognized. in the system profiler under hardware/diagnostics, i get:
Power On Self-Test:
Last Run:     7/15/05 7:57 PM
Result:     Failed
Failure type:     Memory
Memory slot:     SODIMM0/J25LOWER
anyone have any idea what's going on??? thx.

"However, I have another problem in that there is no startup chime on my machine, and hasn't been for a while"
Same problem with my PowerBook G4 - 1.5GHz - 512MB, only since the chime problem (not hearing it any more) has the problem with not recognizing the lower memory slot. Not certain if the two problems are related. So it seems from the discussions hear there are two solutions, $600 to repair, or purchase more memory to run in the upper slot. I do have to agree that it would be futile in my opinion to pay for the repair if the same problem emerges again, (as has been reported, at least in the forums,) meaning it could cost $1200 to fix (maybe).
"I think that terming the logic board, "fried" overstates the issue. In fact, the logic board itself is probably in good working order, thus its ability to report on the state of the lower RAM slot. The real issue is the quality of the connection from the lower slot to the logic board--essentially a bad solder. This connection can't be resoldered, so the logic board needs to be replaced."
This statement actually makes more sense then anything I have read so far.

App.config tag oracle.dataaccess.client not recognized on windows 7...

Hi all,
I have an application that is working fine on windows XP. On windows 7, the same application cannot work cause of the tag oracle.dataaccess.client you can see below which is not recognized by the system. As soon as I start the application I get an error
message
Unrecognized configuration section oracle.dataaccess.client. Can someone help please before I get nuts.
<oracle.dataaccess.client>
<settings>
<add name=""EA_SERVICES"."SLI_SECURITY_PKG"."SEC_GROUPS_ADD".RefCursor.OUTPARAM" value="implicitRefCursor bindinfo='mode=Output'"/>
<add name=""EA_SERVICES"."SLI_SECURITY_PKG"."SEC_GROUP_MEMBERS_ADD".RefCursor.OUTPARAM" value="implicitRefCursor bindinfo='mode=Output'"/>
<add name=""EA_SERVICES"."SLI_SECURITY_PKG"."SEC_OBJECTS_ADD".RefCursor.OUTPARAM" value="implicitRefCursor bindinfo='mode=Output'"/>
<add name=""EA_SERVICES"."SLI_SECURITY_PKG"."SEC_RIGHTS_ADD".RefCursor.OUTPARAM" value="implicitRefCursor bindinfo='mode=Output'"/>
<add name=""EA_SERVICES"."SLI_SECURITY_PKG"."SEC_RIGHT_GROUPS_ADD".RefCursor.OUTPARAM" value="implicitRefCursor bindinfo='mode=Output'"/>
<add name=""EA_SERVICES"."SLI_SECURITY_PKG"."SEC_USERS_ADD".RefCursor.OUTPARAM" value="implicitRefCursor bindinfo='mode=Output'"/>
</settings>
</oracle.dataaccess.client>
Sherman Body love

Since this is an oracle section, I think you'll get more help over at the oracle forums.
https://community.oracle.com/community/developer/english/oracle_database/windows_and_.net/oracle_developer_tools_for_visual_studio
I would check the versions of the odp.net (oracle.dataaccess.dll) on both machines. The XP machine probably has the 11g client on it. And the windows 7 machine probably has the 12c client on it.

Netbooted client: Apple IR-sensor not recognized

Hello forum,
have tried to get the following issue fixed for days now with no success:
• created a netboot image 10.5.3 with SIU
• netbooted a client machine with Apple IR-sensor on board
• AppleRemote won't work.
AppleRemote is tested and fully functional when I clone exactly the same image on the local HD of the client and reboot locally.
This issue applies to all my netbooted IR-capable clients on my network: 5 intel-minis, 2 intel-imacs, also to a macbook when booted via network.
It doesn't make a difference
• if the source-os for the image ist installed on an IR-enabled mac or not before image creation
• if the image itself is created on an IR-enabled mac or not
• if the image is hosted on an IR-enabled mac or not.
I am getting allways the same result: the IR-sensor is recognized in AppleSystemProfiler as USB-Device; but SystemProfiler doesn't show the AppleIRController.kext loaded; there is now enable/disable-option in the security.prefpane.
trying to kextload AppleIRController.kext results in :
kextload: /System/Library/Extensions/AppleIRController.kext loaded successfully
but no change of status in the Systemprofiler, nor in security.prefpane.
typing the same command a second time:
kextload: /System/Library/Extensions/AppleIRController.kext loaded successfully
typing a third time:
kextload: /System/Library/Extensions/AppleIRController.kext is already loaded
no change of status.
I am also able to unload the kext successfully.
Interesting: the internal iSight located on the same USB-bus is working perfectly on all machines being equipped with one.
Can't work it out - anybody found a solution for that?
robert

Tried the same procedure with fresh installed 10.5 and combo-updated to 10.5.4; no success.

SSL VPN message "This (client) machine does not have the web access privilege."

Hello!
I am trying to configure the SSL VPN (WebVPN) and I am almost done but when clicking on the URL's I configured in the bookmarks, I get the message "This (client) machine does not have the web access privilege. Please contact your SSLVPN provider for assistance." I looked through the many tutorials and guides in existence and none talks about such error and the fix for it. In fact, if I search the net for this error message I get only one match, in the Cisco website, where is say that "The client computer does not meet the security criteria of having web access functionality through the SSL VPN gateway." and as fix it gave this tip "Check the URL to the gateway or contact the administrator if it persists." So, nothing on the website about what this issue is and how to fix it. I will provide my IOS configuration and hopefully someone will spot the issue. Here it goes:
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R1
boot-start-marker
boot-end-marker
logging message-counter syslog
no logging buffered
enable secret 5 $1$1LLX$u7aTc8XfNqPZhPVGwEF/J0
enable password xxxxxxxx
aaa new-model
aaa authentication login userAuthen local
aaa authentication login sdm_vpn_xauth_ml_1 local
aaa authorization network groupauthor local
aaa session-id common
crypto pki trustpoint TP-self-signed-1279712955
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1279712955
revocation-check none
rsakeypair TP-self-signed-1279712955
crypto pki certificate chain TP-self-signed-1279712955
certificate self-signed 01
3082023A 308201A3 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31323739 37313239 3535301E 170D3130 30333233 31313030
33375A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 32373937
31323935 3530819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100A8EF 34E3E792 36660498 9801F934 E8A41865 3599EA35 B073AC91 D7A53AF4
A4390D2F CB3DB2DE 936B28F0 A25F3CE1 6F40FD9E E79096F2 F89620E0 B31A7B34
649BBA22 AE44CB55 9F38BF0C 2F2770CF 8380C167 C17D760C 380E28E4 FF7D6874
9EFC310A 2AA60835 F1AA384F CD1A0173 19C98192 EBFBD531 24CB9203 EA9E7D54
B2C30203 010001A3 62306030 0F060355 1D130101 FF040530 030101FF 300D0603
551D1104 06300482 02523130 1F060355 1D230418 30168014 0D9D62EC DA77EAF3
11ABF64D 933633F9 2BA362DC 301D0603 551D0E04 1604140D 9D62ECDA 77EAF311
ABF64D93 3633F92B A362DC30 0D06092A 864886F7 0D010104 05000381 81006853
48ED4E3E 5721C653 D9A2547C 36E4F0CB A6764B29 9AFFD30A 1B382C8C C6FDAA55
265BCF6C 51023F5D 4AF6E177 C76C4560 57DE5259 40DE4254 E79B3E13 ABD0A78D
7E0B623A 0F2D9C01 E72EF37D 5BAB72FF 65A176A1 E3709758 0229A66B 510F9AA2
495CBB4B 2CD721A7 D6F6EB43 65538BE6 B45550D7 A80A4504 E529D092 73CD
   quit
dot11 syslog
ip source-route
ip dhcp excluded-address 192.168.0.1 192.168.0.10
ip dhcp pool myPOOL
   network 192.168.0.0 255.255.255.0
   default-router 192.168.0.1
   dns-server 87.216.1.65 87.216.1.66
ip cef
ip name-server 87.216.1.65
ip name-server 87.216.1.66
ip ddns update method mydyndnsupdate
HTTP
add http://username:[email protected]/nic/update?system=dyndns&hostname=<h>&myip=<a>
interval maximum 1 0 0 0
no ipv6 cef
multilink bundle-name authenticated
vpdn enable
vpdn-group pppoe
request-dialin
protocol pppoe
username cisco privilege 15 password 0 xxxxxxxx
crypto isakmp policy 3
encr 3des
authentication pre-share
group 2
crypto isakmp fragmentation
crypto isakmp client configuration group vpnclient
key cisco123
domain selfip.net
pool ippool
acl 110
crypto ipsec transform-set myset esp-3des esp-md5-hmac
crypto dynamic-map dynmap 10
set transform-set myset
reverse-route
crypto map clientmap client authentication list userAuthen
crypto map clientmap isakmp authorization list groupauthor
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
archive
log config
hidekeys
interface Loopback0
ip address 10.11.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface Loopback2
description SSL VPN Website IP address
ip address 10.10.10.1 255.255.255.0
interface Loopback1
description SSL DHCP Pool Gateway Address
ip address 192.168.250.1 255.255.255.0
interface FastEthernet0
description $ES_LAN$
ip address 192.168.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface BRI0
no ip address
encapsulation hdlc
shutdown
interface FastEthernet1
interface FastEthernet2
switchport access vlan 2
interface FastEthernet3
interface FastEthernet4
interface FastEthernet5
interface FastEthernet6
interface FastEthernet7
interface FastEthernet8
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
bundle-enable
dsl operating-mode auto
interface Vlan1
no ip address
interface Dialer1
ip ddns update hostname myserver.selfip.net
ip ddns update mydyndnsupdate host members.dyndns.org
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip policy route-map VPN-Client
dialer pool 1
ppp chap hostname xxx
ppp chap password 0 xxxx
ppp pap sent-username xxx password 0 xxxx
crypto map clientmap
ip local pool ippool 192.168.50.100 192.168.50.200
ip local pool sslvpnpool 192.168.250.2 192.168.250.100
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer1
ip http server
ip http authentication local
ip http secure-server
ip nat inside source static tcp 192.168.0.2 21 interface Dialer1 790
ip nat inside source static tcp 192.168.0.15 21 interface Dialer1 789
ip nat inside source list 102 interface Dialer1 overload
ip nat inside source static tcp 10.10.10.1 443 interface Dialer1 443
ip nat inside source static tcp 10.10.10.1 80 interface Dialer1 80
access-list 102 deny   ip 192.168.0.0 0.0.0.255 192.168.50.0 0.0.0.255
access-list 102 permit ip 192.168.0.0 0.0.0.255 any
access-list 110 permit ip 192.168.0.0 0.0.0.255 192.168.50.0 0.0.0.255
access-list 144 permit ip 192.168.50.0 0.0.0.255 any
route-map VPN-Client permit 10
match ip address 144
set ip next-hop 10.11.0.2
control-plane
banner motd ^C
================================================================
                UNAUTHORISED ACCESS IS PROHIBITED!!!
=================================================================
^C
line con 0
line aux 0
line vty 0 4
password mypassword
transport input telnet ssh
webvpn gateway MyGateway
ip address 10.10.10.1 port 443
http-redirect port 80
ssl trustpoint TP-self-signed-1279712955
inservice
webvpn install svc flash:/webvpn/svc_1.pkg sequence 1
webvpn install csd flash:/webvpn/sdesktop.pkg
webvpn context SecureMeContext
title "My SSL VPN Service"
secondary-color #C0C0C0
title-color #808080
ssl authenticate verify all
url-list "MyServers"
   heading "My Intranet"
   url-text "Cisco" url-value "http://192.168.0.2"
   url-text "NetGear" url-value "http://192.168.0.3"
login-message "Welcome to My VPN"
policy group MyDefaultPolicy
   url-list "MyServers"
   functions svc-enabled
   svc address-pool "sslvpnpool"
   svc keep-client-installed
default-group-policy MyDefaultPolicy
aaa authentication list userAuthen
gateway MyGateway domain testvpn
max-users 100
csd enable
inservice
end
Thank you!

Hi,
Please check SAP note:
2004579 - You cannot create a FR company from a Package
Thanks & Regards,
Nagarajan

Web Forms Not working on Client Machines with Separate Win

Hi friends,
We deployed all our Forms on web and we are using Developer
Server 6.0 ,OAS 4.07, Oracle Jinitator 1.1.7.18 ,Netscape 4.7
Browser
My problem is we configured forms to open in a separate window
this is giving problems on Client Machines they are getting a
blank screen ,previously we used to open forms in the same window
(browser ) at that time we didn't get any problem.
We are using Oracle Jinitiator 1.1.7.18 & Netscape 4.7 as
browser on Client Machines.
Thanks in Advance...!
Smita T
null

JInitiator will be downloaded only once - the first time when u connect to a web-forms application. After that - no problem. It is true that the first time it takes a little bit longer, but I think forms are working better using JInitiator. However - it is just a matter of settings how u will make your application to run. Oracle did great improvement of the speed introducing the forms servlet listener. I would expect even better performance with Forms9i. And Win2000 is not a problem, but combination between Win2000 and Pentium4 is. There is a way to avoid your (installation) problems however.

Not able to create a text file in Client Machine using Forms 10g

Hi - I'm mot able to create a text file in Client Machine using Forms 10g. I'm getting error when system executes the bolded line.(i.e. CLIENT_TEXT_IO.FOPEN). During run-time system is throwing "ORA-06508: PL/SQL: could not find program unit being called".
I had attached webutil.pll in the form.
Please advise me.
DECLARE
l_Temp CLIENT_TEXT_IO.FILE_TYPE;
LC$Name Varchar2(100) ;
LC$Fic Varchar2(100) ;
LN$Lines Pls_integer := 0 ;
LC$Line Varchar2(4000) ;
Cursor C_CUR Is
Select * From TEST_TEXTIO where rownum <= 50;
BEGIN
LC$Name := 'tmp_file.txt' ;
LC$Fic := 'c:\temp\tmp_file.txt';
Begin
l_temp := CLIENT_TEXT_IO.FOPEN( 'C:\temp\tmp_file.txt', 'W');
Exception
     when others then
     message( 'OPEN FILE ERROR ' || LC$Fic ||sqlerrm );
     display_error;
     raise form_trigger_failure;
End ;
-- Write the lines --
For Cur In C_CUR Loop
     LC$Line := Cur.CODE || ' -> ' || Cur.COL1 || ',' || Cur.COL2 || ',' || Cur.Col3 ;
     CLIENT_TEXT_IO.PUT_LINE( LF$File, LC$Line ) ;
     LN$Lines := C_CUR%ROWCOUNT ;
End loop ;
-- Close the file --
CLIENT_TEXT_IO.FCLOSE( LF$File ) ;
Exception
     When others Then
message('err='||sqlerrm);message(' ');
display_error;
CLIENT_TEXT_IO.FCLOSE( LF$File ) ;
     Raise ;
END;
Thanks.
Arun

Hi ,
i have one Question though its not related to thos question if some could help me it will be really helpful,
i have created one program to import and export excel to forms vice versa, if the form is attached with webutil its working fine am using ole2.but i have a new idea if i add this program in menu, it can be used for all the forms attched to that menu, i made program also, but problem am facing right now is if the form is not attched with webutil it will not work so is there possiblity to share my webutil from one form to another form ,so i will keep one form as a interface form in that webutil will be attched ,i can share that webutil to all other forms so that all the forms no need to attach webutil again
if its possible means please suggest some ideas

Path does not exit - While trying to save file on SharPoint Server 2013 from client machine

Hi,
I have installed Microsoft SharePoint Server 2013 Enterprise Edition on my testing Lab environment (On VM Workstation 10) on Windows Server 2012 with SQL server 2012, I can access all files stored at SharePoint Server from any physical machine, I can share
a single file among different people to work simultaneously, but here i stuck on saving any file from client machine to directly on SharePoint Server, Attached is the snap shot, whenever I try to save any file directly It says Path Does Not Exist, If I drag
and drop any file directly to SharePoint I do not see any error message.
I read from different posts that I need to Enable Desktop Experience Feature on Server 2012, which I installed but no positive result gained :(
I will appreciate for any possible help?
Ali

Hi Ali,
Please try disabling the protected view per the link below and test the issue again:
http://social.technet.microsoft.com/Forums/en-US/b8381a19-3394-406f-8adb-1976f45460ef/path-does-not-exit-while-trying-to-save-file-on-sharpoint-server-2013-from-client-machine?forum=sharepointgeneral
You could simply type the url as http://sp/sites/sitename in the Filename place.
Regards,
Rebecca Tu
TechNet Community Support

ARD not recognizing client machine.

Similar Messages

Maybe you are looking for