Arghhh NOW WHAT? Black screen during installation of iLife

I'm about to pitch this G4 Powerbook! HDD died not long ago. I replaced it and couldn't find my Leopard disc. Just two weeks ago I had it in my hand! So I installed Tiger until I could find the newer cat.
Back story...
This machine was taken apart by a facility specializing in data recovery after the HDD died. I opted not to do the restore for financial reasons (would have been $1000) and I had backed the machine up recently enough. They gave the machine back to me, with RAM, old HDD, screws etc in a bag since I said I'd do the install of a new HDD.
I installed the HDD yesterday and Tiger. I have two memory chips installed, a 1GB in the lower and a 256 in the top. Computer is working fine yesterday and this morning. At one point while watching a youtube video the screen goes dark as if going to sleep. I move the cursor and it wakes up.
So I'm trying to figure out how I get Leopard back on the machine now that it is no longer in stores. Reading Discussions I learn Snow Leopard box set might be my only option but my machine requires Intel processor. I check "About this computer" for processor details and see the machine is not recognizing the 1GB memory chip. (BTW no Intel, so Snow Leopard is not an option.)
I open it up and swap slots and check again. Now the machine does not see the 256. Bad lower slot? Oh well I still have 1GB for the time being, on to building apps back up on the machine, I deal with that later.
I forget that iPhoto is not part of the OS so I grab my iLife '08 and stick it in to do install, get past the agreement page, tell it where to install etc and hit install. I walk away to check one last place the Leopard might be. Sweet! I find it and return to find the Powerbook screen dark and I can't wake it up. Fan is running, I'm tapping keys etc. Fan finally stops and it's still sleeping. I force it to shut down by holding power button down. I hit the power button and while its booting up I hear two or three loud beep tones, the indicator light on the latch blinks intermittently but the screen remains dark.
Now what?

I hit the power button and while its booting up I hear two or three loud beep tones, the indicator light on the latch blinks intermittently but the screen remains dark.
What you're hearing is a POST (Power On Self Test) error. The beeps/blinking light mean:
1 beep = no RAM installed
2 beeps = incompatible RAM types
3 beeps = no good banks
4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
5 beeps = processor is not usable
You can try swapping memory again. If you know the memory you're using is good, and you still get the POST error, that usually means it's new logic board time.

Similar Messages

Apples update didn't work for me: Boot Camp: iMac displays a black screen during installation of Windows 7

Boot Camp: iMac displays a black screen during installation of Windows 7 - Apple Support
I have followed each of the steps listed in the link above with no success.
Prior to adding the extra drivers I was able to start the Windows install process up to reformatting the "Windows" Bootcamp drive. After that the computer would go through some instal processes and eventually restart. After the restart the screen would go black. The black screen lead me to the Apple Support link above dated March 5 2015. After going through steps listed in the link above, I get an error message stating that the D:\Sources\instal.win. file cannot be located. I am forced to restart the computer at that point and theWindows install process attempts to start again but always ends up at the same point.
Note: I am installing windows 7 Pro from a DVD. I scanned the AutoUnattend.xml file and noticed that it refers to "Windows 7 ULTIMATE" but not "Pro" or any others that I could see. (see below). Could that be part of the issue?
Any feedback would be greatly appreciated.
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
</unattend>
iMac (27-inch, Late 2009)
2.66 GHz Intel Core i5
16 GB 1067 MHz DDR3
ATI Radeon HD 4850 512 MB

Here is an over-simplified explanation of WIM and CLG files. Assume your DVD Media contains
W7- Ultimate
W7- Professional
W7- Home Premium
W7- Home Basic
WIM Files
File1
y
y
y
y
File2
y
y
y
y
File3
y
File4
y
y
File4
y
y
y
The File .wim will contains a compressed image which contains File [1...5].
The W7-Ultimate .clg will have 5 entries, with all set to 'Y'.
The W7-Professional .clg will have 5 entries, with 'Y','Y','N','Y','Y'.
The W7-Home Premium .clg will have 5 entries, with 'Y','Y','N','N','Y'.
The W7-Home Basic .clg file will have 5 entries, with 'Y','Y','N','N','N'.
This allows a single .wim Image file on the DVD media to be used to install any of the 5 flavors of Windows. When you enter your product key, the Installer knows what specific W7 variant you have the key for and will tell the WIM to extract the specific files the installer needs to be extracted.
The following line
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
is telling that a retail product key will be entered, which should go look for this specific .clg file (from the five you already have on disk). You can test if it will work for you by changing this line to the following
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 PROFESSIONAL" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
If it does not work, the other issue can be related to device discovery. Typically A: and B: device names are reserved for Floppy Drives. C: is your internal HDD.
D: can either point to the Optical drive, or the USB. The normal convention is that the removable media is named from Z: backwards. Y: and Z: are usually used for Network drives, so X: should be your USB. First try with the change to "Professional". If it does not work,

IMac displays a black screen during installation of Windows 7

I tried to install windows 7 on my imac 27" but imac displays a black screen during installation of windows 7.
I also tried to install it as apples instruction of http://support.apple.com/kb/ts3173 but it failed.
Any solution please.. thanks
I have a late 27" imac with OS X 10.85

Here is an over-simplified explanation of WIM and CLG files. Assume your DVD Media contains
W7- Ultimate
W7- Professional
W7- Home Premium
W7- Home Basic
WIM Files
File1
y
y
y
y
File2
y
y
y
y
File3
y
File4
y
y
File4
y
y
y
The File .wim will contains a compressed image which contains File [1...5].
The W7-Ultimate .clg will have 5 entries, with all set to 'Y'.
The W7-Professional .clg will have 5 entries, with 'Y','Y','N','Y','Y'.
The W7-Home Premium .clg will have 5 entries, with 'Y','Y','N','N','Y'.
The W7-Home Basic .clg file will have 5 entries, with 'Y','Y','N','N','N'.
This allows a single .wim Image file on the DVD media to be used to install any of the 5 flavors of Windows. When you enter your product key, the Installer knows what specific W7 variant you have the key for and will tell the WIM to extract the specific files the installer needs to be extracted.
The following line
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
is telling that a retail product key will be entered, which should go look for this specific .clg file (from the five you already have on disk). You can test if it will work for you by changing this line to the following
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 PROFESSIONAL" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
If it does not work, the other issue can be related to device discovery. Typically A: and B: device names are reserved for Floppy Drives. C: is your internal HDD.
D: can either point to the Optical drive, or the USB. The normal convention is that the removable media is named from Z: backwards. Y: and Z: are usually used for Network drives, so X: should be your USB. First try with the change to "Professional". If it does not work,

Probelm while installing windows 7 on MacBook pro through bootcamp? I am getting a black screen during installation

Probelm while installing windows 7 on MacBook pro through bootcamp? I am getting a black screen during installation

Apple Support Boot Camp
Is there any article in the above?
did you read the pdf before beginning from Boot Camp Assistant?
Did you upgrade to Lion or was it pre-installed?

Portege 7220 and windows 98. Black screen during installation

Hi,
I am facing the following problem when I am trying to install win98 on the above machine Portege 7220 (/PIII650/64/12/13t/M), on its docking station ...
I boot from a diskete and I access the cd rom (e:\) in order to run windows 98SE setup. After I type e:\setup.exe I get a black screen and the computer freezes. However I can install windows NT or 2000 on the this machine, and moreover the windows 98SE cd runs ok on other computers, i.e. no black screen!!!!
Any idea what is wrong?
Thanks in advance,
Bar

Hi Bar
Please don`t be mad on me but I must ask you something. Do you use Win98SE full version or just update CD for Win98?
It can be that your CD is scratched! So please try another CD again or another OS like W2k!

Black screen during installation of XP on Mini

I'm trying to install XP 32 SP2 onto the kids' Mini running 10.6.4.
Disk partitioning goes fine, booting from the XP CD goes fine, the installer's first blue screen comes up just fine, I watch the usual seven tons of drivers load in the status bar at the bottom of the screen, and then... The screen goes black. I was expecting the usual questions about how to format the partition, but instead... nothing.
Any ideas?

The monitor supports both VGA and DVI-D. I was using DVI-D.
On a hunch, I slapped a DVI-D/VGA adapter on the back of the Mini and swapped in a VGA cable.
Suddenly, I got the disk formatting screen I expected instead of the black screen.

Black screen during installation of xp

Hello, everyone~~
I am trying to install win xp sp2 with bootcamp. The disk partition under Mac OS was successful. But after a system reboot, the windows installer fails to load normally. A blue screen just appears and vanishes very fast following by a black screen, with a flashing crusor. Then nothing responses and I have to restart by turning off the power supply. I tried many times but still failed to load the windows installer. Does anyone has such experience? Any help or information will be much appreciated~~
Thanks a lot.

The monitor supports both VGA and DVI-D. I was using DVI-D.
On a hunch, I slapped a DVI-D/VGA adapter on the back of the Mini and swapped in a VGA cable.
Suddenly, I got the disk formatting screen I expected instead of the black screen.

HT3986 i get a black screen during windows 7 installation on bootcamp 5.0.1

i get a black screen during windows 7 installation on bootcamp 5.0.1 , it wont install

Hi wb2009,
I haven't found that the TV would be an issue, but did find an article that states to not have extra USB devices connected.
Boot Camp: Windows installation boots to black screen with blinking cursor
http://support.apple.com/kb/TS4536
The Windows installation may boot to a black screen with a blinking cursor. This can occur if you use a USB optical drive or USB Flash drive for the Windows installation and another USB device is also connected to the computer.
There's another article that mentions Windows XP or Vista that may apply.
Archived - Boot Camp: Start up to black screen after installing Windows
http://support.apple.com/kb/TS2600
Thank you for visiting Apple Support Communities.
Nubz

Black Screen During Gameplay and not High Demand Renders?

Hi,
The computer I own has been having issues with games that it previously had no problem with. 20-30 minutes within a session the screen will go black and audio will continue momentarily. The only way out of this issue is to hold down the power button for a reset. I have updated my drivers and cleaned out any dust with pressurized air. But the problem still continues. The strange thing is that I use Photoshop and After Effects for my work and there is no issue. Need help!
Computer Specs:
Model: HP Omni 220-1150xt
OS: Windows 7 Home Premium 64-bit (6.1, Build 7601).
BIOS: Ver: LAV_7 8.ROM vLAV7.08
Processor: Intel(R) Core(TM) i7-2600S CPU @ 2.80GHz (8 CPUs), ~2.8GHz
Memory: 8192MB RAM
Available OS Memory: 8172MB RAM
DirectX Version: DirectX 11
Graphics Card name: AMD Radeon HD 6550A
Card Manufacturer: Advanced Micro Devices, Inc.

Hello masinic2,
I understand that just recently you started getting freezing and a black screen during game play and are looking to resolve it. I am providing you with an HP Support document: Using Microsoft System Restore (Windows 7), which will walk you through restoring your computer back to a point in time where you did not have this issue. This will not affect your personal files, but it will affect any applications you have installed or settings you have changed between now and the time you restore back to. You will have to reinstall or redo the changes that are undone during that time frame.
Please re-post if you require additional support. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Black screen during windows 7 install on 27inch iMac

My iMac turns to a black screen during windows 7 boot camp install. I can use the install disk on my wifes Macbook Pro so I know that the media is good.

Please re-post in the Boot Camp forum.

Hello! I want to sell my iphone 3g because i have 3gs- i cleared the info in settings and now have black screen saying no service and usb port pointing to itunes - is that all i do ?

Hello! I want to sell my iphone 3g because i have 3gs- i cleared the info in settings and now have black screen saying no service and usb port pointing to itunes - is that all i do ? i am pretty ignorant of computers- lol- i had read that i need to plug it back into itunes to verify it has all cleared out- i want to sell it on craigs list or ebay- i am really hurting for money right now- all your answers appreciated...

It needs to be restored by someone. You can do it, and set it up as a new phone, or the buyer can do it.

Black screen during startup

I get a black screen during sturtup of my MacBook Pro (April 2011): the backlight are on, but the grey screen with the apple doesn't appear.
Then, after a few, the login screen appear, and after I log in I can use my MBP normally.
I tried resetting the SMC, but nothing changes. I thought to reinstall OSX (I have 10.6), but I realized that I can't if the screen is black.
I've also tried the Apple Hardware test, but I don't see anything.
Any idea or suggestions?

Apparently I solved by resetting the PRAM.

Frozen- now all black screen. What do I do?

Hi,
THis is frustrating!
My mac screen was frozen during skype chat with my friend.
Nothing worked, so I pressed the power button to force it to turn off.
And, I turn the computer back on, and all I see is just black screen.
I hear computer starting sound, but nothing happens.
WHat should I do now? It is soooooooooooooo frustrating.
Help please!

Try things in Apple doc.#106464.
If you have trouble after that, post in the appropriate PowerBook forum. This is the G5 Tower forum.
Cheers!
DALE

[HELP] MSI Radeon R9 270X BLACK SCREEN during driver installation

Hello,
I own the R9 270X, which is on my PCI-E x16 slot, motherboard: Gigabyte ga-b85m-d3h.
When I try to install drivers for my card (those that come from AMD site, those from MSI site or those on the CD attached with card) my screen turns black in the middle of installation.
The monitor works, but there is just black screen displayed. When I restart it stays black after the Windows logo or it crashes during the usage. When it crashes it displays a solid color screen with some vertical stripes. Usually somewhere after 15 minutes from start.
My motherboard BIOS is up to date.
Card has worked great for 2 hours after fresh installation of Windows but then the problems i mentioned came back. I was even able to play games on high settings, but then the solid-color-crash occured again.
Is my card faulty and should I return it?
Specs:
Intel Core i5-4440
Gigabyte GA-B85M-D3H Intel B85 LGA 1150 mATX
Power: Corsair VS 450W ATX 120mm
Windows 8.1 64, but tested also on Windows 7 64 installed on my computer.

I'm back on my computer (where I can't install propper drivers), haven't checked with afterburner.
Two scenarios:
1. The screen started to flick/jump when we wanted to run testing game (Call Of Duty 4) on his computer, we didn't even get pass the starting window, then when we returned to Windows the flickering and jumping didn't stop. Then it was steady for a 5 second, and again flickering and jumping.
2. When I first received my newly assembled computer after fresh Windows installation I was able to play Assassins’ Creed Black Flag for about 15 minutes, then the flickering/jumping occur. Then after many trials (including removing and trying different drivers, setting up fresh windows and so on -remember, I wasn't able to even install the drivers after that) I was able to again install drivers and play for like 2 hours. Then - same as earlier problem occur.
So in conclusion, I've manage to install my drivers two times. But then the "solid color and stripes" or "jumping and flickering" problem occurred after few minutes of computer usage.
One more thing. On my computer even at low resolution the screen had some glitches (stripes here, dots there), on my friend's computer, there were no glitches at first. The flickering-and-jumping or solid-color-and-stripes problem occurs only on resolution HIGHER than 800x600.

Black screen during Windows install

Hello,
I have a late 2012 27-inch iMac with the GeForce 680MX 2GB graphics card. I'm trying to install Windows 7 or Windows 8 using Boot Camp, but neither works.
In either case, I can use the Boot Camp Assistant to create a bootable USB install disk, download the latest Windows support software from Apple, and partition the drive to allocate space for the Windows installation.
As soon as I partition the drive, the iMac restarts and tries to boot into Windows. But the only thing I ever see is a black screen (no blinking cursor), no matter how long I wait.
This seems like the exact same issue that plagued the late-2009/mid-2010 iMacs,
http://support.apple.com/kb/TS3173
In other words, it looks like the drivers included with the default Windows install disk don't work on the late 2012 iMac, at least not when configured with the 680MX.
Since this looks like the old problem but Apple doesn't appear to have provided drivers for the new iMac yet (the older iMacs above used ATI graphics, not NVIDIA), I tried to add the latest NVIDIA notebook graphics card drivers to the Windows install disk using the directions here,
http://superuser.com/questions/501812/corrupt-graphics-during-windows-8-installa tion
In particular, I used these drivers,
http://www.geforce.com/drivers/results/55125
They're not explicitly supporting the 680MX (I couldn't find any drivers for it in NVIDIA's website) but they do support the 680M and a whole slew of other cards. Thought it was worth a try.
Anyway, that didn't do the trick. Still the black screen for me.
Any ideas? Have others had this issue with the new iMacs?
Thanks

OK, I figured it out.
You know how the Boot Camp Assistant gives you three options? Create Windows Boot Disk, Download Latest Drivers, Install. You basically need to do all three at once, from scratch.
I'm not sure exactly when in the last couple of months, but Apple updated their drivers. A few days ago I gave this another shot. Initially I tried using the USB stick I had previously created, but using some of the links at the first post above, I tried to inject the new NVidia drivers provided by Apple. That didn't help. I got the black screen and all that all over again.
But then I just tried to start from scratch, remaking the USB stick while simultaneously downloading the drivers. It then also asked me if I wanted to install a new helper tool. I never got that prompt before. Either that tool solved it, or when it was creating the boot disk now it was injecting the new drivers itself in some different way.
Whatever it was, try starting from scratch and going through all the steps and you might be successful in classic "it just works" Apple fashion. Took them a couple of months, but they got there.

Arghhh NOW WHAT? Black screen during installation of iLife

Similar Messages

Maybe you are looking for