AS5300 - Voice Port Configuration Problem

Hi guys,
I'm trying to configure a E1 PRI 8 Port Module on a AS5300 (IOS: 12.3(18)) but after I configured the controller, I can't find the voice ports. if I do a sh voice port summ there are no voice ports listed.
The controller is showing up in sh controllers e1 0.
Also under the dial-peer there is no port command..
Anybody has had this issue before?
Thanks.
Best regards

here are the outputs:
Router#sh vers
Cisco Internetwork Operating System Software
IOS (tm) 5300 Software (C5300-JS-M), Version 12.3(18), RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Wed 15-Mar-06 16:39 by dchih
Image text-base: 0x60008AEC, data-base: 0x618EC000
ROM: System Bootstrap, Version 12.0(2)XD1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
BOOTLDR: 5300 Software (C5300-BOOT-M), Version 12.1(17), RELEASE SOFTWARE (fc1)
Router uptime is 3 hours, 53 minutes
System returned to ROM by reload at 16:26:08 gmt Sun Jan 2 2000
System image file is "flash:c5300-js-mz.123-18.bin"
cisco AS5300 (R4K) processor (revision A.32) with 131072K/16384K bytes of memory.
Processor board ID 14898234
R4700 CPU at 150MHz, Implementation 33, Rev 1.0, 512KB L2 Cache
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
Backplane revision 2
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x30,
Board Hardware Version 1.80, Item Number 800-2544-03,
Board Revision A0, Serial Number 14898234,
PLD/ISP Version 0.0, Manufacture Date 8-Jul-1999.
1 Ethernet/IEEE 802.3 interface(s)
1 FastEthernet/IEEE 802.3 interface(s)
35 Serial network interface(s)
240 terminal line(s)
8 Channelized E1/PRI port(s)
128K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
8192K bytes of processor board Boot flash (Read/Write)
Configuration register is 0x2102
Router#sh run
Building configuration...
Current configuration : 2057 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable password cisco
spe 1/0 2/9
firmware location system:/ucode/mica_port_firmware
resource-pool disable
clock timezone gmt 2
no aaa new-model
ip subnet-zero
ip cef
isdn switch-type primary-net5
isdn voice-call-failure 0
voice call send-alert
voice rtp send-recv
voice service pots
voice service voip
sip
voice class codec 1
voice class codec 100
controller E1 0
framing NO-CRC4
pri-group timeslots 1-31
controller E1 1
clock source line secondary 1
controller E1 2
clock source line secondary 2
controller E1 3
clock source line secondary 3
controller E1 4
clock source line secondary 4
controller E1 5
clock source line secondary 5
controller E1 6
clock source line secondary 6
controller E1 7
clock source line secondary 7
interface Ethernet0
no ip address
interface Serial0
no ip address
clock rate 2015232
no fair-queue
interface Serial1
no ip address
clock rate 2015232
no fair-queue
interface Serial2
no ip address
clock rate 2015232
no fair-queue
interface Serial3
no ip address
shutdown
clock rate 2015232
no fair-queue
interface Serial0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice modem
no cdp enable
interface FastEthernet0
ip address 1.1.1.1 255.255.255.252
duplex auto
speed auto
ip classless
ip route 0.0.0.0 0.0.0.0 1.1.1.2
no ip http server
dial-peer voice 100 voip
destination-pattern .T
session protocol sipv2
session target ipv4:192.168.1.1
session transport udp
dtmf-relay rtp-nte
dial-peer voice 10 pots
destination-pattern .T
direct-inward-dial
sip-ua
no remote-party-id
sip-server ipv4:192.168.1.1
line con 0
line 1 240
line aux 0
line vty 0 4
transport input lat pad mop telnet rlogin udptn
end
Router#
Router#sh diag
Motherboard Info:
Backplane revision 2
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x30,
Board Hardware Version 1.80, Item Number 800-2544-03,
Board Revision A0, Serial Number 14898234,
PLD/ISP Version 0.0, Manufacture Date 8-Jul-1999.
EEPROM format version 0
EEPROM contents (hex):
   0x00: 00 01 01 30 01 50 03 20 00 09 F0 03 41 00 31 34
   0x10: 38 39 38 32 33 34 00 00 00 00 00 00 00 00 13 63
   0x20: 07 08 00 00 FF FF FF FF FF FF FF FF FF FF FF FF
   0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FRU NUMBER : AS5300
Slot 0:
Hardware is Octal E1 PRI, 8 ports
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x49,
Board Hardware Version 1.0, Item Number 800-3883-01,
Board Revision A0, Serial Number 14896274,
PLD/ISP Version 0.1, Manufacture Date 29-Jun-1999.
EEPROM format version 0
EEPROM contents (hex):
   0x00: 00 01 01 49 01 00 03 20 00 0F 2B 01 41 00 31 34
   0x10: 38 39 36 32 37 34 00 00 00 00 00 00 00 00 13 63
   0x20: 06 1D 00 01 FF FF FF FF FF FF FF FF FF FF FF FF
   0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FRU NUMBER : AS53-8CE1+=
Slot 1:
Hardware is Duo Density Modems
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x4C,
Board Hardware Version 1.0, Item Number 800-3680-01,
Board Revision A0, Serial Number 14049055,
PLD/ISP Version 2.2, Manufacture Date 7-Jul-1999.
EEPROM format version 0
EEPROM contents (hex):
   0x00: 00 01 01 4C 01 00 03 20 00 0E 60 01 41 00 31 34
   0x10: 30 34 39 30 35 35 00 00 00 00 00 00 00 00 13 63
   0x20: 07 07 02 02 FF FF FF FF FF FF FF FF FF FF FF FF
   0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FRU NUMBER : AS53-120-CC2=
Slot 2:
Hardware is Duo Density Modems
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x4C,
Board Hardware Version 1.0, Item Number 800-3680-01,
Board Revision A0, Serial Number 14055218,
PLD/ISP Version 2.2, Manufacture Date 7-Jul-1999.
EEPROM format version 0
EEPROM contents (hex):
   0x00: 00 01 01 4C 01 00 03 20 00 0E 60 01 41 00 31 34
   0x10: 30 35 35 32 31 38 00 00 00 00 00 00 00 00 13 63
   0x20: 07 07 02 02 FF FF FF FF FF FF FF FF FF FF FF FF
   0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FRU NUMBER : AS53-120-CC2=
Router#

Similar Messages

Can't run form from Form Builder 10g - Port configuration problem?

Hi,
I have installed the Database (10.2.0.1.0) and the Developer Suite (10.1.2.0.2) on two Linux machines (Red Hat Enterprise Linux ES 4 Basic).
If I enter the frmservlet-URL manually everything seems to be fine.
In one case I enter http://127.0.0.1:8890/forms/frmservlet, in the other http://127.0.0.1:8889/forms/frmservlet; in BOTH cases I get eventually a dark square and the status bar says "Applet oracle.forms.engine.Main started".
HOWEVER, if I create a simple form with Form Builder and click on the Button with the green traffic light ("Run Form"), the form runs only on the machine where frmservlet listens on port 8890.
On the other machine (frmservlet configured to listen on port 8889) Firefox pops up, the URL "http://127.0.0.1:32979/6dOrpwghCqnp8PhMT7KVT533m3IaArqFbPqPBOztZXWYSsNy" gets called, and nothing else happens. The screen displays the string "ORACLE FORMS." and the status bar says "Waiting for 127.0.0.1...", and it stays like this forever.
I assume this is a port configuration problem, but I don't have a clue where to start.
Any suggestions how I should proceed are greatly appreciated.
Thank you very much in advance!

Hi Frank,
Thank you for your reply.
I doublechecked my configuration.
In the dialog Edit --> Preferences --> Runtime the Application Server URL is set to "127.0.0.1:8889/forms/frmservlet".
However, when I attempt to run the form, the URL "http://127.0.0.1:33140/W2dwbV9eXS2fPkuKlxNhCxFWdEihwDviat2uV7ycrSotqwDN" gets called.
The screen displays the string "ORACLE FORMS." and the status bar says "Waiting for 127.0.0.1...", and that's it.
I wonder how the port number 33140 got selected. Interestingly, this time it is a different number; last time it was port 32979. In fact, the port number seems to change each time; I tried again and now it is 33189.
I will now try to set the port number for the frmservlet to 8890.
I choose Edit --> Preferences --> Runtime and set the application server URL to "127.0.0.1:8890/forms/frmservlet".
I stop the container, open /home/oracle/OraHome_1/j2ee/DevSuite/config/default-web-site.xml and change the port number to 8890:
<?xml version="1.0" standalone='yes'?>
<!DOCTYPE web-site PUBLIC "Oracle Application Server 10g XML Web-site" "http://xmlns.oracle.com/ias/dtds/web-site.dtd">



<web-site port="8890" protocol="http"
display-name="Oracle Developer Suite 10g instance of Oracle Containers for J2EE Web Site">

     
     
     <default-web-app application="default" name="defaultWebApp" root="/j2ee" />

<web-app application="forms" name="formsweb" root="/forms" />


<web-app application ="reports" name="web" root="/reports" />
<web-app application = "reports" name="demo" root="/repdemo" />
     
     <access-log path="../log/default-web-access.log" />
</web-site>
I restart the container, start Form Builder, connect to the database, and open my test form.
When attempting to run the form, the URL "http://127.0.0.1:33437/Pl0n3ky9vmU5z37A7ScBnQhsGwq3jwuzJpgTAKWPMOYIzT8K" gets called (again a new port number, apparently picked radomly within a certain range) and nothing happens: "Waiting for 127.0.0.1...".
However, when I enter the URL http://127.0.0.1:8890/forms/frmservlet I do (eventually, after confirming that I trust the certificate etc.) get a darc rectangle and the status message "Applet oracle.forms.engine.Main started", which tells me that my setup can't be that far off target.
Here is the output of netstat:
[root@localhost ~]# netstat -anp --tcp
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name
tcp 0 0 0.0.0.0:32769 0.0.0.0:* LISTEN 2779/rpc.statd
tcp 0 0 0.0.0.0:23910 0.0.0.0:* LISTEN 5269/java
tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 2759/portmap
tcp 0 0 0.0.0.0:1521 0.0.0.0:* LISTEN 4265/tnslsnr
tcp 0 0 0.0.0.0:113 0.0.0.0:* LISTEN 2983/xinetd
tcp 0 0 127.0.0.1:7830 0.0.0.0:* LISTEN 4429/spamd --port 7
tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 2928/cupsd
tcp 0 0 0.0.0.0:9240 0.0.0.0:* LISTEN 5269/java
tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 3002/sendmail: acce
tcp 0 0 0.0.0.0:8890 0.0.0.0:* LISTEN 5269/java
tcp 0 0 0.0.0.0:32795 0.0.0.0:* LISTEN 4231/ora_d000_orcl
tcp 0 0 127.0.0.1:1521 127.0.0.1:32817 ESTABLISHED 4265/tnslsnr
tcp 0 0 127.0.0.1:32817 127.0.0.1:1521 ESTABLISHED 4209/ora_pmon_orcl
tcp 0 0 127.0.0.1:33425 127.0.0.1:1521 ESTABLISHED 5298/frmbld
tcp 0 0 127.0.0.1:1521 127.0.0.1:33425 ESTABLISHED 5311/oracleorcl
tcp 1 0 80.133.127.83:33485 209.132.177.100:443 CLOSE_WAIT 4060/python
tcp 1 0 80.133.127.83:33484 209.132.177.100:443 CLOSE_WAIT 4060/python
tcp 1 0 80.133.127.83:33494 209.132.177.100:443 CLOSE_WAIT 4060/python
tcp 1 0 80.133.127.83:33520 209.132.177.100:443 CLOSE_WAIT 4060/python
tcp 0 0 80.133.127.83:33529 209.132.177.100:443 ESTABLISHED 4060/python
tcp 0 0 80.133.127.83:33528 209.132.177.100:443 ESTABLISHED 4060/python
tcp 1 0 80.133.127.83:33460 209.132.177.100:443 CLOSE_WAIT 4060/python
tcp 1 0 80.133.127.83:33470 209.132.177.100:443 CLOSE_WAIT 4060/python
tcp 0 0 :::22 :::* LISTEN 2968/sshd
tcp 0 0 ::ffff:127.0.0.1:33437 :::* LISTEN 5298/frmbld
tcp 697 0 ::ffff:127.0.0.1:33437 ::ffff:127.0.0.1:33439 CLOSE_WAIT -
tcp 348 0 ::ffff:127.0.0.1:33437 ::ffff:127.0.0.1:33440 CLOSE_WAIT -
[root@localhost ~]#
The question remains: Where do those port numbers come from?
Regards,
jme

Port configuration problem

After updating Safari, my "port configuration" does not recognize the built-in ethernet option and I can't connect to the internet using Safari. Everything else works properly - Any suggestions?

Hi Jim, and a warm welcome to the forums!
Are you saying that it doesn't show at all in Network>Show:>Network Port Configurations?
If you haven't yet try this...
Safe Boot from the HD, (holding Shift key down at bootup), it will try to repair your Disk Directory while the spinning radian is happening, so let it go, run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, when complete reboot.

Serial Port Configuration Problem (SerialPortX 2.1 library)

First, thanks to the author for all of the hard work on this AppleScript library. It has worked sucessfully for me for the last two years.
However, I'm having a problem with a new-to-us scale in our laboratory. It's an older model and requires the communications settings to be 9600 / 7-E-1 with no handshaking. For novices such as myself that's 9600 bits per second, 7 data bits, even parity and 1 stop bit. I am able to successfully communicate with the scale via screen in Terminal or Serial Tools v0.4. The scale is physically attached to my Mac using a KeySpan USA-19HS serial to USB adapter.
By connecting my mac to a PC I've been able to successfully communicate between the two machines with an AppleScript using the SerialPortX library as long as all parameters match (e.g., bit rate, parity, stop bits and handshaking). The only time this fails is if the data bits is anything other than 8, which makes me think that a bug is preventing me from changing the default value (in my scale's case from 8 to 7).
Has anyone had any experience with this error? Is it possible to edit the script library to change the default to 7? Any other possible work-arounds (remember the scale is old and I can change the data bits on it)?Any advice or follow up questions are appreciated. Thanks for your time and consideration.

Thanks for the suggestion. Here's my AppleScript:
set {lf, cr} to {ASCII character 10, ASCII character 13}
set carriage_return to (cr & lf as Unicode text)
set myport to serialport list
set oh to choose from list myport
set PR to serialport open oh bps rate 9600 data bits 7 parity 2 stop bits 1 handshake 0
set cmd to "Q" & carriage_return
if PR is equal to -1 then
display dialog "could not open port "
else
serialport write cmd to PR
delay 10
set mystr to serialport read PR --for 30
delay 1
#set cmd to "OP" & lf
serialport close PR
end if
display dialog mystr

Nexus 7009 N7K-M2206FQ-23L 40GigE Port Configuration Problem

Hi,
I am experiencing a strange behaviour in configuring a 40GigE Link between two Nexus 7009 Eth6/1 and Eth9/2; both sides have a
N7K-M2206FQ-23L Module; I am using a QSFP-40GE-LR4 Optic on both sides. The Operting system is 6.2(6) on both sides.
After configuring the Interfaces as a Layer3 Interface and a no shutdown I get the message
Ethernet6/1 is down (Administratively down)
admin state is down, Dedicated Interface
So what is going wrong ?
Thanks in advance
Manfred
Ethernet6/1
transceiver is present
type is QSFP-40GE-LR4
name is CISCO
part number is FTL4C1QE1C-C1
revision is B
serial number is FNS18410KXL
nominal bitrate is 10300 MBit/sec per channel
Link length supported for 9/125um fiber is 10 km
cisco id is --
cisco extended id number is 176
cisco part number is 10-2848-01
cisco product id is QSFP-40GE-LR4
cisco vendor id is V01
Ethernet9/2
transceiver is present
type is QSFP-40GE-LR4
name is CISCO
part number is FTL4C1QE1C-C1
revision is B
serial number is FNS1834014K
nominal bitrate is 10300 MBit/sec per channel
Link length supported for 9/125um fiber is 10 km
cisco id is --
cisco extended id number is 176

Hi,
After connecting the cable to both ports, do you see green lights on the ports?
Do the interfaces go to up and up mode at all?
HTH

No non-linear under voice-port to reslove hissing on NM-HDV

Hello.
I have a trouble with 2MFT on NM-HDV.
I can hear hissing on call.
So, i had configured no non-linear under voice-port, then i can't hear any hissing.
Instead, I can hear echo on call.
How can i fix it?
Regard,
john.

Hell Venky.
Thnak you for your helping.
I tried to configure based on the web site what did you told me.
But i couldn't success it to resolve echo issue.
The voice gate have 12.4(1a) on Cisco 2851.
So the solution to reslove echo doesn't fit in my case.
As i mentioned, normally i can hear noise each i talk another persion. If i stop the conversation i can't hear noise. but i started to talk again, i can hear noise each time.
Thus i tried to disable "no non-linear" parameter, i can hear echo instead noise.
So i should choice if i can hear noise or echo.
And also, i tried to change input gain and output attenuation from -6 to 14, but the each still can hear.
out voip network toplolog is below.
NEC Digital Phone---NEC PBX---Gateway---(cat6500---MSPP(WAN Area)---cat6500)---Gateway---NEC Digital Phone.
If i make a call using Normal Phone (INot Digital Phone), I can't hear noise. Whenever i can hear noise with NEC Digital Phone.
Here is the option on cisco 2851 with 12.4
2851(config-voiceport)#?
Voice-port configuration commands:
bearer-cap Specify the bear capability
busyout Configure busyout trigger event & procedure
comfort-noise Use fill-silence option
compand-type The companding type for this voice port
connection Specify Trunking Parameters
cptone Configure voice call progress tone locale
default Set a command to its defaults
description Description of what this port is connected to
disc_pi_off close voice path when disconnect with PI received
echo-cancel Echo-cancellation option
exit Exit from voice-port configuration mode
idle-detection Idle code detection for digital voice
input Configure input gain for voice
music-threshold Threshold for Music on Hold
no Negate a command or set its defaults
non-linear Use non-linear processing during echo cancellation
output Configure output attenuation for voice
playout-delay Configure voice playout delay buffer
shutdown Take voice-port offline
threshold Threshold [noise] for voice port
timeouts Configure voice timeout parameters
translate Translation rule
translation-profile Translation profile
trunk-group Configure interface to be in a trunk group
voice-class Set voiceport voice class control parameters
Please advise to me to reslove the problem.
Regard,
john.

Purpose of local-alerting under voice-port?

Hello;
During a recent migration I noticed a "local-alerting" command under a couple voice-port configurations:
voice-port 2/1:23
local-alerting
I did not enter the command in myself, and I checked with the other engineers and all are positive they did not enter the command.
These were found under T1 PRI circuit configs and only showed up under a few (2 or 3) from a set of about 12 total circuits on 2 seperate gateways.
I tried researching this command, and it is not under any command reference doc I looked through, google was of no help as well, it does not even come up as a listed command when entering "?" under voice-port......
Is any one familiar with this command?
What does it do?
Are there any reference documents or links?
Would it be possible for it to automatically appear after certain events? (no one recalls entering this in)
Any help would be greatly appreciated.
Thank you.

This command only makes sense when local bypass of DSP is used, In which case to use DSP to generate local bypass ringback. it's a hidden command, that's probably why you don't see it in the command reference or any document avaialble.
Br,
Nadeem
Please rate all useful post.

Unable to configure voice ports on cisco2811

I have configured the Voice Gateway and calls are working internally.
I recently installed a WIC-1B-S/T-V3 card to prepare to getting outside line access.
To try a set of Dial-Peer and put the port command , but I have been rejected.
I've confirmed that　IOS Version,compatibility of WIC,PVDM is installed.
How do I get my WIC card to work?
The following is a show command.
【try set up】
R1#conf t
R1(config)#dial-peer voice 100 pots
R1(config-dial-peer)#port 0/0/0
^
% Invalid input detected at '^' marker.
R1(config-dial-peer)#port ?
<50-50> Voice interface slot #
R1(config-dial-peer)#port 50/?
<0-0> Voice interface SubUnit #
R1(config-dial-peer)#port 50/0/?
<1-20> Voice interface port # within vic
R1(config-dial-peer)#port 50/0/1
^
% Invalid input detected at '^' marker.
【show voice port summary】(i know 50/x/x voice port is automatically created.)
R1#show voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
========= == ============ ===== ==== ======== ======== ==
50/0/1 1 efxs up up on-hook idle y
50/0/1 2 efxs up up on-hook idle y
-- omission --
50/0/20 1 efxs up up on-hook idle y
50/0/20 2 efxs up up on-hook idle y
【show ip interface brief】
R1#sh ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 192.168.11.110 YES NVRAM up up
FastEthernet0/1 192.168.110.1 YES NVRAM up up
BRI0/0/0 unassigned YES NVRAM up up
BRI0/0/0:1 unassigned YES unset down down
BRI0/0/0:2 unassigned YES unset down down
Loopback0 1.1.1.1 YES NVRAM up up
【show diag】
R1#sh diag
Slot 0:
C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time unknown
Onboard VPN : v2.2.0
-- omission --
PVDM Slot 0:
16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
Hardware Revision : 4.0
Part Number : 73-8538-05
Board Revision : A0
Deviation Number : 0
Fab Version : 04
PCB Serial Number : FOC104518AZ
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM2-16
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
WIC Slot 0:
BRI S/T - 3086 WAN daughter card
Hardware Revision : 1.0
Top Assy. Part Number : 800-24973-01
Board Revision : B0
Deviation Number : 0
Fab Version : 01
PCB Serial Number : FOC10515ZRK
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : WIC-1B-S/T-V3
Version Identifier : V01
【show inventory】
R1#sh inve
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V01 , SN: FHK0934F0HR
NAME: "Wan Interface Card BRI S/T (3086)", DESCR: "Wan Interface Card BRI S/T (3086)"
PID: WIC-1B-S/T-V3 , VID: V01 , SN: FOC10515ZRK
NAME: "PVDMII DSP SIMM with one DSP", DESCR: "PVDMII DSP SIMM with one DSP"
PID: PVDM2-16 , VID: V01 , SN: FOC104518AZ
【show version】
R1#sh version
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(7), RELEASE SOFTWARE (fc6)
ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)
System returned to ROM by power-on
System image file is "flash:c2800nm-adventerprisek9-mz.124-7.bin"
Cisco 2811 (revision 53.51) with 247808K/14336K bytes of memory.
Processor board ID FHK0934F0HR
2 FastEthernet interfaces
1 ISDN Basic Rate interface
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
【show run】
R1#sh run
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R1
boot-start-marker
boot-end-marker
no aaa new-model
resource policy
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.110.1
ip dhcp pool VLAN10
network 192.168.110.0 255.255.255.0
default-router 192.168.110.1
option 150 ip 192.168.11.200
isdn switch-type ntt
voice-card 0
no dspfarm
interface Loopback0
ip address 1.1.1.1 255.255.255.255
interface FastEthernet0/0
ip address 192.168.11.110 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
ip address 192.168.110.1 255.255.255.0
duplex auto
speed auto
interface BRI0/0/0
no ip address
encapsulation hdlc
isdn switch-type ntt
isdn point-to-point-setup
isdn incoming-voice voice
isdn map address .* plan unknown type unknown
router ospf 1
log-adjacency-changes
network 1.1.1.1 0.0.0.0 area 0
network 192.168.11.0 0.0.0.255 area 0
network 192.168.110.0 0.0.0.255 area 0
router ospf 12
log-adjacency-changes
ip http server
no ip http secure-server
control-plane
dial-peer voice 100 pots
destination-pattern 0T
incoming called-number .T
direct-inward-dial
call-manager-fallback
max-conferences 8 gain -6
ip source-address 192.168.11.110 port 2000
max-ephones 10
max-dn 20 dual-line
end

Hi,
the card which u are using supports Data .
you need to have VIC cards like VIC2-2BRI-NT/TE for Voice to work.
http://www.cisco.com/c/en/us/support/docs/voice/digital-ccs/7960-2isdn-bri-vic.html
regds,
aman

Cisco 3640 cant configure voice-ports

I've an cisco 3640 with a VWIC-2MFT-E1 network module. Can anybody tell me why i cant configure any voice-port? without able to configure voice-port, i cant assign any port for my "dial-peer voice xx pots". Anybody has any solution?
what im trying to do is sending voice data traffic to 192.168.10.1
controller E1 1/0
framing NO-CRC4
clock source line primary
channel-group 0 timeslots 1-31
interface Serial1/0:0
bandwidth 2048
ip address 192.168.10.2 255.255.255.252
ip mtu 300
encapsulation ppp
no ip route-cache
no fair-queue
no cdp enable
dial-peer voice 777 pots
destination-pattern 77T
no digit-strip
direct-inward-dial
forward-digits all

I've only got this from my controller E1
Vertigo(config-controller)#?
Controller configuration commands:
channel-group     Specify the timeslots to channel-group mapping for an
                    interface
clock             Specify the clock source for a DS1 link
default           Set a command to its defaults
description       Controller specific description
detect            Enable detection of loopback request
exit              Exit from controller configuration mode
framing           Specify the type of Framing on a E1 link
guard-timer       Guard timer (0-20) for xcsp calls - timer duration and
                    accept/reject on expiry
help              Description of the interactive help system
line-termination Specify the line termination for E1
linecode          Specify the line encoding method for a E1 link
loopback          Put the entire E1 line into loopback
mode              Configure the controller mode
no                Negate a command or set its defaults
shutdown          Shut down a E1 link (send Blue Alarm)
tdm-group         Configure DS0 group for TDM
Do i need DSP for the voice-ports? Please guide me on what more module i need to get. Thanks!!
https://supportforums.cisco.com/message/3022639;jsessionid=AF45FBC0DDB8636D70F9B526A367016F.node0

Problems of Port Configuration while upgrading from 4.0B to ERP 6

Hi all,
We are upgrading a system from 4.0B to ERP 6. Will there will be any problems from port configuration side? If any please tell what they might be.
thankyou.

Hello,
We have upgraded from 4.6C to ECC6.0 and did not have any port config issues.
Things to look for:
- RFC destinations, do they still work
- directories used in File type ports, are they still there (they should be)
Hope this helps a bit
Regards
Greg Kern

System Control msg "Get Configuration port has problems

Hello !
1) Do you know what the System control manager is doing and where I can find some information about the program?
2) Do you know what the message " Get confirmation port has problems" means that comes up every time I start the computor since I installed the System control manager ?
Best regards Namretto

Comments: My system/Namretto
>>
Model: AMD Athlon(tm) XP 3200+
Speed: 2.19GHz
Model Number: 3200 (estimated)
Performance Rating: PR3177 (estimated)
Type: Standard
L2 On-board Cache: 512kB ECC Synchronous Write-Back (16-way, 64
byte line size)
Bus(es): ISA AGP PCI USB i2c/SMBus
MP Support: No
MP APIC: No
System BIOS: Phoenix Technologies, LTD 6.00 PG
Mainboard: MICRO-STAR INTERNATIONAL CO., LTD MS-6570
Total Memory: 511MB DDR-SDRAM
Model: Nvidia Corp nForce2 AGP Controller
Front Side Bus Speed: 2x 199MHz (398MHz data rate)
Total Memory: 512MB DDR-SDRAM
Memory Bus Speed: 2x 199MHz (398MHz data rate)
Monitor/Panel: Dell 1501FP (analog)
Adapter: RADEON 9600 SERIES
Adapter: RADEON 9600 SERIES - Secondary
Removable Drive: Diskettenhet
Hard Disk: ST312002 6AS SCSI Disk Device
CD-ROM/DVD: Memorex 40MAXX 1248AJ
CD-ROM/DVD: _NEC DVD_RW ND-2500A
1.44MB 3.5" (A:): N/A
Hard Disk (C:): 29.3GB (19.2GB, 65% Free) (NTFS)
Hard Disk (D:): 82.5GB (71.3GB, 86% Free) (NTFS)
CD-ROM/DVD (E:): N/A
CD-ROM/DVD (F:): N/A
Serial/Parallel Port(s): 2 COM / 1 LPT
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard Enhanced PCI to USB Host Controller
USB Controller/Hub: USB-rotnav (hub)
USB Controller/Hub: USB-rotnav (hub)
USB Controller/Hub: USB-rotnav (hub)
Keyboard: Standard 101/102-Key or Microsoft Natural PS/
2 Keyboard
Mouse: HID-compliant Cordless Mouse
Human Interface: Logitech Cordless USB Mouse
Device: NVIDIA(R) nForce(TM) Audio Codec Interface
Model: HP DeskJet 670C
Model: \\HEMPC\SKRIVARE 6
Model: \\HEMPC\SKRIVARE 3
Model: \\HEMPC\SKRIVARE
Model: \\HEMPC\PRINTER
AC Line Status: On-Line
Windows System: Microsoft Windows XP/2002 Home (Win32 x86)
5.01.2600 (Service Pack 1)
Adapter: NVIDIA nForce MCP Networking Controller
Adapter: Realtek RTL8139/810x Family Fast Ethernet NIC

Problem with the error at DIO port configuration

I am working on the design of a model of a computer controlled Fuel Injection system using Gasoline Direct Igniton technology. I am using PCI-6025E as my data card and SCB-100 Connector block. My application is to get the digital input from the shaft encoder and the solenoids[acting as Inlet and exhaust valves]get actuated according to the VI. When I am trying to run the program theres an error 10001 occured at DIO port configuration. The statement is as" The error occured at the input string, the arrangement or ordering of the characters in the string is not consistent with the expected ordering". I checked the shaft encoder[S5S-50]pin out connections using an oscillograph and the voltages are as expected. Please let me
know the possible areas where I can figure out the error.

Maruthi;
You are probably using VIs that are not supported by that DAQ device. That DAQ device of yours only allow unstrobed digital updates, meaning that the digital lines will be updated by Software calls.
Since you probably need high speed/accuracy on your digital updates, you would be better served by using the PCI-6534 instead.
Hope this helps.
Filipe A.
Applications Engineer
National Instruments

Configuration problem with external Western Digital My Book 2 TB drive

How do I fix a configuration problem with my external Western Digital My Book 2 TB drive which used to both read and write. Something has happened so that the drive is now read only? There is 600 GB of data on the drive that I cannot lose, thus am very concerned about messing around with formatting the drive which is raid 1 and filled with data.

may not like to hear, but I'd skip on MyBook cases, nice looking as they are.
Get a 2nd drive case to recover to.
http://www.macsales.com/firewire
may need to play with the demo Data Rescue 3 from Prosoft
Backup/recover before repair is usually in order
never have one backup set. THREE sets of your data, minimum.
3rd party disk maintenance and repair should be a must and given rather than rely solely on Apple Disk Utility.
Data and system maintenance and recovery plan - should be like practice for sports, arts, military with practice and making sure you will know how and the tools you need - ahead of time
Resetting USB/FW ports, try another if one won't work. When 10.6 came out there was a lot of grinding teeth with external drives not working or mounting.

How to check UC560 FXO Port Not Problem Question

Dear All,
We are newbie on Cisco UC560.
Our customer use Cisco UC560, ESW-520-24P and Cisco SPA 502G and 508G for their branch office replace old traditional PBX. Cisco UC560 have built-in VIC2-4FXO and VIC2-4FXS.
Our customer PSTN line connected to UC560 FXO port (1 line PSTN).
We receive report from our customer that they cannot make a call to PSTN and receive call from PSTN that connected to UC560 FXO port (on physical FXO port LED Green turn on). When the problem happen our customer has restart UC560 or shutdown FXO port from CLI.
We have do some test to our customer UC560.
- Moving PSTN line to another FXO port (example: port from 0/1/0 to 0/1/1). The result is same (cannot make call to PSTN and receive call from PSTN)
Today, We have checked on our customer UC560 via show voice port summary and found that port0/1/2 and 0/1/3 OPER status is up wihout cable connected to this port.
Our question:
- What command on UC560 to make sure FXO port on UC560 doesn't have problem?
We attach:
show tech-support voice
show tech-support
We hope you can give us information about this.
Thanks For Your Attention

Hi There,
If you cannot find the Indonesian "Disconnect Supervision" you may get away with using Singapores "Disconnect Supervision" as your carrier networks are similar to each other
Cheers,
David Trad.

2800 config with 4FXO VIC, voice-ports?

I'm trying to configure the voice-ports on a 2800 router with a 4 port FXO VIC and when I issue the voice-port command it only shows ports 50-50 so I use
voice-port 50/0/1 and it comes back with invalid input at marker and it points to the 50.
boot-start-marker
boot system flash flash:c2800nm-ipvoice-mz.124-4.T.bin
boot system flash flash:c2800nm-spservicesk9-mz.123-8.T8.bin
boot-end-marker
Lights on the FXO card are lit up but I do not have any cables plugged into them, am I missing something?
Thanks

I'm guessing this is the info on the pvdm2?
WIC Slot 1:
2nd generation - FXO Voice daughter card (4 port)
Hardware Revision : 5.0
Top Assy. Part Number : 800-21589-01
Board Revision : E0
Deviation Number : 0-0
Fab Version : 04
PCB Serial Number : FOC092447VB
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00

AS5300 - Voice Port Configuration Problem

Similar Messages

Maybe you are looking for