ASA 5505 ASDM username / password

Hello everyone,
I completed the PIX 515 to ASA 5505 migration today with no problems - ok one problem with the logon for ASDM.
I'm trying no username and password - then using username and password from the 515 Pix with no success.
Anyone know how to reset the username and password for the ASDM GUI website.
Thank you

Ummm,
Did you possibly try the default username/password combination? (cisco/cisco) It should then prompt you to change these settings once you gain access. I'm not familiar with how the migration works, if it transitions the user accounts over or you end up starting from scratch. Give that a try and hopefully it gets you into your new system.

Similar Messages

  • ASA 5505 ASDM problem

    I have problem with Cisco ASA 5505 (asa844-9-k8.bin) and ASDM 7.0(2) I have Windows XP with java ver 7 17
    when I click on Run ASDM, I get error Unable to launch application
    com.sun.deploy.net.FailedDownloadException: Unable to load resource: https://192.168.1.70/admin/public/asdm.jnlp
    at com.sun.deploy.net.DownloadEngine.actionDownload(Unknown Source)
    at com.sun.deploy.net.DownloadEngine._downloadCacheEntry(Unknown Source)
    at com.sun.deploy.cache.ResourceProviderImpl.getResourceCacheEntry(Unknown Source)
    at com.sun.deploy.cache.ResourceProviderImpl.getResourceCacheEntry(Unknown Source)
    at com.sun.deploy.cache.ResourceProviderImpl.getResource(Unknown Source)
    at com.sun.javaws.Launcher.updateFinalLaunchDesc(Unknown Source)
    at com.sun.javaws.Launcher.prepareToLaunch(Unknown Source)
    at com.sun.javaws.Launcher.prepareToLaunch(Unknown Source)
    at com.sun.javaws.Launcher.launch(Unknown Source)
    at com.sun.javaws.Main.launchApp(Unknown Source)
    at com.sun.javaws.Main.continueInSecureThread(Unknown Source)
    at com.sun.javaws.Main.access$000(Unknown Source)
    at com.sun.javaws.Main$1.run(Unknown Source)
    at java.lang.Thread.run(Unknown Source)
    When I click Install ASDM launcher    I get error Unable to launch devices manager from 192.168.1.70
    my run, anyway that is default, I use this ASA for CCNA Security
    asa1# sh run
    : Saved
    ASA Version 8.4(4)9
    hostname asa1
    domain-name brokenbyte.org
    enable password 8Ry2YjIyt7RRXU24 encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
    shutdown
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif management
    security-level 0
    ip address 192.168.1.70 255.255.255.0
    ftp mode passive
    dns server-group DefaultDNS
    domain-name brokenbyte.org
    pager lines 24
    mtu management 1500
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-702.bin
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication http console LOCAL
    http server enable
    http 255.255.255.255 255.255.255.255 management
    http 192.168.1.0 255.255.255.0 management
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    telnet timeout 5
    ssh timeout 5
    ssh key-exchange group dh-group1-sha1
    console timeout 0
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    anyconnect-essentials
    username zeenmc password 3/spT3R67sfjIhix encrypted privilege 15
    class-map inspection_default
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect ip-options
      inspect netbios
      inspect rsh
      inspect rtsp
      inspect skinny 
      inspect esmtp
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect sip 
      inspect xdmcp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:559d292746bf2f88f66e9acc483a68f7
    : end
    Please help me, first time, maybe before a few months, I use ASDM normaly

    I find what is problem, on the start, i think about that, but I don't find any older Java, I install now Java 6 44, now everything is OK

  • Cisco ASA 5505 (ASDM)

    Hello!
    I am new with Cisco Firewalls, I have a problem with an ASA 5505 device.
    I need 3 interfaces:
    1. OUTSIDE: this is the WAN connection (PPPOE)
    2. MAINLAN: this is the LAN for internal computers and a windows server (AD...) (IP: 10.0.0.0)
    3. WEBORDER: this is a webserver, running IIS (IP: 10.0.1.0)
    I set some NAT and Access rules in device, so MAINLAN and WEBORDER can reach internet, but this two interfaces cannot reach each other.
    I can access WEBORDER from external network (internet), but cannot access from MAINLAN.
    How can I connect the two interfaces?
    Thanks for your help.

    Hi,
    Ok, so you want to access between the local 192.168.x.x/24 and 10.0.x.x/24 networks to use their original IP addresses.
    I would suggest adding the following configurations through the same interface you used to get the CLI format configuration. Notice that you have to check the box titled "Multiple Line" so you can insert multiple lines of commands
    Configuring NAT0 for traffic between Local Networks
    NO NAT will be performed for local traffic
    access-list MAIN-LAN-NAT0 remark NO NAT for traffic between local networks
    access-list MAIN-LAN-NAT0 permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0
    access-list MAIN-LAN-NAT0 permit ip 10.0.0.0 255.255.255.0 192.168.1.0 255.255.255.0
    access-list MAIN-LAN-NAT0 permit ip 10.0.0.0 255.255.255.0 192.168.2.0 255.255.255.0
    nat (MainLan) 0 access-list MAIN-LAN-NAT0
    Remove some useless NAT configurations
    The first command removes a "global" command that is not currently in use
    The second command removes a "static" command that is not used (you have another command than handles the weborder servers NAT, this WILL NOT affect that)
    no global (Weborder) 2 interface
    no static (outside,Weborder) 10.0.1.240 xxx.xxx.xxx.xxx netmask 255.255.255.255
    Your ACLs are configured a bit different than I would personally configure them but since you ASDM the format I see on the CLI is expected.
    Guess we could try the above configurations changes first and then check if we need to try something else.
    Hope this helps
    - Jouni

  • Nat/pat asa 5505 asdm ver 8.4

    hi all,
    i have a problem with portfoarwarding on asa 5505.
    i have this situation:
    internet ---> pubblic ip address-> router albacom -- 10.0.0.15 ---> -nat farward port 80--10.0.0.1 -outside -firewall asa -inside - 192.168.0.1------------server web 192.168.0.99
    the server is not in dmz but it's on the lan network
    my user must connect from internet, with any browser http://albacom_pubblic_address and router albacom and then asa firewall must nat  and farward the port 80 on server web 192.168.0.99
    any idea or tutorial
    ths, best regards

    Hi Luca,
    On the ASA, you would need the following:
    object network server_ip
      host 192.168.0.99
    object service tcp_80
    service tcp destination eq 80
    nat (outside,inside) source static any any destination static interface server_ip service tcp_80 tcp_80
    That would port forward all the request coming on port 80 on the outside interface of the firewall, to your internal server on port 80.
    Hope that helps
    Thanks,
    Varun

  • Cisco ASA 5505 Password Problem

    I recently ran into a telnet, console, and enable password issue that was unexpected and I am hoping someone can explain what happened. 
    I had two working Cisco ASA 5505's that were two end-points of a Site-to-Site VPN.  I had used the ASDM file management tools to copy disk0 startup-config.cfg to a file named old-startup-config.cfg on disk0, on both ASA systems, and I wanted those two files to function as good working startup-config backups that I could return to, right there on the firewall, if I had to.  I also used the ASDM file management tools to make configuration "zip" backups to my local computer.  I am aware that the actual startup-config file is some type of hidden file.
    I had made some changes to both Cisco ASA 5505s, but no password changes, and everything was working great and was reloading great.  Then, I suddenly found that I needed to revert back to the old working configurations that I had backed up previously.  I used the ASDM file management tools to copy old-startup-config.cfg back to startup-config.cfg on disk0 on both machines.  I think I may have also issued the CLI command copy old-startup-config.cfg startup-config.  I asked both systems to reload without writing the running-config's to memory.
    When the systems reloaded, the console, telnet, and enable passwords were no longer recognized on the CLI and Web interface.  The interfaces loaded normally, but the passwords didn't work and the cisco default passwords didn't work either.  I had to go to each unit's physical location and perform a power cycle and console password recovery.
    I am not sure why that happened.  Is the startup-config.cfg file on disk0 an altered version of the actual startup-config configuration with missing or encrypted password credentials?  I would have never guessed in a million years that my procedure would have knocked out the enable password.
    Instead of copy startup-config.cfg old-startup-config.cfg, should I have issued the command copy startup-config old-startup-config.cfg to make a local backup of a working configuration?
    I have one more semi-related question.  If one uses ASDM file management to create a zip backup of a startup-config or running-config and then proceeds to restore a running-config, when does the restored running-config take effect? 

    If password recovery is disabled then you are locked out hard. You have to sacrifice the config to "re-admin" the appliance. Sorry for the bad news but that's the way it is by design. If there was a "back door" it would hardly be a security appliance would it?

  • ASA 5505 Username and Password

    Hi All,
    I am trying to configure an ASA 5505 with a username and password. I set all the pass words:
    password xxxxxxx
    enable password xxxxxxx
    username xxxxxx password xxxxxxx
    When I reload the device it prompts me for the username, then the password and it fails and just asks for the username again. I have even tried to delete the username/password combo but it still prompts me for it. When I do password recovery the confreg is 0x00000001. I am no ASA expert and this is getting a bit frustrating.
    When I first configured the device and reloaded it, everything worked fine.....once. Upon the second reload it just keeps prompting me.
    Thanks for any help.
    Bill

    Hello Carter,
    Hmm, it sounds like a config-register problem.
    So when you are in rommon you got to set the confreg to be on 0x41 so you can ignore the startup-config.
    Then when you enter to the ASA please do the following:
    enable password cisco
    username password cisco
    config-register 0x01
    wr
    and then finally reload,
    Regards,
    Julio

  • Cannot connect to ASDM on ASA 5505 over https

    Problem: Cannot connect to ASDM on ASA 5505 when vlan1 network is changed from the factory default.
    Hi all. I am just getting started on a new ASA 5505, working it in a test lab environment. I ran thru the initial setup wizard. During that time I specified a name for Vlan1 (changed from 'inside' to 'INTR-NET'), modified the Vlan1 IP address to use DHCP, and then populated the Device Config Access table with entries corresponding to the entire Class B network here on the local intranet. I don't recall if the factory-default network was already populated, but if it wasn't I added it as 192.168.1.0/255.255.255.0
    I then saved the config, and verified that the ASA got a dhcp address using the RS-232 console. I then reconfigured the laptop I have plugged into port 0/1 with it's normal address on the intranet and discovered that I couldn't reconnect to ASDM. The ASDM client times out, and a web browser opened to https://(ASA5505's dhcp addr) fails as well.
    I then used the console to add another http IP address matching the specific IP address (xxx.240.113.129/255.255.255.255) which the laptop is set for, to the list of permissible admin connections, but saw no difference.
    This issue is much the same as was reported in this prior forum posting:
    http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Security&topic=General&topicID=.ee6e1f8&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.2cc16cb8/4
    EXCEPT that I was already aware the admin IP address(es) needed to be registered to enable access via SSH/Telnet/HTTPS.
    And, I did that step, but it is not working. I have tried adding various combinations of network ranges in the device config access list, including the specific subnet that the lab's dhcp server assigned to the ASA 5505 (xxx.240.112.0/255.255.254.0), but there is no difference. I can traceroute to the laptop and ping the Vlan1 interface from the laptop, but the https ASDM (and ssh connections too) are not successful. This is very frustrating.
    The device is brand new, I see that upon boot it loads asa724-k8.bin, and the software banner says Cisco Adaptive Security Appliance Software Version 7.2(4)
    Note also that, from the RS-232 console, if I reset the IP address to the static, factory default (192.168.1.1) and manually config my laptop on the same subnet, then ASDM makes the connection. Just like out of the box. But when I put it back onto our intranet and verify the DHCP lease, then ASDM is a no go.
    Can you think of what I've missed?

    Good question. Let me add that info plus related Vlan config details:
    ASA5505A# show ip
    System IP Addresses:
    Interface Name IP address Subnet mask Method
    Vlan1 INTR-NET XXX.240.112.92 255.255.254.0 DHCP
    Vlan2 VoIP 172.26.99.1 255.255.255.0 manual
    Vlan3 dmz-unused 192.168.99.1 255.255.255.0 manual
    Current IP Addresses:
    Interface Name IP address Subnet mask Method
    Vlan1 INTR-NET XXX.240.112.92 255.255.254.0 DHCP
    Vlan2 VoIP 172.26.99.1 255.255.255.0 manual
    Vlan3 dmz-unused 192.168.99.1 255.255.255.0 manual
    ASA5505A# show switch vlan
    VLAN Name Status Ports
    1 INTR-NET up Et0/1, Et0/2, Et0/3, Et0/4
    2 VoIP down Et0/5, Et0/6, Et0/7
    3 dmz-unused down Et0/0
    ASA5505A#
    ASA5505A# config t
    ASA5505A(config)# show running-config http
    http server enable
    http XXX.240.0.0 255.255.0.0 INTR-NET
    http 192.168.1.0 255.255.255.0 INTR-NET
    http XXX.240.113.129 255.255.255.255 INTR-NET
    ASA5505A(config)#
    ASA5505A(config)# show running-config ssh
    ssh 192.168.1.0 255.255.255.0 INTR-NET
    ssh XXX.240.0.0 255.255.0.0 INTR-NET
    ssh timeout 5
    SECURITY LEVEL IS 100 ON Vlan1 and Vlan2, 50 on Vlan3, and traffic is restricted from Vlan3 to Vlan1 because this is the basic license.

  • Delete /remove username command in ASA-5505

    Does anybody know hot to remove a username on ASA-5505 databse using Putty ?
    Thanks.

    Hi,
    It should be simple
    Just use the following format
    no username
    You can view all the usernames on the ASA unit with the command
    show run username
    Or you can view the specific username with
    show run username
    - Jouni

  • Cisco ASA 5505 IOS 9.2(1), ASDM 7.3(2) NAT issues

    Hey all,
    I am really new to Cisco and am trying to get this Cisco ASA 5505 configured that I bought recently configured properly.
    Things I have successfully been able to do:
    1. Configure static WAN IP on WAN port e0/0 (I have a /29 block of addresses)
    2. Create static routes to point to all of my vlans that are currently being being routed through my layer 3 SG-300
    3. Install and run ASDM 7.3(2)
    4. Went through the start-up  wizard and configured all of my WAN and LAN settings (I have a WAN block of /29 addresses. So I congured my device with NAT and put in the range the first usable IP address outside of the one I configured for the direct connected WAN port from my modem. Example: 10.24.56.99-102 where .98 is already configured as the direct connect from modem to ASA 5505 and .97 is the gateway of my ISP modem.)
    The struggle that I am running into today is with NAT rules from outside to inside. I currently have an Exchange server behind this device but I am unable to get ports forwarded to it. I followed this tutorial about Static NAT, however there is still no joy. 
    http://www.networkworld.com/article/2162844/tech-primers/how-to-configure-static-nat-on-a-cisco-asa-security-appliance.html
    Attached is a copy of my running-config and version. Any help with this would be greatly appreciated. 

    Your Ethernet0/1 is a trunk with multiple VLANs allowed but you do not have corresponding VLAN interfaces for SVIs in each of the associated subnets. If, as your routing setup indicates, you will be going via your internal gateway at 10.10.1.1 to reach the internal subnets then Eth0/1 should just be an access port.
    So your Exchange server in the 10.10.12.0/24 subnet  will talk via the internal gateway (10.10.12.1?) and thus on to the ASA inside interface at 10.10.1.2.
    I assume your "public" IPs have been changed to anonymize the output. If those are your actual addresses (10.24.56.x) then there must be additional NAT taking place upstream - that would all need to be setup properly as well.

  • After i upgrade my ASA 5505 from 8.2 to 8.4 i can no longer connect to ASDM. showing connecting ..... please wait for hours now

    after i upgrade my ASA 5505 from 8.2 to 8.4 i can no longer connect to ASDM. showing connecting ..... please wait for hours now

    Ron
    I recently looked at this question with a customer who has been running 8.2 and needs to get some features in newer code. We decided that it made more sense to go to 8.4 than to 8.3.
    HTH
    Rick

  • How to set up NAT for two servers using same port with ASDM ASA 5505

    Hi there,
    We have a new installation of a ASA 5505 and are trying to get some NAT issues straightened out. Here is the scenario: On our internal network, we have two servers running Filemaker Server, a relational database server that clients connect with using port 5003. Our goal is to be able to allow users from the outside to access either of these servers as needed. I know how to set up a simple static NAT rule and matching Access rule in ASDM which would be fine for a case in which only one server using a given port is running on a network, but for simple static rules I seem to be blocked from entering a different translated port number from the orginal port number, which becomes a problem when two servers we need to access from the outside are running software using the same port number.
    What is the simplest way to address this need? I am guessing that I need to set up a scenario like this, where port 5004 (or any arbitrarily choosen unused port, can be used to access the second server:
    Outside user enters   FQDN:5004  and this translates to Database server # 1 as   192.168.1.40:5003
    and
    Outside user enters   FQDN:5003  and this translates to Database server # 1 as   192.168.1.38:5003
    If so, what is the easist way to get this done? Or is there a better what to handle this scenario?
    Thanks in advance,
    James

    I would create two objects and use object NAT
    object network Obj_5004
    host 192.168.1.40
    object network Obj_5004
    nat (inside,outside) static service tcp 5003 5004
    object network Obj_5003
    host 192.168.1.38
    object network Obj_5003
    nat (inside,outside) static service tcp 5003 5003
    Of course you will need to open your outside interface for tcp ports 5003 and 5004 to make this happen

  • Cisco ASA 5505 site to site Multiple subnet.

    Hi. I need some help configuring my cisco asa 5505.
    I've set up a VPN tunnel between two ASA 5505
    Site 1:
    Subnet 192.168.77.0
    Site 2:
    Have multiple vlans and now the tunnel goes to vlan400 - 192.168.1.0
    What I need help with:
    From site 1 i need to be able to reach another vlan on site 2. vlan480 - 192.168.20.0
    And from site 1 I need to reach 192.168.77.0 subnet from vlan480 - 192.168.20.0
    Vlan480 is used for phones. In vlan480 we have a PABX central.
    Is this possible to do?
    Any help would be greatfully appreciated!
    Config site 2:
    : Saved
    ASA Version 7.2(2)
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password x encrypted
    names
    name 192.168.1.250 DomeneServer
    name 192.168.1.10 NotesServer
    name 192.168.1.90 OvServer
    name 192.168.1.97 TerminalServer
    name 192.168.1.98 w8-eyeshare
    name 192.168.50.10 w8-print
    name 192.168.1.94 w8-app
    name 192.168.1.89 FonnaFlyMedia
    interface Vlan1
    nameif Vlan1
    security-level 100
    ip address 192.168.200.100 255.255.255.0
    ospf cost 10
    interface Vlan2
    nameif outside
    security-level 0
    ip address 79.x.x.226 255.255.255.224
    ospf cost 10
    interface Vlan400
    nameif vlan400
    security-level 100
    ip address 192.168.1.1 255.255.255.0
    ospf cost 10
    interface Vlan450
    nameif Vlan450
    security-level 100
    ip address 192.168.210.1 255.255.255.0
    ospf cost 10
    interface Vlan460
    nameif Vlan460-SuldalHotell
    security-level 100
    ip address 192.168.2.1 255.255.255.0
    ospf cost 10
    interface Vlan461
    nameif Vlan461-SuldalHotellGjest
    security-level 100
    ip address 192.168.3.1 255.255.255.0
    ospf cost 10
    interface Vlan462
    nameif Vlan462-Suldalsposten
    security-level 100
    ip address 192.168.4.1 255.255.255.0
    ospf cost 10
    interface Vlan470
    nameif vlan470-Kyrkjekontoret
    security-level 100
    ip address 192.168.202.1 255.255.255.0
    ospf cost 10
    interface Vlan480
    nameif vlan480-Telefoni
    security-level 100
    ip address 192.168.20.1 255.255.255.0
    ospf cost 10
    interface Vlan490
    nameif Vlan490-QNapBackup
    security-level 100
    ip address 192.168.10.1 255.255.255.0
    ospf cost 10
    interface Vlan500
    nameif Vlan500-HellandBadlands
    security-level 100
    ip address 192.168.30.1 255.255.255.0
    ospf cost 10
    interface Vlan510
    nameif Vlan510-IsTak
    security-level 100
    ip address 192.168.40.1 255.255.255.0
    ospf cost 10
    interface Vlan600
    nameif Vlan600-SafeQ
    security-level 100
    ip address 192.168.50.1 255.255.255.0
    ospf cost 10
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    switchport access vlan 500
    switchport trunk allowed vlan 400,450,460-462,470,480,500,510,600,610
    switchport mode trunk
    interface Ethernet0/3
    switchport access vlan 490
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    passwd x encrypted
    ftp mode passive
    clock timezone WAT 1
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    object-group service Lotus_Notes_Utgaaande tcp
    description Frim Notes og ut til alle
    port-object eq domain
    port-object eq ftp
    port-object eq www
    port-object eq https
    port-object eq lotusnotes
    port-object eq pop3
    port-object eq pptp
    port-object eq smtp
    object-group service Lotus_Notes_inn tcp
    description From alle og inn til Notes
    port-object eq www
    port-object eq lotusnotes
    port-object eq pop3
    port-object eq smtp
    object-group service Reisebyraa tcp-udp
    port-object range 3702 3702
    port-object range 5500 5500
    port-object range 9876 9876
    object-group service Remote_Desktop tcp-udp
    description Tilgang til Remote Desktop
    port-object range 3389 3389
    object-group service Sand_Servicenter_50000 tcp-udp
    description Program tilgang til Sand Servicenter AS
    port-object range 50000 50000
    object-group service VNC_Remote_Admin tcp
    description Frå oss til alle
    port-object range 5900 5900
    object-group service Printer_Accept tcp-udp
    port-object range 9100 9100
    port-object eq echo
    object-group icmp-type Echo_Ping
    icmp-object echo
    icmp-object echo-reply
    object-group service Print tcp
    port-object range 9100 9100
    object-group service FTP_NADA tcp
    description Suldalsposten NADA tilgang
    port-object eq ftp
    port-object eq ftp-data
    object-group service Telefonsentral tcp
    description Hoftun
    port-object eq ftp
    port-object eq ftp-data
    port-object eq www
    port-object eq https
    port-object eq telnet
    object-group service Printer_inn_800 tcp
    description Fra 800  nettet og inn til 400 port 7777
    port-object range 7777 7777
    object-group service Suldalsposten tcp
    description Sending av mail vha Mac Mail programmet - åpner smtp
    port-object eq pop3
    port-object eq smtp
    object-group service http2 tcp
    port-object range 81 81
    object-group service DMZ_FTP_PASSIVE tcp-udp
    port-object range 55536 56559
    object-group service DMZ_FTP tcp-udp
    port-object range 20 21
    object-group service DMZ_HTTPS tcp-udp
    port-object range 443 443
    object-group service DMZ_HTTP tcp-udp
    port-object range 8080 8080
    object-group service DNS_Query tcp
    port-object range domain domain
    object-group service DUETT_SQL_PORT tcp-udp
    description For kobling mellom andre nett og duett server
    port-object range 54659 54659
    access-list outside_access_in extended permit ip any any
    access-list outside_access_out extended permit ip any any
    access-list vlan400_access_in extended deny ip any host 149.20.56.34
    access-list vlan400_access_in extended deny ip any host 149.20.56.32
    access-list vlan400_access_in extended permit ip any any
    access-list Vlan450_access_in extended deny ip any host 149.20.56.34
    access-list Vlan450_access_in extended deny ip any host 149.20.56.32
    access-list Vlan450_access_in extended permit ip any any
    access-list Vlan460_access_in extended deny ip any host 149.20.56.34
    access-list Vlan460_access_in extended deny ip any host 149.20.56.32
    access-list Vlan460_access_in extended permit ip any any
    access-list vlan400_access_out extended permit icmp any any object-group Echo_Ping
    access-list vlan400_access_out extended permit tcp any host NotesServer object-group Lotus_Notes_Utgaaande
    access-list vlan400_access_out extended permit tcp any host DomeneServer object-group Remote_Desktop
    access-list vlan400_access_out extended permit tcp any host TerminalServer object-group Remote_Desktop
    access-list vlan400_access_out extended permit tcp any host OvServer object-group http2
    access-list vlan400_access_out extended permit tcp any host NotesServer object-group Lotus_Notes_inn
    access-list vlan400_access_out extended permit tcp any host NotesServer object-group Remote_Desktop
    access-list vlan400_access_out extended permit tcp any host w8-eyeshare object-group Remote_Desktop
    access-list vlan400_access_out extended permit tcp any host w8-app object-group Remote_Desktop
    access-list vlan400_access_out extended permit tcp any host FonnaFlyMedia range 8400 8600
    access-list vlan400_access_out extended permit udp any host FonnaFlyMedia range 9000 9001
    access-list vlan400_access_out extended permit tcp 192.168.4.0 255.255.255.0 host DomeneServer
    access-list vlan400_access_out extended permit tcp 192.168.4.0 255.255.255.0 host w8-app object-group DUETT_SQL_PORT
    access-list Vlan500_access_in extended deny ip any host 149.20.56.34
    access-list Vlan500_access_in extended deny ip any host 149.20.56.32
    access-list Vlan500_access_in extended permit ip any any
    access-list vlan470_access_in extended deny ip any host 149.20.56.34
    access-list vlan470_access_in extended deny ip any host 149.20.56.32
    access-list vlan470_access_in extended permit ip any any
    access-list Vlan490_access_in extended deny ip any host 149.20.56.34
    access-list Vlan490_access_in extended deny ip any host 149.20.56.32
    access-list Vlan490_access_in extended permit ip any any
    access-list Vlan450_access_out extended permit icmp any any object-group Echo_Ping
    access-list Vlan1_access_out extended permit ip any any
    access-list Vlan1_access_out extended permit tcp any host w8-print object-group Remote_Desktop
    access-list Vlan1_access_out extended deny ip any any
    access-list Vlan1_access_out extended permit icmp any any echo-reply
    access-list Vlan460_access_out extended permit icmp any any object-group Echo_Ping
    access-list Vlan490_access_out extended permit icmp any any object-group Echo_Ping
    access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_FTP
    access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_FTP_PASSIVE
    access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_HTTPS
    access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_HTTP
    access-list Vlan500_access_out extended permit icmp any any object-group Echo_Ping
    access-list vlan470_access_out extended permit icmp any any object-group Echo_Ping
    access-list vlan470_access_out extended permit tcp any host 192.168.202.10 object-group Remote_Desktop
    access-list Vlan510_access_out extended permit icmp any any object-group Echo_Ping
    access-list vlan480_access_out extended permit ip any any
    access-list Vlan510_access_in extended permit ip any any
    access-list Vlan600_access_in extended permit ip any any
    access-list Vlan600_access_out extended permit icmp any any
    access-list Vlan600_access_out extended permit tcp any host w8-print object-group Remote_Desktop
    access-list Vlan600_access_out extended permit tcp 192.168.1.0 255.255.255.0 host w8-print eq www
    access-list Vlan600_access_out extended permit tcp 192.168.202.0 255.255.255.0 host w8-print eq www
    access-list Vlan600_access_out extended permit tcp 192.168.210.0 255.255.255.0 host w8-print eq www
    access-list Vlan600_access_in_1 extended permit ip any any
    access-list Vlan461_access_in extended permit ip any any
    access-list Vlan461_access_out extended permit icmp any any object-group Echo_Ping
    access-list vlan400_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
    access-list outside_20_cryptomap_1 extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
    access-list outside_20_cryptomap extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
    access-list Vlan462-Suldalsposten_access_in extended permit ip any any
    access-list Vlan462-Suldalsposten_access_out extended permit icmp any any echo-reply
    access-list Vlan462-Suldalsposten_access_out_1 extended permit icmp any any echo-reply
    access-list Vlan462-Suldalsposten_access_in_1 extended permit ip any any
    pager lines 24
    logging enable
    logging asdm informational
    mtu Vlan1 1500
    mtu outside 1500
    mtu vlan400 1500
    mtu Vlan450 1500
    mtu Vlan460-SuldalHotell 1500
    mtu Vlan461-SuldalHotellGjest 1500
    mtu vlan470-Kyrkjekontoret 1500
    mtu vlan480-Telefoni 1500
    mtu Vlan490-QNapBackup 1500
    mtu Vlan500-HellandBadlands 1500
    mtu Vlan510-IsTak 1500
    mtu Vlan600-SafeQ 1500
    mtu Vlan462-Suldalsposten 1500
    no failover
    monitor-interface Vlan1
    monitor-interface outside
    monitor-interface vlan400
    monitor-interface Vlan450
    monitor-interface Vlan460-SuldalHotell
    monitor-interface Vlan461-SuldalHotellGjest
    monitor-interface vlan470-Kyrkjekontoret
    monitor-interface vlan480-Telefoni
    monitor-interface Vlan490-QNapBackup
    monitor-interface Vlan500-HellandBadlands
    monitor-interface Vlan510-IsTak
    monitor-interface Vlan600-SafeQ
    monitor-interface Vlan462-Suldalsposten
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-522.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (vlan400) 0 access-list vlan400_nat0_outbound
    nat (vlan400) 1 0.0.0.0 0.0.0.0 dns
    nat (Vlan450) 1 0.0.0.0 0.0.0.0 dns
    nat (Vlan460-SuldalHotell) 1 0.0.0.0 0.0.0.0
    nat (Vlan461-SuldalHotellGjest) 1 0.0.0.0 0.0.0.0
    nat (vlan470-Kyrkjekontoret) 1 0.0.0.0 0.0.0.0
    nat (Vlan490-QNapBackup) 1 0.0.0.0 0.0.0.0 dns
    nat (Vlan500-HellandBadlands) 1 0.0.0.0 0.0.0.0
    nat (Vlan510-IsTak) 1 0.0.0.0 0.0.0.0
    nat (Vlan600-SafeQ) 1 0.0.0.0 0.0.0.0
    nat (Vlan462-Suldalsposten) 1 0.0.0.0 0.0.0.0
    static (vlan400,outside) 79.x.x.x DomeneServer netmask 255.255.255.255
    static (vlan470-Kyrkjekontoret,outside) 79.x.x.x 192.168.202.10 netmask 255.255.255.255
    static (vlan400,outside) 79.x.x.x NotesServer netmask 255.255.255.255 dns
    static (vlan400,outside) 79.x.x.231 TerminalServer netmask 255.255.255.255
    static (vlan400,outside) 79.x.x.234 OvServer netmask 255.255.255.255
    static (vlan400,outside) 79.x.x.232 w8-eyeshare netmask 255.255.255.255
    static (Vlan490-QNapBackup,outside) 79.x.x.233 192.168.10.10 netmask 255.255.255.255 dns
    static (Vlan600-SafeQ,outside) 79.x.x.235 w8-print netmask 255.255.255.255
    static (vlan400,outside) 79.x.x.236 w8-app netmask 255.255.255.255
    static (Vlan450,vlan400) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
    static (Vlan500-HellandBadlands,vlan400) 192.168.30.0 192.168.30.0 netmask 255.255.255.0
    static (vlan400,Vlan500-HellandBadlands) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
    static (vlan400,Vlan450) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
    static (vlan400,outside) 79.x.x.252 FonnaFlyMedia netmask 255.255.255.255
    static (Vlan462-Suldalsposten,vlan400) 192.168.4.0 192.168.4.0 netmask 255.255.255.0
    static (vlan400,Vlan462-Suldalsposten) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
    static (vlan400,Vlan600-SafeQ) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
    static (Vlan600-SafeQ,vlan400) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
    static (Vlan600-SafeQ,Vlan450) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
    static (Vlan600-SafeQ,vlan470-Kyrkjekontoret) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
    static (Vlan450,Vlan600-SafeQ) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
    static (vlan470-Kyrkjekontoret,Vlan600-SafeQ) 192.168.202.0 192.168.202.0 netmask 255.255.255.0
    access-group Vlan1_access_out out interface Vlan1
    access-group outside_access_in in interface outside
    access-group outside_access_out out interface outside
    access-group vlan400_access_in in interface vlan400
    access-group vlan400_access_out out interface vlan400
    access-group Vlan450_access_in in interface Vlan450
    access-group Vlan450_access_out out interface Vlan450
    access-group Vlan460_access_in in interface Vlan460-SuldalHotell
    access-group Vlan460_access_out out interface Vlan460-SuldalHotell
    access-group Vlan461_access_in in interface Vlan461-SuldalHotellGjest
    access-group Vlan461_access_out out interface Vlan461-SuldalHotellGjest
    access-group vlan470_access_in in interface vlan470-Kyrkjekontoret
    access-group vlan470_access_out out interface vlan470-Kyrkjekontoret
    access-group vlan480_access_out out interface vlan480-Telefoni
    access-group Vlan490_access_in in interface Vlan490-QNapBackup
    access-group Vlan490_access_out out interface Vlan490-QNapBackup
    access-group Vlan500_access_in in interface Vlan500-HellandBadlands
    access-group Vlan500_access_out out interface Vlan500-HellandBadlands
    access-group Vlan510_access_in in interface Vlan510-IsTak
    access-group Vlan510_access_out out interface Vlan510-IsTak
    access-group Vlan600_access_in_1 in interface Vlan600-SafeQ
    access-group Vlan600_access_out out interface Vlan600-SafeQ
    access-group Vlan462-Suldalsposten_access_in_1 in interface Vlan462-Suldalsposten
    access-group Vlan462-Suldalsposten_access_out_1 out interface Vlan462-Suldalsposten
    route outside 0.0.0.0 0.0.0.0 79.x.x.225 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout uauth 0:05:00 absolute
    username x password x encrypted privilege 15
    aaa authentication ssh console LOCAL
    http server enable
    http 192.168.210.0 255.255.255.0 Vlan450
    http 192.168.200.0 255.255.255.0 Vlan1
    http 192.168.1.0 255.255.255.0 vlan400
    no snmp-server location
    no snmp-server contact
    snmp-server community public
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto map outside_map 20 match address outside_20_cryptomap_1
    crypto map outside_map 20 set pfs
    crypto map outside_map 20 set peer 62.92.159.137
    crypto map outside_map 20 set transform-set ESP-3DES-SHA
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp enable vlan400
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    tunnel-group 62.92.159.137 type ipsec-l2l
    tunnel-group 62.92.159.137 ipsec-attributes
    pre-shared-key *
    telnet 192.168.200.0 255.255.255.0 Vlan1
    telnet 192.168.1.0 255.255.255.0 vlan400
    telnet timeout 5
    ssh 171.68.225.216 255.255.255.255 outside
    ssh timeout 5
    console timeout 0
    dhcpd update dns both
    dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan1
    dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface outside
    dhcpd address 192.168.1.100-192.168.1.225 vlan400
    dhcpd option 6 ip DomeneServer 81.167.36.11 interface vlan400
    dhcpd option 3 ip 192.168.1.1 interface vlan400
    dhcpd enable vlan400
    dhcpd address 192.168.210.100-192.168.210.200 Vlan450
    dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan450
    dhcpd option 3 ip 192.168.210.1 interface Vlan450
    dhcpd enable Vlan450
    dhcpd address 192.168.2.100-192.168.2.150 Vlan460-SuldalHotell
    dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan460-SuldalHotell
    dhcpd option 3 ip 192.168.2.1 interface Vlan460-SuldalHotell
    dhcpd enable Vlan460-SuldalHotell
    dhcpd address 192.168.3.100-192.168.3.200 Vlan461-SuldalHotellGjest
    dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan461-SuldalHotellGjest
    dhcpd option 3 ip 192.168.3.1 interface Vlan461-SuldalHotellGjest
    dhcpd enable Vlan461-SuldalHotellGjest
    dhcpd address 192.168.202.100-192.168.202.199 vlan470-Kyrkjekontoret
    dhcpd option 3 ip 192.168.202.1 interface vlan470-Kyrkjekontoret
    dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan470-Kyrkjekontoret
    dhcpd enable vlan470-Kyrkjekontoret
    dhcpd option 3 ip 192.168.20.1 interface vlan480-Telefoni
    dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan480-Telefoni
    dhcpd address 192.168.10.80-192.168.10.90 Vlan490-QNapBackup
    dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan490-QNapBackup
    dhcpd option 3 ip 192.168.10.1 interface Vlan490-QNapBackup
    dhcpd address 192.168.30.100-192.168.30.199 Vlan500-HellandBadlands
    dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan500-HellandBadlands
    dhcpd option 3 ip 192.168.30.1 interface Vlan500-HellandBadlands
    dhcpd enable Vlan500-HellandBadlands
    dhcpd address 192.168.40.100-192.168.40.150 Vlan510-IsTak
    dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan510-IsTak
    dhcpd option 3 ip 192.168.40.1 interface Vlan510-IsTak
    dhcpd enable Vlan510-IsTak
    dhcpd address 192.168.50.150-192.168.50.199 Vlan600-SafeQ
    dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan600-SafeQ
    dhcpd enable Vlan600-SafeQ
    dhcpd address 192.168.4.100-192.168.4.150 Vlan462-Suldalsposten
    dhcpd option 6 ip DomeneServer 81.167.36.11 interface Vlan462-Suldalsposten
    dhcpd option 3 ip 192.168.4.1 interface Vlan462-Suldalsposten
    dhcpd enable Vlan462-Suldalsposten
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    prompt hostname context
    Cryptochecksum:x
    : end
    Config site 1:
    : Saved
    ASA Version 7.2(4)
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password x encrypted
    passwd x encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.77.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    pppoe client vpdn group Telenor
    ip address pppoe setroute
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    switchport access vlan 15
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    access-list outside_access_in extended permit icmp any any echo-reply log disable
    access-list outside_1_cryptomap extended permit ip 192.168.77.0 255.255.255.0 192.168.1.0 255.255.255.0
    access-list inside_nat0_outbound extended permit ip 192.168.77.0 255.255.255.0 192.168.1.0 255.255.255.0
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-524.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    access-group outside_access_in in interface outside
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    http server enable
    http 192.168.77.0 255.255.255.0 inside
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto map outside_map 1 match address outside_1_cryptomap
    crypto map outside_map 1 set pfs
    crypto map outside_map 1 set peer 79.160.252.226
    crypto map outside_map 1 set transform-set ESP-3DES-SHA
    crypto map outside_map interface outside
    crypto isakmp enable inside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet 192.168.77.0 255.255.255.0 inside
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    vpdn group Telenor request dialout pppoe
    vpdn group Telenor localname x
    vpdn group Telenor ppp authentication chap
    vpdn username x password x store-local
    dhcpd auto_config outside
    dhcpd address 192.168.77.100-192.168.77.130 inside
    dhcpd dns 192.168.77.1 interface inside
    dhcpd option 6 ip 130.67.15.198 193.213.112.4 interface inside
    dhcpd enable inside
    dhcpd option 6 ip 130.67.15.198 193.213.112.4 interface outside
    tunnel-group 79.160.252.226 type ipsec-l2l
    tunnel-group 79.160.252.226 ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:x
    : end

    Hi,
    The addition of a new network to the existing L2L VPN should be a pretty simple process.
    Essentially you will have to add the network to the Crypto ACL present in the "crypto map" configurations. You will also have to configure the NAT0 configuration for it in the proper interfaces of the ASA. These configurations are all done on both ends of the L2L VPN connection.
    Looking at your above configurations it would seem that you will need the following configurations
    SITE 1
    We add the new network to both the crypto ACL and the NAT0 ACL
    access-list outside_1_cryptomap extended permit ip 192.168.77.0 255.255.255.0 192.168.20.0 255.255.255.0
    access-list inside_nat0_outbound extended permit ip 192.168.77.0 255.255.255.0 192.168.20.0 255.255.255.0
    SITE 2
    We add the new network to the crypto ACL
    We create a new NAT0 configuration for the Vlan480 interface as it has no previous NAT0 configuration
    access-list outside_20_cryptomap_1 extended permit ip 192.168.20.0 255.255.255.0 192.168.77.0 255.255.255.0
    access-list VLAN480-NAT0 remark NAT0 for VPN
    access-list VLAN480-NAT0 permit ip 192.168.20.0 255.255.255.0 192.168.77.0 255.255.255.0
    nat (vlan480-Telefoni) 0 access-list VLAN480-NAT0
    These configurations should pretty much do the trick.
    Let me know if it worked
    - Jouni

  • Problem with ASA 5505

    Good morning,
    I'm having the following problem. I configured a ASA 5505 with VPN and a VPN Remote Access Site-to-site. Everything is working, but when I reload the ASA does not work anymore VPNs, Remote Access error 412 and the Site-to-site does not connect more to solve, I have to reset and reconfigure the ASA. This is happening dopo updating the ASA, I have version 842-k8 and asdm645-106.
    Does anyone have any idea what can be?
    Thank you.
    Running-config:
    : Saved
    : Written by master at 10:34:14.839 BRDT Mon Oct 10 2011
    ASA Version 8.4(2)
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password 2KFQnbNIdI.2KYOU encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 0
    ip address 172.16.0.140 255.255.252.0
    interface Vlan2
    nameif outside
    security-level 0
    pppoe client vpdn group gvt
    ip address pppoe setroute
    boot system disk0:/asa842-k8.bin
    ftp mode passive
    clock timezone BRST -3
    clock summer-time BRDT recurring 2 Sun Oct 0:00 3 Sun Feb 0:00
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    object network NETWORK_OBJ_172.16.0.0_22
    subnet 172.16.0.0 255.255.252.0
    object network NETWORK_OBJ_172.16.0.128_26
    subnet 172.16.0.128 255.255.255.192
    object network NETWORK_OBJ_20.0.0.0_24
    subnet 20.0.0.0 255.255.255.0
    object network NETWORK_OBJ_172.16.11.0_24
    subnet 172.16.11.0 255.255.255.0
    object-group network obj_any
    access-list 1 standard permit 172.16.0.0 255.255.252.0
    access-list 1 standard permit 20.0.0.0 255.255.255.0
    access-list outside_cryptomap extended permit ip 172.16.0.0 255.255.252.0 20.0.0.0 255.255.255.0
    access-list outside_cryptomap_1 extended permit ip 172.16.0.0 255.255.252.0 172.16.11.0 255.255.255.0
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip local pool pool 172.16.0.150-172.16.0.160 mask 255.255.252.0
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-645-106.bin
    no asdm history enable
    arp timeout 14400
    nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_22 NETWORK_OBJ_172.16.0.0_22 destination static NETWORK_OBJ_172.16.0.128_26 NETWORK_OBJ_172.16.0.128_26 no-proxy-arp route-lookup
    nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_22 NETWORK_OBJ_172.16.0.0_22 destination static NETWORK_OBJ_20.0.0.0_24 NETWORK_OBJ_20.0.0.0_24 no-proxy-arp route-lookup
    nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_22 NETWORK_OBJ_172.16.0.0_22 destination static NETWORK_OBJ_172.16.11.0_24 NETWORK_OBJ_172.16.11.0_24 no-proxy-arp route-lookup
    nat (inside,outside) after-auto source dynamic any interface
    route outside 172.16.11.0 255.255.255.0 187.16.33.131 10
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    http server enable
    http 172.16.0.0 255.255.252.0 inside
    no snmp-server location
    no snmp-server contact
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec ikev2 ipsec-proposal DES
    protocol esp encryption des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal 3DES
    protocol esp encryption 3des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES
    protocol esp encryption aes
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES192
    protocol esp encryption aes-192
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES256
    protocol esp encryption aes-256
    protocol esp integrity sha-1 md5
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 match address outside_cryptomap
    crypto map outside_map 1 set peer 189.11.56.237
    crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
    crypto map outside_map 2 match address outside_cryptomap_1
    crypto map outside_map 2 set peer 187.16.33.131
    crypto map outside_map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 2 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto ikev2 policy 1
    encryption aes-256
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 10
    encryption aes-192
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 20
    encryption aes
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 30
    encryption 3des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 40
    encryption des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 enable outside
    crypto ikev1 enable outside
    crypto ikev1 ipsec-over-tcp port 10000
    crypto ikev1 policy 10
    authentication crack
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 20
    authentication rsa-sig
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 30
    authentication pre-share
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 40
    authentication crack
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 50
    authentication rsa-sig
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 60
    authentication pre-share
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 70
    authentication crack
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 80
    authentication rsa-sig
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 90
    authentication pre-share
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 100
    authentication crack
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 110
    authentication rsa-sig
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 120
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 130
    authentication crack
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 140
    authentication rsa-sig
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 150
    authentication pre-share
    encryption des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    vpdn group gvt request dialout pppoe
    vpdn group gvt localname *******@turbonetpro
    vpdn group gvt ppp authentication pap
    vpdn username *******@turbonetpro password *****
    dhcpd auto_config outside
    dhcpd address 172.16.0.144-172.16.1.143 inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy crv internal
    group-policy crv attributes
    dns-server value 172.16.0.253 8.8.8.8
    vpn-tunnel-protocol ikev1
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value 1
    default-domain value crvnatural.com.br
    group-policy GroupPolicy_189.11.56.237 internal
    group-policy GroupPolicy_189.11.56.237 attributes
    vpn-filter value 1
    vpn-tunnel-protocol ikev1 ikev2
    group-policy GroupPolicy_187.16.33.131 internal
    group-policy GroupPolicy_187.16.33.131 attributes
    vpn-filter value 1
    vpn-tunnel-protocol ikev1 ikev2
    username master password kWH7f2vqtjMEg2Yp encrypted
    tunnel-group crv type remote-access
    tunnel-group crv general-attributes
    default-group-policy crv
    dhcp-server 172.16.0.253
    tunnel-group crv ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group 189.11.**.*** type ipsec-l2l
    tunnel-group 189.11.**.*** general-attributes
    default-group-policy GroupPolicy_189.11.**.***
    tunnel-group 189.11.**.*** ipsec-attributes
    ikev1 pre-shared-key *****
    ikev2 remote-authentication pre-shared-key ****
    ikev2 local-authentication pre-shared-key *****
    tunnel-group 187.16.33.*** type ipsec-l2l
    tunnel-group 187.16.33.*** general-attributes
    default-group-policy GroupPolicy_187.16.33.***
    tunnel-group 187.16.33.*** ipsec-attributes
    ikev1 pre-shared-key ******
    ikev2 remote-authentication pre-shared-key *****
    ikev2 local-authentication pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny 
      inspect sunrpc
      inspect xdmcp
      inspect sip 
      inspect netbios
      inspect tftp
      inspect ip-options
    service-policy global_policy global
    prompt hostname context
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:50ed6f55182534a2429d065a26e9b45c
    : end

    David,
    In order to understand why LDAP is not working run a "debug ldap 255" and then try to login or run a AAA test.
    Attach the output to find out the issue.
    Please check this out as well, to make sure that you have the correct settings:
    ASA 8.0: Configure LDAP Authentication for WebVPN Users
    HTH.
    Portu.

  • Setting up site to site vpn with cisco asa 5505

    I have a cisco asa 5505 that needs to be set up for site to site vpn to a cisco asa 5500. The 5505 is the remote office and the 5500 is the main office.
    IP of remote office router is 71.37.178.142
    IP of the main office firewall is 209.117.141.82
    Can someone tell me if my config is correct, this is the first time I am setting this up and it can not be tested until I set it up at the remote office. I would rather know its correct before I go.
    ciscoasa# show run
    : Saved
    ASA Version 7.2(4)
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password TMACBloMlcBsq1kp encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.1.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address dhcp setroute
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
    access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 host 209.117.141.82
    access-list inside_nat0_outbound extended permit ip host 71.37.178.142 host 209.117.141.82
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-524.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto map outside_map 1 match address outside_1_cryptomap
    crypto map outside_map 1 set pfs group5
    crypto map outside_map 1 set peer 209.117.141.82
    crypto map outside_map 1 set transform-set ESP-AES-256-SHA
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption aes-256
    hash sha
    group 5
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    vpdn username [email protected] password ********* store-local
    dhcpd auto_config outside
    dhcpd address 192.168.1.2-192.168.1.129 inside
    dhcpd enable inside
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:7e338fb2bf32a9ceb89560b314a5ef6c
    : end
    ciscoasa#
    Thanks!

    Hi Mandy,
    By using following access list define Peer IP as source and destination
    access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
    you are not defining the interesting traffic / subnets from both ends.
    Make some number ACL 101 as you do not have to write the extended keyword then if you like as follows, or else NAME aCL will also work:
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    access-list 101 remark CCP_ACL Category=4 access-list 101 remark IPSEC Rule
    !.1..source subnet(called local encryption domain) at your end  192.168.200.0
    !..2.and destination subnet(called remote encryption domain)at other end 192.168.100.0 !.3..I mean you have to define what subnets you need to communicate between which are behind these firewalls
    !..4...Local Subnets behind IP of the main office firewall is 209.117.141.82 say
    !...at your end  192.168.200.0
    !..5.Remote Subnets behind IP of remote office router is 71.37.178.142 say
    !...at other end 192.168.100.0
    Please use Baisc Steps as follows:
    A. Configuration in your MAIN office  having IP = 209.117.141.82  (follow step 1 to 6)
    Step 1.
    Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    Step 2.
    Config ISAKMP Policy with minimum 4 parameters are to be config for
    crypto isakmp policy 10
    authentication pre-share  ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
    encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
    hash sha   --->  3rd parameter of ISAKMP Policy is OK
    group 5  --->  4th parameter of ISAKMP Policy is OK
    lifetime 86400  ------ >  this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
    Step 3.
    Define Preshared key or PKI which you will use with other side Peer address 71.37.178.142, either key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
    Here in your case in step 2 Authentication is using PSK, looks you have not defines Password
    Use following command:
    crypto isakmp key 0 CISCO123 address 71.37.178.142
    or , but not both
    crypto isakmp key 6 CISCO123 address71.37.178.142
    step 4.
    Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
    Here is yours one:
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
    crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
    or
    crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
    Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
    ah-sha-hmac or  ah-md5-hmac
    crypto ipsec transform-set TSET1 ah-sha-hmac
    or
    crypto ipsec transform-set TSET1 ah-md5-hmac
    Step 5.
    Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
    crypto map ipsec-isakmp
    1. Define peer -- called WHO to set tunnel with
    2. Define or call WHICH - Transform Set
    3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
    Like in your case it is but ipsec-isakmp keyword missing in the ;ast
    crypto map outside_map 10 ipsec-isakmp
    1. set peer 209.117.141.82  -----> is correct as this is your other side peer called WHO in my step
    2. set transform-set TSET1  -----> is correct as this is WHICH, and only one transform set can be called
    !..In you case it is correct
    !...set transform-set ESP-AES-256-SHA (also correct)
    3.  match address outside_1_cryptomap  ---->Name of the extended ACL define as WHAT to pass through this tunnel
    4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
    Step 6.
    Now apply this one crypto MAP to your OUTSIDE interface always
    interface outside
    crypto map outside_map
    Configure the same but just change ACL on other end in step one  by reversing source and destination
    and also set the peer IP of this router in other end.
    So other side config should look as follows:
    B.  Configuration in oyur Remote PEER IP having IP = 71.37.178.142 (follow step 7 to 12)
    Step 7.
    Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
    access-list outside_1_cryptomap extended ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255
    Step 8.
    Config ISAKMP Policy with minimum 4 parameters are to be config for
    crypto isakmp policy 10
    authentication pre-share  ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
    encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
    hash sha   --->  3rd parameter of ISAKMP Policy is OK
    group 5  --->  4th parameter of ISAKMP Policy is OK
    lifetime 86400  ------ >  this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
    Step 9.
    Define Preshared key or PKI which you will use with other side Peer address key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
    Here in your case in step 8 Authentication is using PSK, looks you have not defines Password
    Use following command:
    crypto isakmp key 0 CISCO123 address 209.117.141.82
    or , but not both
    crypto isakmp key 6 CISCO123 address 209.117.141.82
    step 10.
    Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
    Here is yours one:
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
    crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
    or
    crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
    Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
    ah-sha-hmac or  ah-md5-hmac
    crypto ipsec transform-set TSET1 ah-sha-hmac
    or
    crypto ipsec transform-set TSET1 ah-md5-hmac
    Step 11.
    Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
    crypto map    ipsec-isakmp
    1. Define peer -- called WHO to set tunnel with
    2. Define or call WHICH - Transform Set, only one is permissible
    3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
    Like in your case it is but ipsec-isakmp keyword missing in the ;ast
    crypto map outside_map 10 ipsec-isakmp
    1. set peer 209.117.141.82  -----> is correct as this is your other side peer called WHO in my step
    2. set transform-set TSET1  -----> is correct as this is WHICH, and only one transform set can be called
    !..In you case it is correct
    !...set transform-set ESP-AES-256-SHA (also correct)
    3.  match address outside_1_cryptomap  ---->Name of the extended ACL define as WHAT to pass through this tunnel
    4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
    Step 12.
    Now apply this one crypto MAP to your OUTSIDE interface always
    interface outside
    crypto map outside_map
    Now initite a ping
    Here is for your summary:
    IPSec: Site to Site - Routers
    Configuration Steps
    Phase 1
    Step 1: Configure Mirrored ACL/Crypto ACL       for Interesting Traffic
    Step 2: Configure ISAKMP Policy
    Step 3: Configure ISAKMP Key
    Phase 2
    Step 4: Configure Transform Set
    Step 5: Configure Crypto Map
    Step 6: Apply Crypto Map to an Interface
    To debug for Phase 1 and Phase 2. Store it in buffer without displaying logs on terminal.
    Router#debug crpyto isakmp
    Router#debug crpyto ipsec
    Router(config)# logging buffer 7
    Router(config)# logging buffer 99999
    Router(config)# logging console 6
    Router# clear logging
    Configuration
    In R1:
    (config)# access-list 101 permit ipo host 10.1.1.1 host      10.1.2.1
    (config)# crypto isakmp policy 10
    (config-policy)# encryption 3des
    (config-policy)# authentication pre-share
    (config-policy)# group 2
    (config-policy)# hash sha1
    (config)# crypto isakmp key 0 cisco address 2.2.2.1
    (config)# crypto ipsec transform-set TSET esp-3des      sha-aes-hmac
    (config)# crypto map CMAP 10 ipsec-isakmp
    (config-crypto-map)# set peer 2.2.2.1
    (config-crypto-map)# match address 101
    (config-crypto-map)# set transform-set TSET
    (config)# int f0/0
    (config-if)# crypto map CMAP
    Similarly in R2
    Verification Commands
    #show crypto isakmp SA
    #show crypto ipsec SA
    Change to Transport Mode, add the following command in Step 4:
    (config-tranform-set)# mode transport
    Even after  doing this change, the ipsec negotiation will still be done through  tunnel mode if pinged from Loopback to Loopback. To overcome this we  make changes to ACL.
    Change to Aggressive Mode, replace the Step 3 command with these commands in R1:
    (config)# crypto isakmp peer address 2.2.2.1
    (config-peer)# set aggressive-mode password cisco
    (config-peer)# set aggressive-mode clien-endpoint       ipv4-address 2.2.2.1
    Similarly on R2.
    The below process is for the negotiation using RSA-SIG (PKI) as authentication type
    Debug Process:
    After  we debug, we can see the negotiation between the two peers. The first  packet of the interesting traffic triggers the ISAKMP (Phase1)  negotiation. Important messages are marked in BOLD and explanation in  RED
    R2(config)#do ping 10.1.1.1 so lo0 // Interesting Traffic
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
    Packet sent with a source address of 2.2.2.2
    Mar  2 16:18:42.939: ISAKMP:(0): SA request profile is (NULL) //  Router tried to find any IPSec SA matching the outgoing connection but  no valid SA has been found in Security Association Database (SADB)
    Mar  2 16:18:42.939: ISAKMP: Created a peer struct for 20.1.1.10, peer port 500
    Mar  2 16:18:42.939: ISAKMP: New peer created peer = 0x46519678 peer_handle = 0x8000000D
    Mar  2 16:18:42.939: ISAKMP: Locking peer struct 0x46519678, refcount 1 for isakmp_initiator
    Mar  2 16:18:42.939: ISAKMP: local port 500, remote port 500
    Mar  2 16:18:42.939: ISAKMP: set new node 0 to QM_IDLE    
    Mar  2 16:18:42.939: ISAKMP:(0):insert sa successfully sa = 4542B818
    Mar  2 16:18:42.939: ISAKMP:(0):Can not start Aggressive mode, trying Main mode. // Not an error. By default it is configured for Main Mode
    Mar  2 16:18:42.939: ISAKMP:(0):No pre-shared key with 20.1.1.10! // Since we are using RSA Signature, this message. If we use pre-share, this is where it would indicate so!
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-07 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-03 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-02 ID
    Mar  2 16:18:42.939: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
    Mar  2 16:18:42.939: ISAKMP:(0):Old State = IKE_READY  New State = IKE_I_MM1
    Mar  2 16:18:42.943: ISAKMP:(0): beginning Main Mode exchange
    Mar  2 16:18:42.943: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_NO_STATE // Sending ISAKMP Policy to peer
    Mar  2 16:18:42.943: ISAKMP:(0):Sending an IKE IPv4 Packet.
    Mar  2 16:18:42.943: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_NO_STATE // Sending ISAKMP Policy to peer
    Mar  2 16:18:42.947: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:42.947: ISAKMP:(0):Old State = IKE_I_MM1  New State = IKE_I_MM2
    Mar  2 16:18:42.947: ISAKMP:(0): processing SA payload. message ID = 0
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch // Do not worry about this! Not an ERROR!
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
    Mar  2 16:18:42.947:.!!!!
    Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
    R2(config)# ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): processing IKE frag vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0):Support for IKE Fragmentation not enabled
    Mar  2 16:18:42.947: ISAKMP : Scanning profiles for xauth ...
    Mar  2 16:18:42.947: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
    Mar  2 16:18:42.947: ISAKMP:      encryption 3DES-CBC
    Mar  2 16:18:42.947: ISAKMP:      hash SHA
    Mar  2 16:18:42.947: ISAKMP:      default group 2
    Mar  2 16:18:42.947: ISAKMP:      auth RSA sig
    Mar  2 16:18:42.947: ISAKMP:      life type in seconds
    Mar  2 16:18:42.947: ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80
    Mar  2 16:18:42.947: ISAKMP:(0):atts are acceptable. Next payload is 0
    Mar  2 16:18:42.947: ISAKMP:(0):Acceptable atts:actual life: 0
    Mar  2 16:18:42.947: ISAKMP:(0):Acceptable atts:life: 0
    Mar  2 16:18:42.947: ISAKMP:(0):Fill atts in sa vpi_length:4
    Mar  2 16:18:42.947: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
    Mar  2 16:18:42.947: ISAKMP:(0):Returning Actual lifetime: 86400
    Mar  2 16:18:42.947: ISAKMP:(0)::Started lifetime timer: 86400.
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.951: ISAKMP:(0): processing IKE frag vendor id payload
    Mar  2 16:18:42.951: ISAKMP:(0):Support for IKE Fragmentation not enabled
    Mar  2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2  New State = IKE_I_MM2
    Mar  2 16:18:42.951: ISAKMP (0): constructing CERT_REQ for issuer cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
    Mar  2 16:18:42.951: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_SA_SETUP // Sending Key Exchange Information to peer
    Mar  2 16:18:42.951: ISAKMP:(0):Sending an IKE IPv4 Packet.
    Mar  2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2  New State = IKE_I_MM3
    Mar  2 16:18:42.955: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_SA_SETUP // Receive key exchange information from peer
    Mar  2 16:18:42.955: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:42.955: ISAKMP:(0):Old State = IKE_I_MM3  New State = IKE_I_MM4
    Mar  2 16:18:42.959: ISAKMP:(0): processing KE payload. message ID = 0
    Mar  2 16:18:43.003: ISAKMP:(0): processing NONCE payload. message ID = 0
    Mar  2 16:18:43.007: ISAKMP:(1008): processing CERT_REQ payload. message ID = 0
    Mar  2 16:18:43.007: ISAKMP:(1008): peer wants a CT_X509_SIGNATURE cert
    Mar  2 16:18:43.007: ISAKMP:(1008): peer wants cert issued by cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
    Mar  2 16:18:43.007:  Choosing trustpoint CA_Server as issuer
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID is Unity
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID seems Unity/DPD but major 180 mismatch
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID is XAUTH
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): speaking to another IOS box!
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008):vendor ID seems Unity/DPD but hash mismatch
    Mar  2 16:18:43.007: ISAKMP:received payload type 20
    Mar  2 16:18:43.007: ISAKMP (1008): His hash no match - this node outside NAT
    Mar  2 16:18:43.007: ISAKMP:received payload type 20
    Mar  2 16:18:43.007: ISAKMP (1008): No NAT Found for self or peer
    Mar  2 16:18:43.007: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:43.007: ISAKMP:(1008):Old State = IKE_I_MM4  New State = IKE_I_MM4
    Mar  2 16:18:43.011: ISAKMP:(1008):Send initial contact
    Mar  2 16:18:43.011: ISAKMP:(1008):My ID configured as IPv4 Addr, but Addr not in Cert!
    Mar  2 16:18:43.011: ISAKMP:(1008):Using FQDN as My ID
    Mar  2 16:18:43.011: ISAKMP:(1008):SA is doing RSA signature authentication using id type ID_FQDN
    Mar  2 16:18:43.011: ISAKMP (1008): ID payload
              next-payload : 6
              type         : 2
              FQDN name    : R2
              protocol     : 17
              port         : 500
              length       : 10
    Mar  2 16:18:43.011: ISAKMP:(1008):Total payload length: 10
    Mar  2 16:18:43.019: ISAKMP (1008): constructing CERT payload for hostname=R2+serialNumber=FHK1502F2H8
    Mar  2 16:18:43.019: ISAKMP:(1008): using the CA_Server trustpoint's keypair to sign
    Mar  2 16:18:43.035: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_KEY_EXCH
    Mar  2 16:18:43.035: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.035: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:43.035: ISAKMP:(1008):Old State = IKE_I_MM4  New State = IKE_I_MM5
    Mar  2 16:18:43.047: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_KEY_EXCH
    // "MM_KEY_EXCH" indicates that the peers have exchanged DH Public keys and generated a shared secret!
    Mar  2 16:18:43.047: ISAKMP:(1008): processing ID payload. message ID = 0
    Mar  2 16:18:43.047: ISAKMP (1008): ID payload
              next-payload : 6
              type         : 2
              FQDN name    : ASA1
              protocol     : 0
              port         : 0
              length       : 12
    Mar  2 16:18:43.047: ISAKMP:(0):: peer matches *none* of the profiles // Normal Message! Not an error!
    Mar  2 16:18:43.047: ISAKMP:(1008): processing CERT payload. message ID = 0
    Mar  2 16:18:43.047: ISAKMP:(1008): processing a CT_X509_SIGNATURE cert
    Mar  2 16:18:43.051: ISAKMP:(1008): peer's pubkey isn't cached
    Mar  2 16:18:43.059: ISAKMP:(1008): Unable to get DN from certificate!
    Mar  2 16:18:43.059: ISAKMP:(1008): Cert presented by peer contains no OU field.
    Mar  2 16:18:43.059: ISAKMP:(0):: peer matches *none* of the profiles
    Mar  2 16:18:43.063: ISAKMP:(1008): processing SIG payload. message ID = 0
    Mar  2 16:18:43.067: ISAKMP:received payload type 17
    Mar  2 16:18:43.067: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.067: ISAKMP:(1008): vendor ID is DPD
    Mar  2 16:18:43.067: ISAKMP:(1008):SA authentication status:
              authenticated
    Mar  2 16:18:43.067: ISAKMP:(1008):SA has been authenticated with 20.1.1.10
    Mar  2 16:18:43.067: ISAKMP: Trying to insert a peer 40.1.1.1/20.1.1.10/500/,  and inserted successfully 46519678. // SA inserted into SADB
    Mar  2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM5  New State = IKE_I_MM6
    Mar  2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM6  New State = IKE_I_MM6
    Mar  2 16:18:43.071: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:43.071: ISAKMP:(1008):Old State = IKE_I_MM6  New State = IKE_P1_COMPLETE
    Mar  2 16:18:43.071: ISAKMP:(1008):beginning Quick Mode exchange, M-ID of -1523793378
    Mar  2 16:18:43.071: ISAKMP:(1008):QM Initiator gets spi
    Mar  2 16:18:43.075: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE    
    Mar  2 16:18:43.075: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.075: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
    Mar  2 16:18:43.075: ISAKMP:(1008):Old State = IKE_QM_READY  New State = IKE_QM_I_QM1
    Mar  2 16:18:43.075: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
    Mar  2 16:18:43.075: ISAKMP:(1008):Old State = IKE_P1_COMPLETE  New State = IKE_P1_COMPLETE
    Mar  2 16:18:43.079: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) QM_IDLE // IPSec Policies
    Mar  2 16:18:43.079: ISAKMP:(1008): processing HASH payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing SA payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008):Checking IPSec proposal 1
    Mar  2 16:18:43.079: ISAKMP: transform 1, ESP_3DES
    Mar  2 16:18:43.079: ISAKMP:   attributes in transform:
    Mar  2 16:18:43.079: ISAKMP:      SA life type in seconds
    Mar  2 16:18:43.079: ISAKMP:      SA life duration (basic) of 3600
    Mar  2 16:18:43.079: ISAKMP:      SA life type in kilobytes
    Mar  2 16:18:43.079: ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0
    Mar  2 16:18:43.079: ISAKMP:      encaps is 1 (Tunnel)
    Mar  2 16:18:43.079: ISAKMP:      authenticator is HMAC-SHA
    Mar  2 16:18:43.079: ISAKMP:(1008):atts are acceptable. // IPSec attributes are acceptable!
    Mar  2 16:18:43.079: ISAKMP:(1008): processing NONCE payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
    Mar  2 16:18:43.083: ISAKMP:(1008): Creating IPSec SAs
    Mar  2 16:18:43.083:         inbound SA from 20.1.1.10 to 40.1.1.1 (f/i)  0/ 0
              (proxy 1.1.1.1 to 2.2.2.2)
    Mar  2 16:18:43.083:         has spi 0xA9A66D46 and conn_id 0
    Mar  2 16:18:43.083:         lifetime of 3600 seconds
    Mar  2 16:18:43.083:         lifetime of 4608000 kilobytes
    Mar  2 16:18:43.083:         outbound SA from 40.1.1.1 to 20.1.1.10 (f/i) 0/0
              (proxy 2.2.2.2 to 1.1.1.1)
    Mar  2 16:18:43.083:         has spi  0x2B367FB4 and conn_id 0
    Mar  2 16:18:43.083:         lifetime of 3600 seconds
    Mar  2 16:18:43.083:         lifetime of 4608000 kilobytes
    Mar  2 16:18:43.083: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE    
    Mar  2 16:18:43.083: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.083: ISAKMP:(1008):deleting node -1523793378 error FALSE reason "No Error"
    Mar  2 16:18:43.083: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
    Mar  2 16:18:43.083: ISAKMP:(1008):Old State = IKE_QM_I_QM1  New State = IKE_QM_PHASE2_COMPLETE // At this point tunnels are up and ready to pass traffic!
    Verification Commands
    #show crypto isakmp SA
    #show crypto ipsec SA
    Kindly rate if you find the explanation useful !!
    Best Regards
    Sachin Garg

  • Connect Inside to Outside in ASA 5505

    Hi there,
    I have a test ASA 5505 with the setting below:
    How can I connect to the internet (Vlan 1 to VLan 11)
    TestASA5505#  show run
    : Saved
    ASA Version 8.2(4)
    hostname TestASA5505
    domain-name default.domain.invalid
    enable password 8Ry2YjIyt7RRXU24 encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
    switchport access vlan 11
    interface Ethernet0/1
    switchport access vlan 3
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.99.1 255.255.255.0
    interface Vlan11
    nameif outside
    security-level 0
    ip address 192.168.1.4 255.255.255.0
    boot system disk0:/asa824-k8.bin
    ftp mode passive
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-647.bin
    no asdm history enable
    arp timeout 14400
    route outside 0.0.0.0 255.255.255.255 192.168.1.4 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-record DfltAccessPolicy
    http server enable
    http 192.168.99.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    management-access inside
    dhcpd address 192.168.99.3-192.168.99.30 inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    ssl encryption 3des-sha1 aes128-sha1 aes256-sha1 rc4-md5
    webvpn
    username admin password S1xyD1w.ZbjUT1yX encrypted privilege 15
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    prompt hostname context
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:096682b0996d6a1cad76597c01ffe5e2
    : end
    TestASA5505#
    Thank you in Advance for your time

    Hi,
    What device is in front of the ASA?
    Is there some ADSL modem doing NAT and providing Internet connection or something?
    One obvious problem in the above configuration is the route
    route outside 0.0.0.0 255.255.255.255 192.168.1.4 1
    Its not actually even a default route and furthermore its pointing to the ASA itself
    It should be something like this
    route outside 0.0.0.0 0.0.0.0 192.168.1.x
    Where the 192.168.1.x is the IP of the device providing the Internet connectivity to the ASA (Since ASA "outside" interface is using private IP address range)
    If there ASA doesnt need to do any NAT then you could also add this
    access-list INSIDE-NAT0 permit ip 192.168.99.0 255.255.255.0 any
    nat (inside) 0 access-list INSIDE-NAT0
    Also your DHCP configurations dont have any DNS servers defined.
    dhcpd dns
    - Jouni

Maybe you are looking for

  • Logic 7.1.1 crashes on startup on 10.6.7?

    I have been using Logic Express 7.1.1 for many years now.  I last used it on May 13th according to the preferences. Today, when I try to open it, it instantly crashes.  I have tried removing preferences, application support files and even the Library

  • Mouse disconects

    My wireless super mouse disconects-reconects sporadically.  The pointer will lag and be in accurate.  I have a 21.5 mid-2011 i5core 4gb iMac running lion.

  • How do you unlink stereo audio files as opt-L did under FCP 7?

    Under Final Cut 7, I was able to unlink a stereo file and move the left and right tracks independently forwared and back (manually stereoizing the sound if I wanted to).  I see how expand an audio sound and changing panning on left and right, but no

  • Losing value after split/join

    Hi, In my process, there is a split/join activity. Before the split, there is an interactivity activity. User can set the BPMObject values. Then, in the split/join, all interactive activities can change the BPMObject values. Before the join, the proc

  • Moved my laptop and now I can't connect to the router

    I'm a novice at this - but that didn't stop me from setting up a wireless network  - it was very easy, everything went fine and was working great for months.  I took the laptop out of the house and used it at another location.  When I brought the lap