ASA 5505 Backup

Hello i have two ASA5505 .
On one i have erased disk0 and i can't access it over ASDM...
I have copied the 2bin files asa-k8.bin and asdm-k8.bin from the working ASA to the ereased still no ASDM...
My questions are :
Are the licenses gone?
What should i do to fix it?
I have a backup.zip from the working one. Can i import it in the ereased with CLI ?
Thanks

Hello,
Can you share to the community how you did it ?
So if someone having the same issue can fix it with this
For more information about Core and Security Networking follow my website at http://laguiadelnetworking.
Any question contact me at [email protected]
Cheers,
Julio Carvajal Segura

Similar Messages

ASA 5505 backup interface

Hello,
I have setup ASA 5505 with 2 ISP, named outside (primary) and backup, the scenario is if outside down, then backup will take over, it works now.
But it is not working when the primary connection cannot reach the gateway with the interface still up.
Is it possible when the primary connection cannot reach the gateway then backup automatically take over?
Thanks before..
My configuration is:
ASA Version 8.2(1)
hostname cisco
domain-name default_domain
enable password ********* encrypted
passwd ********* encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.254 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 172.10.10.10 255.255.255.0
interface Vlan3
no forward interface Vlan2
nameif backup
security-level 0
ip address 172.20.10.10 255.255.255.0
interface Ethernet0/0
switchport access vlan 1
interface Ethernet0/1
switchport access vlan 2
interface Ethernet0/2
switchport access vlan 3
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
domain-name default domain
same-security-traffic permit intra-interface
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu backup 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (inside) 1 interface
global (outside) 1 interface
global (backup) 1 interface
nat (inside) 1 192.168.1.0 255.255.255.0
access-group inside_out in interface inside
access-group outside_in in interface outside
access-group backup_in in interface backup
route outside 0.0.0.0 0.0.0.0 172.10.10.1 1
route backup 0.0.0.0 0.0.0.0 172.20.10.1 254
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet 192.168.1.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd lease 1048575
dhcpd auto_config outside
dhcpd address 192.168.1.100-192.168.1.200 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect icmp
service-policy global_policy global
prompt hostname context
Cryptochecksum:24af050f332deab3e38eb578f8081d05
: end

Hi Amrin,
you can configure SLA monitoring on ASA and that woudl work fine for you:
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00806e880b.shtml
Hope that helps.
Thanks,
Varun

ASA 5505 - Backup and restore to another device of same model and version

How can I backup the configuration of the ASA 5505 on 8.x and restore it to another ASA 5505 with same version? I have tried to save the running config to a file and then copy it to the new device and use the boot config: filename but it doesn't work. Or is there any other way to try? Thanks.

Thanks Andrew, I had tried it but I was having issues with the fact that I kept both ver 7 and ver 8 of the OS images on the flash. So it booted from the first found (ver 7) and creating confusion for me as the config file was for ver 8.
I noticed that it keeps the 192.168.1.1 IP even though in the config file it has another IP assigned. Is there other things that I need to check that do not change apart the IP address?
Thanks.

ASA 5505 Backup Config to TFTP Server

Is there a way to backup the configuration file to a tftp server? I've tried "copy start tftp" and copy run tftp". No luck, I get an error message. Thanks in advance.

What kind of error message did you get?
ciscoasa# write net ? WORD IP address of tftp server and file name :. Place IPv6 address within square brackets.

ASA 5505 8.4. How to configure the switch to the backup channel to the primary with a delay (ex., 5 min) using the SLA?

I have ASA 5505 8.4. How to configure the switch to the backup channel to the primary with a delay (for example 5 min.) using the SLA monitor?
Or as something else to implement it?
My configuration for SLA monitor:
sla monitor 123
type echo protocol ipIcmpEcho IP_GATEWAY_MAIN interface outside_cifra
num-packets 3
timeout 3000
frequency 10
sla monitor schedule 123 life forever start-time now
track 1 rtr 123 reachability

Hey cadet alain,
thank you for your answer :-)
I have deleted all such attempts not working, so a packet-trace will be not very useful conent...
Here is the LogLine when i try to browse port 80 from outside (80.xxx.xxx.180:80) without VPN connection:
3
Nov 21 2011
18:29:56
77.xxx.xxx.99
59068
80.xxx.xxx.180
80
TCP access denied by ACL from 77.xxx.xxx.99/59068 to outside:80.xxx.xxx.180/80
The attached file is only the show running-config
Now i can with my AnyConnect Clients, too, but after connection is up, my vpnclients can't surf the web any longer because anyconnect serves as default route on 0.0.0.0 ... that's bad, too
Actually the AnyConnect and Nat/ACL Problem are my last two open Problems until i setup the second ASA on the right ;-)
Regards.
Chris

ASA 5505 VPN with backup route

We are looking to set up a site-to-site VPN with a backup over a T1. We have a remote site with a 1841 router. This router has a PTP T1 back to a secondary location with a 2811. Due to location, the only option we had to get additional bandwidth was to have a cable modem installed. We want to set a site-to-site up to our primary location, with a backup route over the T1 in the event the cable modem goes down. We have an ASA 5505 at the remote location, and an ASA 5540 at the primary. In addition, we want to split the traffic across the two connections. Since the wireless controllers are anchored back to the secondary location, we want to send that traffic over the PTP T1 and the rest of the traffic over the VPN. We also need to have a backup route for the wireless traffic to send across the VPN in the event the T1 goes down.

Go to this link and scroll down to Site to Site VPN (L2L) with IOS and Site to Site VPN (L2L) with ASA, you can use the links example depicting your scenario requirements, where one end is dynamic and other static for Ipsec L2L IOS-to-ASA or ASA-to-IOS.
The best solution obiosly is having static IP addressing, make that clear with your client , but these exmaples are very good solution for your problem.
Keep in mind that the DHCP dynamic side will always be the initiator to bring up the tunnel , not the static side.
http://www.cisco.com/en/US/products/ps6120/prod_configuration_examples_list.html
Regards

ASA 5505 with Backup ISP

I am working with a client that currently has an ASA 5505 with two ISPs for failover using a tracked interface. I would like to configure logging so that the ASA will email us when the Primary ISP goes down and fails over to the backup. Here is what I have so far...
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
switchport access vlan 12
interface Ethernet0/2
speed 100
duplex full
interface Ethernet0/3
switchport access vlan 22
speed 100
duplex full
interface Ethernet0/4
switchport access vlan 22
interface Ethernet0/5
switchport access vlan 22
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 50.76.252.33 255.255.255.248
interface Vlan12
nameif backup
security-level 0
ip address 168.93.174.130 255.255.255.248
interface Vlan22
nameif Phones
security-level 100
ip address 192.168.3.1 255.255.255.0
logging enable
logging buffered warnings
logging asdm warnings
logging from-address [email protected]
logging recipient-address [email protected] level errors
route outside 0.0.0.0 0.0.0.0 DG-Commcast 128 track 1
route backup 0.0.0.0 0.0.0.0 DG-FirstCom 255
sla monitor 123
type echo protocol ipIcmpEcho 73.120.130.1 interface outside
frequency 10
sla monitor schedule 123 life forever start-time now
track 1 rtr 123 reachability
Let me know if you need any more info from the config; it's quite long and not sure what all is needed...
The primary interface is Outside and the backup is obviously Backup
Thanks!
Tony

Hi Tony,
As long as the event covered under 'errors' list - inaddition to the above config, you need to add..
loging mail errors
smtp-server
Check the below link for more information on ASA message logging..
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00805a2e04.shtml
hth
MS

Cisco ASA 5505 Dual-ISP Backup VPN

I am trying to create a backup tunnel from an ASA 5505 to a pix 501 in the case of the Main ISP failing. The Pix external side will stay the same, but not quite sure how I can create a new crypto map and have it use the Backup ISP interface without bringing down the main tunnel.
My first thought was to add the following crypto map to the configuration below:
crypto map outside_map 2 match address outside_1_cryptomap
crypto map outside_map 2 set peer 9.3.21.13
crypto map outside_map 2 set transform-set ESP-DES-MD5
crypto map outside_map interface backupisp -->but this would break the current tunnel.
NYASA# sh run
: Saved
ASA Version 7.2(4)
hostname NYASA
domain-name girls.org
enable password CHwdJ2WMUcjxIIm8 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 10.1.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 9.17.5.8 255.255.255.240
interface Vlan3
description Backup ISP
nameif backupisp
security-level 0
ip address 6.27.9.5 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
switchport access vlan 3
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended permit icmp any any source-quench
access-list outside_access_in extended permit icmp any any unreachable
access-list outside_access_in extended permit icmp any any time-exceeded
access-list outside_access_in extended permit icmp any any
access-list inside_nat0_outbound extended permit ip 10.1.2.0 255.255.255.0 10.1.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.1.2.0 255.255.255.0 10.1.100.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 10.1.2.0 255.255.255.0 10.1.1.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 10.1.2.0 255.255.255.0 10.1.100.0 255.255.255.0
access-list 150 extended permit ip any host 10.1.2.27
access-list 150 extended permit ip host 10.1.2.27 any
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu backupisp 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
global (backupisp) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 9.17.5.7 1 track 1
route backupisp 0.0.0.0 0.0.0.0 6.27.9.1 254
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
aaa authentication ssh console LOCAL
http server enable
http 10.1.2.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sla monitor 10
type echo protocol ipIcmpEcho 4.2.2.2 interface outside
num-packets 3
timeout 1000
frequency 3
sla monitor schedule 10 life forever start-time now
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set peer 9.3.21.13
crypto map outside_map 1 set transform-set ESP-DES-MD5
crypto map outside_map interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption des
hash md5
group 2
lifetime 86400
crypto isakmp nat-traversal 20
track 1 rtr 10 reachability
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 60
console timeout 0
management-access inside
username ptiadmin password BtOLil2gR0VaUjfX encrypted privilege 15
tunnel-group 9.4.21.13 type ipsec-l2l
tunnel-group 9.4.21.13 ipsec-attributes
pre-shared-key *
prompt hostname context
Cryptochecksum:22bb60b07c4c1805b89eb2376683f861
: end
NYASA#
Thanks in advance.

In that case is the PIX who needs two peers (to the ASA).
The ASA will requiere the crypto map to be applied to the backup interface as well (as you mentioned)
crypto map outside_map interface backupisp -->but this would break the current tunnel.
The above command should not break the current tunnel (if the route to reach the other end goes out via the primary interface).
Additionally you need IP SLA configured in the ASA to allow it to use the primary connection and fallback to the backup connection to build-up the tunnel (as well to use again the primary interface when it recovers).
Federico.

Can't Access Internal Servers From Behind An ASA 5505

Hi all.
I am having some trouble accessing some backup Email (Outlook Web Access) and Citrix servers located behind an ASA 5505 firewall at a remote datacentre. Simply put, when I go to the specific URL (e.g. https://citrixdr.xxx.co.uk) I do not arrive at the splash page, I just get a message saying that the server took too long to respond in the web browser. I'm wondering whether I have missed something on the configuraiton or the firewall itself is not letting my requests through.
The remote servers are located at a remote Disaster Recovery site and use the subnet 192.168.4.0/24. I am at head office which is connected to the DR site via a VPN using 192.168.1.0/24.
My running configuration is below, if anyone could have a browse through it it would be much appreciated.
LM-DR-ASA5505# show run
: Saved
ASA Version 8.2(5)
hostname xxx
domain-name xxx.local
enable password 9tc.bMMQOdcEzWlK encrypted
passwd zh5kKKD1zRf47kwr encrypted
names
name 216.82.240.0 MLT1
name 67.219.240.0 MLT2
name 85.158.136.0 MLT3
name 95.131.104.0 MLT4
name 46.226.48.0 MLT5
name 117.120.16.0 MLT6
name 193.109.254.0 MLT7
name 194.106.220.0 MLT8
name 195.245.230.0 MLT9
name 103.3.96.0 MLT10
name xxx.xxx.xxx.xxx citrixdr.xxx.co.uk
name xxx.xxx.xxx.xxx maildr.xxx.co.uk
name xxx.xxx.xxx.xxx webmaildr.xxx.co.uk
name 192.168.4.23 LON-EXCH-03
name 192.168.4.30 Citrix-Access-Gateway
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.4.254 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address xxx.xxx.xxx.xxx 255.255.255.248
ftp mode passive
dns server-group DefaultDNS
domain-name xxx.local
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group service DM-INLINE-SERVICE
service-object icmp
service-object tcp eq www
service-object tcp eq https
object-group network VPN-REMOTE
network-object 192.168.1.0 255.255.255.0
object-group protocol PROTOCOL-LIST
protocol-object ip
protocol-object icmp
protocol-object pim
protocol-object pcp
protocol-object snp
protocol-object udp
protocol-object igmp
protocol-object ipinip
protocol-object gre
protocol-object esp
protocol-object ah
protocol-object tcp
protocol-object eigrp
protocol-object ospf
protocol-object igrp
protocol-object nos
object-group service DM-INLINE-TCP-1 tcp
port-object eq https
port-object eq smtp
object-group service DM-INLINE-TCP-2 tcp
port-object eq www
port-object eq https
object-group network MESSAGE-LABS-TOWERS
network-object MLT1 255.255.240.0
network-object MLT2 255.255.240.0
network-object MLT3 255.255.248.0
network-object MLT4 255.255.248.0
network-object MLT5 255.255.248.0
network-object MLT6 255.255.248.0
network-object MLT7 255.255.254.0
network-object MLT8 255.255.254.0
network-object MLT9 255.255.254.0
network-object MLT10 255.255.252.0
access-list inside-access-in extended permit ip 192.168.4.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside-access-in extended permit ip any any
access-list inside-access-in extended permit ip 192.168.4.0 255.255.255.0 any
access-list inside-access-in extended permit icmp any any
access-list outside-access-in extended permit object-group DM-INLINE-SERVICE any any
access-list outside-access-in extended permit ip 192.168.4.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list outside-access-in extended permit icmp 192.168.4.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list outside-access-in extended permit tcp any host webmaildr.xxx.co.uk object-group DM-INLINE-TCP-2
access-list outside-access-in extended permit tcp any host maildr.xxx.co.uk object-group DM-INLINE-TCP-1
access-list outside-access-in extended permit tcp any host citrixdr.xxx.co.uk eq https
access-list outside-access-in extended permit tcp object-group MESSAGE-LABS-TOWERS host LON-EXCH-03 eq smtp
access-list outside-1-cryptomap extended permit ip 192.168.4.0 255.255.255.0 host xxx.xxx.xxx.xxx
access-list outside-1-cryptomap extended permit ip 192.168.4.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list 101 extended permit ip 192.168.4.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside-nat0-outbound extended permit ip 192.168.4.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list testcap extended permit icmp host 192.168.1.11 host 192.168.4.1
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside-nat0-outbound
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp citrixdr.xxx.co.uk https Citrix-Access-Gateway https netmask 255.255.255.255
static (inside,outside) tcp maildr.xxx.co.uk smtp LON-EXCH-03 smtp netmask 255.255.255.255
static (inside,outside) tcp webmaildr.xxx.co.uk https LON-EXCH-03 https netmask 255.255.255.255
access-group inside-access-in in interface inside
access-group outside-access-in in interface outside
route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
route outside 192.168.1.0 255.255.255.0 xxx.xxx.xxx.xxx 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http xxx.xxx.xxx.xxx 255.255.255.255 outside
http 192.168.4.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside-map 1 match address outside-1-cryptomap
crypto map outside-map 1 set peer xxx.xxx.xxx.xxx
crypto map outside-map 1 set transform-set ESP-3DES-SHA
crypto map outside-map interface outside
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.1.0 255.255.255.0 inside
telnet 192.168.4.0 255.255.255.0 inside
telnet 0.0.0.0 0.0.0.0 inside
telnet xxx.xxx.xxx.xxx 255.255.255.255 outside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh 192.168.4.0 255.255.255.0 inside
ssh xxx.xxx.xxx.xxx 255.255.255.255 outside
ssh xxx.xxx.xxx.xxx 255.255.255.255 outside
ssh xxx.xxx.xxx.xxx 255.255.255.255 outside
ssh timeout 5
ssh version 2
console timeout 0
management-access inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username xxx password LUZB8j2zj03xvSeF encrypted
username xxx password RxEDmrZ7KCRzPu4T encrypted
tunnel-group xxx.xxx.xxx.xxx type ipsec-l2l
tunnel-group xxx.xxx.xxx.xxx ipsec-attributes
pre-shared-key *****
class-map inspection_default
policy-map global_policy
class inspection_default
inspect icmp
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:61e54b16fb87f1e6fa3b8d520e87ddc0
: end

Hi Jouni, thanks for your response.
Turns out that the Citrix Access Gateway wasn't set up until yesterday evening and by then I had stopped trying for the day. It is now set up and external access is available.
Further to this, my colleague forgot to inform me of the change of I.P. address of the Exchange server. This meant that Webmail requests were pointing to an I.P. address that didn't exist.
I have reconfigured the firewall this morning and external access for Webmail is also working correctly.

ASA 5505 - 2 Internet Connections, Problems with the Default Route

Hey there,
i have a Problem at a Customer Site at the moment. The customer uses an ASA 5505 with two internet connections attached to it. On the first connection (which is the only one in use at the moment) he has some Static-PAT's from Outside to Inside where he translates different services to the internal servers. He also has a site-2-site VPN terminating there and AnyConnect.
He now wants to switch the Internet Traffic from Inside to the new Internet Connection. Therefore changing the default route to that new ISPs Gateway. The problem now is, that no traffic recieved on the old "outside" Interface is transmitted back out of that old "outside" Interface. And this happens although the "same-security permit intra-interface" command is set.
Can you tell me what's wrong here? For every Static-PAT from outside to inside there is also a dynamic PAT from inside to outside. But the ASA seems to ignore this. I have not looked into the Logs yet, was too busy finding the problem because i had no real time window to test on the productive ASA.
Can it be achieved in any way? Having a default route on the ASA which leads any traffic to the second internet connection while still having connections on the first internet connection where no explicit route can be set? Because connections arrive from random IPs?
Many thanks for your help in advance!
Steffen

Phillip, indeed , I have as well read may comments,it all depends on your environment as they all differ from one another, you best bet is to have a good solid plan for upgrade and fall back. You do have a justification to upgrade for features needed, so I would suggest the following:
1- Do a search again in forum for ASA code upgrades and look at comments from users that have gone through this process and note their impact in fuctionality if any. I believe this is good resource to collect information .
2- Very important , look into release notes for a particular version. For example version 8.0, look into open CAVEATS usually at the end of the link page, reading the open bugs gives you clues what has not yet been resolved for that particular code and if in fact could impact you in your environment, it is possible that a particular bug does not realy apply to your environment becuase you have yet not implemented that particualr configuration. Usually we all try to aim towards a GD (General Deployment) code which is what we all understand is most stable but not necesarily means you have to be stack in that code waiting for another GD release, in my personal experience I have upgraded our firewall from 7.2 to 8.0(3) long ago and had no issues, and recently upgraded to 8.0(4)when it was first release in August this year.
Release notes
http://www.cisco.com/en/US/products/ps6120/prod_release_notes_list.html
3- AS a good practice precaution -
a-Backup firewall configs in clear text as well as via tftp code.
b-Backup running code and ASDM version code currently running in firewall.
c- Save the output of " show version " to have as reference for all the feature licenses you currently have running as asll as activation keys - good info to have to compare with after upgrade.
d- Ensure that the code you will be using to upgrade also uses correct ASDM version code.
I think with thorough assesment and preparation you can indeed minimize impact.
Rgds
Jorge

ASA 5505, error in Access Rule

Hello.
Tha ASA 5505 is working, but I try to allow http and https from internet to a server running 2012 Essentials. The server has the internal IP 192.168.0.100. I have created an Object called SERVER with IP 192.168.0.100
The outside Interface is called ICE
I have configured NAT:
I have also configured Access Rules:
But when I test it With the Packet Tracer I get an error:
Whats wrong With the Access Rule?
I do prefer the ASDM :)
Best regards Andreas

Hello Jeevak.
This is the running config (Vlan 13 (Interface ICE) is the one in use:
domain-name DOMAIN.local
names
name 192.168.0.150 Server1 description SBS 2003 Server
name 192.168.10.10 IP_ICE
name x.x.x.0 outside-network
name x.x.x.7 IP_outside
name 192.168.0.100 SERVER description Hovedserver
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.1 255.255.255.0
interface Vlan2
description Direct Connect
backup interface Vlan13
nameif outside
security-level 0
pppoe client vpdn group PPPoE_DirectConnect
ip address pppoe
interface Vlan3
description Gjestenettet
nameif dmz
security-level 50
ip address 10.0.0.1 255.255.255.0
interface Vlan13
description Backupnett ICE
nameif ICE
security-level 0
ip address IP_ICE 255.255.255.0
interface Vlan23
description
nameif USER
security-level 50
ip address 10.1.1.1 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
switchport access vlan 13
interface Ethernet0/2
switchport access vlan 23
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
switchport access vlan 3
interface Ethernet0/7
switchport access vlan 3
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
dns domain-lookup dmz
dns server-group DefaultDNS
domain-name DOMAIN.local
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
access-list outside_access_in extended permit tcp any host IP_outside eq https
access-list outside_access_in extended permit tcp any host IP_outside eq www
access-list outside_access_in extended permit icmp any host IP_outside echo-reply
access-list outside_access_in remark For RWW
access-list outside_access_in remark For RWW
access-list outside_access_in remark For RWW
access-list outside_access_in remark For RWW
access-list outside_access_in remark For RWW
access-list outside_access_in remark For RWW
access-list outside_access_in remark For RWW
access-list outside_access_in remark For RWW
access-list outside_access_in remark For RWW
access-list outside_access_in remark For RWW
access-list outside_access_in remark For RWW
access-list outside_access_in remark For RWW
access-list DOMAINVPN_splitTunnelAcl standard permit any
access-list inside_nat0_outbound extended permit ip any 192.168.0.192 255.255.255.192
access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 192.168.0.192 255.255.255.192
access-list DOMAIN_VPN_splitTunnelAcl standard permit 192.168.0.0 255.255.255.0
access-list ICE_access_in extended permit tcp any host IP_ICE eq https
access-list ICE_access_in extended permit tcp any host IP_ICE eq www
access-list ICE_access_in extended permit icmp any host IP_ICE echo-reply
access-list ICE_access_in remark For RWW
access-list ICE_access_in remark For RWW
access-list USER_access_in extended permit ip any any
pager lines 24
logging enable
logging asdm warnings
mtu inside 1500
mtu outside 1500
mtu dmz 1500
mtu ICE 1500
mtu USER 1500
ip local pool VPNPool 192.168.10.210-192.168.10.225 mask 255.255.255.0
no failover
monitor-interface inside
monitor-interface outside
monitor-interface dmz
monitor-interface ICE
monitor-interface USER
icmp unreachable rate-limit 1 burst-size 1
icmp permit outside-network 255.255.255.0 outside
icmp permit 192.168.10.0 255.255.255.0 ICE
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
global (ICE) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
nat (dmz) 1 10.0.0.0 255.255.255.0
nat (USER) 1 10.1.1.0 255.255.255.0
static (inside,ICE) tcp interface www SERVER www netmask 255.255.255.255
static (inside,outside) tcp interface www SERVER www netmask 255.255.255.255
static (inside,ICE) tcp interface https SERVER https netmask 255.255.255.255
static (inside,outside) tcp interface https SERVER https netmask 255.255.255.255
access-group outside_access_in in interface outside
access-group ICE_access_in in interface ICE
access-group USER_access_in in interface USER
route outside 0.0.0.0 0.0.0.0 x.x.x.1 1 track 123
route ICE 0.0.0.0 0.0.0.0 192.168.10.1 254
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable
http 192.168.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sla monitor 1
type echo protocol ipIcmpEcho x.x.x.1 interface outside
num-packets 3
frequency 10
sla monitor schedule 1 life forever start-time now
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs group1
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 40 set pfs group1
crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
track 123 rtr 1 reachability
no vpn-addr-assign local
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd auto_config outside
dhcpd address 10.0.0.10-10.0.0.39 dmz
dhcpd dns y.y.y.2 z.z.z.z interface dmz
dhcpd lease 6000 interface dmz
dhcpd enable dmz
dhcpd address 10.1.1.100-10.1.1.120 USER
dhcpd dns y.y.y.2 z.z.z.z interface USER
dhcpd lease 6000 interface USER
dhcpd domain USER interface USER
dhcpd enable USER
ntp server 64.0.0.2 source outside
group-policy DOMAIN_VPN internal
group-policy DOMAIN_VPN attributes
dns-server value 192.168.0.150
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value DOMAIN_VPN_splitTunnelAcl
default-domain value DOMAIN.local
class-map inspection_default
match default-inspection-traffic
class-map imblock
match any
class-map P2P
match port tcp eq www
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map type inspect im impolicy
parameters
match protocol msn-im yahoo-im
drop-connection log
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect pptp
policy-map type inspect http P2P_HTTP
parameters
match request uri regex _default_gator
drop-connection log
match request uri regex _default_x-kazaa-network
drop-connection log
match request uri regex _default_msn-messenger
drop-connection log
match request uri regex _default_gnu-http-tunnel_arg
drop-connection log
policy-map IM_P2P
class imblock
inspect im impolicy
class P2P
inspect http P2P_HTTP
service-policy global_policy global
service-policy IM_P2P interface inside
prompt hostname context
: end
asdm image disk0:/asdm-524.bin
asdm location Server1 255.255.255.255 inside
asdm location IP_ICE 255.255.255.255 inside
asdm location outside-network 255.255.255.0 inside
asdm location SERVER 255.255.255.255 inside
no asdm history enable
What is wrong? Everything Works well except port forwarding.
Andreas

ASA 5505 IPSEC VPN connected but can't access to LAN

ASA : 8.2.5
ASDM: 6.4.5
LAN: 10.1.0.0/22
VPN Pool: 172.16.10.0/24
Hi, we purcahsed a new ASA 5505 and try to setup IPSEC VPN via ASDM; i just simply run the Wizards, setup vpnpool, split tunnelling,etc.
I can connect to the ASA by using cisco VPN client and internet works fine on the local PC, but it cannot access to the LAN (can't ping. can't remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile i created worked fine.
Below is my configure, do I mis-configure anything?
ASA Version 8.2(5)
hostname asatest
domain-name XXX.com
enable password 8Fw1QFqthX2n4uD3 encrypted
passwd g9NiG6oUPjkYrHNt encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.1.1.253 255.255.252.0
interface Vlan2
nameif outside
security-level 0
ip address XXX.XXX.XXX.XXX 255.255.255.240
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
dns server-group DefaultDNS
domain-name vff.com
access-list vpntest_splitTunnelAcl standard permit 10.1.0.0 255.255.252.0
access-list inside_nat0_outbound extended permit ip 10.1.0.0 255.255.252.0 172.16.10.0 255.255.255.0
pager lines 24
logging enable
logging timestamp
logging trap warnings
logging asdm informational
logging device-id hostname
logging host inside 10.1.1.230
mtu inside 1500
mtu outside 1500
ip local pool vpnpool 172.16.10.1-172.16.10.254 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server AD protocol nt
aaa-server AD (inside) host 10.1.1.108
nt-auth-domain-controller 10.1.1.108
http server enable
http 10.1.0.0 255.255.252.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 10.1.0.0 255.255.252.0 inside
ssh timeout 20
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy vpntest internal
group-policy vpntest attributes
wins-server value 10.1.1.108
dns-server value 10.1.1.108
vpn-tunnel-protocol IPSec l2tp-ipsec
password-storage disable
ip-comp disable
re-xauth disable
pfs disable
ipsec-udp disable
ipsec-udp-port 10000
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpntest_splitTunnelAcl
default-domain value XXX.com
split-tunnel-all-dns disable
backup-servers keep-client-config
address-pools value vpnpool
username admin password WeiepwREwT66BhE9 encrypted privilege 15
username user5 password yIWniWfceAUz1sUb encrypted privilege 5
username user3 password umNHhJnO7McrLxNQ encrypted privilege 3
tunnel-group vpntest type remote-access
tunnel-group vpntest general-attributes
address-pool vpnpool
authentication-server-group AD
authentication-server-group (inside) AD
default-group-policy vpntest
strip-realm
tunnel-group vpntest ipsec-attributes
pre-shared-key BEKey123456
peer-id-validate nocheck
privilege cmd level 3 mode exec command perfmon
privilege cmd level 3 mode exec command ping
privilege cmd level 3 mode exec command who
privilege cmd level 3 mode exec command logging
privilege cmd level 3 mode exec command failover
privilege cmd level 3 mode exec command packet-tracer
privilege show level 5 mode exec command import
privilege show level 5 mode exec command running-config
privilege show level 3 mode exec command reload
privilege show level 3 mode exec command mode
privilege show level 3 mode exec command firewall
privilege show level 3 mode exec command asp
privilege show level 3 mode exec command cpu
privilege show level 3 mode exec command interface
privilege show level 3 mode exec command clock
privilege show level 3 mode exec command dns-hosts
privilege show level 3 mode exec command access-list
privilege show level 3 mode exec command logging
privilege show level 3 mode exec command vlan
privilege show level 3 mode exec command ip
privilege show level 3 mode exec command ipv6
privilege show level 3 mode exec command failover
privilege show level 3 mode exec command asdm
privilege show level 3 mode exec command arp
privilege show level 3 mode exec command route
privilege show level 3 mode exec command ospf
privilege show level 3 mode exec command aaa-server
privilege show level 3 mode exec command aaa
privilege show level 3 mode exec command eigrp
privilege show level 3 mode exec command crypto
privilege show level 3 mode exec command vpn-sessiondb
privilege show level 3 mode exec command ssh
privilege show level 3 mode exec command dhcpd
privilege show level 3 mode exec command vpnclient
privilege show level 3 mode exec command vpn
privilege show level 3 mode exec command blocks
privilege show level 3 mode exec command wccp
privilege show level 3 mode exec command dynamic-filter
privilege show level 3 mode exec command webvpn
privilege show level 3 mode exec command module
privilege show level 3 mode exec command uauth
privilege show level 3 mode exec command compression
privilege show level 3 mode configure command interface
privilege show level 3 mode configure command clock
privilege show level 3 mode configure command access-list
privilege show level 3 mode configure command logging
privilege show level 3 mode configure command ip
privilege show level 3 mode configure command failover
privilege show level 5 mode configure command asdm
privilege show level 3 mode configure command arp
privilege show level 3 mode configure command route
privilege show level 3 mode configure command aaa-server
privilege show level 3 mode configure command aaa
privilege show level 3 mode configure command crypto
privilege show level 3 mode configure command ssh
privilege show level 3 mode configure command dhcpd
privilege show level 5 mode configure command privilege
privilege clear level 3 mode exec command dns-hosts
privilege clear level 3 mode exec command logging
privilege clear level 3 mode exec command arp
privilege clear level 3 mode exec command aaa-server
privilege clear level 3 mode exec command crypto
privilege clear level 3 mode exec command dynamic-filter
privilege cmd level 3 mode configure command failover
privilege clear level 3 mode configure command logging
privilege clear level 3 mode configure command arp
privilege clear level 3 mode configure command crypto
privilege clear level 3 mode configure command aaa-server
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4
: end

I change a Machine's gateway to this ASA and capture again, now we can see some reply.
All ohter PCs and switches gateway are point to another ASA, maybe that's the reason why i didn't work?
what's the recommanded way to make our LAN to have two 2 gateways(for load balance or backup router, etc)?
add two gateways to all PCs and swtichwes?
1: 18:15:48.307875 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   2: 18:15:49.777685 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   3: 18:15:51.377147 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   4: 18:15:57.445777 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   5: 18:15:58.856324 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   6: 18:16:00.395090 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   7: 18:16:06.483464 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   8: 18:16:08.082805 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   9: 18:16:09.542406 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
10: 18:16:20.640424 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
11: 18:16:20.642193 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
12: 18:16:21.169607 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
13: 18:16:21.171210 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
14: 18:16:22.179556 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
15: 18:16:22.181142 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
16: 18:16:23.237673 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
17: 18:16:23.239291 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
18: 18:16:27.676402 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
19: 18:16:29.246935 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
20: 18:16:30.676921 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
21: 18:16:49.539660 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
22: 18:16:54.952602 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
23: 18:17:04.511463 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request

LAN Failover in ASA 5505

I have two web server and I want to configure ASA 5505 in such a way that it forward all incoming request to ServerA. In case if ServerA is down or failed ASA 5505 automatically forward all incoming request to ServerB.
I am new to ASA 5505.
Thanks in advance.

You can do that if the web server are in two different subnet. So one web server is on a interface and the other web server is on other interface. You must configure ip sla as below :
interface Ethernet0/0.1239
vlan 1239
nameif OUTSIDE
security-level 0
ip address 94.125.239.251 255.255.255.0
interface Ethernet0/0.1240
vlan 1240
nameif OUTSIDE-BACKUP
security-level 0
ip address 94.138.42.43 255.255.255.248
route OUTSIDE 0.0.0.0 0.0.0.0 94.125.239.252 1 track 1
route OUTSIDE-BACKUP 0.0.0.0 0.0.0.0 94.138.42.41 254
sla monitor 123
type echo protocol ipIcmpEcho 8.8.8.8 interface OUTSIDE
num-packets 3
frequency 10
sla monitor schedule 123 life forever start-time now
track 1 rtr 123 reachability
For the web server A if is down, you must check it with a script that is executing on a server in the same subnet of web server A

ASA 5505 unable to connect inside or outside

Hello,
I'm extremely new to router configurations, and am attempting to configure a backup ASA 5505 to use as a temporary access point in the event that our main ASA becomes unavailable. What I have done is loaded the running config from our main ASA onto the backup, and have made changes to necessary routes, IPs, etc. I can connect to it from a remote computer without problem, but I cannot access any of our servers, nor can I access the internet. I have also tried modifying the access list and NAT rules every which way from Sunday, but I still cannot get this thing to allow any information through. I keep getting "failed to locate egress interface for UDP from outside" errors.
We are using Cisco AnyConnect to connect , and mind you, since the config for this backup ASA was taken from our main, it still has the original certificate info and profiles. I was told that this wouldn't matter, but I thought I should mention in case I need to remove any of it from the config.
Here is part of the config file. I took out some information, but tried to keep it understandable. If anyone could point me in the right direction, it would be greatly appreciated!
ciscoasa# show running-config
: Saved
: Serial Number: xxxxxxxxxxx
: Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz
ASA Version 9.2(2)
hostname ciscoasa
domain-name domain
enable password encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd encrypted
names
ip local pool pool1 x.x.9.22-x.x.9.254 mask 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address x.x.8.10 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address x.x.x.237 255.255.255.248
boot system disk0:/asa922-k8.bin
boot config disk0:/startup-config
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group Default
name-server x.x.8.100
domain-name domain
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network pool1
subnet x.x.9.0 255.255.255.0
object network outside-network
host x.x.x.237
object network Remote-Network
subnet x.x.8.0 255.255.255.0
object network local
object network obj-x.x.9.24
host x.x.9.24
object-group network Outside-Network-Group
description Outside Network Group
network-object x.x.x.232 255.255.255.248
object-group network Inside-Network-Group
description Inside Network Group
network-object x.x.8.0 255.255.255.0
access-list inside_access_in extended permit icmp any any
access-list inside_access_in extended permit ip any any
access-list NONAT extended permit ip x.x.8.0 255.255.255.0 x.x.9.0 255.255.255.0
pager lines 24
logging enable
logging buffer-size 30000
logging buffered debugging
logging asdm informational
no logging message 106015
no logging message 313001
no logging message 313008
no logging message 106023
no logging message 710003
no logging message 106100
no logging message 302015
no logging message 302014
no logging message 302013
no logging message 302018
no logging message 302017
no logging message 302016
no logging message 302021
no logging message 302020
flow-export destination inside x.x.8.132 2055
flow-export template timeout-rate 1
flow-export delay flow-create 50
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
asdm image disk0:/asdm-722.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static any any destination static pool1 pool1 no-proxy-arp route-lookup
nat (inside,outside) source static any any destination static Remote-Network Remote-Network no-proxy-arp route-lookup
nat (outside,outside) source dynamic pool1 interface
object network obj_any
nat (inside,outside) dynamic interface
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 x.x.x.232 1
route inside x.x.11.0 255.255.255.0 x.x.11.1 1
If you have any questions, or need any other information, please let me know.
Thanks!

Am I posting this in the wrong section? Anyone?

Vpn-asa 5505 - connects fine, can't use resources

Using Remote Client VPN to access internal Lan behind an ASA 5505 device. The connection is working fine. But once I connect, I can't access any computer shared folders etc.   The only thing I can do is access the ASA 5505 through the ASDM 7.1    I can only ping the device 10.0.0.1 but nothing else.    The funny thing is that this was working fine, then in an attempt to speed up the VPN ACCESS (it is pretty slow), I went into the ASDM configuration software to look around.   Didn't think I changed anything, but now, it's not working.   Here is a copy of the backup cpg.
Any ideas.   Please respond with ASDM COMMANDS.. I'm a novice at the command line stuff.
Thanks.
-brett
config:
: Saved
: Written by enable_15 at 09:19:26.379 UTC Sat Feb 15 2014
ASA Version 9.1(4)
hostname ciscoasa
domain-name hnedu.com
enable password mnpTCRVkk1.ZjiWJ encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd 2KFQnbNIdI.2KYOU encrypted
names
ip local pool VPNUsers 10.0.0.80-10.0.0.99 mask 255.255.0.0
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
speed 100
duplex full
interface Ethernet0/2
speed 100
duplex full
interface Ethernet0/3
speed 100
duplex full
interface Ethernet0/4
speed 100
duplex full
interface Ethernet0/5
speed 100
duplex full
interface Ethernet0/6
speed 100
duplex full
interface Ethernet0/7
speed 100
duplex full
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.0.0
interface Vlan2
description External Connection
no forward interface Vlan1
nameif outside
security-level 0
ip address 209.117.123.226 255.255.255.224
boot system disk0:/asa914-k8.bin
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server 10.0.0.2
name-server 10.0.0.4
domain-name hnedu.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network obj-10.0.0.0
subnet 10.0.0.0 255.255.0.0
object network obj-10.0.0.64
subnet 10.0.0.64 255.255.255.192
object network obj-10.0.0.6
host 10.0.0.6
object network obj-10.0.3.48
host 10.0.3.48
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network NETWORK_OBJ_10.0.0.64_26
subnet 10.0.0.64 255.255.255.192
object-group network RDP_static
object-group service RemoteDesktop tcp-udp
description Windows Remote Desktop Access
port-object eq 3389
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
access-list inside_access_in extended permit ip any4 any4
access-list Napoleons_splitTunnelAcl standard permit 10.0.0.0 255.255.0.0
access-list inside_nat0_outbound extended permit ip 10.0.0.0 255.255.0.0 10.0.0.64 255.255.255.192
access-list outside_access_in extended permit tcp any4 host 10.0.0.6 eq www
access-list outside_access_in remark remote desktop to cproom desktop
access-list outside_access_in extended permit object-group TCPUDP any4 host 10.0.3.48 eq 3389
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-715-100.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,any) source static obj-10.0.0.0 obj-10.0.0.0 destination static obj-10.0.0.64 obj-10.0.0.64 no-proxy-arp route-lookup
object network obj-10.0.0.6
nat (inside,outside) static 209.117.123.227
object network obj-10.0.3.48
nat (inside,outside) static 209.117.123.228
object network obj_any
nat (inside,outside) dynamic interface
access-group inside_access_in in interface inside control-plane
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 209.117.123.225 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 10.0.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association pmtu-aging infinite
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto ca trustpool policy
crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
    308205ec 308204d4 a0030201 0202106e cc7aa5a7 032009b8 cebcf4e9 52d49130
    0d06092a 864886f7 0d010105 05003081 ca310b30 09060355 04061302 55533117
    30150603 55040a13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
    13165665 72695369 676e2054 72757374 204e6574 776f726b 313a3038 06035504
    0b133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
    20617574 686f7269 7a656420 75736520 6f6e6c79 31453043 06035504 03133c56
    65726953 69676e20 436c6173 73203320 5075626c 69632050 72696d61 72792043
    65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
    30303230 38303030 3030305a 170d3230 30323037 32333539 35395a30 81b5310b
    30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
    496e632e 311f301d 06035504 0b131656 65726953 69676e20 54727573 74204e65
    74776f72 6b313b30 39060355 040b1332 5465726d 73206f66 20757365 20617420
    68747470 733a2f2f 7777772e 76657269 7369676e 2e636f6d 2f727061 20286329
    3130312f 302d0603 55040313 26566572 69536967 6e20436c 61737320 33205365
    63757265 20536572 76657220 4341202d 20473330 82012230 0d06092a 864886f7
    0d010101 05000382 010f0030 82010a02 82010100 b187841f c20c45f5 bcab2597
    a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
    9c688b2e 957b899b 13cae234 34c1f35b f3497b62 83488174 d188786c 0253f9bc
    7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
    15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
    63cd1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8
    18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
    4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
    81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 02030100 01a38201 df308201
    db303406 082b0601 05050701 01042830 26302406 082b0601 05050730 01861868
    7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1d130101
    ff040830 060101ff 02010030 70060355 1d200469 30673065 060b6086 480186f8
    45010717 03305630 2806082b 06010505 07020116 1c687474 70733a2f 2f777777
    2e766572 69736967 6e2e636f 6d2f6370 73302a06 082b0601 05050702 02301e1a
    1c687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
    03551d1f 042d302b 3029a027 a0258623 68747470 3a2f2f63 726c2e76 65726973
    69676e2e 636f6d2f 70636133 2d67352e 63726c30 0e060355 1d0f0101 ff040403
    02010630 6d06082b 06010505 07010c04 61305fa1 5da05b30 59305730 55160969
    6d616765 2f676966 3021301f 30070605 2b0e0302 1a04148f e5d31a86 ac8d8e6b
    c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
    69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
    1b311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301d0603
    551d0e04 1604140d 445c1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355
    1d230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300d0609
    2a864886 f70d0101 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80
    4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
    b2227055 d9203340 3307c265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
    6decd018 7d494aca 99c71928 a2bed877 24f78526 866d8705 404167d1 273aeddc
    481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
    b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
    5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
    6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
    6c2527b9 deb78458 c61f381e a4c4cb66
quit
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
management-access inside
vpn-addr-assign local reuse-delay 5
vpn-sessiondb max-other-vpn-limit 10
vpn-sessiondb max-anyconnect-premium-or-essentials-limit 2
dhcp-client update dns server none
dhcpd dns 10.0.0.2 10.0.0.4
dhcpd wins 10.0.0.2 10.0.0.4
dhcpd domain hnedu.com
dhcpd option 5 ip 10.0.0.2 10.0.0.4 interface inside
dhcpd option 6 ip 10.0.0.2 10.0.0.2 interface inside
dhcprelay server 10.0.0.2 inside
dhcprelay server 10.0.0.4 inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol ikev1 ikev2 ssl-clientless
group-policy Napoleons internal
group-policy Napoleons attributes
wins-server value 10.0.0.2 10.0.0.4
dns-server value 10.0.0.2 10.0.0.4
vpn-tunnel-protocol ikev1 l2tp-ipsec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Napoleons_splitTunnelAcl
default-domain value hnedu.com
group-policy Napoleon internal
group-policy Napoleon attributes
wins-server value 10.0.0.2 10.0.0.4
dns-server value 10.0.0.2 10.0.0.4
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Napoleons_splitTunnelAcl
default-domain value hnedu.com
username bpenza password LTg/b/c3kPWfC8KM encrypted privilege 0
username bpenza attributes
vpn-group-policy Napoleons
username baudette password nPZIRfshkE7WcaDQ encrypted
username baudette attributes
vpn-group-policy Napoleons
tunnel-group Napoleons type remote-access
tunnel-group Napoleons general-attributes
address-pool VPNUsers
default-group-policy Napoleons
tunnel-group Napoleons ipsec-attributes
ikev1 pre-shared-key Holyname12
tunnel-group Napoleon type remote-access
tunnel-group Napoleon general-attributes
address-pool VPNUsers
default-group-policy Napoleon
tunnel-group Napoleon ipsec-attributes
ikev1 pre-shared-key Holyname12
policy-map global-policy
class class-default
user-statistics accounting
service-policy global-policy global
prompt hostname context
call-home reporting anonymous
Cryptochecksum:eb9d34735b125eb61d8f7d93247ad9b7
: end

You need to discuss this issue with your network administrator. I suspect the network ports that allow VPN access to the system you want to use may be closed.
You also need to confirm that the VPN software you are using is compatible with the network you are trying to access. Where I work, the VPN software that comes with Mac OS X is not
compatible with the network so I have to use VPN software that was provided by my employer. You might be in the same situation.

ASA 5505 Backup

Similar Messages

Maybe you are looking for