ASA 5505 can't configured it, no access inside to box
Device is ASA 5505 with software version 7.2. Very bad problems: When i try access to ASA try conficuring it, i can't access to box inside. First time i get connect this ASAs configurationsofware and change password and restart it and now i can't access to box inside. ASDM notes: No found device or something else.
NOTICE!
And i can't reset a box to "factory default" because reset-button is reserved for future use?
I try connect to ASA 5505 with Ethernetcable (ports 0, 1, 2...7) and
Seroal communicateport with command line and telnet but not response?
Is this new one ASA 5505 broken when it left your factorys?
HOW can i connect to ASA 5505 and configure it now? I need Factory default reset but how it happens, because can't acces to box?
Regards
Okay, thanks. I set these parameters com ports, but still not working.
I try connect with consoleport/terminal and with network cable port 0 - 7, but no connection, only note not found and Time session over or something else ):
This Cisco's ASDM not even found this ASA 5505. I have bad feeling it is broken or jummed or some softwarebug what locked the box every ports (ethernet and console).
I wonder, why this bos have RESET-button, but it is reserved for future use. Now when user need it so bad. And ofcourse usb-ports are future use.
FINAL QUESTION:
Where and how i can reset this ASA? Is it only way to change it my dealer a new one which working well like its designed.
Similar Messages
-
ASA 5505 version 9.1 in extended access-list I can add interface name as destination??
Hi All,
I'm adding extended ACL on the ASA 5505 version 9.1 and found that in the source or destination field I can specify interface name instead of object, host/network but can't find it documented anywhere and what is the behavior of that?
access-list VOICE_IN extended permit ip object obj-VOICE-LAN interface OUTSIDE
Is it matching the egress interface or what?Use the interface name rather than IP address to match traffic based
on which interface is the source or destination of the traffic. You must
specify the interface keyword instead of specifying the actual IP
address in the ACL when the traffic source is a device interface. For
example, you can use this option to block certain remote IP addresses
from initiating a VPN session to the ASA by blocking ISAKMP. Any
traffic originated from or destined to the ASA, itself, requires that you
use the access-group command with the control-plane keyword. -
Cisco ASA 5505 can ping gateway but can't ping internet
Good day to all!
Sorry if I post this on the wrong group, I am having a bit of a problem on configuring an ASA 5505 firewall. And I scoured google but can't seem to find a specific link to my issues.
It is on a routed mode, have successfully configured inside and outside vlans. Hosts inside vlan can ping each other. Hosts on outside vlan can also ping each other. Problem is, when I am pinging 8.8.8.8, I received ????? Please see config below.
Any help greatly appreciated.
TIA!
: Saved
ASA Version 8.4(3)
hostname ciscoasan
enable password bD3fGYMFeJJTATOJ encrypted
passwd 2KF1w9ErdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
description INSIDE
nameif inside
security-level 100
ip address 10.10.10.2 255.255.255.0
interface Vlan2
description OUTSIDE
nameif outside
security-level 0
ip address 203.127.68.2 255.255.255.240
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
access-list outside_access_in extended permit ip any any
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
object network obj_any
nat (inside,outside) dynamic interface
nat (inside,outside) after-auto source dynamic any interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 203.127.68.1 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
http server enable
http 10.10.10.0 255.255.255.0 inside
http authentication-certificate inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh 10.10.10.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
anyconnect-essentials
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:6b3e0ce99eda3d2563cf9f392f8001b7
: endHi badingdong,
Remove these lines:
no nat (inside,outside) after-auto source dynamic any interface
no access-group outside_access_in in interface outside
If you have more inside subnets need access to internet, please make sure that you have a static route in place as shown below.
route inside 10.0.0.0 255.0.0.0 10.10.10.1
Also make sure that you have a correct DNS server is assigned on your internal hosts.
Thanks
Rizwan Rafeek -
ASA 5505 -Can I use outside dynamic IP for webserver DMZ?
SETUP
ASA 5505
ASA Version 9.1(2)
ASDM Version 7.1(3)
I have basic license, using only three vlans (outside, inside, DMZ).
QUESTION:
I want to find a way (if possible) to use the single DYNAMIC IP (dhcp'd from ISP) on the "outside" interface, as a means to setup a web-server on the DMZ? I just want to allow my WHS-2011 (server) to talk to microsoft's free DDNS service where my domain name is hosted (ports 80,443,4125).
So far, every setup option I have tried does not make it past the implicit deny acl's (on the outside interface) to the web-server (DMZ).
I understand that the VLAN1 (inside) had to be disabled. I understand that objects now replace some of the older NAT'd components.
CONFIG:
object network webserver-external-ip
host <X.X.X.X>
! I had set this to match my ISP DHCP address
object network webserver
host 172.16.0.2
nat (DMZ,outside) static webserver-external-ip service tcp www www
nat (DMZ,outside) static webserver-external-ip service tcp 443 443
nat (DMZ,outside) static webserver-external-ip service tcp 4125 4125
access-list outside_acl extended permit tcp any object webserver eq www
access-list outside_acl_https extended permit tcp any object webserver eq 443
access-list outside_acl_rww extended permit tcp any object webserver eq 4125
access-group outside_acl in interface outside
access-group outside_acl_https in interface outside
access-group outside_acl_rww in interface outside
! added the dns statements below because the cisco doc (below) says it's required or dmz traffic can't get out despite default rule allowing it to do so.
! (ctrl-F) ... "all traffic would be blocked from the dmz to hosts on the internet"
! http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080bf150c.shtml
object network dns-server
host 8.8.8.8
exit
access-list dmz_acl extended permit udp any object dns-server eq domain
access-list dmz_acl extended permit ip any any
access-group dmz_acl in interface DMZ
SUMMARY:
I just want to allow my WHS-2011 (server) to talk to microsoft's free DDNS service where my domain name is hosted (ports 80,443,4125).
I want to find a way (if possible) to use the single DYNAMIC IP (dhcp'd from ISP) on the "outside" interface, as a means to setup a web-server on the DMZ?
Other:
As an interim alternative, I have been able to setup & connect to the ASA using clientless vpn (web-ssl), and from there getting over to my WHS2011 server...-but the problem is, I have no way of knowing, or updating my DDNS once that IP changes since the ASA keeps blocking the return traffic to theh outside interface. My only assumption is that becasue I am using a single dynamic IP (outside interface) that it has nothing to re-direct the traffic to....???
Thank You for any help you can provide!!
k/rHi,
I cant really help with the DDNS portion but I would imagine you already have that sorted out.
The ASA configurations however seem a bit off to me.
Here is what you should configure
STATIC PAT TO HOST SERVICES
There are some changes that need to be done to both ACL and NAT configurations. First of the NAT configurations for each port require their own "object network" to be configured.
Also since you are using a DHCP address from the ISP to act as the NAT address then you can use the keyword/parameter "interface" in the actual "nat" command. This basically tells the ASA that it should use whatever IP address is currently on the "outside" interface of the ASA. So you wont have to configure any separate "object network" for the public IP address every time it changes.
Also, with regards to the ACL configurations. You should only configure one ACL per interface in the "in" direction. So all the rules you need to configure for traffic inbound from the Internet need to be in the same ACL that you then attach to the "outside" interface with the command "access-group"
object network WEBSERVER-TCP80
host 172.16.0.2
nat (DMZ,outside) static interface service tcp www www
object network WEBSERVER-TCP443
host 172.16.0.2
nat (DMZ,outside) static interface service tcp 443 443
object network WEBSERVER-TCP4125
host 172.16.0.2
nat (DMZ,outside) static interface service tcp 4125 4125
access-list outside_acl extended permit tcp any object WEBSERVER-TCP80 eq www
access-list outside_acl extended permit tcp any object WEBSERVER-TCP443 eq https
access-list outside_acl extended permit tcp any object WEBSERVER-TCP4125 eq 4125
access-group outside_acl in interface outside
DYNAMIC PAT FOR LANs and DMZs
The above NAT configurations only handles the NAT for situations where the remote hosts on the Internet contact your DMZ server.
If you want to configure Dynamic PAT for all your LAN and DMZ users which basically enable them to use the "outside" interface public IP address for Internet traffic, then you could configure this single "nat" configuration
nat (any,outside) after-auto source dynamic any interface
This would enable Dynamic PAT for all users behind the ASA
I am not sure if you will run into problems since you are using a single public IP address and trying to forward TCP/443. This port is both used for SSL VPN and ASDM management of the ASA.
If you want to change the default port of the ASDM management you can use this command
http server enable
If you want to change the default port of SSL VPN you can use these commands
webvpn
port
Naturally before doing either of the above changes, make sure that you are not relying to them for management purposes if something was to go wrong. If you have SSH management access to the ASA then it should naturally be ok.
I am not sure if all of the above are enough to get your setup working but it should be the basics. Naturally if there is still problems after the above suggestions it might be helpfull to see the current ASA configurations. For example NAT might not work if the ordering of NAT rules is wrong even though the actual configurations are otherwise valid.
Hope this helps
Please do remember to mark a reply as the correct answer if it answered your question.
Feel free to ask more if needed
- Jouni -
Cisco ASA 5505 - Can't Login from Public & Local IP Anymore!
Hello,
We've a Cisco ASA 5505 connected directly to Verizon FiOS Circuit (ONT) box using Ethernet cable. As per the existing documention that I have, the previous configured this as a dedicated router to establish a seperate VPN connection our software provider. They assigned both Public Static and Local Static IP address. When I try to ping the public IP address, it says request time out; so the public IP address is no longer working.
When I ping the local IP address of 192.168.100.11, it responds. The SolarWind tool also shows Always UP signal. How can I login into this router either from remotely or locally to check the configuration, backup and do the fimrware upgrade?
I also tried to connect my laptop directly to the ASA 5505 router LAN port. After 3 minutes, I'm able to connect to Internet without any issues. However I don't know the IP address to use to login.
Any advice would be greatly appreciated. Thank you.
UPDATE: I'm able to find the way! I need to use https to login! I'm able to download ASDM tool and login! Thanks to these resources:
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008067e9f9.shtml
http://cyruslab.wordpress.com/2010/09/09/how-to-download-asdm-from-asa5505-and-install-it/Hi Srinath,
If that ASA5505 has factory-default configuration on it , then it probably has 192.168.1.1 ip address on the LAN side and has got dhcp server turned on to provide you ip address dynamically the moment you hook up a machine to it directly or through a switch.
If you've access to ASDM.
You can go the Configuration Tab>>Device Management>>Device Access and turn on the SSH & Telnet from the LAN interface because by default only HTTPS/ASDM is enabled on LAN interface.
You will still need to generate crypto keys and create a username in order to get ssh working
For this you can click at the TOP at TOOLS>> Command Line Interface.
And in the box below type this
crypto key generate rsa modulus 1024
add a username
username <> password <> priv 15
and enable aaa authentication for ssh like this
aaa authentication ssh console LOCAL
Let me know if this helps.
Puneet -
ASA 5505, how to configure DMZ to Inside traffic flows
Dear.
We have a Cisco ASA 5505 with an outside, inside and DMZ interface.
We really need all these interfaces.
The DMZ interface has been configured to block any traffic to the inside (restrict traffic flow). This restriction can’t be disable, an error occurred when doing this.
I will allow only one single port has access from DMZ to the inside, is that possible? And how?
Thanks for the feedback.
Regards.
Peter.What i mean with "can't be disabled": when you navigate to Configuration/interfaces and select the DMZ interface / advanced, you can block traffic. By default Inside has been selected in the drop-down box. However, you can't leave it blank, you need to specify at least one. I can't create another, extra interfaces because the license is 3 max.
So, my question is: can I create a rule somewhere to overwrite this setting for only one specific port? And how?
Result of the command: "show version"
Cisco Adaptive Security Appliance Software Version 8.2(5)
Device Manager Version 6.4(5)
Compiled on Fri 20-May-11 16:00 by builders
System image file is "disk0:/asa825-k8.bin"
Config file at boot was "startup-config"
router up 100 days 1 hour
Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.05
0: Int: Internal-Data0/0 : address is a44c.11bb.5492, irq 11
1: Ext: Ethernet0/0 : address is a44c.11bb.548a, irq 255
2: Ext: Ethernet0/1 : address is a44c.11bb.548b, irq 255
3: Ext: Ethernet0/2 : address is a44c.11bb.548c, irq 255
4: Ext: Ethernet0/3 : address is a44c.11bb.548d, irq 255
5: Ext: Ethernet0/4 : address is a44c.11bb.548e, irq 255
6: Ext: Ethernet0/5 : address is a44c.11bb.548f, irq 255
7: Ext: Ethernet0/6 : address is a44c.11bb.5490, irq 255
8: Ext: Ethernet0/7 : address is a44c.11bb.5491, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not used : irq 255
11: Int: Not used : irq 255
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : 50
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
SSL VPN Peers : 2
Total VPN Peers : 10
Dual ISPs : Disabled
VLAN Trunk Ports : 0
Shared License : Disabled
AnyConnect for Mobile : Disabled
AnyConnect for Cisco VPN Phone : Disabled
AnyConnect Essentials : Disabled
Advanced Endpoint Assessment : Disabled
UC Phone Proxy Sessions : 2
Total UC Proxy Sessions : 2
Botnet Traffic Filter : Disabled
This platform has a Base license.
Serial Number: xxxxxxxxxxxxxx
Running Activation Key: xxxxxxxxxxxxxxxxxxxxxxxxxxxx
Configuration register is 0x1
Configuration last modified by enable_15 at 14:43:11.295 CEDT Mon Sep 9 2013 -
Asa 5505 Ipsec/ipad configuration
Hey Got some issues when setting up IPSEC/VPN on the asa 5505. I want to connect from the ipad with the built in IPSec client..
Get these errors when i run the debug crypto isakmp
Jan 28 22:03:26 [IKEv1]: Group = VPN_ipad, Username = Haq, IP = x.x.x.x, Tunnel Rejected: Conflicting protocols specified by tunnel-group and group-policy
Jan 28 22:03:26 [IKEv1]: Group = VPN_ipad, Username = Haq, IP = x.x.x.x, QM FSM error (P2 struct &0xd5d5f3d8, mess id 0x295bc3a)!
Jan 28 22:03:26 [IKEv1]: Group = VPN_ipad, Username = Haq, IP = x.x.x.x, Removing peer from correlator table failed, no match!
There is a bunch of vpn site-to-site and ipsec vpn profiles setup and those works fine..?
Here is the running config sh run crypto:
crypto ipsec transform-set DES esp-des esp-md5-hmac
crypto ipsec transform-set 3DES-TRANS esp-3des esp-sha-hmac
crypto ipsec transform-set 3DES-TRANS mode transport
crypto ipsec transform-set AES esp-aes esp-sha-hmac
crypto ipsec transform-set 3des esp-3des esp-md5-hmac
crypto ipsec transform-set IPAD-IPSEC esp-3des esp-sha-hmac
crypto ipsec transform-set IPAD-IPSEC mode transport
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map Plandent 10 set transform-set ESP-AES-128-SHA ESP-AES-256-SHA ESP-AES-128-MD5 ESP-AES-256-MD5 DES 3des 3DES-TRANS
crypto dynamic-map Plandent 10 set security-association lifetime seconds 84600
crypto dynamic-map Plandent 10 set security-association lifetime kilobytes 300000
crypto dynamic-map IPAD-MAP 5 set transform-set IPAD-IPSEC
crypto dynamic-map IPAD-MAP 5 set security-association lifetime seconds 28800
crypto dynamic-map IPAD-MAP 5 set security-association lifetime kilobytes 4608000
crypto map PD_VPN 10 match address ToGoteborg
crypto map PD_VPN 10 set peer PixGoteborg
crypto map PD_VPN 10 set transform-set DES
crypto map PD_VPN 10 set security-association lifetime seconds 84600
crypto map PD_VPN 10 set security-association lifetime kilobytes 4608000
crypto map PD_VPN 20 match address ToMalmo
crypto map PD_VPN 20 set peer PixMalmo
crypto map PD_VPN 20 set transform-set DES
crypto map PD_VPN 20 set security-association lifetime seconds 84600
crypto map PD_VPN 20 set security-association lifetime kilobytes 4608000
crypto map PD_VPN 30 match address ToPlanmeca
crypto map PD_VPN 30 set peer ASA_HKI ASA_HKI_BACKUP
crypto map PD_VPN 30 set transform-set AES
crypto map PD_VPN 30 set security-association lifetime seconds 86400
crypto map PD_VPN 30 set security-association lifetime kilobytes 4608000
crypto map PD_VPN 100 ipsec-isakmp dynamic Plandent
crypto map PD_VPN interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 10
authentication pre-share
encryption aes
hash sha
group 2
lifetime 28800
crypto isakmp policy 30
authentication pre-share
encryption des
hash md5
group 2
lifetime 86400
Anyone have any tips and tricks on what can be wrong here, will really be appreciated
Thanks
ShaneWell i created a new tunnel-group and a new group policy its still give me this error? that the tunnel is rejected:
Conflicting protocols specified by tunnel-group and group-policy
But as you can see the ipsec is allowed?
tunnel-group PLANDENT_IPAD type remote-access
tunnel-group PLANDENT_IPAD general-attributes
address-pool IPAD_VPN
default-group-policy PLANDENT_IPAD_Policy
tunnel-group PLANDENT_IPAD ipsec-attributes
pre-shared-key *
group-policy PLANDENT_IPAD_Policy internal
group-policy PLANDENT_IPAD_Policy attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPN_ipad_splitTunnelAcl
/Shane -
Fairly new to cisco ASA 5505 - Can someone look through my config?
Hi.
Can some one tell me if I did the NAT part right? Both dynamic and static.
To be able to reach one vlan from another I created a Nat between them, is this the right way to do it?
I can still limit the access between the vlans based on the access list.
I also getting slow throughput over the VPN tunnel. Is there something wrong with my config. I used the wizard to set it up. There is also a cisco asa5505 on the other end.
If there is some thing else that seems wrong, please let me know.
Any help would be greatfully appreciated!
Config:
: Saved
ASA Version 7.2(2)
hostname ciscoasa
domain-name default.domain.invalid
enable password x encrypted
names
name 192.168.1.250 DomeneServer
name 192.168.1.10 NotesServer
name 192.168.1.90 OvServer
name 192.168.1.97 TerminalServer
name 192.168.1.98 w8-eyeshare
name 192.168.50.10 w8-print
name 192.168.1.94 w8-app
name 192.168.1.89 FonnaFlyMedia
interface Vlan1
nameif Vlan1
security-level 100
ip address 192.168.200.100 255.255.255.0
ospf cost 10
interface Vlan2
nameif outside
security-level 0
ip address 79.x.x.226 255.255.255.224
ospf cost 10
interface Vlan400
nameif vlan400
security-level 100
ip address 192.168.1.1 255.255.255.0
ospf cost 10
interface Vlan450
nameif Vlan450
security-level 100
ip address 192.168.210.1 255.255.255.0
ospf cost 10
interface Vlan460
nameif Vlan460-SuldalHotell
security-level 100
ip address 192.168.2.1 255.255.255.0
ospf cost 10
interface Vlan461
nameif Vlan461-SuldalHotellGjest
security-level 100
ip address 192.168.3.1 255.255.255.0
ospf cost 10
interface Vlan462
nameif Vlan462-Suldalsposten
security-level 100
ip address 192.168.4.1 255.255.255.0
ospf cost 10
interface Vlan470
nameif vlan470-Kyrkjekontoret
security-level 100
ip address 192.168.202.1 255.255.255.0
ospf cost 10
interface Vlan480
nameif vlan480-Telefoni
security-level 100
ip address 192.168.20.1 255.255.255.0
ospf cost 10
interface Vlan490
nameif Vlan490-QNapBackup
security-level 100
ip address 192.168.10.1 255.255.255.0
ospf cost 10
interface Vlan500
nameif Vlan500-HellandBadlands
security-level 100
ip address 192.168.30.1 255.255.255.0
ospf cost 10
interface Vlan510
nameif Vlan510-IsTak
security-level 100
ip address 192.168.40.1 255.255.255.0
ospf cost 10
interface Vlan600
nameif Vlan600-SafeQ
security-level 100
ip address 192.168.50.1 255.255.255.0
ospf cost 10
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
switchport access vlan 500
switchport trunk allowed vlan 400,450,460-462,470,480,500,510,600,610
switchport mode trunk
interface Ethernet0/3
switchport access vlan 490
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
passwd x encrypted
ftp mode passive
clock timezone WAT 1
dns server-group DefaultDNS
domain-name default.domain.invalid
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group service Lotus_Notes_Utgaaande tcp
description Frim Notes og ut til alle
port-object eq domain
port-object eq ftp
port-object eq www
port-object eq https
port-object eq lotusnotes
port-object eq pop3
port-object eq pptp
port-object eq smtp
object-group service Lotus_Notes_inn tcp
description From alle og inn til Notes
port-object eq www
port-object eq lotusnotes
port-object eq pop3
port-object eq smtp
object-group service Reisebyraa tcp-udp
port-object range 3702 3702
port-object range 5500 5500
port-object range 9876 9876
object-group service Remote_Desktop tcp-udp
description Tilgang til Remote Desktop
port-object range 3389 3389
object-group service Sand_Servicenter_50000 tcp-udp
description Program tilgang til Sand Servicenter AS
port-object range 50000 50000
object-group service VNC_Remote_Admin tcp
description Frå oss til alle
port-object range 5900 5900
object-group service Printer_Accept tcp-udp
port-object range 9100 9100
port-object eq echo
object-group icmp-type Echo_Ping
icmp-object echo
icmp-object echo-reply
object-group service Print tcp
port-object range 9100 9100
object-group service FTP_NADA tcp
description Suldalsposten NADA tilgang
port-object eq ftp
port-object eq ftp-data
object-group service Telefonsentral tcp
description Hoftun
port-object eq ftp
port-object eq ftp-data
port-object eq www
port-object eq https
port-object eq telnet
object-group service Printer_inn_800 tcp
description Fra 800 nettet og inn til 400 port 7777
port-object range 7777 7777
object-group service Suldalsposten tcp
description Sending av mail vha Mac Mail programmet - åpner smtp
port-object eq pop3
port-object eq smtp
object-group service http2 tcp
port-object range 81 81
object-group service DMZ_FTP_PASSIVE tcp-udp
port-object range 55536 56559
object-group service DMZ_FTP tcp-udp
port-object range 20 21
object-group service DMZ_HTTPS tcp-udp
port-object range 443 443
object-group service DMZ_HTTP tcp-udp
port-object range 8080 8080
object-group service DNS_Query tcp
port-object range domain domain
object-group service DUETT_SQL_PORT tcp-udp
description For kobling mellom andre nett og duett server
port-object range 54659 54659
access-list outside_access_in extended permit ip any any
access-list outside_access_out extended permit ip any any
access-list vlan400_access_in extended deny ip any host 149.20.56.34
access-list vlan400_access_in extended deny ip any host 149.20.56.32
access-list vlan400_access_in extended permit ip any any
access-list Vlan450_access_in extended deny ip any host 149.20.56.34
access-list Vlan450_access_in extended deny ip any host 149.20.56.32
access-list Vlan450_access_in extended permit ip any any
access-list Vlan460_access_in extended deny ip any host 149.20.56.34
access-list Vlan460_access_in extended deny ip any host 149.20.56.32
access-list Vlan460_access_in extended permit ip any any
access-list vlan400_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan400_access_out extended permit tcp any host NotesServer object-group Lotus_Notes_Utgaaande
access-list vlan400_access_out extended permit tcp any host DomeneServer object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host TerminalServer object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host OvServer object-group http2
access-list vlan400_access_out extended permit tcp any host NotesServer object-group Lotus_Notes_inn
access-list vlan400_access_out extended permit tcp any host NotesServer object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host w8-eyeshare object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host w8-app object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host FonnaFlyMedia range 8400 8600
access-list vlan400_access_out extended permit udp any host FonnaFlyMedia range 9000 9001
access-list vlan400_access_out extended permit tcp 192.168.4.0 255.255.255.0 host DomeneServer
access-list vlan400_access_out extended permit tcp 192.168.4.0 255.255.255.0 host w8-app object-group DUETT_SQL_PORT
access-list Vlan500_access_in extended deny ip any host 149.20.56.34
access-list Vlan500_access_in extended deny ip any host 149.20.56.32
access-list Vlan500_access_in extended permit ip any any
access-list vlan470_access_in extended deny ip any host 149.20.56.34
access-list vlan470_access_in extended deny ip any host 149.20.56.32
access-list vlan470_access_in extended permit ip any any
access-list Vlan490_access_in extended deny ip any host 149.20.56.34
access-list Vlan490_access_in extended deny ip any host 149.20.56.32
access-list Vlan490_access_in extended permit ip any any
access-list Vlan450_access_out extended permit icmp any any object-group Echo_Ping
access-list Vlan1_access_out extended permit ip any any
access-list Vlan1_access_out extended permit tcp any host w8-print object-group Remote_Desktop
access-list Vlan1_access_out extended deny ip any any
access-list Vlan1_access_out extended permit icmp any any echo-reply
access-list Vlan460_access_out extended permit icmp any any object-group Echo_Ping
access-list Vlan490_access_out extended permit icmp any any object-group Echo_Ping
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_FTP
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_FTP_PASSIVE
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_HTTPS
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_HTTP
access-list Vlan500_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan470_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan470_access_out extended permit tcp any host 192.168.202.10 object-group Remote_Desktop
access-list Vlan510_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan480_access_out extended permit ip any any
access-list Vlan510_access_in extended permit ip any any
access-list Vlan600_access_in extended permit ip any any
access-list Vlan600_access_out extended permit icmp any any
access-list Vlan600_access_out extended permit tcp any host w8-print object-group Remote_Desktop
access-list Vlan600_access_out extended permit tcp 192.168.1.0 255.255.255.0 host w8-print eq www
access-list Vlan600_access_out extended permit tcp 192.168.202.0 255.255.255.0 host w8-print eq www
access-list Vlan600_access_out extended permit tcp 192.168.210.0 255.255.255.0 host w8-print eq www
access-list Vlan600_access_in_1 extended permit ip any any
access-list Vlan461_access_in extended permit ip any any
access-list Vlan461_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan400_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list outside_20_cryptomap_1 extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list outside_20_cryptomap extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list Vlan462-Suldalsposten_access_in extended permit ip any any
access-list Vlan462-Suldalsposten_access_out extended permit icmp any any echo-reply
access-list Vlan462-Suldalsposten_access_out_1 extended permit icmp any any echo-reply
access-list Vlan462-Suldalsposten_access_in_1 extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu Vlan1 1500
mtu outside 1500
mtu vlan400 1500
mtu Vlan450 1500
mtu Vlan460-SuldalHotell 1500
mtu Vlan461-SuldalHotellGjest 1500
mtu vlan470-Kyrkjekontoret 1500
mtu vlan480-Telefoni 1500
mtu Vlan490-QNapBackup 1500
mtu Vlan500-HellandBadlands 1500
mtu Vlan510-IsTak 1500
mtu Vlan600-SafeQ 1500
mtu Vlan462-Suldalsposten 1500
no failover
monitor-interface Vlan1
monitor-interface outside
monitor-interface vlan400
monitor-interface Vlan450
monitor-interface Vlan460-SuldalHotell
monitor-interface Vlan461-SuldalHotellGjest
monitor-interface vlan470-Kyrkjekontoret
monitor-interface vlan480-Telefoni
monitor-interface Vlan490-QNapBackup
monitor-interface Vlan500-HellandBadlands
monitor-interface Vlan510-IsTak
monitor-interface Vlan600-SafeQ
monitor-interface Vlan462-Suldalsposten
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-522.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (vlan400) 0 access-list vlan400_nat0_outbound
nat (vlan400) 1 0.0.0.0 0.0.0.0 dns
nat (Vlan450) 1 0.0.0.0 0.0.0.0 dns
nat (Vlan460-SuldalHotell) 1 0.0.0.0 0.0.0.0
nat (Vlan461-SuldalHotellGjest) 1 0.0.0.0 0.0.0.0
nat (vlan470-Kyrkjekontoret) 1 0.0.0.0 0.0.0.0
nat (Vlan490-QNapBackup) 1 0.0.0.0 0.0.0.0 dns
nat (Vlan500-HellandBadlands) 1 0.0.0.0 0.0.0.0
nat (Vlan510-IsTak) 1 0.0.0.0 0.0.0.0
nat (Vlan600-SafeQ) 1 0.0.0.0 0.0.0.0
nat (Vlan462-Suldalsposten) 1 0.0.0.0 0.0.0.0
static (vlan400,outside) 79.x.x.x DomeneServer netmask 255.255.255.255
static (vlan470-Kyrkjekontoret,outside) 79.x.x.x 192.168.202.10 netmask 255.255.255.255
static (vlan400,outside) 79.x.x.x NotesServer netmask 255.255.255.255 dns
static (vlan400,outside) 79.x.x.231 TerminalServer netmask 255.255.255.255
static (vlan400,outside) 79.x.x.234 OvServer netmask 255.255.255.255
static (vlan400,outside) 79.x.x.232 w8-eyeshare netmask 255.255.255.255
static (Vlan490-QNapBackup,outside) 79.x.x.233 192.168.10.10 netmask 255.255.255.255 dns
static (Vlan600-SafeQ,outside) 79.x.x.235 w8-print netmask 255.255.255.255
static (vlan400,outside) 79.x.x.236 w8-app netmask 255.255.255.255
static (Vlan450,vlan400) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
static (Vlan500-HellandBadlands,vlan400) 192.168.30.0 192.168.30.0 netmask 255.255.255.0
static (vlan400,Vlan500-HellandBadlands) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400,Vlan450) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400,outside) 79.x.x.252 FonnaFlyMedia netmask 255.255.255.255
static (Vlan462-Suldalsposten,vlan400) 192.168.4.0 192.168.4.0 netmask 255.255.255.0
static (vlan400,Vlan462-Suldalsposten) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400,Vlan600-SafeQ) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (Vlan600-SafeQ,vlan400) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ,Vlan450) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ,vlan470-Kyrkjekontoret) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan450,Vlan600-SafeQ) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
static (vlan470-Kyrkjekontoret,Vlan600-SafeQ) 192.168.202.0 192.168.202.0 netmask 255.255.255.0
access-group Vlan1_access_out out interface Vlan1
access-group outside_access_in in interface outside
access-group outside_access_out out interface outside
access-group vlan400_access_in in interface vlan400
access-group vlan400_access_out out interface vlan400
access-group Vlan450_access_in in interface Vlan450
access-group Vlan450_access_out out interface Vlan450
access-group Vlan460_access_in in interface Vlan460-SuldalHotell
access-group Vlan460_access_out out interface Vlan460-SuldalHotell
access-group Vlan461_access_in in interface Vlan461-SuldalHotellGjest
access-group Vlan461_access_out out interface Vlan461-SuldalHotellGjest
access-group vlan470_access_in in interface vlan470-Kyrkjekontoret
access-group vlan470_access_out out interface vlan470-Kyrkjekontoret
access-group vlan480_access_out out interface vlan480-Telefoni
access-group Vlan490_access_in in interface Vlan490-QNapBackup
access-group Vlan490_access_out out interface Vlan490-QNapBackup
access-group Vlan500_access_in in interface Vlan500-HellandBadlands
access-group Vlan500_access_out out interface Vlan500-HellandBadlands
access-group Vlan510_access_in in interface Vlan510-IsTak
access-group Vlan510_access_out out interface Vlan510-IsTak
access-group Vlan600_access_in_1 in interface Vlan600-SafeQ
access-group Vlan600_access_out out interface Vlan600-SafeQ
access-group Vlan462-Suldalsposten_access_in_1 in interface Vlan462-Suldalsposten
access-group Vlan462-Suldalsposten_access_out_1 out interface Vlan462-Suldalsposten
route outside 0.0.0.0 0.0.0.0 79.x.x.225 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
username x password x encrypted privilege 15
aaa authentication ssh console LOCAL
http server enable
http 192.168.210.0 255.255.255.0 Vlan450
http 192.168.200.0 255.255.255.0 Vlan1
http 192.168.1.0 255.255.255.0 vlan400
no snmp-server location
no snmp-server contact
snmp-server community public
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto map outside_map 20 match address outside_20_cryptomap_1
crypto map outside_map 20 set pfs
crypto map outside_map 20 set peer 62.92.159.137
crypto map outside_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp enable vlan400
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
tunnel-group 62.92.159.137 type ipsec-l2l
tunnel-group 62.92.159.137 ipsec-attributes
pre-shared-key *
telnet 192.168.200.0 255.255.255.0 Vlan1
telnet 192.168.1.0 255.255.255.0 vlan400
telnet timeout 5
ssh 171.68.225.216 255.255.255.255 outside
ssh timeout 5
console timeout 0
dhcpd update dns both
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan1
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface outside
dhcpd address 192.168.1.100-192.168.1.225 vlan400
dhcpd option 6 ip DomeneServer 81.167.36.11 interface vlan400
dhcpd option 3 ip 192.168.1.1 interface vlan400
dhcpd enable vlan400
dhcpd address 192.168.210.100-192.168.210.200 Vlan450
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan450
dhcpd option 3 ip 192.168.210.1 interface Vlan450
dhcpd enable Vlan450
dhcpd address 192.168.2.100-192.168.2.150 Vlan460-SuldalHotell
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan460-SuldalHotell
dhcpd option 3 ip 192.168.2.1 interface Vlan460-SuldalHotell
dhcpd enable Vlan460-SuldalHotell
dhcpd address 192.168.3.100-192.168.3.200 Vlan461-SuldalHotellGjest
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan461-SuldalHotellGjest
dhcpd option 3 ip 192.168.3.1 interface Vlan461-SuldalHotellGjest
dhcpd enable Vlan461-SuldalHotellGjest
dhcpd address 192.168.202.100-192.168.202.199 vlan470-Kyrkjekontoret
dhcpd option 3 ip 192.168.202.1 interface vlan470-Kyrkjekontoret
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan470-Kyrkjekontoret
dhcpd enable vlan470-Kyrkjekontoret
dhcpd option 3 ip 192.168.20.1 interface vlan480-Telefoni
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan480-Telefoni
dhcpd address 192.168.10.80-192.168.10.90 Vlan490-QNapBackup
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan490-QNapBackup
dhcpd option 3 ip 192.168.10.1 interface Vlan490-QNapBackup
dhcpd address 192.168.30.100-192.168.30.199 Vlan500-HellandBadlands
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan500-HellandBadlands
dhcpd option 3 ip 192.168.30.1 interface Vlan500-HellandBadlands
dhcpd enable Vlan500-HellandBadlands
dhcpd address 192.168.40.100-192.168.40.150 Vlan510-IsTak
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan510-IsTak
dhcpd option 3 ip 192.168.40.1 interface Vlan510-IsTak
dhcpd enable Vlan510-IsTak
dhcpd address 192.168.50.150-192.168.50.199 Vlan600-SafeQ
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan600-SafeQ
dhcpd enable Vlan600-SafeQ
dhcpd address 192.168.4.100-192.168.4.150 Vlan462-Suldalsposten
dhcpd option 6 ip DomeneServer 81.167.36.11 interface Vlan462-Suldalsposten
dhcpd option 3 ip 192.168.4.1 interface Vlan462-Suldalsposten
dhcpd enable Vlan462-Suldalsposten
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
prompt hostname context
Cryptochecksum:x
: endI was just wondering if this is the way to do the "connection" between vlans.. or should it be routed?
The traffic between the vlan is working as intended. There are not much traffice only some RDP connection and some printing jobs.
But i'm getting some of these errors: (not alle like this, but portmap translation creation failed)
305006 192.168.10.200 portmap translation creation failed for udp src Vlan460-SuldalHotell:192.168.2.112/59133 dst Vlan490-QNapBackup:192.168.10.200/161
I did the sh interface commends:
Result of the command: "sh interface"
Interface Vlan1 "Vlan1", is down, line protocol is down
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.200.100, subnet mask 255.255.255.0
Traffic Statistics for "Vlan1":
0 packets input, 0 bytes
0 packets output, 0 bytes
0 packets dropped
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan2 "outside", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 79.x.x.226, subnet mask 255.255.255.224
Traffic Statistics for "outside":
1780706730 packets input, 1221625431570 bytes
1878320718 packets output, 1743030863134 bytes
5742216 packets dropped
1 minute input rate 558 pkts/sec, 217568 bytes/sec
1 minute output rate 803 pkts/sec, 879715 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 621 pkts/sec, 482284 bytes/sec
5 minute output rate 599 pkts/sec, 428957 bytes/sec
5 minute drop rate, 1 pkts/sec
Interface Vlan400 "vlan400", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.1.1, subnet mask 255.255.255.0
Traffic Statistics for "vlan400":
1093422654 packets input, 1191121436317 bytes
784209789 packets output, 374041914789 bytes
11465163 packets dropped
1 minute input rate 751 pkts/sec, 870445 bytes/sec
1 minute output rate 462 pkts/sec, 116541 bytes/sec
1 minute drop rate, 11 pkts/sec
5 minute input rate 474 pkts/sec, 415304 bytes/sec
5 minute output rate 379 pkts/sec, 197861 bytes/sec
5 minute drop rate, 7 pkts/sec
Interface Vlan450 "Vlan450", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.210.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan450":
139711812 packets input, 27519985266 bytes
202793062 packets output, 233679075458 bytes
12523100 packets dropped
1 minute input rate 68 pkts/sec, 9050 bytes/sec
1 minute output rate 83 pkts/sec, 88025 bytes/sec
1 minute drop rate, 6 pkts/sec
5 minute input rate 145 pkts/sec, 15068 bytes/sec
5 minute output rate 241 pkts/sec, 287093 bytes/sec
5 minute drop rate, 6 pkts/sec
Interface Vlan460 "Vlan460-SuldalHotell", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.2.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan460-SuldalHotell":
177971988 packets input, 161663208458 bytes
193137004 packets output, 137418896469 bytes
4003957 packets dropped
1 minute input rate 13 pkts/sec, 2295 bytes/sec
1 minute output rate 14 pkts/sec, 15317 bytes/sec
1 minute drop rate, 2 pkts/sec
5 minute input rate 4 pkts/sec, 794 bytes/sec
5 minute output rate 1 pkts/sec, 477 bytes/sec
5 minute drop rate, 2 pkts/sec
Interface Vlan461 "Vlan461-SuldalHotellGjest", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.3.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan461-SuldalHotellGjest":
332909692 packets input, 351853184942 bytes
312038518 packets output, 156669956740 bytes
583171 packets dropped
1 minute input rate 0 pkts/sec, 6 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 6 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan462 "Vlan462-Suldalsposten", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.4.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan462-Suldalsposten":
33905 packets input, 14303320 bytes
28285 packets output, 27536357 bytes
10199 packets dropped
1 minute input rate 0 pkts/sec, 6 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 6 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan470 "vlan470-Kyrkjekontoret", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.202.1, subnet mask 255.255.255.0
Traffic Statistics for "vlan470-Kyrkjekontoret":
12176257 packets input, 4305665570 bytes
10618750 packets output, 5982598969 bytes
974796 packets dropped
1 minute input rate 2 pkts/sec, 770 bytes/sec
1 minute output rate 1 pkts/sec, 861 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 2 pkts/sec, 708 bytes/sec
5 minute output rate 1 pkts/sec, 980 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan480 "vlan480-Telefoni", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.20.1, subnet mask 255.255.255.0
Traffic Statistics for "vlan480-Telefoni":
246638 packets input, 43543149 bytes
10 packets output, 536 bytes
226674 packets dropped
1 minute input rate 0 pkts/sec, 126 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 56 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan490 "Vlan490-QNapBackup", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.10.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan490-QNapBackup":
137317833 packets input, 6066713912 bytes
223933623 packets output, 263191563744 bytes
531738 packets dropped
1 minute input rate 0 pkts/sec, 135 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 68 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan500 "Vlan500-HellandBadlands", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.30.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan500-HellandBadlands":
30816778 packets input, 4887486069 bytes
42403099 packets output, 47831750415 bytes
948717 packets dropped
1 minute input rate 3 pkts/sec, 707 bytes/sec
1 minute output rate 3 pkts/sec, 3459 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 23 bytes/sec
5 minute output rate 0 pkts/sec, 31 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan510 "Vlan510-IsTak", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.40.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan510-IsTak":
1253148 packets input, 245364736 bytes
1225385 packets output, 525528101 bytes
161567 packets dropped
1 minute input rate 0 pkts/sec, 6 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 6 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan600 "Vlan600-SafeQ", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.50.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan600-SafeQ":
1875377 packets input, 1267279709 bytes
1056139 packets output, 290728055 bytes
521943 packets dropped
1 minute input rate 0 pkts/sec, 165 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 178 bytes/sec
5 minute output rate 0 pkts/sec, 9 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Ethernet0/0 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
Available but not configured via nameif
MAC address 001d.453a.ea06, MTU not set
IP address unassigned
1782670655 packets input, 1256666911856 bytes, 0 no buffer
Received 95709 broadcasts, 0 runts, 0 giants
1978 input errors, 1978 CRC, 0 frame, 0 overrun, 1978 ignored, 0 abort
0 L2 decode drops
17179928790 switch ingress policy drops
1878320261 packets output, 1778955488577 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Interface Ethernet0/2 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
Available but not configured via nameif
MAC address 001d.453a.ea08, MTU not set
IP address unassigned
1790819459 packets input, 1783854920873 bytes, 0 no buffer
Received 27571913 broadcasts, 0 runts, 0 giants
614 input errors, 614 CRC, 0 frame, 0 overrun, 614 ignored, 0 abort
0 L2 decode drops
19768 switch ingress policy drops
1547507675 packets output, 991527977853 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Interface Ethernet0/3 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
Available but not configured via nameif
MAC address 001d.453a.ea09, MTU not set
IP address unassigned
137318166 packets input, 9176625008 bytes, 0 no buffer
Received 290030 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
335 switch ingress policy drops
223933623 packets output, 267222625073 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops -
Cisco ASA 5505 VPN help for local lan access.
Hi all,
I am very new to Cisco systems. Recently I was tasked to enable local lan access for one of my server. The problem is this. I have this server with 2 interfaces. One interface to my FTP server(192.168.2.3) and the other to the Cisco ASA(192.168.1.1). Whenever I connect the server to Cisco Anyconnect VPN, I am unable to access the FTP server anymore.
I googled and found out that the problem is because the metric level is 1 for Ciscoanyconnect network interface which causes all traffic to go through the Cisco VPN Interface. Another problem is I can't change the metric of the Cisco VPN Interface as whenever I reconnect to the VPN, the metric resets back to 1 again. I tried to follow some guides to configure split tunnel but my traffic is still going through the VPN connection.
Anyone can tell me what I am missing here? Sorry I am very new to Cisco systems. Spent about 5 days troubleshooting and I feel I am getting it soon. Anyone can guide me what else I am supposed to do?
What I did> Configuration>> Remote access VPN>> Network Client Access>> Group Policies>> Advanced>> Split Tunneling>> Uncheck Inherit and select "Exclude Network List below.>> Uncheck Network List and select Manage, Add 192.168.2.0/24 to permit.
Really appreciate if anyone can tell me what else I can do to ensure my server has access the my FTP Server after connecting to the VPN.
Thanks all!
Wen QiHi,
Try adding the following configuration
policy-map global_policy
class inspection_default
inspect pptp
And then try again.
I'm not 100% would you need to perhaps allow GRE through the firewall even after that. (Protocol 47)
- Jouni -
ASA 5505 8.2 - SSL VPN - Cannot Ping inside host's
Hello All,
I'm an ASA Newb.
I feel like I have tried everything posted and still no success.
PROBLEM: When connected to the SSL VPN I cannot ping any internal host's. I cannot ping anything on this inside?
Result of the command: "show running-config"
: Saved
ASA Version 8.2(5)
hostname MCASA01
domain-name mydomain.org
enable password xxbtzv6P4Hqevn4N encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 192.168.2.0 VLAN
name 192.168.5.0 VPNPOOL
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
switchport access vlan 3
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ddns update hostname MC_DNS
dhcp client update dns server both
ip address 192.168.1.1 255.255.255.0
interface Vlan2
no forward interface Vlan1
nameif outside
security-level 0
ip address 11.11.11.202 255.255.255.252
interface Vlan3
no nameif
security-level 50
ip address 192.168.2.1 255.255.255.0
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
dns server-group DefaultDNS
domain-name mydomain.org
access-list SPLIT-TUNNEL standard permit 192.168.1.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPNPOOL 192.168.5.1-192.168.5.10 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 74.7.217.201 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 outside
http authentication-certificate inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto ca trustpoint ASDM_TrustPoint0
enrollment terminal
subject-name CN=vpn.mydomain.org,OU=IT,O="mydomain",C=US,St=CA,L=Chino
keypair digicert.key
crl configure
crypto ca certificate chain ASDM_TrustPoint0
certificate 00b63edadf5efa057ea49da56b179132e8
3082051c 30820404 a0030201 02021100 b63edadf 5efa057e a49da56b 179132e8
300d0609 2a864886 f70d0101 05050030 72310b30 09060355 04061302 4742311b
30190603 55040813 12477265 61746572 204d616e 63686573 74657231 10300e06
03550407 13075361 6c666f72 64311a30 18060355 040a1311 434f4d4f 444f2043
41204c69 6d697465 64311830 16060355 0403130f 45737365 6e746961 6c53534c
20434130 1e170d31 33313130 35303030 3030305a 170d3134 30323033 32333539
35395a30 52312130 1f060355 040b1318 446f6d61 696e2043 6f6e7472 6f6c2056
616c6964 61746564 3111300f 06035504 0b130846 72656520 53534c31 1a301806
03550403 13117670 6e2e6d65 74726f63 656c6c2e 6f726730 82012230 0d06092a
864886f7 0d010101 05000382 010f0030 82010a02 82010100 a0d97d51 fcd18293
eaf8e9b2 d632b2e3 e4d92eb1 5b639766 52677a26 2aa7d09d 437be3b6 dfb8649c
4d715278 e1745955 27e8aab2 9c9da997 694a73e8 c1c426f3 a519adba acc2ad94
aa0e09af 6db7bfc6 bad90bf2 b057dc56 c69a4276 1b826c83 6cd7ae09 af39bd7d
4abe60b4 9b04613a 287a1ae6 9d117d05 c7cdc15f 09d588b0 fcc05c47 c1cb6d67
c3701389 d3b7691d b05ff82c b0be475d 746a4916 0bbf11a6 7ee1b7ec bd05e1d2
dda305a6 918bfd35 17447b04 bca1e6d9 10955649 d8211878 168c4c21 279a6584
4b560a9f 414aea15 91e21581 a71d6b98 86d9eac3 47ea3a1d a172c71a ecf77aaa
536d73e4 bc53eb68 c7bfacdd fab87ea5 121baf55 067dbd19 02030100 01a38201
cb308201 c7301f06 03551d23 04183016 8014dacb eaad5b08 5dccfffc 2654ce49
e555c638 f4f8301d 0603551d 0e041604 14fabb1d f439c41f e59207c7 202c2fda
b46bcacc ee300e06 03551d0f 0101ff04 04030205 a0300c06 03551d13 0101ff04
02300030 34060355 1d25042d 302b0608 2b060105 05070301 06082b06 01050507
0302060a 2b060104 0182370a 03030609 60864801 86f84204 01304f06 03551d20
04483046 303a060b 2b060104 01b23101 02020730 2b302906 082b0601 05050702
01161d68 74747073 3a2f2f73 65637572 652e636f 6d6f646f 2e636f6d 2f435053
30080606 67810c01 0201303b 0603551d 1f043430 323030a0 2ea02c86 2a687474
703a2f2f 63726c2e 636f6d6f 646f6361 2e636f6d 2f457373 656e7469 616c5353
4c43412e 63726c30 6e06082b 06010505 07010104 62306030 3806082b 06010505
07300286 2c687474 703a2f2f 6372742e 636f6d6f 646f6361 2e636f6d 2f457373
656e7469 616c5353 4c43415f 322e6372 74302406 082b0601 05050730 01861868
7474703a 2f2f6f63 73702e63 6f6d6f64 6f63612e 636f6d30 33060355 1d11042c
302a8211 76706e2e 6d657472 6f63656c 6c2e6f72 67821577 77772e76 706e2e6d
6574726f 63656c6c 2e6f7267 300d0609 2a864886 f70d0101 05050003 82010100
2484b72c 56161585 c9caa1a3 43cbc754 d3b43cef 7902a775 d40d064f 6918d52f
0aaaea0c ad873124 11b68847 406812da fd0c5d71 6e110898 1ebddcab ddf980e4
b95be4e2 0633cc23 7a4cbc27 f1f5e4e8 1de3c127 2b28a364 f1f26764 98afe871
45547855 c0ceaf39 256f46db 4ac412a7 2b594817 a967ba5a 24986b24 57002ce4
f046c6b3 5f7c9cc2 e6cd8ede 8fbcac60 b87fd497 71328783 8b148f7f affec249
191c460b 3d46d352 0651f35e 96a60fbe 7b22e057 06aa7722 da447cd3 0ea72e7f
5ec8c13c b550f502 b020efdc 35f62b89 52d7e6e3 14ade632 802dee70 1cdbf7ad
a39a173b 916406e4 887ba623 4813b925 8a63a300 fd016981 a8d70651 a736267a
quit
no crypto isakmp nat-traversal
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 5
console timeout 0
dhcpd auto_config outside vpnclient-wins-override
dhcpd address 192.168.1.100-192.168.1.200 inside
dhcpd dns 66.180.96.12 64.238.96.12 interface inside
dhcpd lease 86400 interface inside
dhcpd ping_timeout 4000 interface inside
dhcpd domain mydomain.org interface inside
threat-detection basic-threat
threat-detection statistics access-list
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
ntp server 64.147.116.229 source outside
ssl trust-point ASDM_TrustPoint0 outside
webvpn
enable outside
svc image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
svc enable
tunnel-group-list enable
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
group-policy VPNGP internal
group-policy VPNGP attributes
vpn-tunnel-protocol svc
split-tunnel-policy tunnelspecified
split-tunnel-network-list value SPLIT-TUNNEL
username GaryC password TGbvzEO3d6HlfU66 encrypted privilege 15
username GaryC attributes
vpn-group-policy VPNGP
tunnel-group MCVPN type remote-access
tunnel-group MCVPN general-attributes
address-pool VPNPOOL
default-group-policy VPNGP
tunnel-group MCVPN webvpn-attributes
group-alias MCVPN enable
group-url https://11.11.11.202/MCVPN enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:1e950c041cc2c25116d30e5c884abbfc
: end
My goal is to allow Remote Users to RDP(3389) through VPN.
Thank you,
Gary
Message was edited by: Gary CulwellHello Jon,
Thank you so much for your response. Clients will not be connect to a specific RDP server. I was hoping if we were to establish a VPN Client tunnel I would like that tunnel to provide full local are access. So the way the clients are used to is while in the field they use RDP to connect to their desktops on the internal LAN.
Would you say this would work:
route inside 192.168.1.0 255.255.255.0 192.168.1.1 1
Do you have examples?
Thank you,
Gary -
Cisco Asa 5505 and Layer 3 Switch With Remote VPN Access
i got today a new CISCO LAYER 3 Switch .. so here is my scenrio
Cisco Asa 5505
I
Outside == 155.155.155.x
Inside = 192.168.7.1
VPN POOL Address = 10.10.10.1 - 10.10.10.20
Layer 3 Switch Config
Vlan 2
interface ip address = 192.168.1.1
Vlan 2
interface ip address = 192.168.2.1
Vlan 2
interface ip address = 192.168.3.1
Vlan 2
interface ip address = 192.168.4.1
Vlan 2
interface ip address = 192.168.5.1
ip Routing
So i want My Remote Access VPN clients to access all this Networks. So Please can you give me a helpfull trick or Link to configure the rest of my routing
Thank You allWhen My Remote VPN is Connected , it reaches 192.168.7.2 of the Layer 3 VLan that's Connected to The ASA 5505 ,
But i can't reach the rest of the VLAN - example
192.168.1.1
192.168.1.2
192.168.1.3
192.168.1.4
192.168.1.5
But i can reach the Connected Interface Vlan to My ASA ..
So here i think iam miss configuration to my Route
Any Help Please this is urgent -
Problems with basic config ASA 5505
new ASA 5505, tying to configure it, inside LAN is 192.168.2.x/23 (255.255.254.0). I connect to ASA5505 using ASDM ok when it is on the default 192.168.1.1. I change the ip on 'inside' vlan, and of course lose connection to it. It apparently doesn't totally save the info, though, because I can't connect to it using the new info. So, I made a vlan3, using port 0/2, using ip of 192.168.2.x/23 while connected to 192.168.1.1. Then I changed ip of my computer from 192.168.1.x to 192.168.2.x/23 but cannot even ping that port/ip on the ASA while connected to port 0/2. I switched computer back, and connected again to 192.168.1.1 and it does appear that my new settings for 0/2 are still there, so I'm not sure how to proceed? Thanks.
Sorry, had family emergency and was off for 2 weeks, then when came back had other work to catch up on.
Thanks for the reply. It would appear that the command you provided sets it back to default settings. I was able to set it back to default settings, but am now unsure as how to proceed to get the "inside" set to 192.168.2.0/23 and still be able to access it.
If I go back in, I can change "inside" to 192.168.2.1/23, but lose connection, so it "sort of" gets saved, in the respect that sometimes I can ping it, sometimes not. But can never connect to it.
Thanks, and sorry again about the delay. -
ASA 5505 unable to connect inside or outside
Hello,
I'm extremely new to router configurations, and am attempting to configure a backup ASA 5505 to use as a temporary access point in the event that our main ASA becomes unavailable. What I have done is loaded the running config from our main ASA onto the backup, and have made changes to necessary routes, IPs, etc. I can connect to it from a remote computer without problem, but I cannot access any of our servers, nor can I access the internet. I have also tried modifying the access list and NAT rules every which way from Sunday, but I still cannot get this thing to allow any information through. I keep getting "failed to locate egress interface for UDP from outside" errors.
We are using Cisco AnyConnect to connect , and mind you, since the config for this backup ASA was taken from our main, it still has the original certificate info and profiles. I was told that this wouldn't matter, but I thought I should mention in case I need to remove any of it from the config.
Here is part of the config file. I took out some information, but tried to keep it understandable. If anyone could point me in the right direction, it would be greatly appreciated!
ciscoasa# show running-config
: Saved
: Serial Number: xxxxxxxxxxx
: Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz
ASA Version 9.2(2)
hostname ciscoasa
domain-name domain
enable password encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd encrypted
names
ip local pool pool1 x.x.9.22-x.x.9.254 mask 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address x.x.8.10 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address x.x.x.237 255.255.255.248
boot system disk0:/asa922-k8.bin
boot config disk0:/startup-config
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group Default
name-server x.x.8.100
domain-name domain
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network pool1
subnet x.x.9.0 255.255.255.0
object network outside-network
host x.x.x.237
object network Remote-Network
subnet x.x.8.0 255.255.255.0
object network local
object network obj-x.x.9.24
host x.x.9.24
object-group network Outside-Network-Group
description Outside Network Group
network-object x.x.x.232 255.255.255.248
object-group network Inside-Network-Group
description Inside Network Group
network-object x.x.8.0 255.255.255.0
access-list inside_access_in extended permit icmp any any
access-list inside_access_in extended permit ip any any
access-list NONAT extended permit ip x.x.8.0 255.255.255.0 x.x.9.0 255.255.255.0
pager lines 24
logging enable
logging buffer-size 30000
logging buffered debugging
logging asdm informational
no logging message 106015
no logging message 313001
no logging message 313008
no logging message 106023
no logging message 710003
no logging message 106100
no logging message 302015
no logging message 302014
no logging message 302013
no logging message 302018
no logging message 302017
no logging message 302016
no logging message 302021
no logging message 302020
flow-export destination inside x.x.8.132 2055
flow-export template timeout-rate 1
flow-export delay flow-create 50
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
asdm image disk0:/asdm-722.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static any any destination static pool1 pool1 no-proxy-arp route-lookup
nat (inside,outside) source static any any destination static Remote-Network Remote-Network no-proxy-arp route-lookup
nat (outside,outside) source dynamic pool1 interface
object network obj_any
nat (inside,outside) dynamic interface
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 x.x.x.232 1
route inside x.x.11.0 255.255.255.0 x.x.11.1 1
If you have any questions, or need any other information, please let me know.
Thanks!Am I posting this in the wrong section? Anyone?
-
Problem with asa 5505 routing,nating
i have the asa 5505 with asdm 6.4(5). my inside lan is 192.168.0.0/24. the outside of asa is connected on lan 10.13.74.0/24 and i need over lan 10.13.74.0/24 connect on lan 10.15.100.0/24. i puted nat rule on asa 5505 and acl rule and users from lan 10.15.100.0/24 can connect on my server, but i can't connect on from inside of asa connecet on lan 10.15.100.0/24 and 10.13.74.0/24. my configuration asa is
Result of the command: "show running-config": Saved:ASA Version 8.4(2) !hostname ciscoasaenable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0 switchport access vlan 2!interface Ethernet0/1 switchport access vlan 3!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1 nameif inside security-level 100 ip address 192.168.0.17 255.255.255.0 !interface Vlan2 nameif outside security-level 0 ip address 10.13.74.33 255.255.255.0 !ftp mode passiveobject network obj_any subnet 0.0.0.0 0.0.0.0object network server host 192.168.0.20object service ParagrafLex service tcp source eq 6190 destination eq 6190 object network sharepoint host 192.168.0.22access-list outside_access_in extended permit ip host 10.13.74.35 any access-list outside_access_in_1 extended permit ip any object server access-list outside_access_in_1 extended permit object ParagrafLex 10.15.100.0 255.255.255.0 object server access-list outside_access_in_1 extended permit object ParagrafLex any object server pager lines 24logging asdm informationalmtu inside 1500mtu outside 1500icmp unreachable rate-limit 1 burst-size 1no asdm history enablearp timeout 14400!object network obj_any nat (inside,outside) dynamic interfaceobject network server nat (any,any) static 10.13.74.34access-group outside_access_in in interface outside control-planeaccess-group outside_access_in_1 in interface outsideroute inside 0.0.0.0 0.0.0.0 10.13.74.1 1timeout xlate 3:00:00timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolutetimeout tcp-proxy-reassembly 0:01:00timeout floating-conn 0:00:00dynamic-access-policy-record DfltAccessPolicyuser-identity default-domain LOCALhttp server enablehttp 192.168.1.0 255.255.255.0 insidehttp 10.13.74.0 255.255.255.0 outsideno snmp-server locationno snmp-server contactsnmp-server enable traps snmp authentication linkup linkdown coldstart warmstarttelnet timeout 5ssh timeout 5console timeout 0dhcpd auto_config outside!threat-detection basic-threatthreat-detection statistics access-listno threat-detection statistics tcp-interceptwebvpn!class-map inspection_default match default-inspection-traffic!!policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options !service-policy global_policy globalprompt hostname context no call-home reporting anonymousCryptochecksum:791a1fa6b6fcccaa3177fed821d1f392: end
what i do that connect on lan 10.15.100.0/24. i cant ping my outside interface, puted rules on acl, i enabled sevice policy rule for icmp ,but nothing. pleas help me
thanksmy configuration asa 5505 is now
Result of the command: "show running-config"
: Saved
ASA Version 8.4(2)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.17 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 10.13.74.33 255.255.255.0
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network server
host 192.168.0.20
object service ParagrafLex
service tcp source eq 6190 destination eq 6190
object network sharepoint
host 192.168.0.22
object network uzzpro
range 10.13.74.40 10.13.74.45
object network share
host 192.168.0.22
object-group network internalnetwork
network-object 192.168.0.0 255.255.255.0
object-group network uzzpro-1
network-object object uzzpro
access-list outside_access_in extended permit ip host 10.13.74.35 any
access-list outside_access_in_1 extended permit ip any object server
access-list outside_access_in_1 extended permit object ParagrafLex 10.15.100.0 255.255.255.0 object server
access-list outside_access_in_1 extended permit object ParagrafLex any object server
access-list outside_access_in_1 extended permit ip any object share
access-list outside_access_in_1 extended permit icmp any object sharepoint echo-reply
access-list inside_access_out extended permit ip any any
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
object network obj_any
nat (inside,outside) dynamic interface
object network server
nat (inside,outside) static 10.13.74.34
object network share
nat (any,any) static 10.13.74.39
access-group inside_access_out out interface inside
access-group outside_access_in in interface outside control-plane
access-group outside_access_in_1 in interface outside
route inside 0.0.0.0 0.0.0.0 10.13.74.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 10.13.74.0 255.255.255.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:cde649be1382dd8249eca185657d9de7
: end -
ASA 5505 Best Practice Guidance Requested
I am hoping to tap into the vast wealth of knowledge on this board in order to gain some "best practice" guidance to assist me with the overall setup using the ASA 5505 for a small business client. I'm fairly new to the ASA 5505 so any help would be most appreciated!
My current client configuration is as follows:
a) business internet service (cable) with a fixed IP address
b) a Netgear N600 Wireless Dual Band router (currently setup as gateway and used for internet/WiFi access)
c) a Cisco SG-500-28 switch
d) one server running Windows Small Business Server 2011 Standard (primary Domain Controller)
(This server is currently the DNS and DHCP server)
e) one server running Windows Server 2008 R2 (secondary Domain Controller)
f) approximately eight Windows 7 clients (connected via SG-500-28 switch)
g) approximately six printers connected via internal network (connected via SG-500-28 switch)
All the servers, clients, and printers are connected to the SG-500-28 switch.
The ISP provides the cable modem for the internet service.
The physical cable for internet is connected to the cable modem.
From the cable modem, a CAT 6 ethernet cable is connected to the internet (WAN) port of the Netgear N600 router.
A Cat 6 ethernet cable is connected from Port 1 of the local ethernet (LAN) port on the N600 router to the SG-500-28 switch.
cable modem -> WAN router port
LAN router port -> SG-500-28
The ASA 5505 will be setup with an "LAN" (inside) interface and a "WAN" (outside) interface. Port e0/0 on the ASA 5505 will be used for the outside interface and the remaining ports will be used for the inside interface.
So my basic question is, given the information above of our setup, where should the ASA 5505 be "inserted" to maximize its performance? Also, based on the answer to the previous question, can you provide some insight as to how the ethernet cables should be connected to achieve this?
Another concern I have is what device will be used as the default gateway. Currently, the Netgear N600 is set as the default gateway on both Windows servers. In your recommended best practice solution, does the ASA 5505 become the default gateway or does the router remain the default gateway?
And my final area of concern is with DHCP. As I stated earlier, I am running DHCP on Windows Small Business Server 2011 Standard. Most of the examples I have studied for the ASA 5505 utilize its DHCP functionality. I also have done some research on the "dhcprelay server" command. So I'm not quite sure which is the best way to go. First off, does the "dhcprelay server" even work with SBS 2011? And secondly, if it does work, is the best practice to use the "dhcprelay" command or to let the ASA 5505 perform the DHCP server role?
All input/guidance/suggestions with these issues would be greatly appreciated! I want to implement the ASA 5505 firewall solution following "best practices" recommendations in order to maximize its functionality and minimize the time to implement.
FYI, the information (from the "show version" command) for the ASA 5505 is shown below:
Cisco Adaptive Security Appliance Software Version 8.4(7)
Device Manager Version 7.1(5)100
Compiled on Fri 30-Aug-13 19:48 by builders
System image file is "disk0:/asa847-k8.bin"
Config file at boot was "startup-config"
ciscoasa up 2 days 9 hours
Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW016 @ 0xfff00000, 2048KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.06
Number of accelerators: 1
0: Int: Internal-Data0/0 : address is a493.4c99.8c0b, irq 11
1: Ext: Ethernet0/0 : address is a493.4c99.8c03, irq 255
2: Ext: Ethernet0/1 : address is a493.4c99.8c04, irq 255
3: Ext: Ethernet0/2 : address is a493.4c99.8c05, irq 255
4: Ext: Ethernet0/3 : address is a493.4c99.8c06, irq 255
5: Ext: Ethernet0/4 : address is a493.4c99.8c07, irq 255
6: Ext: Ethernet0/5 : address is a493.4c99.8c08, irq 255
7: Ext: Ethernet0/6 : address is a493.4c99.8c09, irq 255
8: Ext: Ethernet0/7 : address is a493.4c99.8c0a, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not used : irq 255
11: Int: Not used : irq 255
Licensed features for this platform:
Maximum Physical Interfaces : 8 perpetual
VLANs : 3 DMZ Restricted
Dual ISPs : Disabled perpetual
VLAN Trunk Ports : 0 perpetual
Inside Hosts : 10 perpetual
Failover : Disabled perpetual
VPN-DES : Enabled perpetual
VPN-3DES-AES : Enabled perpetual
AnyConnect Premium Peers : 2 perpetual
AnyConnect Essentials : Disabled perpetual
Other VPN Peers : 10 perpetual
Total VPN Peers : 12 perpetual
Shared License : Disabled perpetual
AnyConnect for Mobile : Disabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
UC Phone Proxy Sessions : 2 perpetual
Total UC Proxy Sessions : 2 perpetual
Botnet Traffic Filter : Disabled perpetual
Intercompany Media Engine : Disabled perpetual
This platform has a Base license.Hey Jon,
Again, many thanks for the info!
I guess I left that minor detail out concerning the Guest network. I have a second Netgear router that I am using for Guest netowrk access. It is plugged in to one of the LAN network ports on the first Netgear router.
The second Netgear (Guest) router is setup on a different subnet and I am letting the router hand out IP addresses using DHCP.
Basic setup is the 192.168.1.x is the internal network and 192.168.11.x is the Guest network. As far as the SBS 2011 server, it knows nothing about the Guest network in terms of the DHCP addresses it hands out.
Your assumption about the Guest network is correct, I only want to allow guest access to the internet and no access to anything internal. I like your idea of using the restricted DMZ feature of the ASA for the Guest network. (I don't know how to do it, but I like it!) Perhaps you could share more of your knowledge on this?
One final thing, the (internal) Netgear router setup does provide the option for a separate Guest network, however it all hinges on the router being the DHCP server. This is what led me to the second (Guest) Netgear router because I wanted the (internal) Netgear router NOT to use DHCP. Instead I wanted SBS 2011 to be the DHCP server. That's what led to the idea of a second (Guest) router with DHCP enabled.
The other factor in all this is SBS 2011. Not sure what experience you've had with the Small Business Server OS's but they tend to get a little wonky if some of the server roles are disabled. For instance, this is a small busines with a total of about 20 devices including servers, workstations and printers. Early on I thought, "nah, I don't need this IPv6 stuff," so I found an article on how to disable it and did so. The server performance almost immediately took a nose dive. Rebooting the server went from a 5 minute process to a 20 minute process. And this was after I followed the steps of an MSDN article on disabling IPv6 on SBS 2011! Well, long story short, I enabled IPv6 again and the two preceeding issues cleared right up. So, since SBS 2011 by "default" wants DHCP setup I want to try my best to accomodate it. So, again, your opinion/experiece related to this is a tremendous help!
Thanks!
Maybe you are looking for
-
Why do I only get the audio when I play video files?
I only receive the audio portions when I play video files. The video is blank/black. This is happening with mpg., avchd and the videos posted to websites; YouTube, Facebook etc. The only video files I can play are windows media files. Windows med
-
I need to add a try and throw an exception in an oracle package. Im refreshing a mv from local to a remote database. I need to do the following. try thrice for 15 minutes and after that throw exception while refreshing the mv. Please give me the synt
-
Hello Guys, In one of setup of oracle installation i seen physical ip and package IP for same database servers (os-solaris,oracle 10g/rel2 ) what exactly is package ip ,why it is used,how it is different from physical and logical ip i observed if i u
-
HP Deskjet and Officejet install
Hi, I have two trusty HP mobile printers which I am now struggling to set up with my new computer on Windows 7 Home Premium 64 bit. I tried to use Windows update and the CD provided but unable to install. Can anyone please help guide me to the drive
-
I dont want imessage on my macbook but i dont know how to get it off