ASA 5505 IPSec VPN Question

I have a number of ASA 5505 boxes which I need to reconfigure to work with a Watchguard XTM 850 over IPsec. The 5505s were previously configured to connect back to a 5510 Firewall using EasyVPN. With EasyVPN still enabled, the remote boxes attempt to make a connection back, but there are a few settings such as Identity and Encryption types I need to modify to connect to the Watchguard firewalls. It appears that these settings cannot be changed with EasyVPN enabled. If I disable it, and change the identity and authentication settings, the boxes do not attempt to make a connection back. I'm not sure if what I am trying to do is even possible at this point, and I am in dire need of some direction.

It is not clear from this description what is the problem and it sounds like either some part of your config changes is not correct or that there is some mismatch between your config and the config of the remote device. A starting place would be to post your config (masking off sensitive information such as public addresses and passwords.
HTH
Rick

Similar Messages

Cisco ASA 5505 Ipsec VPN and random connection dropping issues.

Hello,
We are currently having issues with a ASA 5505 Ipsec VPN. It was configured about 7-8 months ago and has been running very well..up until the last few weeks. For some reason, the VPN tends to randomly disconnect any user clients connected a lot. Furthermore, sometimes it actually connects; however does not put us on the local network for some reason and unable to browse file server. We have tried rebooting the ASA a few times and our ISP Time Warner informed us there are no signs of packet loss but still unable to pinpoint the problem. Sometimes users close out of VPN client completely, reopen several times and then it works. However it's never really consistent enough and hasn't been the last few weeks. No configuration changes have been made to ASA at all. Furthermore, the Cisco Ipsec VPN client version is: 5.0.70
Directly below is our current running config (modded for public). Any help or ideas would be greatly appreciated. Otherwise, if everything looks good...then I will defer back to our ISP Time Warner:
: Saved
ASA Version 8.4(2)
hostname domainasa
domain-name adomain.local
enable password cTfsR84pqF5Xohw. encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 205.101.1.240 255.255.255.248
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server 192.168.2.60
domain-name adomain.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network SBS_2011
host 192.168.2.60
object network NETWORK_OBJ_192.168.2.0_24
subnet 192.168.2.0 255.255.255.0
object network NETWORK_OBJ_192.168.5.192_
27
subnet 192.168.5.192 255.255.255.224
object network Https_Access
host 192.168.2.90
description Spam Hero
object-group network DM_INLINE_NETWORK_1
network-object object SPAM1
network-object object SPAM2
network-object object SPAM3
network-object object SPAM4
network-object object SPAM5
network-object object SPAM6
network-object object SPAM7
network-object object SPAM8
object-group service RDP tcp
description Microsoft RDP
port-object eq 3389
access-list outside_access_in extended permit tcp object-group DM_INLINE_NETWORK_1 object SBS_2011 eq smtp
access-list outside_access_in extended permit tcp any object SBS_2011 eq https
access-list outside_access_in extended permit icmp any interface outside
access-list outside_access_in remark External RDP Access
access-list outside_access_in extended permit tcp any object SBS_2011 object-group RDP
access-list domain_splitTunnelAcl standard permit 192.168.2.0 255.255.255.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool test 192.168.10.1-192.168.10.5 mask 255.255.255.0
ip local pool VPN_Users 192.168.5.194-192.168.5.22
0 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static NETWORK_OBJ_192.168.2.0_24
NETWORK_OBJ_192.168.2.0_24
destination static NETWORK_OBJ_192.168.5.192_
27 NETWORK_OBJ_192.168.5.192_
27 no-proxy-arp route-lookup
object network obj_any
nat (inside,outside) dynamic interface
object network SBS_2011
nat (inside,outside) static interface service tcp smtp smtp
object network Https_Access
nat (inside,outside) static interface service tcp https https
nat (inside,outside) after-auto source dynamic any interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 205.101.1.239 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-reco
rd DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.2.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.2.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.160-192.168.2.19
9 inside
dhcpd dns 192.168.2.60 24.29.99.36 interface inside
dhcpd wins 192.168.2.60 24.29.99.36 interface inside
dhcpd domain adomain interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy domain internal
group-policy domain attributes
wins-server value 192.168.2.60
dns-server value 192.168.2.60
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value domain_splitTunnelAcl
default-domain value adomain.local
username ben password zWCAaitV3CB.GA87 encrypted privilege 0
username ben attributes
vpn-group-policy domain
username sdomain password FATqd4I1ZoqyQ/MN encrypted
username sdomain attributes
vpn-group-policy domain
username adomain password V5.hvhZU4S8NwGg/ encrypted
username adomain attributes
vpn-group-policy domain
service-type admin
username jdomain password uODal3Mlensb8d.t encrypted privilege 0
username jdomain attributes
vpn-group-policy domain
service-type admin
tunnel-group domain type remote-access
tunnel-group domain general-attributes
address-pool VPN_Users
default-group-policy domain
tunnel-group domain ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:e2466a5b754
eebcdb0cef
f051bef91d
9
: end
no asdm history enable
Thanks again

Hello Belnet,
What do the logs show from the ASA.
Can you post them ??
Any other question..Sure..Just remember to rate all of the community answers.
Julio

ASA 5505 IPSEC VPN connected but can't access to LAN

ASA : 8.2.5
ASDM: 6.4.5
LAN: 10.1.0.0/22
VPN Pool: 172.16.10.0/24
Hi, we purcahsed a new ASA 5505 and try to setup IPSEC VPN via ASDM; i just simply run the Wizards, setup vpnpool, split tunnelling,etc.
I can connect to the ASA by using cisco VPN client and internet works fine on the local PC, but it cannot access to the LAN (can't ping. can't remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile i created worked fine.
Below is my configure, do I mis-configure anything?
ASA Version 8.2(5)
hostname asatest
domain-name XXX.com
enable password 8Fw1QFqthX2n4uD3 encrypted
passwd g9NiG6oUPjkYrHNt encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.1.1.253 255.255.252.0
interface Vlan2
nameif outside
security-level 0
ip address XXX.XXX.XXX.XXX 255.255.255.240
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
dns server-group DefaultDNS
domain-name vff.com
access-list vpntest_splitTunnelAcl standard permit 10.1.0.0 255.255.252.0
access-list inside_nat0_outbound extended permit ip 10.1.0.0 255.255.252.0 172.16.10.0 255.255.255.0
pager lines 24
logging enable
logging timestamp
logging trap warnings
logging asdm informational
logging device-id hostname
logging host inside 10.1.1.230
mtu inside 1500
mtu outside 1500
ip local pool vpnpool 172.16.10.1-172.16.10.254 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server AD protocol nt
aaa-server AD (inside) host 10.1.1.108
nt-auth-domain-controller 10.1.1.108
http server enable
http 10.1.0.0 255.255.252.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 10.1.0.0 255.255.252.0 inside
ssh timeout 20
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy vpntest internal
group-policy vpntest attributes
wins-server value 10.1.1.108
dns-server value 10.1.1.108
vpn-tunnel-protocol IPSec l2tp-ipsec
password-storage disable
ip-comp disable
re-xauth disable
pfs disable
ipsec-udp disable
ipsec-udp-port 10000
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpntest_splitTunnelAcl
default-domain value XXX.com
split-tunnel-all-dns disable
backup-servers keep-client-config
address-pools value vpnpool
username admin password WeiepwREwT66BhE9 encrypted privilege 15
username user5 password yIWniWfceAUz1sUb encrypted privilege 5
username user3 password umNHhJnO7McrLxNQ encrypted privilege 3
tunnel-group vpntest type remote-access
tunnel-group vpntest general-attributes
address-pool vpnpool
authentication-server-group AD
authentication-server-group (inside) AD
default-group-policy vpntest
strip-realm
tunnel-group vpntest ipsec-attributes
pre-shared-key BEKey123456
peer-id-validate nocheck
privilege cmd level 3 mode exec command perfmon
privilege cmd level 3 mode exec command ping
privilege cmd level 3 mode exec command who
privilege cmd level 3 mode exec command logging
privilege cmd level 3 mode exec command failover
privilege cmd level 3 mode exec command packet-tracer
privilege show level 5 mode exec command import
privilege show level 5 mode exec command running-config
privilege show level 3 mode exec command reload
privilege show level 3 mode exec command mode
privilege show level 3 mode exec command firewall
privilege show level 3 mode exec command asp
privilege show level 3 mode exec command cpu
privilege show level 3 mode exec command interface
privilege show level 3 mode exec command clock
privilege show level 3 mode exec command dns-hosts
privilege show level 3 mode exec command access-list
privilege show level 3 mode exec command logging
privilege show level 3 mode exec command vlan
privilege show level 3 mode exec command ip
privilege show level 3 mode exec command ipv6
privilege show level 3 mode exec command failover
privilege show level 3 mode exec command asdm
privilege show level 3 mode exec command arp
privilege show level 3 mode exec command route
privilege show level 3 mode exec command ospf
privilege show level 3 mode exec command aaa-server
privilege show level 3 mode exec command aaa
privilege show level 3 mode exec command eigrp
privilege show level 3 mode exec command crypto
privilege show level 3 mode exec command vpn-sessiondb
privilege show level 3 mode exec command ssh
privilege show level 3 mode exec command dhcpd
privilege show level 3 mode exec command vpnclient
privilege show level 3 mode exec command vpn
privilege show level 3 mode exec command blocks
privilege show level 3 mode exec command wccp
privilege show level 3 mode exec command dynamic-filter
privilege show level 3 mode exec command webvpn
privilege show level 3 mode exec command module
privilege show level 3 mode exec command uauth
privilege show level 3 mode exec command compression
privilege show level 3 mode configure command interface
privilege show level 3 mode configure command clock
privilege show level 3 mode configure command access-list
privilege show level 3 mode configure command logging
privilege show level 3 mode configure command ip
privilege show level 3 mode configure command failover
privilege show level 5 mode configure command asdm
privilege show level 3 mode configure command arp
privilege show level 3 mode configure command route
privilege show level 3 mode configure command aaa-server
privilege show level 3 mode configure command aaa
privilege show level 3 mode configure command crypto
privilege show level 3 mode configure command ssh
privilege show level 3 mode configure command dhcpd
privilege show level 5 mode configure command privilege
privilege clear level 3 mode exec command dns-hosts
privilege clear level 3 mode exec command logging
privilege clear level 3 mode exec command arp
privilege clear level 3 mode exec command aaa-server
privilege clear level 3 mode exec command crypto
privilege clear level 3 mode exec command dynamic-filter
privilege cmd level 3 mode configure command failover
privilege clear level 3 mode configure command logging
privilege clear level 3 mode configure command arp
privilege clear level 3 mode configure command crypto
privilege clear level 3 mode configure command aaa-server
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4
: end

I change a Machine's gateway to this ASA and capture again, now we can see some reply.
All ohter PCs and switches gateway are point to another ASA, maybe that's the reason why i didn't work?
what's the recommanded way to make our LAN to have two 2 gateways(for load balance or backup router, etc)?
add two gateways to all PCs and swtichwes?
1: 18:15:48.307875 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   2: 18:15:49.777685 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   3: 18:15:51.377147 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   4: 18:15:57.445777 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   5: 18:15:58.856324 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   6: 18:16:00.395090 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   7: 18:16:06.483464 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   8: 18:16:08.082805 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   9: 18:16:09.542406 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
10: 18:16:20.640424 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
11: 18:16:20.642193 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
12: 18:16:21.169607 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
13: 18:16:21.171210 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
14: 18:16:22.179556 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
15: 18:16:22.181142 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
16: 18:16:23.237673 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
17: 18:16:23.239291 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
18: 18:16:27.676402 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
19: 18:16:29.246935 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
20: 18:16:30.676921 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
21: 18:16:49.539660 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
22: 18:16:54.952602 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
23: 18:17:04.511463 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request

Asa 5505 Remote VPN Can't access with my local network

Hello Guys ,, i have a problem with my asa 5505 Remote VPN Connection with local network access , the VPn is working fine and connected , but the problem is i can't reach my inside network connection of 192.168.30.x , here is my configuration , please can you help me
ASA Version 8.2(1)
interface Vlan1
nameif inside
security-level 100
ip address 192.168.30.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 155.155.155.10 255.255.255.0
interface Vlan5
no nameif
no security-level
no ip address
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
access-list inside_nat0_outbound extended permit ip any 192.168.100.0 255.255.255.240
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn-Pool 192.168.100.1-192.168.100.10 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy mull internal
group-policy mull attributes
vpn-tunnel-protocol IPSec
username xxx password eKJj9owsQwAIk6Cw encrypted privilege 0
vpn-group-policy Mull
tunnel-group mull type remote-access
tunnel-group mull general-attributes
address-pool vpn-Pool
default-group-policy mull
tunnel-group mull ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context

Hey Jennifer i did every thing you mention it , but still i can't reach my inside network (LOCAL network) iam using Shrew Soft VPN Access Manager for my vpn connection
here is my cry ipsec sa
interface: outside
    Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: 155.155.155.1
      local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.100.1/255.255.255.255/0/0)
      current_peer:155.155.155.1, username: Thomas
      dynamic allocated peer ip: 192.168.100.1
      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
      #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: 155.155.155.1/4500, remote crypto endpt.: 155.155.155.20/4500
      path mtu 1500, ipsec overhead 82, media mtu 1500
      current outbound spi: 73FFAB96
    inbound esp sas:
      spi: 0x1B5FFBF1 (459275249)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 12288, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 2894
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
    outbound esp sas:
      spi: 0x73FFAB96 (1946135446)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 12288, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 2873
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001

Cisco ASA 5505 IPsec client VPN - Cannot connect to local hosts

I have created a Cisco IPsec vpn on my ASA using the VPN creation wizard. I am able to successfully connect to the vpn and seemingly join the network, but after I connect I am unable to connect to or ping any of the hosts on the network.
Checking the ASA I can see that a VPN session is open and my client reports that it is connected. If I attempt to ping the client from the ASA all packets are dropped.
I suspect it may be an issue with my firewall, but I am not really sure where to begin.
Here is a copy of my config, any pointers or tips are aprpeciated:
hostname mcfw
enable password Pt8fQ27yMZplioYq encrypted
passwd 2qaO2Gd6IBRkrRFm encrypted
names
interface Ethernet0/0
switchport access vlan 400
interface Ethernet0/1
switchport access vlan 400
interface Ethernet0/2
switchport access vlan 420
interface Ethernet0/3
switchport access vlan 420
interface Ethernet0/4
switchport access vlan 450
interface Ethernet0/5
switchport access vlan 450
interface Ethernet0/6
switchport access vlan 500
interface Ethernet0/7
switchport access vlan 500
interface Vlan400
nameif outside
security-level 0
ip address 58.13.254.10 255.255.255.248
interface Vlan420
nameif public
security-level 20
ip address 192.168.20.1 255.255.255.0
interface Vlan450
nameif dmz
security-level 50
ip address 192.168.10.1 255.255.255.0
interface Vlan500
nameif inside
security-level 100
ip address 192.168.0.1 255.255.255.0
ftp mode passive
clock timezone JST 9
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network DM_INLINE_NETWORK_1
network-object host 58.13.254.11
network-object host 58.13.254.13
object-group service ssh_2220 tcp
port-object eq 2220
object-group service ssh_2251 tcp
port-object eq 2251
object-group service ssh_2229 tcp
port-object eq 2229
object-group service ssh_2210 tcp
port-object eq 2210
object-group service DM_INLINE_TCP_1 tcp
group-object ssh_2210
group-object ssh_2220
object-group service zabbix tcp
port-object range 10050 10051
object-group service DM_INLINE_TCP_2 tcp
port-object eq www
group-object zabbix
port-object eq 9000
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service http_8029 tcp
port-object eq 8029
object-group network DM_INLINE_NETWORK_2
network-object host 192.168.20.10
network-object host 192.168.20.30
network-object host 192.168.20.60
object-group service imaps_993 tcp
description Secure IMAP
port-object eq 993
object-group service public_wifi_group
description Service allowed on the Public Wifi Group. Allows Web and Email.
service-object tcp-udp eq domain
service-object tcp-udp eq www
service-object tcp eq https
service-object tcp-udp eq 993
service-object tcp eq imap4
service-object tcp eq 587
service-object tcp eq pop3
service-object tcp eq smtp
access-list outside_access_in remark http traffic from outside
access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www
access-list outside_access_in remark ssh from outside to web1
access-list outside_access_in extended permit tcp any host 58.13.254.11 object-group ssh_2251
access-list outside_access_in remark ssh from outside to penguin
access-list outside_access_in extended permit tcp any host 58.13.254.10 object-group ssh_2229
access-list outside_access_in remark http from outside to penguin
access-list outside_access_in extended permit tcp any host 58.13.254.10 object-group http_8029
access-list outside_access_in remark ssh from outside to hub & studio
access-list outside_access_in extended permit tcp any host 58.13.254.13 object-group DM_INLINE_TCP_1
access-list outside_access_in remark dns service to hub
access-list outside_access_in extended permit object-group TCPUDP any host 58.13.254.13 eq domain
access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any
access-list dmz_access_in extended permit tcp any host 192.168.10.251 object-group DM_INLINE_TCP_2
access-list public_access_in remark Web access to DMZ websites (mediastudio/civicrm)
access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www
access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email)
access-list public_access_in extended permit object-group public_wifi_group any any
access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 192.168.10.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 192.168.20.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.0.80 255.255.255.240
access-list inside_nat0_outbound extended permit ip any 192.168.0.64 255.255.255.192
pager lines 24
logging enable
logging timestamp
logging buffered notifications
logging trap notifications
logging asdm debugging
logging from-address [email protected]
logging recipient-address [email protected] level warnings
logging host dmz 192.168.10.90 format emblem
logging permit-hostdown
mtu outside 1500
mtu public 1500
mtu dmz 1500
mtu inside 1500
ip local pool OfficePool 192.168.0.80-192.168.0.90 mask 255.255.255.0
ip local pool VPN_Pool 192.168.0.91-192.168.0.99 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 60
global (outside) 1 interface
global (dmz) 2 interface
nat (public) 1 0.0.0.0 0.0.0.0
nat (dmz) 1 0.0.0.0 0.0.0.0
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255
static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255
static (dmz,outside) 58.13.254.13 192.168.10.10 netmask 255.255.255.255 dns
static (dmz,outside) 58.13.254.11 192.168.10.30 netmask 255.255.255.255 dns
static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns
static (dmz,inside) 192.168.0.251 192.168.10.251 netmask 255.255.255.255
static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns
static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns
access-group outside_access_in in interface outside
access-group public_access_in in interface public
access-group dmz_access_in in interface dmz
route outside 0.0.0.0 0.0.0.0 58.13.254.9 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.0.0 255.255.255.0 inside
http 59.159.40.188 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sysopt noproxyarp dmz
sysopt noproxyarp inside
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map public_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map public_map interface public
crypto isakmp enable outside
crypto isakmp enable public
crypto isakmp enable inside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 10
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 59.159.40.188 255.255.255.255 outside
ssh 192.168.0.0 255.255.255.0 inside
ssh timeout 20
console timeout 0
dhcpd dns 61.122.112.97 61.122.112.1
dhcpd auto_config outside
dhcpd address 192.168.20.200-192.168.20.254 public
dhcpd enable public
dhcpd address 192.168.10.190-192.168.10.195 dmz
dhcpd enable dmz
dhcpd address 192.168.0.200-192.168.0.254 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
threat-detection statistics host number-of-rate 2
no threat-detection statistics tcp-intercept
ntp server 130.54.208.201 source public
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 61.122.112.97 61.122.112.1
vpn-tunnel-protocol l2tp-ipsec
group-policy CiscoASA internal
group-policy CiscoASA attributes
dns-server value 61.122.112.97 61.122.112.1
vpn-tunnel-protocol IPSec
username mcit password 4alT9CZ8ayD8O8Xg encrypted privilege 15
tunnel-group DefaultRAGroup general-attributes
address-pool VPN_Pool
default-group-policy DefaultRAGroup
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *****
tunnel-group ocmc type remote-access
tunnel-group ocmc general-attributes
address-pool OfficePool
tunnel-group ocmc ipsec-attributes
pre-shared-key *****
tunnel-group CiscoASA type remote-access
tunnel-group CiscoASA general-attributes
address-pool VPN_Pool
default-group-policy CiscoASA
tunnel-group CiscoASA ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
smtp-server 192.168.10.10
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:222d6dcb583b5f5abc51a2251026f7f2
: end
asdm location 192.168.10.10 255.255.255.255 inside
asdm location 192.168.0.29 255.255.255.255 inside
asdm location 58.13.254.10 255.255.255.255 inside
no asdm history enable

Hi Conor,
What is your local net ? I see only one default route for outside network. Dont you need a route inside for your local network.
Regards,
Umair

ASA 5505 Easy VPN to ASA 5510 Question

I am working on configuring ASA 5505's for some of our remote offices to connect to our 5510 at HQ.. I have the 5505's configured and running using Easy VPN since they will be getting their IP addresses dynamically.
From a computer connected to the ASA I can connect to and ping all of my servers at HQ. From HQ I can't ping the computer or RDP to it.
I haven't done this type of a config in years so I'm unsure of what I need to change. It seems to me that the routes aren't populating at the HQ to get to the 5505's. I was reading up on Reverse Route Injection and that seems like the right answer. I wanted to get some other ideas before I made any changes to the 5510.
Any thoughts or tips would be appreciated.
Thanks

Dan,
EzVPN might get funky sometimes. Have you looked into something like a "dynamic to static Lan to Lan" ?
If you are using EzVPN on the branch becuase you have a dynamic IP, you might want to give it a shot.
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00805733df.shtml
The config example uses a PIX 6.3 as remote, but the configuration on the remote site should be the same as any other L2L config. The one that changes is the one at the HQ where you need to configure a Default L2L group to accept the dynamic connections.
Have a good one.
Raga

Cisco ASA 5505, Cisco VPN Client and Novell Netware

Hi,
Our ISP have installed Cisco ASA 5505 firewall. We are trying to connect to our Novell 5.1 server using VPN client.
I installed VPN client on a laptop that is using wireless connection. I connect using wireless signal from near by hotel and I am able to connect to my firewall usinging vpn client and also able to login in using Novell client for XP.
When I use same vpn client and Novell client at home that is not using wireless connection, but DSL connection amd not able to login or find the tree.
The only difference in two machine is laptop using wireless connection and my home machine is using wired connection using DSL.

If your remote end of the services in question support IPsec IKEv1 as the VPN type then, yes - the 5505 can be a client for that service. At that point it looks like a regular LAN-LAN VPN which is documented in many Cisco and 3rd party how-to documents.

Cisco ASA 5505 as VPN client

Hello all thanks for looking,
I need to know how to setup my cisco asa 5505 as a vpn client to services like HMA or privateinternet and other paid VPN services. If someone else has already written a guide to this then that would be great. What I want to do is route all my secure traffice through the asa and have it go across the internet as encrypted VPN stuff and have my other stuff that does not need to be encrypted just go through to my other router.
Thanks in advance,

If your remote end of the services in question support IPsec IKEv1 as the VPN type then, yes - the 5505 can be a client for that service. At that point it looks like a regular LAN-LAN VPN which is documented in many Cisco and 3rd party how-to documents.

ASA 5505 AnyConnect VPN Can RDP to clients but can't ping/icmp

Hello all,
I've been searching all day for a solution to this problem. I setup and SSL anyconnect VPN on my Cisco ASA 5505. It works well and connects with out a problem. However, I can't ping any internal clients, but I can RDP to them. It may be something simple and I would appreciate any help. Most of the time people end up posting their config so I will as well.
MafSecASA# show run
: Saved
ASA Version 8.2(1)
hostname MafSecASA
domain-name mafsec.com
names
interface Vlan1
nameif inside
security-level 100
ip address 10.4.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 7.3.3.2 255.255.255.248
interface Vlan3
no forward interface Vlan1
nameif dmz
security-level 50
ip address 172.20.1.1 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
speed 100
duplex full
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 3
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns server-group DefaultDNS
domain-name mafsec.com
same-security-traffic permit intra-interface
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object tcp
protocol-object udp
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_2
protocol-object ip
protocol-object udp
protocol-object tcp
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_3
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_4
protocol-object ip
protocol-object icmp
access-list inside_access_in extended permit icmp any any
access-list inside_access_in extended permit ip any any
access-list inside_access_in remark allow remote users to internal users
access-list inside_access_in remark allow remote users to internal users
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_4 10.4.0.0 255.255.255.0 10.5.0.0 255.255.255.0
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_3 10.5.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list outside_access_in extended permit icmp any any
access-list inside_split_tunnel standard permit 10.4.0.0 255.255.255.0
access-list inside_split_tunnel standard permit 10.5.0.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.4.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.4.0.0 255.255.255.0 10.5.0.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.5.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 10.4.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 10.4.0.0 255.255.255.0 10.5.0.0 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 10.5.0.0 255.255.255.0 10.4.0.0 255.255.255.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu dmz 1500
ip local pool SSLVPNPool2 10.5.0.1-10.5.0.254 mask 255.255.255.0
ip verify reverse-path interface outside
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound_1
nat (inside) 1 0.0.0.0 0.0.0.0
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 7.3.3.6 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication enable console LOCAL
aaa authentication ssh console LOCAL
http server enable
http 10.4.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 10
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 10.4.0.0 255.255.255.0 inside
ssh timeout 5
ssh version 2
console timeout 0
dhcpd option 6 ip 8.8.8.8 8.8.4.4
dhcpd address 10.4.0.15-10.4.0.245 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd lease 86400 interface inside
dhcpd option 3 ip 10.4.0.1 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
svc image disk0:/anyconnect-win-2.5.3055-k9.pkg 1
svc image disk0:/anyconnect-macosx-i386-2.5.3055-k9.pkg 2
svc enable
tunnel-group-list enable
group-policy SSLVPN internal
group-policy SSLVPN attributes
dns-server value 8.8.8.8 8.8.4.4
vpn-tunnel-protocol svc
group-lock none
split-tunnel-policy tunnelspecified
split-tunnel-network-list value inside_split_tunnel
vlan none
address-pools value SSLVPNPool2
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
username user1 password
username user1 attributes
service-type remote-access
username user2 password
tunnel-group SSLVPNGROUP type remote-access
tunnel-group SSLVPNGROUP general-attributes
address-pool SSLVPNPool2
default-group-policy SSLVPN
tunnel-group SSLVPNGROUP webvpn-attributes
group-alias SSLVPN enable
prompt hostname context
Cryptochecksum:3b16cbc9bbdfa20e6987857c1916a396
: end
Thank in advance for any help!

Your config actually looks good (you have the ACL that would allow the echo-reply back since you don't have inspection turned on) - are you sure this isn't a windows firewall issue on the PCs? I'd try pinging a router or switch just to make sure.
--Jason

Asa 5505 Ipsec/ipad configuration

Hey Got some issues when setting up IPSEC/VPN on the asa 5505. I want to connect from the ipad with the built in IPSec client..
Get these errors when i run the debug crypto isakmp
Jan 28 22:03:26 [IKEv1]: Group = VPN_ipad, Username = Haq, IP = x.x.x.x, Tunnel Rejected: Conflicting protocols specified by tunnel-group and group-policy
Jan 28 22:03:26 [IKEv1]: Group = VPN_ipad, Username = Haq, IP = x.x.x.x, QM FSM error (P2 struct &0xd5d5f3d8, mess id 0x295bc3a)!
Jan 28 22:03:26 [IKEv1]: Group = VPN_ipad, Username = Haq, IP = x.x.x.x, Removing peer from correlator table failed, no match!
There is a bunch of vpn site-to-site and ipsec vpn profiles setup and those works fine..?
Here is the running config sh run crypto:
crypto ipsec transform-set DES esp-des esp-md5-hmac
crypto ipsec transform-set 3DES-TRANS esp-3des esp-sha-hmac
crypto ipsec transform-set 3DES-TRANS mode transport
crypto ipsec transform-set AES esp-aes esp-sha-hmac
crypto ipsec transform-set 3des esp-3des esp-md5-hmac
crypto ipsec transform-set IPAD-IPSEC esp-3des esp-sha-hmac
crypto ipsec transform-set IPAD-IPSEC mode transport
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map Plandent 10 set transform-set ESP-AES-128-SHA ESP-AES-256-SHA ESP-AES-128-MD5 ESP-AES-256-MD5 DES 3des 3DES-TRANS
crypto dynamic-map Plandent 10 set security-association lifetime seconds 84600
crypto dynamic-map Plandent 10 set security-association lifetime kilobytes 300000
crypto dynamic-map IPAD-MAP 5 set transform-set IPAD-IPSEC
crypto dynamic-map IPAD-MAP 5 set security-association lifetime seconds 28800
crypto dynamic-map IPAD-MAP 5 set security-association lifetime kilobytes 4608000
crypto map PD_VPN 10 match address ToGoteborg
crypto map PD_VPN 10 set peer PixGoteborg
crypto map PD_VPN 10 set transform-set DES
crypto map PD_VPN 10 set security-association lifetime seconds 84600
crypto map PD_VPN 10 set security-association lifetime kilobytes 4608000
crypto map PD_VPN 20 match address ToMalmo
crypto map PD_VPN 20 set peer PixMalmo
crypto map PD_VPN 20 set transform-set DES
crypto map PD_VPN 20 set security-association lifetime seconds 84600
crypto map PD_VPN 20 set security-association lifetime kilobytes 4608000
crypto map PD_VPN 30 match address ToPlanmeca
crypto map PD_VPN 30 set peer ASA_HKI ASA_HKI_BACKUP
crypto map PD_VPN 30 set transform-set AES
crypto map PD_VPN 30 set security-association lifetime seconds 86400
crypto map PD_VPN 30 set security-association lifetime kilobytes 4608000
crypto map PD_VPN 100 ipsec-isakmp dynamic Plandent
crypto map PD_VPN interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 10
authentication pre-share
encryption aes
hash sha
group 2
lifetime 28800
crypto isakmp policy 30
authentication pre-share
encryption des
hash md5
group 2
lifetime 86400
Anyone have any tips and tricks on what can be wrong here, will really be appreciated
Thanks
Shane

Well i created a new tunnel-group and a new group policy its still give me this error? that the tunnel is rejected:
Conflicting protocols specified by tunnel-group and group-policy
But as you can see the ipsec is allowed?
tunnel-group PLANDENT_IPAD type remote-access
tunnel-group PLANDENT_IPAD general-attributes
address-pool IPAD_VPN
default-group-policy PLANDENT_IPAD_Policy
tunnel-group PLANDENT_IPAD ipsec-attributes
pre-shared-key *
group-policy PLANDENT_IPAD_Policy internal
group-policy PLANDENT_IPAD_Policy attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPN_ipad_splitTunnelAcl
/Shane

CIsco ASA 5505 and VPN licenses

Hi,
Cisco ASA 5505 comes with 10 VPN licenses in a standard configuration.
How those licenses are counted? Will I need a license per one IPSec SA?
If I have two site connected with LAN-to-LAN VPN with 10 subnets at one site, how many licenses will be taken? 10 - one per IPSec SA or just 1 - one per point-to-point VPN?
Thank you.
Regards,
Alex

Alex,
In an ASA 5505, it should say something like this...when you do sh ver.
VPN Peers : 25
It means that you can have so many peers connecting to the ASA. Its not per IPSec SA.
Its a per tunnel license.
Rate this, if it helps!
Gilbert

Cisco ASA 5505 SSL VPN

Hi Everyone,
In my study home lab, I wanted to configure a cisco ASA 5505 ( Base license) to allow SSL VPN. I follow carefully the configuration procedure as instructed on a short videos I downloaded on youtube.
I configured my outside e0/0 with a valid static IP address, unfortunately the vpn connection is timeout on a remote ( different) internet connection. But if I connect to my own internet line using a WIFI the VPN ( AnyConnect SSL VPN client ) connection is established.
I need help to solve this mystery. Please find attached the ASA config: #show run
I hope my explaination does make sense, if not accept my apology I am just new in cisco technology.
Best regards,
BEN

If you can connect with your own internet line, then most probably it's not an issue with the ASA configuration.
I would check how you are routing the ASA to the internet, and if there is any ACL that might be blocking inbound access to the ASA on the device in front of the ASA.

Unable to ping device behind Cisco 3750 on the same inside VLAN via Cisco ASA 5505 Anyconnect VPN

Hi Guys,
I've been stuck with this for the last 2 days, and I thought to try and use Cisco's forum, I setup my home DC, and started having problems once I moved a Cisco 5505 behind a Cisco 1841 router (I wanted to eventually test DMVPN live on the internet,) I was no longer able to ping some devices, then as soon as I introduce a collapsed core/distribution switch, I'm also no longer able to ping the devices behind the Cisco 3750, I've attached a network diagram and the ASA running-config.
Everything seem fine internally with the exception of an intermittent network connectivity with a Citrix NetScaler VPX running on a VMware ESXi.
For some odd reason, I am able to ping the following, with no issues.
Cisco 3750 SVI (192.168.1.3)
CentOS web server (connected directly to the Cisco ASA 5505)
I have checked and enable the following:
Nat Exemption
Sysopt connection permit-vpn
ACL's
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
Added ICMP in the inspection policy
Packet-capture - Only getting echo requests.
Thanks in advance!

Hi,
I believe you have the problem with your no-nat configurations..... you to exempt NAT for the traffic from 172.16.10.0 (Anyconnect VPN pool) to 192.168.1.0/24 (Inside LAN) to make this work
object network acvpnpool
subnet <anyconnect VPN Subnet>
object network insidelan
subnet <inside lan subnet>
nat (inside,outside) source static acvpnpool acvpnpool destination static insidelan insidelan
Make sure that you are able to reach the GW/Inside ip adress of the firewall from LAN machine.... all routing in place properly..... Thanks!!!
Regards
Karthik

Cisco ASA 5505 IPSEC, one endpoint behind NAT device

We have two Cisco ASA 5505 devices.
Both are identical, however, one of them is behind a NAT device.
We are attempting to create an IPSEC network.
Site fg:
<ipsec subnet1> -- ASA 5505 (ASA1) -- <internet>
ASA1: 10.1.1.2/24 (inside), 212.xxx.xxx.xxx/28 (outside)
Site be:
<ipsec_subnet2> -- ASA 5505 (ASA3) -- Zywall USG (USG1) -- <internet>
ASA3: 10.1.4.1/24 (inside), 192.168.4.50/24 (outside)
USG1: 192.168.4.100/24 (inside), 195.xxx.xxx.xxx/30 (outside)
USG1: UDP port 500/4500 forwarded to 192.168.4.50
It seems that ASA1 stops the procedure (we verified this with debug crypto isakmp 254):
Group = 195.xxx.xxx.xxx, IP = 195.xxx.xxx.xxx, QM FSM error (P2 struct &0xd1111cd8, mess id 0x81111a78)!
Group = 195.xxx.xxx.xxx, IP = 195.xxx.xxx.xxx, Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 192.168.4.50/255.255.255.255/0/0 local proxy 212.xxx.xxx.xxx/255.255.255.255/0/0 on interface outside
Group = 195.xxx.xxx.xxx, IP = 195.xxx.xxx.xxx, PHASE 1 COMPLETED
We verified / attempted the following:
- NAT excemption on both sides for IPSEC subnets
- Mirror image crypto maps
- Disabled IKE peer ID validation (yes, pre-shared key but we ran out of ideas)
- Toggled between static to dynamic crypto maps on ASA1
Most search results turned up results referring to the incorrect settings of the crypto map or the lack of NAT excemption.
Does anyone have any idea?
195.txt contains show running-config of ASA3
212.txt contains show running-config of ASA1
log.txt contains somewhat entire log snipper of ASA1

Hi,
on 212 is see
tunnel-group 195.xxx.xxx.xxx type ipsec-l2l
tunnel-group 195.xxx.xxx.xxx ipsec-attributes
pre-shared-key
When you define the peer with static tunnel-group entry ASA is looking for peer configuration in static crypto map. If the peer is behind static NAT configure a proper static crypto map with matching acl and proposals.
If the peer is behind dynamic nat refer this example :http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/81883-ipsec-iosrtr-dyn-pix-nat.html
Regards,
Abaji.

ASA 5505 ssh access question

Hi,
Currently any ip address can ssh to my asa 5505 firewall outside interface. What should I do to restrict only certain IP can? What's the command to see the current ssh management access rule?
Thanks.
Ye

I tried this and got an error. Please help.
CL-T179-12IH# ssh 162.221.204.59 255.255.255.255 outside
^
ERROR: % Invalid input detected at '^' marker.
Also when I do "show run ssh" I see below line. How to remove it?
ssh 0.0.0.0 0.0.0.0 outside
Thanks.
Ye

ASA 5505 IPSec VPN Question

Similar Messages

Maybe you are looking for