ASA 5505 VPN licensing question

I have three locations, that i want to connect via site-to-site vpn's deployed on three ASA 5505. How is the term "Peers" in the licensing text, affecting my scenario? Is each ASA one peer in a site-to-site solution, or is each user transmitting data in the established tunnels also counted?

Users transmitting across the site to site tunnel are not counted. Only the peers themselves.

Similar Messages

  • ASA 5505 VPN configuration question

    I have a asa 5505 v7.2(3) asdm 5.2(3) th I am trying to get reconfigured after our cable company was bought out and they replaced the cable modem with a router. My asa now has a non routable "10" address on the outside instead of one of the 5 statics I have assigned to me. I have natted my servers, but I cannot get my vpn clients connected. I am not sure how to get one of my statics assigned to the asa to use for the VPN tunnel. Used to be I just tunneled to the static "outside" address with my Cisco VPN clients (remote pc's). I tried assigning one of my statics to the outside, but then I had no connectivity at all since there is a router now before me, where it was just a modem before. I am used to working on larger pix's with my own IP address range, and not used to dealing with DHCP assigned outside addresses, so I am sure it is something simple I am missing. Any help would be greatly appreciated, this is for a small charity animal shelter, that has been down since the cable company made their "transparent change" when the bought another one out.
    The ISP router has an interface with one of my static on the outside facing interface, and a 10 address on the interface directly connected to my ASA. The ISP router then assigns a 10 address to my outside interface on the ASA. I then have 192 addresses on my inside interfaces with statics for their servers. I am just not sure now how to connect my VPN clients since I do not have a routable outside address anymore. I have tried connecting to the static on the ISP hinking they might pass the packet, but they don't. I thought maybe a loopback could be assigned to the ASA, but could not see a way to do that. also the ethernet interfaces cannot have address assigned, only vlans, which there can only be two, and both are used (inside, outside) so I am out of ideas.
    Thanks for any help
    Thanks much

    Hi Kevin
    Your current design causes administrative overhead. You either need one-to-one mapping with outside int or a PAT which is forwarding UDP 4500 and TCP 10000 (may cause troubles in GRE)
    Ask your ISP to configure the router in bridged mode and let your outside interface have the public IPs instead 10.x.x.x
    Regards

  • Cisco ASA 5505 - Base License

    Hello to everyone
    I having this kind of config and in my network were workig flawless but in the site installed is giving me trouble.
    First my conection to the site is working so i can access from the internet to the ASA, but I cant do inter-vlan routing in the ASA.
    I have activated those commands and nothing i cant not ping to my vlan2 interface from my inside: I do not have a router making the L3 routing only the ASA but it could let me pass traffic because the ASA is a L3 device. alsa this licence has no trunk.
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    Well I have do many things and nothing,
    policy-map global_policy
    class inspection_default
    inspect icmp
    not results, waiting for your comments.
    Licensed features for this platform:
    Maximum Physical Interfaces    : 8
    VLANs                          : 3, DMZ Restricted
    Inside Hosts                   : 10
    Failover                       : Disabled
    VPN-DES                        : Enabled
    VPN-3DES-AES                   : Enabled
    SSL VPN Peers                  : 2
    Total VPN Peers                : 10
    Dual ISPs                      : Disabled
    VLAN Trunk Ports               : 0
    Botnet Traffic Filter          : Disabled
    ASA Version 8.2(5)
    hostname ASA5505
    enable password XXXXXXXXXXXXXX encrypted
    passwd XXXX.XXXXXXXX encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 100
    ip address 10.0.0.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address XX.XX.XX.174 255.255.255.248
    ftp mode passive
    pager lines 24
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    global (outside) 10 interface
    nat (inside) 10 10.0.0.0 255.255.255.0
    route outside 0.0.0.0 0.0.0.0 XX.XX.XX.169 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    aaa authentication ssh console LOCAL
    aaa authentication http console LOCAL
    http server enable
    http 0.0.0.0 0.0.0.0 outside
    http 10.0.0.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    telnet timeout 5
    ssh 10.0.0.0 255.255.255.0 inside
    ssh 0.0.0.0 0.0.0.0 outside
    ssh timeout 5
    console timeout 0
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    username root password XXXXXXXXX encrypted privilege 15
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect ip-options
      inspect netbios
      inspect rsh
      inspect rtsp
      inspect skinny
      inspect esmtp
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect sip
      inspect xdmcp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:0c8a226f7c4a8d5a03e6fcd821893898
    : end

    Cisco ASA 5505 Base License - not inter-vlan-routing no internet access from inside interface
    here the output from my pings
    ping
    Interface: inside
    Target IP address: 10.0.0.1
    Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:
    Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
    ASA5505# ping
    Interface: outside
    Target IP address: 66.XX.XX.174
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 66.XX.XX.174, timeout is 2 seconds:
    Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
    ASA5505# ping
    Interface: inside
    Target IP address: 66.XX.XX.174
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 66.XX.XX.174, timeout is 2 seconds:
    Success rate is 0 percent (0/5)
    ASA5505# ping
    Interface: outside
    Target IP address: 10.0.0.1
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:
    Success rate is 0 percent (0/5)
    So inter-vlan routing is not wowrking after I have to use the followings commands to see if there any change but not results
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    policy-map global_policy
    class inspection_default
    inspect icmp
    exit
    exit
    service-policy global_policy global
    After all the thing i've done in CLI I logged into the ASDM and in the nat section i look that nat was not having destination.
    global (outside) 10 interface
    nat (inside) 10 10.0.0.0 255.255.255.0
    so I decide to apply in this way
    global (outside) 1 interface
    nat (inside) 1 access-list inside_nat_outbound
    and voila everything is working i was able to ping 4.2.2.2 to the outside, I think that the problem is with the public ip directly assigned to  the ASA by iSP and not the private ip, because in my test enviorement was working perfectly and i was using 192.168.0.0 and 172.18.0.0 networks as the outside interface ip and everything was fine.
    But thanks to all that help now have to start to apply security and acls configs.

  • VPN License question on 5505 ASA Firewall

    Inherited a firewall project, it's getting a VPN running on a ASA 5505 Firewall for remote workers.  Firewall was configured by someone else who isn't available. 
    Basic question on the License: The current license is good for 2 SSL VPN Peers, and 20 "Total VPN Peers".  Can anyone elaborate on "Total VPN Peers"?  Can I configure Clientless SSL VPN connections, or do I need to go IPSec to get the 20 VPN sessions?
    Thank you in advance,
    Jeff

    Hi Linda,
    The default IKE SA lifetime is 86,400 seconds and the default IPSEC SA lifetime is 28,800 seconds. However, these values are configurable so you'll need to check your 5505 configuration to answer these questions. You can look at the output of 'show run crypto' to see the configured values.
    -Mike

  • Cisco ASA 5505 VPN Routing/Networking Question

    I have a very basic question about Cisco ASA 5505 IPsec Site to Site VPNs.  I want to install a Cisco ASA 5505 at a Data Center, in a LAN subnet that utilizes publicly routable IP addresses.  I would like to install a second Cisco ASA 5505 in a remote branch office as its peer. 
    Regardless of whether I use publicly routable IPs at the branch office in the "inside" network or non-routable IPs, how would the devices and servers at the Data Center know to route IP packets destined for the branch office back through the Cisco ASA instead of through the default gateway at the Data Center?  I can see accomplishing this if every single device at the Data Center is configured with routing table entries, but that isn't feasible.  It also isn't feasible to use the Cisco ASA 5505 as the default gateway for all of the devices as the Data Center, allowing it to decide where the traffic should go.
    What am I missing?  Is the solution to try to map branch office IPs to IP addresses within the Data Center's LAN subnet so that all of the traffic is on the same subnet?

    You can do it in several different ways.
    One way is to tell the server that if it has traffic to network x then it needs to go to the ASA all other traffic is to head for the default gateway.
    In windows this is done via the route command
    do not forget to make it "persistent" otherwise the route will disapear when your reboot the server.
    in unix/linux
    It is also the route command
    Or you can tell your "default gateway" to route that network to the ASA
    Good luck
    HTH

  • ASA 5505 VPN Ping Problems

    Hello everyone,
    First off, I apologize if this is something that I can google. My knowledge of network administration is all self-taught so if there is a guide to follow that I've missed please point me in the right direction, its often hard to Google terms for troubleshooting when your jargon isn't up to snuff.
    The chief issue is that when pinging internal devices while connected to the results are very inconsistent.
    Pinging 192.168.15.102 with 32 bytes of data:
    Reply from 192.168.15.102: bytes=32 time=112ms TTL=128
    Request timed out.
    Request timed out.
    Request timed out.
    We've set up a IPSec VPN connection to a remote Cisco ASA 5505. There are no issues connecting, connection seems constant, packets good etc. At this point I can only assume I have configuration issues but I've been looking at this for so long, and coupled with my inexperience configuring these settings I have no clue where to start. My initial thoughts are that the LAN devices I am pinging are not sending their response back or the ASA doesn't know how to route packets back?
    Here's a dump of the configuration:
    Result of the command: "show config"
    : Saved
    : Written by enable_15 at 12:40:06.114 CDT Mon Sep 9 2013
    ASA Version 8.2(5)
    hostname VPN_Test
    enable password D37rIydCZ/bnf1uj encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    name 192.168.15.0 internal-network
    ddns update method DDNS_Update
    ddns both
    interval maximum 0 4 0 0
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    description VLAN to inside hosts
    nameif inside
    security-level 100
    ddns update hostname 0.0.0.0
    ddns update DDNS_Update
    dhcp client update dns server both
    ip address 192.168.15.1 255.255.255.0
    interface Vlan2
    description External VLAN to internet
    nameif outside
    security-level 0
    ip address xx.xx.xx.xx 255.255.255.248
    ftp mode passive
    clock timezone CST -6
    clock summer-time CDT recurring
    dns server-group DefaultDNS
    name-server 216.221.96.37
    name-server 8.8.8.8
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    object-group service DM_INLINE_TCP_1 tcp
    port-object eq www
    port-object eq https
    access-list outside_access_in extended permit icmp any any
    access-list outside_access_in extended deny icmp interface outside interface inside
    access-list outside_access_in extended permit ip 192.168.15.192 255.255.255.192 any
    access-list Remote_splitTunnelAcl standard permit internal-network 255.255.255.0
    access-list inside_nat0_outbound extended permit ip internal-network 255.255.255.0 192.168.15.192 255.255.255.192
    access-list inside_access_in remark Block Internet Traffic
    access-list inside_access_in extended permit ip 192.168.15.192 255.255.255.192 any
    access-list inside_access_in remark Block Internet Traffic
    access-list inside_access_in extended permit ip interface inside interface inside
    access-list inside_access_in extended permit ip any 192.168.15.192 255.255.255.192
    access-list inside_access_in remark Block Internet Traffic
    access-list inside_nat0_outbound_1 extended permit ip 192.168.15.192 255.255.255.192 any
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip local pool VPN_IP_Pool 192.168.15.200-192.168.15.250 mask 255.255.255.0
    ipv6 access-list inside_access_ipv6_in permit ip interface inside interface inside
    icmp unreachable rate-limit 1 burst-size 1
    icmp permit any inside
    icmp permit any echo-reply outside
    icmp permit any outside
    no asdm history enable
    arp timeout 14400
    nat-control
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 0 access-list inside_nat0_outbound_1 outside
    nat (inside) 1 192.168.15.192 255.255.255.192
    nat (inside) 1 0.0.0.0 0.0.0.0
    access-group inside_access_in in interface inside
    access-group inside_access_ipv6_in in interface inside
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 xx.xx.xx.xx 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    http internal-network 255.255.255.0 inside
    http yy.yy.yy.yy 255.255.255.255 outside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    sysopt connection timewait
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    management-access inside
    dhcpd auto_config outside
    dhcpd address 192.168.15.200-192.168.15.250 inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection statistics access-list
    threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
    ntp server 192.168.15.101 source inside
    ntp server 192.168.15.100 source inside prefer
    webvpn
    group-policy Remote internal
    group-policy Remote attributes
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value Remote_splitTunnelAcl
    username StockUser password t6a0Nv8HUfWtUdKz encrypted privilege 0
    username StockUser attributes
    vpn-group-policy Remote
    tunnel-group Remote type remote-access
    tunnel-group Remote general-attributes
    address-pool VPN_IP_Pool
    default-group-policy Remote
    tunnel-group Remote ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny 
      inspect sunrpc
      inspect xdmcp
      inspect sip 
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:f4271785b86e45dd3a17bab8f60cd2f3

    Hi Graham,
    My first question is do you have a site to site VPN or Remote access client VPN.
    After checking your configuration i see that you do not have any Site to SIte VPN configuration so i am assuming that you ara facing issue with the VPN client.
    And if i understood correctly you are able to connect the VPN client but you not able to access the internal resources properly.
    I would recommend you to tey and make teh following changes.
    Remove the following configuration first:
    nat (inside) 0 access-list inside_nat0_outbound_1 outside
    nat (inside) 1 192.168.15.192 255.255.255.192
    You do not need the 1st one and i do not understand the reason of the second one
    Second one is your pool IP subnet (192.168.15.200-192.168.15.250) and i am not sure why you have added this NAT.
    If possible change your Pool subnet all together because we do not recommend to use th POOL ip which is simlar to your local LAN.
    Try the above changes and let me know in case if you have any issue.
    Thanks
    Jeet Kumar

  • ASA 5505 VPN can't access connected network

    I have an ASA 5505 with ipsec VPN configured on it.  I am able to  connect to the ASA but I can't ping a connected network.  I get a dhcp  assigned address in the network I am trying to reach but can't access  that network on Vlan5.  Please help.
    I attached the config.

    I think final questions, can you have two nat statements that point to the same acl ie.
    access-list no_nat extended permit ip 192.168.9.0 255.255.255.0 192.168.0.0 255.255.255.0
    access-list no_nat extended permit ip 192.168.9.0 255.255.255.0 172.31.1.0 255.255.255.0
    access-list no_nat extended permit ip 192.168.5.0 255.255.255.0 192.168.5.0 255.255.255.0
    nat (inside) 0 access-list no_nat
    nat (inside) 1 192.168.9.0 255.255.255.0
    nat (fw-civic) 0 access-list no_nat
    nat (fw-civic) 1 192.168.5.0 255.255.255.0
    Or do I need to create a new acl for the fw-civic interface?
    Thanks

  • ASA 5505 VPN NEM

    Hi! First of all I appologize for posting a similar question in another forum. I think this one is the right place.
    Im trying to connect to a PIX 501 with easy vpn in nem mode with a ASA 5505. Currently running 7.2.2-22 (had to download a interim release due to dhcp problems with the ISP in 7.2.2) and ASDM 5.2.
    The problem is that when using nem mode i cannot ping the other side at all. When using client mode this works fine but i need the two way traffic.
    Our Head unit is 192.168.1.1 and the connecting ASA 5505 is 192.168.10.1. When I try to ping a machine (192.168.1.201) from the remote site I get this in the ASA log:
    With network extension mode
    302020 192.168.1.201 192.168.10.2 Built ICMP connection for faddr 192.168.1.201/0 gaddr 192.168.10.2/512 laddr 192.168.10.2/512
    With only client mode
    302020 192.168.1.201 192.168.10.2 Built ICMP connection for faddr 192.168.1.201/0 gaddr 192.168.1.9/1 laddr 192.168.10.2/512
    It seemes to me that the ASA sets an incorrect gateway address in nem mode ?
    The PIX 501 has been working fine for some years with software clients connecting.
    Any ideas ?
    Thanks!

    When configured in Easy VPN Network Extension Mode, the ASA 5505 does not hide the IP addresses of local hosts by substituting a public IP address. Therefore, hosts on the other side of the VPN connection can communicate directly with hosts on the local network.
    Try this link:
    http://www.cisco.com/en/US/docs/security/asa/asa72/configuration/guide/site2sit.html

  • ASA 5505 VPN Connection Issue

    Good morning everyone,
    At my last position I was IT Director whose area of expertise was database and application development. All of the company's networking planning and maintainence I entrusted to my sysadmin, Salvadore. Back in 2004 we began implementing major changes in the network. Salvadore recommended SonicWALL firewalls. He did a fantastic job of securing our valuable server assets. Among the many improvements Salvadore established VPN access to the datacenter assets for mobile employees. What I remember especially well was the ease-of-use: start the VPN Client then RDP to a server or connect with SQL Server, in addition to connecting to all devices on my home network. It was absolutely beautiful!
    Fast forward to today. I have since retired. I do a little bit of daytrading on the side for entertainment. I leased a dedicated server to run an application that runs continuously 24 hours a day, 5 days a week. I contacted Salvadore to do a security audit on the server. As expected the server was under constant assault by bots trying to hack the RDP port. Salvadore recommended a firewall. The datacenter host offered us two choices of Cisco firewalls, one of which we chose: ASA 5505.
    Today I have a secure server which pleases me. The one thing that bothers me however is that I lose access to my home network devices while the VPN Client is connected. Here are the symptoms:
    I cannot send an email with Outlook as I normally do by relaying off of my Internet provider's SMTP server.
    I cannot connect to the TradeStation servers with my TradeStation application using login credentials that are authorized for my home network only.
    I cannot access my Seagate network storage drive.
    This is what I discovered:
    My wireless adapter (which I use from this laptop) identifies itself as "Wireless LAN adapter Wireless Network Connection" in IPCONFIG. IPv4 address is 192.168.0.5. Default Gateway: 192.168.0.1.
    After I connect the VPN Client, IPCONFIG reports a new adapter: "Ethernet adapter Local Area Connection 2". IPv4 address is 10.0.10.4. Default Gateway: 10.0.10.1.
    When I launch Windows Task Manager and click on the Networking tab, I see those two adapters.
    When launch IE and go to bandwidthplace.com to run a test, I see all of the network traffic going over "Ethernet adapter Local Area Connection 2".
    When I disconnect VPN and then rerun the bandwidth test, I see that all of the network traffic now goes over "Wireless LAN adapter Wireless Network Connection".
    This explains all of the symptoms:
    My Internet Provider will only allow me to relay off of their email servers if I am connected to their network.
    TradeStation refuses connection to their network because my credentials do not match my network address.
    There is no Seagate network storage device on the remote server network.
    My questions to the Cisco Support Community are:
    Is this the best I can hope for?
    Must all traffic be routed through the VPN connection?
    Is there any way to route traffic destined for 10.0.*.* through VPN and everything else through the default connection?
    Thank you everyone for your help. I would be happy to provide additional detailed information.

    Hi Brian,
    you can route traffic destined to 10.0.*.* over the VPN and keep normal internet traffic unencrypted over the default connection - this setup is known as VPN Split Tunnelling.
    This doc shows how to setup the access control list and apply this to the tunnel policy.
    Hope this helps
    http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080702999.shtml

  • ASA 5505 & VPN Cellular connection

    We have a ASA 5505 setup with VPN and using Cisco client 5.0. The VPN works without a problem if we use normal internet access (from home, motel, etc). However if we use a cellular wi-fi hotspot or tether a phone it will connect to the vpn but will not allow us to get on the office network. Anyone have this problem or know a solution

    Hello greentw1972,
    I have ran in to this issue several times. This is mainly caused by Cisco VPN client's compatibility issues with the 3G-Dongle/Tethering-device. I have seen several workarounds for this but the best one I have found is to use a Open source vpn client.
    I have used Shrewsoft VPN client and it has worked nicely without any issues so far
    Find the links below for further information.
    The 3rd link will show you how exactly you need to transfer information from Cisco VPN client to Shrewsoft client.
    Shrewsoft latest VPN client download link : www.shrew.net/download/vpn/vpn-client-2.2.0-rc-2.exe
    Shrewsoft Web site : www.shrew.net
    Installation instruction as Cisco VPN alternative : http://superuser.com/questions/312947/how-to-configure-shrewsoft-vpn-to-connect-to-cisco-vpn-server
    Plese rate this post if helpful

  • ASA 5505 vpn/OWA issue

    I have a client that is running Win2003 Server R2 with Exchange Server 2003. OWA was setup and clients could connect to their exchange mailbox from the internet with no problems.
    We recently configured vpn on the ASA 5505 and now no-one can connect to OWA since that time.
    Any thoughts?

    Have you been using the ASDM to configure the VPN? In that case, you may have removed the required portforwarding or modified the access-list that allows traffic from the outside.
    regards,
    Leo

  • ASA 5505 VPN can't access inside host

    I have setup remote VPN access on a ASA 5505 but cannot access the host or ASA when I login using the VPN. I can connect with the Cisco VPN client and the VPN light is on on the ASA and it shows that I'm connected. I have the correct Ip address but I cannot ping or connect to any of the internal addresses. I cannot find what I'm missing. I have the VPN bypassing the interface ACLs. Since I can login but not go anywhere I feel certian I missed something.
    part of config below
    interface Vlan1
    nameif inside
    security-level 100
    ip address 10.1.1.1 255.255.255.0
    ip local pool xxxx 10.1.1.50-10.1.1.55 mask 255.255.255.0
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto dynamic-map outside_dyn_map 20 set pfs
    crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
    crypto dynamic-map outside_dyn_map 40 set pfs
    crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-SHA
    crypto dynamic-map inside_dyn_map 20 set pfs
    crypto dynamic-map inside_dyn_map 20 set transform-set ESP-3DES-SHA
    crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
    crypto map outside_map interface outside
    crypto map inside_map 65535 ipsec-isakmp dynamic inside_dyn_map
    crypto map inside_map interface inside
    crypto isakmp enable inside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    service-policy global_policy global
    group-policy xxxxxxx internal
    group-policy xxxxxxx attributes
    banner value xxxxx Disaster Recovery Site
    wins-server none
    dns-server value 24.xxx.xxx.xx
    vpn-access-hours none
    vpn-simultaneous-logins 3
    vpn-idle-timeout 30
    vpn-session-timeout none
    vpn-filter none
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelall
    default-domain none
    secure-unit-authentication disable
    user-authentication disable
    user-authentication-idle-timeout none
    ip-phone-bypass disable
    leap-bypass disable
    nem disable
    nac disable
    nac-sq-period 300
    nac-reval-period 36000
    nac-default-acl none
    address-pools value xxxxxx
    smartcard-removal-disconnect enable
    client-firewall none
    webvpn
    functions url-entry
    vpn-nac-exempt none
    no vpn-addr-assign aaa
    no vpn-addr-assign dhcp
    tunnel-group xxxx type ipsec-ra
    tunnel-group xxxx general-attributes
    address-pool xxxx
    default-group-policy xxxx
    tunnel-group blountdr ipsec-attributes
    pre-shared-key *

    I get the banner and IP adress info...
    This is what the client log provides...
    1 13:45:32.942 05/30/08 Sev=Warning/2 CVPND/0xE3400013
    AddRoute failed to add a route: code 87
    Destination 172.20.255.255
    Netmask 255.255.255.255
    Gateway 10.1.2.1
    Interface 10.1.2.5
    2 13:45:32.942 05/30/08 Sev=Warning/2 CM/0xA3100024
    Unable to add route. Network: ac14ffff, Netmask: ffffffff, Interface: a010205, Gateway: a010201.

  • ASA 5505 & VPN Client blocking access to local lan

    I have setup a IPSec vpn client connection to a Cisco ASA 5505, when I connect to the unit it fully authenticates and issues me an ip address on the local lan however when I attempt to connect to any service on the local lan the following message is displayed in the log can you help:
    Teardown UDP connection 192.168.110.200 53785 192.168.110.21 53 outside:192.168.110.200/53785(LOCAL\username) to inside 192.168.110/53
    See the attached file for a sanitised version of the config.

    This is a sanitised version of the crypto dump, I have changed the user and IP addresses
    ASA5505MAN# debug crypto ikev1 7
    ASA5505MAN# debug crypto ipsec 7
    ASA5505MAN# Jul 24 15:49:03 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=fbc167de) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
    Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
    Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
    Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb72)
    Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb72)
    Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
    Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
    Jul 24 15:49:03 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=515fbf7e) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
    Jul 24 15:49:18 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=2fe7cf10) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
    Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
    Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
    Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb73)
    Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb73)
    Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
    Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
    Jul 24 15:49:18 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=e450c971) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
    Jul 24 15:49:28 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=e6c212e7) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
    Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
    Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
    Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb74)
    Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb74)
    Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
    Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
    Jul 24 15:49:28 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=af5953c7) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
    This is the isakmp dump
    ASA5505MAN# show crypto isakmp
    IKEv1 SAs:
       Active SA: 2
        Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
    Total IKE SA: 2
    1   IKE Peer: x.x.x.x
        Type    : L2L             Role    : initiator
        Rekey   : no              State   : MM_ACTIVE
    2   IKE Peer: x.x.x.x
        Type    : user            Role    : responder
        Rekey   : no              State   : AM_ACTIVE
    There are no IKEv2 SAs
    Global IKEv1 Statistics
      Active Tunnels:              1
      Previous Tunnels:           40
      In Octets:              322076
      In Packets:               2060
      In Drop Packets:            84
      In Notifys:               1072
      In P2 Exchanges:            35
      In P2 Exchange Invalids:     0
      In P2 Exchange Rejects:      0
      In P2 Sa Delete Requests:   24
      Out Octets:             591896
      Out Packets:              3481
      Out Drop Packets:            0
      Out Notifys:              2101
      Out P2 Exchanges:          275
      Out P2 Exchange Invalids:    0
      Out P2 Exchange Rejects:     0
      Out P2 Sa Delete Requests: 284
      Initiator Tunnels:         231
      Initiator Fails:           221
      Responder Fails:            76
      System Capacity Fails:       0
      Auth Fails:                 54
      Decrypt Fails:               0
      Hash Valid Fails:            0
      No Sa Fails:                30
    Global IKEv2 Statistics
      Active Tunnels:                          0
      Previous Tunnels:                        0
      In Octets:                               0
      In Packets:                              0
      In Drop Packets:                         0
      In Drop Fragments:                       0
      In Notifys:                              0
      In P2 Exchange:                          0
      In P2 Exchange Invalids:                 0
      In P2 Exchange Rejects:                  0
      In IPSEC Delete:                         0
      In IKE Delete:                           0
      Out Octets:                              0
      Out Packets:                             0
      Out Drop Packets:                        0
      Out Drop Fragments:                      0
      Out Notifys:                             0
      Out P2 Exchange:                         0
      Out P2 Exchange Invalids:                0
      Out P2 Exchange Rejects:                 0
      Out IPSEC Delete:                        0
      Out IKE Delete:                          0
      SAs Locally Initiated:                   0
      SAs Locally Initiated Failed:            0
      SAs Remotely Initiated:                  0
      SAs Remotely Initiated Failed:           0
      System Capacity Failures:                0
      Authentication Failures:                 0
      Decrypt Failures:                        0
      Hash Failures:                           0
      Invalid SPI:                             0
      In Configs:                              0
      Out Configs:                             0
      In Configs Rejects:                      0
      Out Configs Rejects:                     0
      Previous Tunnels:                        0
      Previous Tunnels Wraps:                  0
      In DPD Messages:                         0
      Out DPD Messages:                        0
      Out NAT Keepalives:                      0
      IKE Rekey Locally Initiated:             0
      IKE Rekey Remotely Initiated:            0
      CHILD Rekey Locally Initiated:           0
      CHILD Rekey Remotely Initiated:          0
    IKEV2 Call Admission Statistics
      Max Active SAs:                   No Limit
      Max In-Negotiation SAs:                 12
      Cookie Challenge Threshold:          Never
      Active SAs:                              0
      In-Negotiation SAs:                      0
      Incoming Requests:                       0
      Incoming Requests Accepted:              0
      Incoming Requests Rejected:              0
      Outgoing Requests:                       0
      Outgoing Requests Accepted:              0
      Outgoing Requests Rejected:              0
      Rejected Requests:                       0
      Rejected Over Max SA limit:              0
      Rejected Low Resources:                  0
      Rejected Reboot In Progress:             0
      Cookie Challenges:                       0
      Cookie Challenges Passed:                0
      Cookie Challenges Failed:                0
    Global IKEv1 IPSec over TCP Statistics
    Embryonic connections: 0
    Active connections: 0
    Previous connections: 0
    Inbound packets: 0
    Inbound dropped packets: 0
    Outbound packets: 0
    Outbound dropped packets: 0
    RST packets: 0
    Recevied ACK heart-beat packets: 0
    Bad headers: 0
    Bad trailers: 0
    Timer failures: 0
    Checksum errors: 0
    Internal errors: 0
    ASA5505MAN#
    and this is the ipsec dump
    ASA5505MAN# show crypto ipsec sa
    interface: outside
        Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: x.x.x.x
          local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
          remote ident (addr/mask/prot/port): (192.168.110.200/255.255.255.255/0/0)
          current_peer: x.x.x.x, username: username
          dynamic allocated peer ip: 192.168.110.200
          #pkts encaps: 778, #pkts encrypt: 778, #pkts digest: 778
          #pkts decaps: 1959, #pkts decrypt: 1959, #pkts verify: 1959
          #pkts compressed: 0, #pkts decompressed: 0
          #pkts not compressed: 778, #pkts comp failed: 0, #pkts decomp failed: 0
          #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
          #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
          #TFC rcvd: 0, #TFC sent: 0
          #Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
          #send errors: 0, #recv errors: 0
          local crypto endpt.: x.x.x.x/4500, remote crypto endpt.: x.x.x.x/54599
          path mtu 1500, ipsec overhead 82(52), media mtu 1500
          PMTU time remaining (sec): 0, DF policy: copy-df
          ICMP error validation: disabled, TFC packets: disabled
          current outbound spi: 532B60D0
          current inbound spi : 472C8AE7
        inbound esp sas:
          spi: 0x472C8AE7 (1194101479)
             transform: esp-aes esp-sha-hmac no compression
             in use settings ={RA, Tunnel,  NAT-T-Encaps, IKEv1, }
             slot: 0, conn_id: 241664, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
             sa timing: remaining key lifetime (sec): 26551
             IV size: 16 bytes
             replay detection support: Y
             Anti replay bitmap:
              0xFFFFFFFF 0xFFFFFFFF
        outbound esp sas:
          spi: 0x532B60D0 (1395351760)
             transform: esp-aes esp-sha-hmac no compression
             in use settings ={RA, Tunnel,  NAT-T-Encaps, IKEv1, }
             slot: 0, conn_id: 241664, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
             sa timing: remaining key lifetime (sec): 26551
             IV size: 16 bytes
             replay detection support: Y
             Anti replay bitmap:
              0x00000000 0x00000001
        Crypto map tag: outside_map0, seq num: 1, local addr: x.x.x.x
          access-list outside_cryptomap_1 extended permit ip 192.168.110.0 255.255.255.0 192.168.0.0 255.255.0.0
          local ident (addr/mask/prot/port): (192.168.110.0/255.255.255.0/0/0)
          remote ident (addr/mask/prot/port): (192.168.0.0/255.255.0.0/0/0)
          current_peer: x.x.x.x
          #pkts encaps: 39333117, #pkts encrypt: 39333117, #pkts digest: 39333117
          #pkts decaps: 24914965, #pkts decrypt: 24914965, #pkts verify: 24914965
          #pkts compressed: 0, #pkts decompressed: 0
          #pkts not compressed: 39333117, #pkts comp failed: 0, #pkts decomp failed: 0
          #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
          #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
          #TFC rcvd: 0, #TFC sent: 0
          #Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
          #send errors: 0, #recv errors: 0
          local crypto endpt.: x.x.x.x/0, remote crypto endpt.: x.x.x.x/0
          path mtu 1500, ipsec overhead 58(36), media mtu 1500
          PMTU time remaining (sec): 0, DF policy: copy-df
          ICMP error validation: disabled, TFC packets: disabled
          current outbound spi: F6943017
          current inbound spi : E6CDF924
        inbound esp sas:
          spi: 0xE6CDF924 (3872258340)
             transform: esp-3des esp-sha-hmac no compression
             in use settings ={L2L, Tunnel, IKEv1, }
             slot: 0, conn_id: 163840, crypto-map: outside_map0
             sa timing: remaining key lifetime (kB/sec): (3651601/15931)
             IV size: 8 bytes
             replay detection support: Y
             Anti replay bitmap:
              0xFFFFFFFF 0xFFFFFFFF
        outbound esp sas:
          spi: 0xF6943017 (4136906775)
             transform: esp-3des esp-sha-hmac no compression
             in use settings ={L2L, Tunnel, IKEv1, }
             slot: 0, conn_id: 163840, crypto-map: outside_map0
             sa timing: remaining key lifetime (kB/sec): (3561355/15931)
             IV size: 8 bytes
             replay detection support: Y
             Anti replay bitmap:
              0x00000000 0x00000001
    ASA5505MAN#

  • ASA 5505 VPN with backup route

    We are looking to set up a site-to-site VPN with a backup over a T1. We have a remote site with a  1841 router. This router has a PTP T1 back to a secondary location with a 2811. Due to location, the only option we had to get additional bandwidth was to have a cable modem installed. We want to set a site-to-site up to our primary location, with a backup route over the T1 in the event the cable modem goes down. We have an ASA 5505 at the remote location, and an ASA 5540 at the primary. In addition, we want to split the traffic across the two connections. Since the wireless controllers are anchored back to the secondary location, we want to send that traffic over the PTP T1 and the rest of the traffic over the VPN. We also need to have a backup route for the wireless traffic to send across the VPN in the event the T1 goes down.

    Go to this link and scroll down to  Site to Site VPN (L2L) with IOS  and Site to Site VPN (L2L) with ASA, you can use the links example depicting your scenario requirements, where one end is dynamic and other static for Ipsec L2L  IOS-to-ASA or ASA-to-IOS.
    The best solution obiosly is having  static IP addressing, make that clear with your client  , but  these exmaples are very good solution for your problem.
    Keep in mind that the DHCP dynamic side will  always be the initiator to  bring up the tunnel , not the static side.
    http://www.cisco.com/en/US/products/ps6120/prod_configuration_examples_list.html
    Regards

  • ASA 5505 VPN HELP!!!

    I have two ASA 5505's.  One is currently setup as my firewall connected to the Cox Cable modem and wireless AP.  I have another ASA that I would like to use, I have an idea that I could set that one up as a VPN unit, but not sure how I could do that.  If that is not an option, can you provide the command line instructions on how to setup the VPN via the console cable.  I am kinda new and I am slowing trying to become more knowledgeable about this.  Any help would be greatly appreciated.
    Thanks,
    Jon
    My current Config:
    ASA Version 8.2(3)wn coldstart' comm
    !d
    hostname Wood-ASA1-if
    %ASA-5-111008:
    domain-name lv.cox.net the 'inspect ip-optio
    enable password 8Ry2YjIyt7RRXU24 encrypted8cb69fe 20cfb60adisk0:/asa823.bin      
    passwd 2KFQnbNIdI.2KYOU encrypteded the 'service-policy global_pol
    namesobal'
    !a
    interface Ethernet0/0in        ^         
    switchport access vlan 2%ASA-5-
    command.ser 'Con
    !S
    interface Ethernet0/1ig' executed the 'pro
    !t
    interface Ethernet0/2mand.tics access-lirv
    interface Ethernet0/3 securi
    rd DfltAccess
    !l
    interface Etherne              
    interface Vlan1ecuted the 'pro
    nameif inside' command.omma
    security-level 100
    %ASA-5-111008: Use
    ip address 192.168.1.1 255.255.255.01008: User 'Config' executed the 'no
    !t
    interface Vlan2 the '
    %ASA-5-1
    nameif outsidefig' executed t
    security-level 0-5-111008: User '
    ip address dhcp setrouteination address http http
    boot system disk0:/asa823-k8.bing' executed the 'class-map inspe
    boot config disk0:/asa823.binom/its/service/oddce/services
    ftp mode passivemand. User 'Conf
    dns server-group DefaultDNS User 'Config' execut
    %ASA-
    domain-name lv.cox.netexecuted the 'destinati
    object-group icmp-type ICMP-INBOUNDation linkup linkdown coldstart' co
    description Permit necessary inbound ICMP trafficand.'policy-map type
    %ASA-5-111008: User 'Config'
    icmp-object echo-replyon transport-method htt
    icmp-object unreachable
    s_map' command.t
    icmp-object t            
    %ASA-
    logging buffered warningsecuted the 'subscribe-to-
    logging asdm notificationsxecuted t
    %ASA-5-111008: U
    mtu inside 1500cuted the 'poli
    mtu outside 1500ct
    riodic month
    icmp unreachable rate-limit 1 burst-size 1-111008: User 'Config' executed the 'subsc
    asdm image disk0:/asdm-625.bino5-111008: User 'Config' execu
    no asdm history enablemmand.outside' command
    arp timeout 14400monthly' command.
    nat-control
    %ASA-5-111
    global (outside) 1 interfacenfig' executed the 'subscrib
    nat (inside) 1 0.0.0.0 0.0.0.0andasa# threat-detec
    d.n
    %ASA
    access-group INBOUND in interface outside08: Us
    riodic daily' command.e          
    timeout xlate 3:             
    aaa authentication ssh console LOCALe Ethernet0/5, changed state to admi
    http server enableas
    %ASA-5-111008:
    http 192.168.1.0 255.255.255.0 inside' executed the
    %ASA-4-411003: Interfa
    no snmp-server locationstate to administra con
    no snmp-server contact                     
    telnet timeout 5# nat-contr
    %ASA
    ssh 0.0.0.0 0.0.0.0 insideec
    %ASA-4-411001: Line pro
    ssh 0.0.0.0 0.0.0.0 outside/3, changed state to upomma
    ssh timeout 5SA-5-111
    %ASA
    console timeout 0onfig' executed t
    dhcpd dns 8.8.8.8 8.8.4.4ne protocol on Interface
    dhcpd auto_config outside to ups_map' com
    %ASA-5-1
    !0
    dhcpd address 192.168.1.2-192.168.1.33 insideommand
    enableR: % I
    Password:SA-5-1110
    Wood-A
    dhcpd dns 8.8.8.8 8.8.4.4 interface inside: Uname: enable_15 From: 1 To:pect netbios
    dhcpd enable insidescoas
    %ASA-5-111008
    !U
    threat-detection basic-threat%ASA-5-111008: User 'enable_1
    threat-detection statistics acce
    .0.0.0 0.0.0.        
    parametersprompt host
      message-length maximum client auto1008: User 'enable_15' executed the
      message-length maximum 512A-5-111008: User 'Config' ex
    policy-map type inspect dns prsent_dns_map 0/0' command. executed the 'inspe
    no shut
    parametersA-5
    Wood-AS
      message-length maximum 512 Interface Ethernet0/0, chan
    policy-map global_policyg' executed the 'inspect
    class inspection_defaultA-5-111008: User 'Con
    ini
      inspect dns preset_dns_map
    %ASA-5-111008: User 'enable
      inspect ftpthe 'no shutd
      inspect h323 h225111008: User 'Confi
      inspect h323 rasstination address
      inspect rsh1001: Line pr
      inspect ip-options
    service-policy global_policy global
    prompt hostname context
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DD
    CEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:c3a35118ab34143a5e73e414ead343c1

    for sure you can do this with the ASA , see the following configuration example :
    http://www.cisco.com/en/US/partner/products/ps6120/products_configuration_example09186a0080950890.shtml
    cheers.

Maybe you are looking for

  • FLA to HTML5 invalid asset in InDesign Folio Builder?

    Hi, So basically im trying to create a magazine getting ready to publish on an iPad. I know animations are not supported on Ipad devices/software, So I looked at Terry Whites tutorial on basically how to still add animation to a publication. I follow

  • IPC requirement does not effect sales order

    Hi, I wrote a pricing requirement  in java extending RequirementAdapter. I uploaded it to the CRM system. When the requirement  is called, it writes messages to the VMC log and i can see the result of the requirement  : "true" or "false" . The proble

  • "Previous Version" analogue rollback software

    Hello there, I was wondering if anyone here has experience with tools that work in the same way "Previous Versions" work in "M$ Window$". This tool gives the user the possibilitie to "roll back" changes or recover deleted documents from a file share.

  • Binding Parameters of EXTSRV-PROCESS

    Hi, We are using adobe forms for PCR approval using the Business object method EXTSRV-PROCESS. This business object when entered in the task requires the follwing parameters as binding elements, <b>Import parameters</b> MODE REQUEST_NO DESCRIPTION IF

  • Failure to generate waveform / import audio from a video

    When I try to load an avi, which used to work before, the video gets loaded and I can watch it however there is absolutely no audio imported. I have tried opening videos that I had previously used and those don't have sound either. I also updated, di