ASA 5520 NAT 8.4

Hello All,
Im having an issue setting up Access through our firewall for external usage. Im not sure if its even possible.
So....
We have 1 external IP, say 80.80.80.80.
We have 3 internal Servers (10.0.0.1, 10.0.0.2, 10.0.0.3), 2 running web apps on ports 443 and one on 445.
We have 2 external locations (source IPs) London (50.50.50.50), Reading (60.60.60.60).
I want to be able to match the source address either london and reading and direct to the correct internal server, so 10.0.0.1 is for london and 10.0.0.2 is for reading both using the same IP and ports?
Is this possible, can the NAT rulles match on source IP?
Cheers
Craig

Hi,
Below is some configurations I tested when a similiar question was asked on these forums.
In the below configurations I attempted to test a situation where the where the source address from the public network would define which NAT would be used and therefore to which LAN host the connection woulld be forwarded to. Also the situation was limited to using only the single IP address configured on the ASA "outside/WAN" interface.
To my understanding this solution is hardly ideal when considering the firewall operation. I think the firewall actually warns about the overlaps and actually shows overlapping translations on the firewall.
Still I was able to test this from 2 different external hosts at the same time on my home network and it was working. I havent tested this in active use so I cant say for certain what kind of problems you might run into or if there is perhaps problems with the operation when multiple hosts are connecting and attempting all the different connections the NAT configurations are used for.
So below are the example configurations and later the clarifications on what they are supposed to do. This should be easy to apply to your specific setup
EDIT: The naming and parameters referring to destination and source might be a bit confusing. Naturally you can use the object names that make the most sense to you.
object network SOURCE1
host 1.2.3.4
object network SOURCE2
host 5.6.7.8
object network SERVER1
host 10.10.10.10
object network SERVER2
host 10.10.10.20
object service VNC
service tcp source eq 5900
nat (LAN,WAN) source static SERVER1 interface destination static SOURCE1 SOURCE1 service VNC VNC
nat (LAN,WAN) source static SERVER2 interface destination static SOURCE2 SOURCE2 service VNC VNC
access-list WAN-IN extended permit tcp object SOURCE1 object SERVER1 eq 5900
access-list WAN-IN extended permit tcp object SOURCE2 object SERVER2 eq 5900
access-group WAN-IN in interface WAN
Where
SOURCE1 / SOURCE2 = contains the users public source IP address
SERVER1 / SERVER2 = contains the servers local IP address to which SOURCE1/SOURCE2 is connecting to
VNC = contains the service that is to be forwarded
LAN = is my "inside" interface
WAN = is my "outside" interface
WAN-IN = is my "outside" inbound ACL
The above NAT commands basically state that
Translation will happen between LAN and WAN interface
The SERVER1 / SERVER2 will be translated to the WAN interface IP address ("interface" parameter) when the other end of the connection is SOURCE1 / SOURCE2 and the service used is TCP/5900 (both mapped and real service is TCP/5900)
Hopefully the information has been helpfull
- Jouni

Similar Messages

VPN clients not able to ping Remote PCs & Servers : ASA 5520

VPN is connected successfully. But not able to ping any remote ip or fqdn from client pc. But able to ping ASA 5520 firewalls inside interface. Also some clients able to access, some clients not able to access. I new to these firewalls. I tried most of ways from internet, please any one can help asap.
Remote ip section : 192.168.1.0/24
VPN IP Pool : 192.168.5.0/24
Running Config :
ip address 192.168.1.2 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
shutdown
no nameif
no security-level
no ip address
management-only
passwd z40TgSyhcLKQc3n1 encrypted
boot system disk0:/asa722-k8.bin
ftp mode passive
clock timezone GST 4
dns domain-lookup outside
dns domain-lookup inside
dns server-group DefaultDNS
name-server 213.42.20.20
domain-name default.domain.invalid
access-list outtoin extended permit tcp any host 83.111.113.114 eq 3389
access-list outtoin extended permit tcp any host 83.111.113.113 eq https
access-list outtoin extended permit tcp any host 83.111.113.114 eq smtp
access-list outtoin extended permit tcp any host 83.111.113.114 eq https
access-list outtoin extended permit tcp any host 83.111.113.114 eq www
access-list outtoin extended permit tcp any host 83.111.113.115 eq https
access-list outtoin extended permit tcp any host 94.56.148.98 eq 3389
access-list outtoin extended permit tcp any host 83.111.113.117 eq ssh
access-list fualavpn_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip 192.168.5.0 255.255.255.0
92.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 1
2.168.5.0 255.255.255.0
access-list inet_in extended permit icmp any any time-exceeded
access-list inet_in extended permit icmp any any unreachable
access-list inet_in extended permit icmp any any echo-reply
access-list inet_in extended permit icmp any any echo
pager lines 24
logging enable
logging asdm informational
logging from-address [email protected]
logging recipient-address [email protected] level errors
logging recipient-address [email protected] level emergencies
logging recipient-address [email protected] level errors
mtu outside 1500
mtu inside 1500
ip local pool fualapool 192.168.5.10-192.168.5.50 mask 255.255.255.0
ip local pool VPNPool 192.168.5.51-192.168.5.150 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-522.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound outside
nat (inside) 1 192.168.1.0 255.255.255.0
static (inside,outside) 94.56.148.98 192.168.1.11 netmask 255.255.255.255
static (inside,outside) 83.111.113.114 192.168.1.111 netmask 255.255.255.255
access-group inet_in in interface outside
route outside 0.0.0.0 0.0.0.0 83.111.113.116 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
group-policy DfltGrpPolicy attributes
banner none
wins-server none
dns-server none
dhcp-network-scope none
vpn-access-hours none
vpn-simultaneous-logins 10
vpn-idle-timeout 30
vpn-session-timeout none
vpn-filter none
vpn-tunnel-protocol IPSec l2tp-ipsec webvpn
password-storage disable
ip-comp disable
re-xauth disable
group-lock none
pfs disable
ipsec-udp disable
ipsec-udp-port 10000
split-tunnel-policy tunnelall
split-tunnel-network-list none
default-domain none
split-dns none
intercept-dhcp 255.255.255.255 disable
secure-unit-authentication disable
user-authentication disable
user-authentication-idle-timeout 30
ip-phone-bypass disable
leap-bypass disable
nem disable
backup-servers keep-client-config
msie-proxy server none
msie-proxy method no-modify
msie-proxy except-list none
msie-proxy local-bypass disable
nac disable
nac-sq-period 300
nac-reval-period 36000
nac-default-acl none
address-pools none
client-firewall none
client-access-rule none
webvpn
functions url-entry
html-content-filter none
homepage none
keep-alive-ignore 4
http-comp gzip
filter none
url-list none
customization value DfltCustomization
port-forward none
port-forward-name value Application Access
sso-server none
deny-message value Login was successful, but because certain criteria have no
been met or due to some specific group policy, you do not have permission to u
e any of the VPN features. Contact your IT administrator for more information
svc none
svc keep-installer installed
svc keepalive none
svc rekey time none
svc rekey method none
svc dpd-interval client none
svc dpd-interval gateway none
svc compression deflate
group-policy fualavpn internal
group-policy fualavpn attributes
dns-server value 192.168.1.111 192.168.1.100
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value fualavpn_splitTunnelAcl
username test password I7ZgrgChfw4FV2AW encrypted privilege 0
username Mohamed password Vqmmt8cR/.Qu7LhU encrypted privilege 0
username Moghazi password GMr7xgdqmGEQ2SVR encrypted privilege 0
username Moghazi attributes
password-storage enable
username fualauaq password E6CgvoOpTKphiM2U encrypted privilege 0
username fualauaq attributes
password-storage enable
username fuala password IFtijSYb7LAOV/IW encrypted privilege 15
username Basher password Djf15nXIJXmayfjY encrypted privilege 0
username Basher attributes
password-storage enable
username fualafac password VGC/7cKXW1A6eyXS encrypted privilege 0
username fualafac attributes
password-storage enable
username fualaab password ONTH8opuP4RKgRXD encrypted privilege 0
username fualaab attributes
password-storage enable
username fualaadh2 password mNEgLxzPBeF4SyDb encrypted privilege 0
username fualaadh2 attributes
password-storage enable
username fualaain2 password LSKk6slwsVn4pxqr encrypted privilege 0
username fualaain2 attributes
password-storage enable
username fualafj2 password lE4Wu7.5s7VXwCqv encrypted privilege 0
username fualafj2 attributes
password-storage enable
username fualakf2 password 38oMUuwKyShs4Iid encrypted privilege 0
username fualakf2 attributes
password-storage enable
username fualaklb password .3AMGUZ1NWU1zzIp encrypted privilege 0
username fualaklb attributes
password-storage enable
username fualastr password RDXSdBgMaJxNLnaH encrypted privilege 0
username fualastr attributes
password-storage enable
username fualauaq2 password HnjodvZocYhDKrED encrypted privilege 0
username fualauaq2 attributes
password-storage enable
username fualastore password wWDVHfUu9pdM9jGj encrypted privilege 0
username fualastore attributes
password-storage enable
username fualadhd password GK8k1MkMlIDluqF4 encrypted privilege 0
username fualadhd attributes
password-storage enable
username fualaabi password eYL0j16kscNhhci4 encrypted privilege 0
username fualaabi attributes
password-storage enable
username fualaadh password GTs/9BVCAU0TRUQE encrypted privilege 0
username fualaadh attributes
password-storage enable
username fualajuh password b9QGJ1GHhR88reM1 encrypted privilege 0
username fualajuh attributes
password-storage enable
username fualadah password JwVlqQNIellNgxnZ encrypted privilege 0
username fualadah attributes
password-storage enable
username fualarak password UE41e9hpvcMeChqx encrypted privilege 0
username fualarak attributes
password-storage enable
username fualasnk password ZwZ7fVglexrCWFUH encrypted privilege 0
username fualasnk attributes
password-storage enable
username rais password HrvvrIw5tEuam/M8 encrypted privilege 0
username rais attributes
password-storage enable
username fualafuj password yY2jRMPqmNGS.3zb encrypted privilege 0
username fualafuj attributes
password-storage enable
username fualamaz password U1YUfQzFYrsatEzC encrypted privilege 0
username fualamaz attributes
password-storage enable
username fualashj password gN4AXk/oGBTEkelQ encrypted privilege 0
username fualashj attributes
password-storage enable
username fualabdz password tg.pB7RXJx2CWKWi encrypted privilege 0
username fualabdz attributes
password-storage enable
username fualamam password uwLjc0cV7LENI17Y encrypted privilege 0
username fualamam attributes
password-storage enable
username fualaajm password u3yLk0Pz0U1n.Q0c encrypted privilege 0
username fualaajm attributes
password-storage enable
username fualagrm password mUt3A60gLJ8N5HVr encrypted privilege 0
username fualagrm attributes
password-storage enable
username fualakfn password ceTa6jmvnzOFNSgF encrypted privilege 0
username fualakfn attributes
password-storage enable
username Fualaain password Yyhr.dlc6/J7WvF0 encrypted privilege 0
username Fualaain attributes
password-storage enable
username fualaban password RCJKLGTrh7VM2EBW encrypted privilege 0
username John password D9xGV1o/ONPM9YNW encrypted privilege 15
username John attributes
password-storage disable
username wrkshopuaq password cFKpS5e6Whp0A7TZ encrypted privilege 0
username wrkshopuaq attributes
password-storage enable
username Talha password 3VoAABwXxVonLmWi encrypted privilege 0
username Houssam password Cj/uHUqsj36xUv/R encrypted privilege 0
username Faraj password w2qYfE3DkYvS/oPq encrypted privilege 0
username Faraj attributes
password-storage enable
username gowth password HQhALLeiQXuIzptCnTv1rA== nt-encrypted privilege 15
username Hameed password 0Kr0N1VRmLuWdoDE encrypted privilege 0
username Hameed attributes
password-storage enable
username Hassan password Uy4ASuiNyEd70LCw encrypted privilege 0
username cisco password IPVBkPI1GLlHurPD encrypted privilege 15
username Karim password 5iOtm58EKMyvruZA encrypted privilege 0
username Shakir password BESX2bAvlbqbDha/ encrypted privilege 0
username Riad password iB.miiOF7qMESlCL encrypted privilege 0
username Azeem password 0zAqiCG8dmLyRQ8f encrypted privilege 15
username Azeem attributes
password-storage disable
username Osama password xu66er.7duIVaP79 encrypted privilege 0
username Osama attributes
password-storage enable
username Mahmoud password bonjr0B19aOQSpud encrypted privilege 0
username alpha password x8WO0aiHL3pVFy2E encrypted privilege 15
username Wissam password SctmeK/qKVNLh/Vv encrypted privilege 0
username Wissam attributes
password-storage enable
username Nabil password m4fMvkTgVwK/O3Ms encrypted privilege 0
aaa authentication telnet console LOCAL
aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
http server enable
http 0.0.0.0 0.0.0.0 outside
http 192.168.1.4 255.255.255.255 inside
http 192.168.1.100 255.255.255.255 inside
http 192.168.1.111 255.255.255.255 inside
http 192.168.1.200 255.255.255.255 inside
http 83.111.113.117 255.255.255.255 outside
http 192.168.1.17 255.255.255.255 inside
http 192.168.1.16 255.255.255.255 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
tunnel-group fualavpn type ipsec-ra
tunnel-group fualavpn type ipsec-ra
tunnel-group fualavpn general-attributes
address-pool fualapool
address-pool VPNPool
default-group-policy fualavpn
tunnel-group fualavpn ipsec-attributes
pre-shared-key *
tunnel-group fualavpn ppp-attributes
authentication pap
authentication ms-chap-v2
authentication eap-proxy
telnet 0.0.0.0 0.0.0.0 outside
telnet 0.0.0.0 0.0.0.0 inside
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 192.168.1.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
management-access inside
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns migrated_dns_map_1
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns migrated_dns_map_1
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
inspect icmp error
service-policy global_policy global
prompt hostname context
Cryptochecksum:38e41e83465d37f69542355df734db35
: end

Hi,
What about translating the traffic on the local ASA (Active unit) for traffic received from the VPN tunnel to the internal interface IP address? You can try something like nat (outside,inside) source dynamic obj-VpnRemoteTraffic interface destination static StandbyIP StandbyIP
Regards,

ASA 5520 Upgrade From 8.2 to 9.1

To All Pro's Out There,
I have 2 x ASA 5520 in Active/Standby state (Routed, Single context) running 8.2(3) image. They are working great and everybody is happy. Now it's time for us to upgrade to the latest and greatest version: 9.1 and as you know there are some architectural changes Cisco made to NAT statements and Access Lists. As one can tell, we have a monster environment in terms of NAT statements and access list that are currently configured on the appliances.
In order to make the upgrade process "less" painful, I was able to find a loaner ASA 5520 device so I can practice the upgrade process offline and if needed, I use it in production (in conjunction with existing Primary and Secondary devices) should it be helpful. I currently don't have any plans on how to move forward with these 3 devices and put together an smooth upgrade. I am asking advice from experts that perhaps have done this in the past and know some Do's and Don’ts and can provide me some options toward getting best result: Minimum downtime and Smooth upgrade.
I appreciate all the help in advance.

Hi,
My personal approach from the start has been to learn the new NAT configuration format on the ASA CLI and manually convert the configurations for the new ASA software. I am under the impression that the automatic conversion that the ASA does by rebooting straight into a new software level causes quite a lot of configurations and they arent really optimal.
In your case it seems that you have a pretty much better situation than most people that dont have the chance to use a test device to test out the setup before actually putting it in production.
What you can basically do is
Insert the 8.2 configuration to the test ASA and boot it straight to the higher software levels and see what the conversion has done to the ASA configurations.
You can use "packet-tracer" command to test if correct NAT rules are still hit after the conversion
So far I have been lucky in the sense that most of the upgrades I have done have involved new hardware which has basically let me configure everything ready and just switch devices for the customer. So far everything has went really well and there has been only a 1-2 mistakes in NAT configurations because of misstyping some IP address or interface name which basically resulted from a lot of copy/paste when building the configurations. And these couple of mistakes have been from around 150 firewall migrations (of which most from FWSM Security Context to a ASA Security Context)
If you have time to put into this then I would suggest you try to learn the new NAT format and write your NAT configurations yourself. Converting the existing configurations should essentially give you the tools to then maintain that firewall configuration easily in the future and apply that knowledge elsewhere.
If you want to read a bit about the new NAT configuration format then I would suggest having a look at the NAT 8.3+ document I made:
https://supportforums.cisco.com/docs/DOC-31116
My personal approach when starting to convert NAT configurations for the upgrade is
Collect all NAT configurations from the current ASA including any ACLs associated with the Policy type NATs and NAT0 configurations
Divide NAT configurations based on type
Dynamic NAT/PAT
Static NAT
Static PAT
NAT0
All Policy Dynamic/Static NAT/PAT
Learn the basic configuration format for each type of NAT configuration
Start by converting the easiest NAT configurations
Dynamic NAT/PAT
Static NAT/PAT
Next convert the NAT0 configurations
And finally go through the Policy NAT/PAT configurations
Finally go through the interface ACLs and change them to use the real IP address as the destination in all cases since the NAT IP address is not used anymore. In most common screnarios this basically usually only involves modifying the "outside" interfaces ACL but depending if the customer has some other links to external resourses then its highly likely that same type of ACL changes are required on those interfaces also.
The most important thing is to understand how the NAT is currently working and then configure the new NAT configuration to match that. Again, the "packet-tracer" command is a great tool to confirm that everything is working as expected.
One very important thing to notice also is that you might have a very large number of Identity NAT configurations between your local networks interfaces of the ASA.
For example
static (inside,dmz) 10.10.10.0 10.10.10.0 netmask 255.255.255.0
In the new software you can pretty much leave all of these out. If you dont need to perform NAT between your local interfaces then you simply leave out all NAT configurations.
Naturally you can also use these forums to ask help with NAT configuration conversions. Even though its a very common topic, I dont personally mind helping out with those.
So to summarize
Try out the ASAs automatic configuration conversion when simply booting to new software levels on the test ASA you have
Learn the new NAT configuration format
Ask for help here on CSC about NAT configuration formats and help with converting old to new configurations.
Personally if I was looking at a samekind of upgrade (which I will probably be looking at again soon) I would personally do the following
Convert the configurations manually
Lab/test the configurations on an test ASA
During Failover pairs upgrade I would remove the Standby device from network, erase its configurations, reboot it to new software, insert manually written configurations.
Put the upgraded ASA to the device rack and have cables ready connected to the customer devices if possible (or use existing ones)
Disconnect currently active ASA running 8.2 and connect the new ASA to the network while clearing ARP on the connected routers to avoid any problems with traffic forwarding.
Test connectivity and monitor ASAs connection and xlate tables to confirm everything is working
Will add more later if anything comes to mind as its getting quite late here
Hope this helps
- Jouni

ASA vpn nat question

i have an ASA 5520 ver 8.4 with the following config
WAN
207.211.25.34
Production
10.11.12.1 255.255.255.0
Mgmt
10.11.11.1 255.255.255.0
i need to create a peer-2-peer VPN to a remote site ASP16 from both Prod and Mgmt
what would my nat statement look like ?
currently i have the following but can only ping from Mgmt not Prod (ASP17 is an network object group that contain the Prod and Mgmt subnets )
nat (Production,WAN) source static ASP17_VPN ASP17_VPN destination static ASP16 ASP16 no-proxy-arp route-lookup
nat (Mgmt,WAN) source static ASP17_VPN ASP17_VPN destination static ASP8_Prod ASP8_Prod

Hello Tejas,
After reading your configuration I can see that the crypto-maps are applyed to the outside interface, and the Access-list for the interesting traffic has both networks (Managment and production) so you should be able to access the other network from this site.
Can you do the following packet tracers to see the features the ICMP packet is hitting when the Request is sent.
I will need the output of the following commands:
1- Packet-tracer input Mgmt icmp 10.11.34.15 8 0 10.30.6.15
2-Packet-tracer input Production icmp 10.11.35.15 8 0 10.30.6.15
Please rate helpful posts,
Julio!!

Multiple Public IP's on ASA 5520

Hi,
I have ASA 5520 with Ver 8.2.
Outside interface is directly connected to ISP's router(TelePacific) and is assigned one of public IP:198.24.210.226.
There are two servers inside the network with the private IP's:192.168.1.20 for DB Server, and 192.168.1.91 for Web Server.
I did Static NAT 198.24.210.226 to 192.168.1.20 and 198.24.210.227 to 192.168.1.91.
When I access DB Server(198.24.210.226) it's working OK but when I access Web Server(198.24.210.227) there is no response at all.
I checked the inside traffic, it even did not get into the firewall.
Is this the problem with ISP's router? How can we route all of our public IP's to the outside interface(198.24.210.226)?
interface GigabitEthernet0/1
nameif inside
ip address 192.168.1.1 255.255.255.0
security-level 100
no shutdown
interface GigabitEthernet0/0
nameif outside
ip address 198.24.210.226 255.255.255.248
security-level 0
no shutdown
route outside 0.0.0.0 0.0.0.0 198.24.210.225
nat (inside) 1 192.168.1.0 255.255.255.0
global (outside) 1 198.24.210.226 255.255.255.255
static (inside,outside) tcp 198.24.210.226 3389 192.168.1.10 3389 netmask 255.255.255.255 dns
static (inside,outside) tcp 198.24.210.226 9070 192.168.1.10 9070 netmask 255.255.255.255 dns
static (inside,outside) tcp 198.24.210.227 3389 192.168.1.20 3389 netmask 255.255.255.255 dns
static (inside,outside) tcp 198.24.210.227 80 192.168.1.20 80 netmask 255.255.255.255 dns
access-list OUTSIDE-IN extended permit tcp any host 198.24.210.226 eq 3389
access-list OUTSIDE-IN extended permit tcp any host 198.24.210.226 eq 9070
access-list OUTSIDE-IN extended permit tcp any host 198.24.210.227 eq 3389
access-list OUTSIDE-IN extended permit tcp any host 198.24.210.227 eq 80
access-group OUTSIDE-IN in interface outside

Also,
You seen to have an /29 public subnet. You should be able to use IP addresses from this subnet to configure NAT on your firewall. I dont think you need any specific configurations to allow the usage of the whole subnet as NAT IP addresses.
You can naturally check the following
show run sysopt
Check that you DONT have the following
sysopt noproxyarp outside
At the moment you are not actually configuring Static NAT but rather Static PAT.
You are only forwarding some ports from certain public IP addresses to the local IP address. If you were doing Static NAT, then you would actually be staticly binding the public IP addresses to the local IP address. So it would apply to any TCP/UDP port and you would only need to use the ACL to allow traffic.
Though in that case you would have to replace the .226 IP address with something else as its the firewall interface IP address and it should not be assigned to be used by a single host on the LAN usually.
If you wanted to staticly assing public IPs to both of these servers you could do
static (inside,outside) 198.24.210.227 192.168.1.91 netmask 255.255.255.255
static (inside,outside) 198.24.210.228 192.168.1.10 netmask 255.255.255.255
access-list OUTSIDE-IN extended permit tcp any host 198.24.210.228 eq 3389
access-list OUTSIDE-IN extended permit tcp any host 198.24.210.228 eq 9070
access-list OUTSIDE-IN extended permit tcp any host 198.24.210.227 eq 3389
access-list OUTSIDE-IN extended permit tcp any host 198.24.210.227 eq 80
- Jouni

ASA 5520 intervlan routing at low speed

I have ASA 5520 and SSM-10 module. During copy between vlans, connected to gigabit port of asa the speed is up to 6,5 Mbyte/sec. Network cards and trunked switch are gigabit. I've temporarily disabled SSM but it didn't help. Here is my config. Also I found out, that putting SSM into bypass mode solves the problem. But I don't send any traffic to IPS...
ASA Version 8.4(2)
hostname ***
domain-name ***
enable password *** encrypted
passwd *** encrypted
multicast-routing
names
dns-guard
interface GigabitEthernet0/0
nameif DMZ
security-level 50
ip address 10.2.5.1 255.255.255.0
interface GigabitEthernet0/1
nameif inside
security-level 100
no ip address
interface GigabitEthernet0/1.100
vlan 100
nameif Devices
security-level 100
ip address 10.2.0.1 255.255.255.0
interface GigabitEthernet0/1.101
vlan 101
nameif Common
security-level 100
ip address 10.2.1.1 255.255.255.0
interface GigabitEthernet0/1.102
vlan 102
nameif Design
security-level 100
ip address 10.2.2.1 255.255.255.0
interface GigabitEthernet0/1.103
vlan 103
nameif Ruhlamat
security-level 90
ip address 10.2.3.1 255.255.255.0
interface GigabitEthernet0/2
no nameif
security-level 100
no ip address
interface GigabitEthernet0/2.10
vlan 10
nameif HOLOGR
security-level 40
ip address 10.1.2.4 255.255.0.0
interface GigabitEthernet0/3
nameif outside
security-level 0
ip address ***
interface Management0/0
nameif management
security-level 100
ip address 172.16.1.1 255.255.255.0
management-only
boot system disk0:/asa842-k8.bin
no ftp mode passive
clock timezone EEST 2
clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 4:00
dns server-group DefaultDNS
domain-name ***
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network WWW
host 10.2.1.6
object network MAIL
host 10.2.5.5
object network TEST
host 10.2.1.85
object-group network DM_INLINE_NETWORK_1
network-object host 10.1.0.88
network-object host 10.1.6.1
network-object host 10.1.6.5
network-object host 10.1.0.57
network-object 10.2.0.0 255.255.255.0
network-object host 10.1.6.4
network-object host 10.1.1.57
object-group service DM_INLINE_TCP_1 tcp
port-object eq 2080
port-object eq pop3
port-object eq smtp
object-group network DM_INLINE_NETWORK_6
network-object host 10.1.4.42
network-object host 10.1.4.234
network-object host 10.1.4.175
network-object host 10.1.4.217
object-group protocol DM_INLINE_PROTOCOL_5
protocol-object udp
protocol-object tcp
object-group network DM_INLINE_NETWORK_3
network-object host 10.2.1.4
network-object host 10.2.1.5
network-object host 10.2.1.6
network-object host 10.2.1.14
network-object host 10.2.1.91
object-group network DM_INLINE_NETWORK_4
network-object host 10.2.1.4
network-object host 10.2.1.5
network-object host 10.2.1.6
object-group service DM_INLINE_TCP_2 tcp
port-object eq pop3
port-object eq smtp
object-group network DM_INLINE_NETWORK_5
network-object host 10.2.1.14
network-object host 10.2.1.39
network-object host 10.2.1.4
network-object host 10.2.1.5
network-object host 10.2.1.6
network-object host 10.2.1.85
network-object host 10.2.1.31
network-object host 10.2.1.32
network-object host 10.2.1.40
network-object host 10.2.1.55
network-object host 10.2.1.35
network-object host 10.2.1.3
network-object host 10.2.1.2
object-group service DM_INLINE_TCP_3 tcp
port-object eq pop3
port-object eq smtp
object-group network DM_INLINE_NETWORK_7
network-object host 10.2.1.4
network-object host 10.2.1.5
object-group network DM_INLINE_NETWORK_9
network-object host 10.2.1.4
network-object host 10.2.1.3
object-group network DM_INLINE_NETWORK_2
network-object host 10.1.1.101
network-object host 10.1.6.1
network-object host 10.1.6.4
network-object host 10.1.6.5
network-object host 10.1.0.57
network-object host 10.1.1.57
object-group network DM_INLINE_NETWORK_10
network-object host 10.2.1.4
network-object host 10.2.1.5
network-object host 10.2.1.3
network-object host 10.2.1.2
object-group service DM_INLINE_TCP_4 tcp
port-object eq pop3
port-object eq smtp
object-group network DM_INLINE_NETWORK_12
network-object host 10.2.0.11
network-object host 10.2.0.14
object-group service DM_INLINE_TCP_5 tcp
port-object eq pop3
port-object eq smtp
object-group network DM_INLINE_NETWORK_13
network-object host 10.2.1.4
network-object host 10.2.1.5
object-group network DM_INLINE_NETWORK_14
network-object host 8.8.4.4
network-object host 8.8.8.8
network-object host 10.1.1.1
object-group network DM_INLINE_NETWORK_15
network-object host 10.2.1.39
network-object host 10.2.1.57
object-group network DM_INLINE_NETWORK_16
network-object host 10.2.1.14
network-object host 10.2.1.6
access-list outside_access_in extended permit tcp any 10.2.5.0 255.255.255.0 eq smtp
access-list outside_access_in extended permit tcp host *** host 10.2.1.85 eq ***
access-list outside_access_in extended permit tcp host *** host 10.2.1.6 eq ***
access-list Common_access_in extended permit icmp any any
access-list Common_access_in extended permit ip host 10.2.1.76 host ***
access-list Common_access_in extended permit ip host 10.2.1.6 any log disable inactive
access-list Common_access_in extended permit tcp host 10.2.1.6 host *** eq ***
access-list Common_access_in extended permit ip object-group DM_INLINE_NETWORK_1 6 host 10.2.5.5
access-list Common_access_in extended permit ip object-group DM_INLINE_NETWORK_3 10.2.2.0 255.255.255.0
access-list Common_access_in extended permit udp object-group DM_INLINE_NETWORK_7 any eq ntp log disable
access-list Common_access_in extended permit object-group DM_INLINE_PROTOCOL_5 object-group DM_INLINE_NETWORK_13 object-group DM_INLINE_NETWORK_14 eq domain
access-list Common_access_in extended permit ip object-group DM_INLINE_NETWORK_5 host 10.2.3.3
access-list Common_access_in extended permit tcp object-group DM_INLINE_NETWORK_15 host 10.1.1.1 object-group DM_INLINE_TCP_3
access-list Common_access_in extended permit ip 10.2.1.0 255.255.255.0 object-group DM_INLINE_NETWORK_1
access-list Common_access_in extended permit tcp 10.2.1.0 255.255.255.0 host 10.2.5.5 object-group DM_INLINE_TCP_1
access-list Design_access_in extended permit tcp 10.2.2.0 255.255.255.0 host 10.2.5.5 object-group DM_INLINE_TCP_2
access-list Design_access_in extended permit ip 10.2.2.0 255.255.255.0 object-group DM_INLINE_NETWORK_4 log disable
access-list HOLOGR_access_in extended permit icmp any any log disable
access-list HOLOGR_access_in extended permit tcp host 10.1.1.1 host 10.2.5.5 object-group DM_INLINE_TCP_4
access-list HOLOGR_access_in extended permit ip object-group DM_INLINE_NETWORK_6 object-group DM_INLINE_NETWORK_9
access-list HOLOGR_access_in extended permit ip object-group DM_INLINE_NETWORK_2 10.2.1.0 255.255.255.0
access-list HOLOGR_access_in extended permit ip host 10.1.4.214 object-group DM_INLINE_NETWORK_12
access-list Ruhlamat_access_in extended permit ip host 10.2.3.3 object-group DM_INLINE_NETWORK_10
access-list Ruhlamat_access_in extended permit tcp host 10.2.3.3 host 10.2.5.5 object-group DM_INLINE_TCP_5
access-list test extended permit tcp any host 10.2.5.1 eq telnet
access-list test extended permit tcp any host 10.2.5.1 eq https
access-list test extended permit tcp host 10.2.5.1 any eq https
access-list test extended permit tcp host 10.2.5.1 any eq telnet
pager lines 24
logging enable
logging timestamp
logging buffer-size 8192
logging buffered critical
logging trap warnings
logging asdm informational
logging from-address ***
logging recipient-address *** level critical
logging host Common 10.2.1.2
logging flash-bufferwrap
logging flash-maximum-allocation 8192
logging permit-hostdown
no logging message 106014
no logging message 313005
no logging message 313001
no logging message 106023
no logging message 305006
no logging message 733101
no logging message 733100
no logging message 304001
logging message 313001 level critical
logging message 106023 level errors
mtu DMZ 1500
mtu inside 1500
mtu Devices 1500
mtu Common 1500
mtu Design 1500
mtu Ruhlamat 1500
mtu HOLOGR 1500
mtu outside 1500
mtu management 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any DMZ
icmp permit any Common
icmp permit any HOLOGR
icmp permit any outside
asdm image disk0:/asdm-645-206.bin
asdm history enable
arp timeout 14400
object network WWW
nat (Common,outside) static interface service tcp *** ***
object network MAIL
nat (DMZ,outside) static interface service tcp smtp smtp
nat (DMZ,outside) after-auto source dynamic any interface
nat (Common,outside) after-auto source dynamic any interface
nat (Devices,outside) after-auto source dynamic any interface
access-group Common_access_in in interface Common
access-group Design_access_in in interface Design
access-group Ruhlamat_access_in in interface Ruhlamat
access-group HOLOGR_access_in in interface HOLOGR
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 *** 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
no user-identity enable
user-identity default-domain LOCAL
http server enable
http 10.2.1.6 255.255.255.255 Common
snmp-server host Common 10.2.1.6 community *****
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
sysopt noproxyarp DMZ
sysopt noproxyarp inside
sysopt noproxyarp Devices
sysopt noproxyarp Common
sysopt noproxyarp Design
sysopt noproxyarp Ruhlamat
sysopt noproxyarp HOLOGR
sysopt noproxyarp outside
sysopt noproxyarp management
service resetoutside
telnet 10.2.1.0 255.255.255.0 Common
telnet timeout 5
ssh timeout 5
console timeout 0
management-access Common
dhcprelay setroute Common
threat-detection basic-threat
threat-detection scanning-threat
no threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 10.2.1.4 source Common prefer
webvpn
smtp-server 10.2.5.5
prompt hostname context
call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DD
CEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:ad02ecbd84a727e4a26699915feca3a5
: end

Hi Philip,
I don't see any features configured that would affect the throughput of the data transfer. Do you see any CRC errors or overruns increasing on the interfaces during the transfer? If not, I would suggest setting up captures on the ingress and egress interfaces of the ASA so you can understand exactly why the connection is slowing down and see if the ASA is inducing the delay:
https://supportforums.cisco.com/docs/DOC-1222
-Mike

ASA 5520 VERSION 8.2 UPGRADE TO 9.0

Hello friends,
I am considering to perform an upgrade of my ASA 5520 with versión 8.2 to 9.0, so I will enjoy the benefits of anyconnect for mobile devices. I clearly understand that I must pay special attention to:
NAT Rules.
RAM Memory: 2 GB.
Adding the part numbers to power on the newest versions of anyconnect and for mobile devices
L-ASA-AC-E-5520= ASA-AC-M-5520=
am I missing any other thing? Flash requirement? Or to pay attention to some other configurations?
Any comment or documentation will be appreciated.
Regards!

You can run the latest AnyConnect client - including mobile clients - with those licenses even on an ASA with the current 8.2 code - 8.2(5) as of now. While it's a bit old and lacking some of the newer features, it's a solid and stable release.
That would save you the trouble of migrating your NAT configuration (and other bits) and upgrading memory.
Since the ASA 5500 series (5510, 5520 etc.) is past End of Sales you have a limited future on those platforms. For instance, ASA 9.1(x) is the last set of code releases that will be available for them. (The current software on the 5500-X is 9.3(1).)

Cisco ASA 5520 (asa 8.2) hairpinning

Hi All,
We have a ASA 5520 (redundant) in our network which we are using for different customers. For every new customer we create a new VLAN and place their servers in this VLAN. On the ASA we create a new subinterface for every customer which is connected to the corresponding VLAN.
Most customers get a private ip-range (e.g. 192.168.x.x/24) on which they should configure their servers. Because most customers don't need to be to access eachothers server all VLAN interfaces have the same security-level of 50. I haven't enable the "same-security-traffic permit inter-interface" option, so traffic between those interfaces is blocked, as expected.
Some customers (e.g. customer A) need public webmail of smtp access to there servers. So we use both NAT and PAT to make that happen.
So, recently we've got a customer (customer B) who placed their webservers behind our ASA. Because we didn't want to use NAT statements all the time, we dediced to configure a public /29 subnet on their VLAN. Because the website on this customer's servers need to be visible for everybody, we've lowered the security-level of this VLAN interface to 40 (instead of 50) and applied some ACL's. So other customers (e.g. customer A) are also able to reach the websites of customer B. So everything is just working fine.
Now, customer A decided that they want to run their website on their own servers as well. So, I created a static PAT for TCP 80. So the website is accessible from the outside world. But.....customer B is not able to reach customer A's website on the translated address. So, I've created a second PAT (using the same public address) but this time to customer B's interface. But still, we're not able to reach customer A's website.
I've also enabled the "same-security-traffic permit intra-interface", but still the website is unreachable to customer B.
Here's a small drawing of the situation:
The ip-addresses are, of course, not real.
Can anybody place help me with this issue?

That's a very cool command that I didn't know about.
I see that the packet is drop at phase 7 (NAT-EXEMPT).
Phase: 7
Type: NAT-EXEMPT
Subtype: rpf-check
Result: DROP
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0x74455b60, priority=6, domain=nat-exempt-reverse, deny=false
        hits=61, user_data=0x744558f0, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip=Cust_B_LAN, mask=255.255.255.240, port=0
        dst ip=Cust_A_LAN, mask=255.255.255.0, port=0, dscp=0x0
Result:
input-interface: Cust_B
input-status: up
input-line-status: up
output-interface: Cust_A
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
I seemed that I had a nonat rule messing the communication between these interfaces. After removing it, the traffic was flowing just fine.
Thanks for your support.
Ron

ASA 5520 - LU allocate xlate failed - Failover unit reloads

We just had an issue with our failover unit reloading. In perusing the logs there were a number of %ASA-3-210007: LU allocate xlate failed, errors prior to the reload. These units had just had their OS upgraded to fix a DOS issue a few weeks ago. I have not seen the error since it reloaded. However, I was asked to report the issue just in case it is a bug in the new version of the OS.Two units in failover.
Cisco Adaptive Security Appliance Software Version 8.0(5)9
Device Manager Version 6.0(2)
Compiled on Mon 01-Feb-10 10:36 by builders
System image file is "disk0:/asa805-9-k8.bin"
Config file at boot was "startup-config"
CP-ASA up 17 days 21 hours
failover cluster up 17 days 22 hours
Hardware:   ASA5520, 512 MB RAM, CPU Pentium 4 Celeron 2000 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
                             Boot microcode   : CN1000-MC-BOOT-2.00
                             SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
                             IPSec microcode : CNlite-MC-IPSECm-MAIN-2.05
0: Ext: GigabitEthernet0/0 : address is 0025.45d7.6e62, irq 9
1: Ext: GigabitEthernet0/1 : address is 0025.45d7.6e63, irq 9
2: Ext: GigabitEthernet0/2 : address is 0025.45d7.6e64, irq 9
3: Ext: GigabitEthernet0/3 : address is 0025.45d7.6e65, irq 9
4: Ext: Management0/0       : address is 0025.45d7.6e66, irq 11
5: Int: Internal-Data0/0    : address is 0000.0001.0002, irq 11
6: Int: Internal-Control0/0 : address is 0000.0001.0001, irq 5
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs                : 150
Inside Hosts                 : Unlimited
Failover                     : Active/Active
VPN-DES                      : Enabled
VPN-3DES-AES                 : Enabled
Security Contexts            : 2
GTP/GPRS                     : Disabled
VPN Peers                    : 750
WebVPN Peers                 : 2
AnyConnect for Mobile        : Disabled
AnyConnect for Linksys phone : Disabled
Advanced Endpoint Assessment : Disabled
UC Proxy Sessions            : 2
This platform has an ASA 5520 VPN Plus license.
I noted a report on errors with verison 7 and a conflict between nat(0) and static commands. I don't show nat(0) being used on these units.
nat (public) 0 access-list NO_NAT
nat (public) 1 10.190.16.64 255.255.255.192
nat (public) 1 172.16.22.0 255.255.255.0
nat (dmz) 0 access-list NO_NAT
nat (dmz) 1 0.0.0.0 0.0.0.0
nat (csacelb) 0 access-list NO_NAT
nat (csacelb) 1 0.0.0.0 0.0.0.0
nat (app) 0 access-list NO_NAT
nat (app) 1 0.0.0.0 0.0.0.0
nat (db) 0 access-list NO_NAT
nat (db) 1 0.0.0.0 0.0.0.0
nat (internal) 0 access-list NO_NAT
nat (internal) 1 0.0.0.0 0.0.0.0
nat (management) 0 access-list NO_NAT
nat (management) 1 0.0.0.0 0.0.0.0
no crypto isakmp nat-traversal
static (app,dmz) 10.190.15.0 10.190.15.0 netmask 255.255.255.192
static (csacelb,public) 999.999.999.999 10.190.14.70 netmask 255.255.255.255 (The external address was replaced with 999.999.999.999 intentionally for this forum)
static (db,app) 10.190.16.0 10.190.16.0 netmask 255.255.255.192

Do you have any solution ? we have the same problem.
Thanks .

Performance Issue behind ASA 5520

Hi Community!
I've got an ASA 5520 (8.4.3) Failover Cluster.
Behind this ASA i have a couple of DMZ Networks. In one of these Networks (lets call it DMZ-A) i have an performance issue.
So, in DMZ-A i have 2 Windows2012R2 servers.
IP Server1: 10.0.233.10/24
IP Server2: 10.0.233.12/24
If i do an RDP session to Server1 from my Client Computer (at the inside Network - IP: 10.0.20.199) it is really slow. Also File Transfer is very slow. Ping gives me a "normal" replay.
If i do an RDP session to Server2 from my Client Computer everything works normal.
If i do an RDP session from Server2 to Server1 everything works normal.
I did a apcket capture to both servers, and when i analyse them with wireshark there is (at a sertain packet) a big difference. -> see attached files
ASA_10 -> 10.0.233.10
ASA_12 -> 10.0.233.12
Can anybody help me finding out whats going wong there?
Thanks a lot!!

Hi ... thanks for the answer.
Here is the Config. Hope i got all the relevant things in it.
Somehow the NAT statement causes the trouble:
object network 10.0.233.10
nat (dmz233,outside) static XXX.XXX.XXX.133
Because if i delete this statement, the RDP connection to the server works normal.
I delete all the network objects and object groups.
Also all the VPN configs are missing.
DELETED THE ASA CONFIG BECAUSE I SOLVED THE PROBLEM!!!! -> misconfiguration
Thanks !!

What is causing ASA 5520 v8.4 error 305006 for DNS traffic?

I implemented transparent mode NAT in single context mode on an ASA 5520 v8.4. Some connections are working well, but I am seeing others unable to resolve DNS. I am seeing lot of the following error messages:
Syslog ID 305006 regular translation creation failed for udp src inside: 10.x.x.x/x des outside:192.168.1.3/53
Any ideas on what I might look for as possible errors in my configuration?

I implemented transparent mode NAT in single context mode on an ASA 5520 v8.4. Some connections are working well, but I am seeing others unable to resolve DNS. I am seeing lot of the following error messages:
Syslog ID 305006 regular translation creation failed for udp src inside: 10.x.x.x/x des outside:192.168.1.3/53
Any ideas on what I might look for as possible errors in my configuration?

Connectivity Issue between ASA 5520 firewall and Cisco Call Manager

Recently i have installed ASA 5520 firewall, Below is the detail for my network
ASA 5520 inside ip: 10.12.10.2/24
Cisco Switch 3560 IP: 10.12.10.1/24 for Data and 10.12.110.2/24 for Voice
Cisco Call Manager 3825 IP: 10.12.110.2/24
The users and the IP phone are getting IP from the DHCP server which configured on cisco 3560 Switch.
the Default Gateway for Data user is 10.12.10.2/24 and
for the voice users is 10.12.110.2/24
now the problem is that the users is not able to ping 10.12.110.2 call manager. please if somebody can help in this regard. i will appreciate the prompt response against this issues.

Actually i don't wana to insert new subnet and complicate the nework. i need a simple way to solve the problem. below is the details for the asa 5520 config.
ASA Version 8.2(1)
name x.x.x.x Mobily
interface GigabitEthernet0/0
nameif inside
security-level 99
ip address 10.12.10.2 255.255.255.0
interface GigabitEthernet0/1
nameif outside
security-level 0
ip address x.x.x.x 255.255.255.252
object-group service DM_INLINE_SERVICE_1
service-object tcp-udp
service-object ip
service-object icmp
service-object udp
service-object tcp eq ftp
service-object tcp eq www
service-object tcp eq https
service-object tcp eq ssh
service-object tcp eq telnet
access-list RA_VPN_splitTunnelAcl_1 standard permit Inside-Network 255.255.255.0
access-list RA_VPN_splitTunnelAcl standard permit Inside-Network 255.255.255.0
access-list inside_nat0_outbound extended permit ip Inside-Network 255.255.255.0 10.12.10.16 255.255.255.240
access-list inside_nat0_outbound extended permit object-group DM_INLINE_SERVICE_1 10.12.10.16 255.255.255.240 Inside-Network 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip Inside-Network 255.255.255.0 10.12.10.16 255.255.255.240
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu mgmt 1500
ip local pool VPN-Pool 172.16.1.1-172.16.1.30 mask 255.255.255.0
ip local pool VPN-Users 10.12.10.21-10.12.10.30 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-641.bin
asdm history enable
arp timeout 14400
global (inside) 2 interface
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound_1
nat (inside) 1 Inside-Network 255.255.255.0
route outside 0.0.0.0 0.0.0.0 Mobily 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http Mgmt-Network 255.255.255.0 mgmt
http Inside-Network 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet Inside-Network 255.255.255.0 inside
telnet timeout 5
ssh Inside-Network 255.255.255.255 inside
<--- More ---> ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy RA_VPN internal
group-policy RA_VPN attributes
dns-server value 86.51.34.17 8.8.8.8
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value RA_VPN_splitTunnelAcl
username admin password LPtK/u1LnvHTA2vO encrypted privilege 15
tunnel-group RA_VPN type remote-access
tunnel-group RA_VPN general-attributes
address-pool VPN-Users
default-group-policy RA_VPN
tunnel-group RA_VPN ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:e5a64fa92ae465cd7dabd01ce605307d
: end

Cisco ASA 5520 traffic between interfaces

Hello,
I am new in the Cisco world , learning how everything goes. I have a Cisco ASA 5520 firewall that i am trying to configure, but i am stumped. Traffic does not pass trough interfaces ( i tried ping ) , although packet tracer shows everything as ok. I have attached the running config and the packet tracer. The ip's i am using in the tracer are actual hosts.
ciscoasa# ping esx_management 192.168.10.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.10.100, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
ciscoasa# ping home_network 192.168.10.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.10.100, timeout is 2 seconds:
Success rate is 0 percent (0/5)
Thank you in advance.

Hi,
Is this just a testing setup? I would suggest changing "internet" interface to "security-level 0" (just for the sake of identifying its an external interface) and not allowing all traffic from there.
I am not sure what your "packet-tracer" is testing. If you wanted to test ICMP Echo it would be
packet-tracer input home_network icmp 10.192.5.5 8 0 255 192.168.10.100
I see that you have not configured any NAT on the ASA unit. In the newer ASA software that would atleast allow communication between all interface with their real IP addresses.
I am not so sure about the older ASA versions anymore. To my understanding the "no nat-control" is default setting in your model which basically states that there is no need for NAT configurations between the interfaces the packet is going through.
Have you confirmed that all the hosts/servers have the correct default gateway/network mask configurations so that traffic will flow correctly outside their own network?
Have you confirmed that there are no firewall software on the actual server/host that might be blocking this ICMP traffic from other networks?
Naturally if wanted to try some NAT configurations you could try either of these for example just for the sake of testing
Static Identity NAT
static (home_network,esx_management) 192.168.5.0 192.168.5.0 mask 255.255.255.0
static (home_network,DMZ) 192.168.5.0 192.168.5.0 mask 255.255.255.0
static (home_network,management) 192.168.5.0 192.168.5.0 mask 255.255.255.0
OR
NAT0
access-list HOMENETWORK-NAT0 remark NAT0 to all local networks
access-list HOMENETWORK-NAT0 permit ip 192.168.5.0 255.255.255.255.0 192.168.10.0 255.255.255.0
access-list HOMENETWORK-NAT0 permit ip 192.168.5.0 255.255.255.255.0 192.168.20.0 255.255.255.0
access-list HOMENETWORK-NAT0 permit ip 192.168.5.0 255.255.255.255.0 192.168.1.0 255.255.255.0
nat (home_network) 0 access-list HOMENETWORK-NAT0
Hope this helps
- Jouni

Patch: CSCun25809, AnyConnect Password Management Fails with SMS Passcode for ASA 5520

Patch: CSCun25809, AnyConnect Password Management Fails with SMS Passcode for ASA 5520
Will this patch be installed in a version which I can use on ASA5520, if I understand the documentation correct, this patch is only installed in versions which are running on -X models of the ASA. 9.2, 9.3

Once the ASA has dynamic NAT enabled to an outside interface, routing between same security level will not work.
You need to add route exempt the inside interfaces to all private subnet.

DHCP question on VPN to ASA 5520

Our VPN uses the Microsoft VPN client to connect to an ASA 5520 running 8.0(3). Clients get address from our internal DHCP server. How do I get the ASA to send the client computer name in the DHCP request, rather the the group name and some number it appends to it? This is an issue for us because those entries show up as "rogue" registrations in DNS, because they don't match our naming structure.

Make sure if the client is forwarding it's name in the DHCP messages. Parameters can't be added at ASA.

ASA 5520 NAT 8.4

Similar Messages

Maybe you are looking for