ASA 8.4.x and ASDM 6.4x download?
Hi,
I search for the both files, because I want to configure one ASA with 8.2.1 and the other
ASA with a 8.4.x image to see the differences between both versions. But I don`t have
a account to download the ASA Image 8.4.x an the ASDM 6.4x to test it.
Is there a chance to get those Images without a Account.
BR
Hans-Juergen Guenter
No. Downloading ASA software images requires a service contract entitlement.
There is a lot of literature and other information available on the differences. For example:
https://supportforums.cisco.com/community/netpro/security/firewall?view=documents
Also be advised that ASA 9.0 was released just this week.
https://supportforums.cisco.com/thread/2179555?tstart=0
Hope this helps.
Similar Messages
-
ASA v9.0.1 and ASDM v7.0.1 released
Looks like v9 is now out...
http://www.cisco.com/en/US/docs/security/asa/asa90/release/notes/asarn90.pdf
Regards Simon
http://www.linksysinfo.orgThanks for spreading out the good news Simon.
People interested in these two releases can find them here.
ASA 9.0.1 and ASDM 7.0.1
Important points to consider before an upgrade to 9.0:
ASA and ASDM Compatibility
ASA OS
ASDM
ASA Model:
ASA 5505
ASA 5510, 5520, 5540
ASA 5550
ASA 5580
ASA 5512-X, 5515-X, 5525-X, 5545-X, 5555-X
ASA 5585-X
ASASM
ASA 1000V
ASA 9.0(1)
ASDM 7.0(1).
YES
YES
YES
YES
YES
YES
YES
No
Limitations and Restrictions
•Clientless SSL VPN with a self-signed certificate on the ASA—When the ASA uses a self-signed certificate or an untrusted certificate, Firefox 4 and later and Safari are unable to add security exceptions when browsing using an IPv6 address HTTPS URL (FQDN URL is OK): the "Confirm Security Exception" button is disabled. See: https://bugzilla.mozilla.org/show_bug.cgi?id=633001. This caveat affects all SSL connections originating from Firefox or Safari to the ASA (including clientless SSL VPN connections, and ASDM connections). To avoid this caveat, configure a proper certificate for the ASA that is issued by a trusted certificate authority. For Internet Explorer 9 and later, use compatibility mode.
•Citrix Mobile Receiver and accessing Virtual Desktop Infrastructure (VDI):
–CSD is not supported.
–HTTP redirect is not supported.
–Using Citrix Receiver mobile clients to access web interface of Citrix servers is not supported.
–Certificate or smart card authentication is not supported as a means of auto sign-on.
–You must install XML service and configure on XenApp and XenDesktop servers.
–Make sure the ports 443, 1494, 2598, and 80 are open on any intermediate firewalls between the ASA and the XenApp/XenDesktop server.
–The password-expire-in-days notification on tunnel group that is used by VDI is not supported.
•When configuring for IKEv2, for security reasons you should use groups 21, 20, 19, 24, 14, and 5. We do not recommend Diffie Hellman Group1 or Group2. For example, use
crypto ikev2 policy 10
group 21 20 19 24 14 5
As always make sure you are familiar with the upgrade procedure Upgrading the Software.
Important Notes
•Downgrading issues—Upgrading to Version 9.0 includes ACL migration (see the "ACL Migration in Version 9.0" section). Therefore, you cannot downgrade from 9.0 with a migrated configuration. Be sure to make a backup copy of your configuration before you upgrade so you can downgrade using the old configuration if required.
•Per-session PAT disabled when upgrading— Starting in Version 9.0, by default, all TCP PAT traffic and all UDP DNS traffic use per-session PAT (see the xlate per-session command in the command reference). If you upgrade to Version 9.0 from an earlier release, to maintain the existing functionality of multi-session PAT, the per-session PAT feature is disabled during configuration migration. The ASA adds the following deny rules:
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
To enable per-session PAT after you upgrade, enter:
clear configure xlate
The above deny rules are cleared so that only the default permit rules are still in place, thus enabling per-session PAT.
•No Payload Encryption for export—You can purchase some models with No Payload Encryption. For export to some countries, payload encryption cannot be enabled on the Cisco ASA 5500 series. The ASA software senses a No Payload Encryption model, and disables the following features:
–Unified Communications
–VPN
You can still install the Strong Encryption (3DES/AES) license for use with management connections and encrypted route messages for OSPFv3. For example, you can use ASDM HTTPS/SSL, SSHv2, Telnet and SNMPv3. You can also download the dynamic database for the Botnet Traffic Filer (which uses SSL) and redirect traffic to Cloud Web Security.
More information at:
Release Notes for the Cisco ASA Series, 9.0(x)
HTH.
Portu.
Please rate any helpful posts -
ASA 5505 unable to access ASDM ( just needs some ports ope and FWDing setup)
I was able to access the ASDM launcher in the browser yesterday via https://192.168.111.1/admin and I was stuck there as the browser version says that my ASA image does not work with my ASDM version... So i tried some trouble shooting and think that i may have changed the image to an image that does not exist. (I'm not sure where it is that I would actually place that image either) Now i am unable to access through the browser at all.
Anyways, I am ok with SSH/CLI and have been using my firewall in this manner. I am walking into this companies current configuration and simply need to do the following:
I need to OPEN ports 9000, 85, 40085, 49005 so that my mobile device can pull my security cameras in the office
I need to set port forwarding so that any connections that hit outside-in ip address 205.214.36.53:1610 >>> http://192.168.111.30:1610/AndroidWS/ for our new mobile CRM.
I have been through some of your related discussions and am falling short somewhere. Please help
here is my "show run" and my "dir"
ciscoasa(config)# show run
: Saved
ASA Version 9.0(2)
hostname ciscoasa
domain-name scec.local
enable password ol40hHpZTtZQFXMJ encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd ol40hHpZTtZQFXMJ encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif INSIDE
security-level 100
ip address 192.168.111.1 255.255.255.0
interface Vlan2
nameif OUTSIDE
security-level 0
ip address 205.214.236.50 255.255.255.240
boot system disk0:/asa902-k8.bin
boot system disk0:/asa825-k8.bin
boot system disk0:/asa831-k8.bin
ftp mode passive
dns domain-lookup INSIDE
dns domain-lookup OUTSIDE
dns server-group DefaultDNS
name-server 192.168.111.50
name-server 8.8.8.8
domain-name scec.local
object network LAN
subnet 192.168.111.0 255.255.255.0
object network SERVER1
host 192.168.111.50
object network SERVER1_PUBLIC
host 205.214.236.51
object network SERVER2
host 192.168.111.20
object network SERVER2_PUBLIC
host 205.214.236.52
object network SERVER3
host 192.168.111.30
object network SERVER3_PUBLIC
host 205.214.236.53
object network SERVER4
host 192.168.111.40
object network SERVER4_PUBLIC
host 205.214.236.54
object network SERVER5
host 192.168.111.10
object network SERVER5_PUBLIC
host 205.214.236.55
object-group service SERVER1_PORTS tcp
port-object eq www
port-object eq https
port-object eq smtp
port-object eq pop3
port-object eq imap4
port-object eq 3389
object-group service SERVER2_PORTS tcp
port-object eq 3389
object-group service SERVER3_PORTS tcp
port-object eq 3389
object-group service SERVER4_PORTS tcp
port-object eq 3389
object-group service SERVER5_PORTS tcp
port-object eq 3389
port-object eq www
port-object eq https
access-list OUTSIDE_IN extended deny ip 10.0.0.0 255.0.0.0 any log
access-list OUTSIDE_IN extended deny ip 172.16.0.0 255.240.0.0 any log
access-list OUTSIDE_IN extended deny ip 192.168.0.0 255.255.0.0 any log
access-list OUTSIDE_IN extended deny ip 127.0.0.0 255.0.0.0 any log
access-list OUTSIDE_IN extended deny ip 0.0.0.0 255.255.255.0 any log
access-list OUTSIDE_IN extended deny ip 244.0.0.0 255.255.255.240 any log
access-list OUTSIDE_IN extended deny ip host 255.255.255.255 any log
access-list OUTSIDE_IN extended permit icmp any any echo-reply
access-list OUTSIDE_IN extended permit icmp any any time-exceeded
access-list OUTSIDE_IN extended permit icmp any any unreachable
access-list OUTSIDE_IN extended permit tcp any object SERVER1 object-group SERVER1_PORTS
access-list OUTSIDE_IN extended permit tcp any object SERVER2 object-group SERVER2_PORTS
access-list OUTSIDE_IN extended permit tcp any object SERVER3 object-group SERVER3_PORTS
access-list OUTSIDE_IN extended permit tcp any object SERVER4 object-group SERVER4_PORTS
access-list OUTSIDE_IN extended permit tcp any object SERVER5 object-group SERVER5_PORTS
access-list inside-out extended permit ip any any
pager lines 24
logging asdm informational
mtu INSIDE 1500
mtu OUTSIDE 1500
ip audit name OUTSIDE_ATTACK attack action alarm drop
ip audit name OUTSIDE_INFO info action alarm
ip audit name INSIDE_ATTACK attack action alarm drop reset
ip audit name INSIDE_INFO info action alarm
ip audit interface INSIDE INSIDE_INFO
ip audit interface OUTSIDE OUTSIDE_INFO
ip audit interface OUTSIDE OUTSIDE_ATTACK
ip audit signature 2000 disable
ip audit signature 2001 disable
ip audit signature 2004 disable
ip audit signature 2005 disable
ip audit signature 6051 disable
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-509.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (INSIDE,OUTSIDE) source static SERVER1 SERVER1_PUBLIC
nat (INSIDE,OUTSIDE) source static SERVER2 SERVER2_PUBLIC
nat (INSIDE,OUTSIDE) source static SERVER3 SERVER3_PUBLIC
nat (INSIDE,OUTSIDE) source static SERVER4 SERVER4_PUBLIC
nat (INSIDE,OUTSIDE) source static SERVER5 SERVER5_PUBLIC
object network LAN
nat (INSIDE,OUTSIDE) dynamic interface
access-group inside-out in interface INSIDE
access-group OUTSIDE_IN in interface OUTSIDE
route OUTSIDE 0.0.0.0 0.0.0.0 205.214.236.49 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
aaa authorization exec LOCAL
http server enable
http 0.0.0.0 0.0.0.0 INSIDE
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 INSIDE
ssh 0.0.0.0 0.0.0.0 OUTSIDE
ssh timeout 5
ssh version 2
console timeout 0
dhcpd option 3 ip 192.168.111.1
dhcpd address 192.168.111.100-192.168.111.200 INSIDE
dhcpd dns 192.168.111.50 8.8.8.8 interface INSIDE
dhcpd enable INSIDE
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
username wti password OIEBfkGT1DRShCnN encrypted privilege 15
username admin password g/t7o/eHDKMomDrS encrypted privilege 15
username vpnuser password 8DcFkqJ9hi39UQw. encrypted privilege 15
username sysadmin password mi1AUI982JWkJuWt encrypted
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:6dd04d2527e7929343ebd090969e18a1
: end
ciscoasa(config)# dir
Directory of disk0:/
148 -rwx 15390720 09:08:54 Jul 31 2013 asa825-k8.bin
149 -rwx 27611136 09:43:48 Oct 31 2013 asa902-k8.bin
150 -rwx 2048 00:00:00 Jan 01 1980 FSCK0000.REC
20 drwx 2048 09:12:16 Jul 31 2013 coredumpinfo
151 -rwx 16280544 09:14:46 Jul 31 2013 asdm-645.bin
10 drwx 2048 09:19:42 Jul 31 2013 log
19 drwx 2048 09:20:08 Jul 31 2013 crypto_archive
153 -rwx 14240396 14:14:18 Jun 11 2014 asdm-631.bin
154 -rwx 4096 00:00:00 Jan 01 1980 FSCK0001.REC
155 -rwx 12998641 09:20:28 Jul 31 2013 csd_3.5.2008-k9.pkg
156 drwx 2048 09:20:30 Jul 31 2013 sdesktop
157 -rwx 6487517 09:20:32 Jul 31 2013 anyconnect-macosx-i386-2.5.2014-k9.pkg
158 -rwx 6689498 09:20:36 Jul 31 2013 anyconnect-linux-2.5.2014-k9.pkg
159 -rwx 4678691 09:20:38 Jul 31 2013 anyconnect-win-2.5.2014-k9.pkg
160 -rwx 4096 00:00:00 Jan 01 1980 FSCK0002.REC
161 -rwx 4096 00:00:00 Jan 01 1980 FSCK0003.REC
162 -rwx 4096 00:00:00 Jan 01 1980 FSCK0004.REC
163 -rwx 6144 00:00:00 Jan 01 1980 FSCK0005.REC
164 -rwx 6144 00:00:00 Jan 01 1980 FSCK0006.REC
165 -rwx 6144 00:00:00 Jan 01 1980 FSCK0007.REC
166 -rwx 22528 00:00:00 Jan 01 1980 FSCK0008.REC
167 -rwx 38912 00:00:00 Jan 01 1980 FSCK0009.REC
168 -rwx 34816 00:00:00 Jan 01 1980 FSCK0010.REC
169 -rwx 43008 00:00:00 Jan 01 1980 FSCK0011.REC
170 -rwx 2048 00:00:00 Jan 01 1980 FSCK0012.REC
171 -rwx 26624 00:00:00 Jan 01 1980 FSCK0013.REC
172 -rwx 2048 00:00:00 Jan 01 1980 FSCK0014.REC
173 -rwx 26624 00:00:00 Jan 01 1980 FSCK0015.REC
174 -rwx 2048 00:00:00 Jan 01 1980 FSCK0016.REC
175 -rwx 2505 09:46:08 Oct 31 2013 8_2_5_0_startup_cfg.sav
176 -rwx 1189 09:46:12 Oct 31 2013 upgrade_startup_errors_201310310946.log
177 -rwx 100 16:42:40 Jun 10 2014 upgrade_startup_errors_201406101642.log
178 -rwx 100 14:52:26 Jun 11 2014 upgrade_startup_errors_201406111452.log
127004672 bytes total (21886976 bytes free)
Please let me know if you need any other information from me so that i can get our mobile devices to connect to the new CRM from outside the network and allow the owner access on his mobile device to the company cameras.
************** (NOTE: I can do both of these things currently from within the network without any issues)*************
THANKSJgreene -
This doesn't specifically answer your question, but if you want to get ASDM functionality back you need to load a newer version onto flash memory and then point the ASA to that with the configuration command:
asdm image disk0:/asdm-version.bin
You are running ASA Version 9.0(2) so you need at least version 7 of ASDM to support that. Interestingly enough your "asdm image" statement in your config points to asdm-509.bin and you have asdm-631.bin and asdm-645.bin on flash. None of those will work. I suggest loading up asdm-721.bin and changing the asdm image statement accordingly. I am pretty sure a reboot is required after that is done.
Good Luck!
-Jeff -
upgraded to 8 and asdm 6 had
http server 444 found that I could no longer add subnet access
http x.x.x.x mask outside without first clearing the entire config, ading http server without a port adding the access then putting the new port back on. In addition, log just show denies when attempting to access asdm from outside though I have put in http 0.0.0.0 0.0.0.0 outside just to test. Any ideas?It appears that with asdm 6 and asa 8 it can distinquish between asdm access and web access. I have found it works fine w/o changing the port but doesn't if the port is changed.
-
Cisco ASA 5505 Ipsec VPN and random connection dropping issues.
Hello,
We are currently having issues with a ASA 5505 Ipsec VPN. It was configured about 7-8 months ago and has been running very well..up until the last few weeks. For some reason, the VPN tends to randomly disconnect any user clients connected a lot. Furthermore, sometimes it actually connects; however does not put us on the local network for some reason and unable to browse file server. We have tried rebooting the ASA a few times and our ISP Time Warner informed us there are no signs of packet loss but still unable to pinpoint the problem. Sometimes users close out of VPN client completely, reopen several times and then it works. However it's never really consistent enough and hasn't been the last few weeks. No configuration changes have been made to ASA at all. Furthermore, the Cisco Ipsec VPN client version is: 5.0.70
Directly below is our current running config (modded for public). Any help or ideas would be greatly appreciated. Otherwise, if everything looks good...then I will defer back to our ISP Time Warner:
: Saved
ASA Version 8.4(2)
hostname domainasa
domain-name adomain.local
enable password cTfsR84pqF5Xohw. encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 205.101.1.240 255.255.255.248
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server 192.168.2.60
domain-name adomain.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network SBS_2011
host 192.168.2.60
object network NETWORK_OBJ_192.168.2.0_24
subnet 192.168.2.0 255.255.255.0
object network NETWORK_OBJ_192.168.5.192_
27
subnet 192.168.5.192 255.255.255.224
object network Https_Access
host 192.168.2.90
description Spam Hero
object-group network DM_INLINE_NETWORK_1
network-object object SPAM1
network-object object SPAM2
network-object object SPAM3
network-object object SPAM4
network-object object SPAM5
network-object object SPAM6
network-object object SPAM7
network-object object SPAM8
object-group service RDP tcp
description Microsoft RDP
port-object eq 3389
access-list outside_access_in extended permit tcp object-group DM_INLINE_NETWORK_1 object SBS_2011 eq smtp
access-list outside_access_in extended permit tcp any object SBS_2011 eq https
access-list outside_access_in extended permit icmp any interface outside
access-list outside_access_in remark External RDP Access
access-list outside_access_in extended permit tcp any object SBS_2011 object-group RDP
access-list domain_splitTunnelAcl standard permit 192.168.2.0 255.255.255.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool test 192.168.10.1-192.168.10.5 mask 255.255.255.0
ip local pool VPN_Users 192.168.5.194-192.168.5.22
0 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static NETWORK_OBJ_192.168.2.0_24
NETWORK_OBJ_192.168.2.0_24
destination static NETWORK_OBJ_192.168.5.192_
27 NETWORK_OBJ_192.168.5.192_
27 no-proxy-arp route-lookup
object network obj_any
nat (inside,outside) dynamic interface
object network SBS_2011
nat (inside,outside) static interface service tcp smtp smtp
object network Https_Access
nat (inside,outside) static interface service tcp https https
nat (inside,outside) after-auto source dynamic any interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 205.101.1.239 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-reco
rd DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.2.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.2.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.160-192.168.2.19
9 inside
dhcpd dns 192.168.2.60 24.29.99.36 interface inside
dhcpd wins 192.168.2.60 24.29.99.36 interface inside
dhcpd domain adomain interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy domain internal
group-policy domain attributes
wins-server value 192.168.2.60
dns-server value 192.168.2.60
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value domain_splitTunnelAcl
default-domain value adomain.local
username ben password zWCAaitV3CB.GA87 encrypted privilege 0
username ben attributes
vpn-group-policy domain
username sdomain password FATqd4I1ZoqyQ/MN encrypted
username sdomain attributes
vpn-group-policy domain
username adomain password V5.hvhZU4S8NwGg/ encrypted
username adomain attributes
vpn-group-policy domain
service-type admin
username jdomain password uODal3Mlensb8d.t encrypted privilege 0
username jdomain attributes
vpn-group-policy domain
service-type admin
tunnel-group domain type remote-access
tunnel-group domain general-attributes
address-pool VPN_Users
default-group-policy domain
tunnel-group domain ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:e2466a5b754
eebcdb0cef
f051bef91d
9
: end
no asdm history enable
Thanks againHello Belnet,
What do the logs show from the ASA.
Can you post them ??
Any other question..Sure..Just remember to rate all of the community answers.
Julio -
Use Java version 6 update 7 and ASDM 7.1.3
ASDM access to 5500 using Java was just a frustrating experience. If you manage only one device you may not notice the pain. But if you are managing multiple devices with some device 'forbidden' to update ASA firmware, it is very frustrating. I spend few days looking at the issue and came to a conclusion and decided to post to guide all newer VPN admins who will go through the same pain and hopefully we can reduce some combined wasted time. No thanks to Cisco. This is not a guide but a start point of a dicussion and all input are welcome.
Recommended Beginning Setup for New Admin :
Java Version 6 Update 7
ASDM 7.1(3)
Reason for recommendation :
a. There doesn't seem to be any recommendation to where to start your ASDM journey. So here. Start from here. Attached PDF is simple list of Java version and its release date. http://en.wikipedia.org/wiki/Java_version_history Version 6 Update 7 is unique in that it is the last version to support Win 9x. Why is that important? ASDM is written on Win 9x interface.
b. It is a very old 2008 release. So why use such an old security cesspool of a product as a base? Security of newer version of Java isn't any better. Recommendation of Java use is to not use it. Java isn't secure. '.' But Cisco is insisting on using it. Shame on Cisco and this ASDM Java debacle is a shameful thing that Cisco even now can't careless.
c. Attached is the list of release date of Java and Cisco products. ASDMS for FWSM range from 2007-2010, ASA 5500 and PIX 2007-2008, ASA 2010-2013. 2008 seems to fit quite nicely in the middle. Very scientific .
Recommendation after gaining full access
a. Update ASA and ASDM firmware to latest. ASDM 7.1.3 has same interface as much older ASDM. Kudos to Cisco on that..
b. Write to US-CERT and CC Cisco to have them remove Java on their key platform. (Android too.. <- now, there's a joke!)UPDATE 2...
ASDM ASA management platform has a major flaw. Different version require different version of Java JRE(Runtime Environment). One would think latest version should be backward compatible. It isn't so.
So far Java Version 6 and Update 7 has been most compatible for my work. But NSP and other management console also require JRE and they unlike Cisco works well with the latest version but not with older version.
Keeping and working with multiple version of JRE is a pain because JRE does not have proper control to support that automatically. One way to accomplish launching different version of JRE instead of default is use of command-line.
In ASDM's shortcut icon properties, add version information in "target:". Find out JRE versions installed in your system under C:\Program Files (x86)\Java. Add option -version:"1.6.0_07" to specify which version to use. My example is JRE version 6 update 7.
Original line :
C:\Windows\SysWOW64\javaw.exe -Xms64m -Xmx512m -Dsun.swing.enableImprovedDragGesture=true -classpath lzma.jar;jploader.jar;asdm-launcher.jar;retroweaver-rt-2.0.jar com.cisco.launcher.Launcher
Modified line :
C:\Windows\SysWOW64\javaw.exe -version:"1.6.0_07" -Xms64m -Xmx512m -Dsun.swing.enableImprovedDragGesture=true -classpath lzma.jar;jploader.jar;asdm-launcher.jar;retroweaver-rt-2.0.jar com.cisco.launcher.Launcher
http://docs.oracle.com/javase/6/docs/technotes/tools/windows/java.html
#ASDM #JAVA #JRE -
CISCO ASA config issue (Remote management ASDM/SSH/etc)
I cant ping the device from 10.23.1.x either, I can ping it on 10.23.2.x though.
I have a couple ASA devices than I want to be able to manage across our network. I have two devices, Device A-10.23.1.10 the other is on 10.23.2.10, if I remote into a machine on the 10.23.2.x network I can connect through SSH and ASDM, but on the 10.23.1.x network I can not connect.. I have the ASDM configured to accept connection from both netowkrs. any idea why it does not work, the remote ASA is on the local/inside netwkr just on a diff subnet.
This topic first appeared in the Spiceworks Community -
CISCO ASA 5505 bandwidth Controll and split
Dear All,
Below am giving the infrastructure which i like to do please help me.
I Am Using Cisco ASA 5505 VPN Firewall and 6Mbps 1:1 dedicated internet connection.
in Lan Side we have 3 networks one for Internet Users one For VPN Users One for CCTV
i would like to split the 6Mbps bandwidth for these network 3 networks 3x2 each
each network use 2Mbps bandwidth. The VPN and CCTV Users use up to 6:00 pm after that the bandwidth will be free
after the 6:00 pm we need to use the the VPN and CCTV line bandwidth to the internet Users.
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
Compiled on Sun 06-Apr-08 13:39 by builders
System image file is "disk0:/asa724-k8.bin"
so please help me with suitable configuration for my purpose./please tell me which device will support for this/what is have to do for this.
Thanks
Lalu R.SThere's not much of that sort of functionality built into the ASA 5505 entry level firewall. To do that sort of thing in the firewall, you would have to move up to one of the newer 5500-X series with next generation firewall features and build a policy using Application Visibility and Control (AVC).
You can do some crude controls with QoS - the configuration guide chapter on doing that is here. -
Is ASA integration with ISE and RSA for 2 factor authentication a valid/tested design
Hi,
Customer currently uses ASA to directly integrate with RSA kind of solution to provide 2 factor authentication mechanism for VPN user access. We're considering to introduce ISE to this picture, and to offload posture analysis from ASA to ISE. And the flow we're thinking is to have ASA interface to ISE and ISE interface to RSA and AD backend infrastructure. And we still need the 2 factor authentication to work, i.e., customer gets a SMS code in addition to its login username and password. I'm wondering if ASA/ISE/RSA/AD integrated solution (and with 2 factor authentication to work) is a tested solution or Cisco validate design? Any potential issue may break the flow?
Thanks in advance for any input!
TinaHi,
I have an update for this quite broad question.
I have now came a bit further on the path.
Now the needed Radius Access Attribute are available in ISE after adding them in
"Policy Elements" -> "Dictionaris" -> "System" -> "Radius" -> "Cisco-VPN3000".
I added both the attribute 146 Tunnel-Group-Name which I realy need to achive what I want(select diffrent OTP-backends depending on Tunnel Group in ASA) and the other new attribute 150 Client-Type which could be intresting to look at as well.
Here the "Diagnostics Tools" -> "Generel tools" -> "TCP Dump" and Wireshare helped me understand how this worked.
With that I could really see the attributes in the radius access requests going in to the ASA.
Now looking at a request in "Radius Authentication details" I have
Other Attributes:
ConfigVersionId=29,Device Port=1025,DestinationPort=1812,RadiusPacketType=AccessRequest,Protocol=Radius,CVPN3000/ASA/PIX7.x-Tunnel-Group-Name=SMHI-TG-RA-ISESMS,CVPN3000/ASA/PIX7.x-Client-Type=,CPMSessionID=ac100865000006294FD60A7F,.....
Ok, the tunnel group name attribute seems to be understood correct, but Client-Type just say =, no value for that.
That is strange, I must have defined that wrong(?), but lets leave that for now, I do not really need it for the moment being.
So now when I have this Tunnel-Group-Name attribute available I want to use it in my Rule-Based Authentication Policy.
Problem now is that as soon as I in an expression add a criteria containing Cisco-VPN3000:CVPN3000/ASA/PIX7.x-Tunnel-Group-Name matches .* (just anything), then that row does not match any more. It still work matching against NAS-IP and other attributes.
What could it be I have missed?
Best regards
/Mattias -
I have read in a tutorial for the board 1200 that I can calibrate it with the Calibration and Configuration Palette in LabVIEW, but I do not have them and I could not download it to access its libraries, so I can only download the NI-DAQ software,What's my best choice and if it is to download the palette with its libraries, how can download it with them?I'd appreciate your answers
If you wish to use your 1200 device in LabVIEW, you must download and install NI-DAQ. When you install NI-DAQ, it will ask you if you would like to install support for LabVIEW. By installing this support, you will then have access to the DAQ pallette in LabVIEW. The DAQ pallette requires that you have NI-DAQ installed.
For more information on installing and using your device, you can refer to the DAQ Quick Start Guide. You can download it from:
http://digital.ni.com/manuals.nsf/14807683e3b2dd8f8625677b006643f0/0eca53fe80911b1f862568560068295d
Regards,
Erin -
I lost my old iphone and have a new 5s.. i need to sync to itunes. i had to donwload manually via tools but i didnt download all four files. now when i plug my phone into itunes it says there is an error bc i didnt download all the files. so when i go into itunes now and check for updates it says its up to date. the problem is with the phone support file i didnt download.
Does anyone know how to get back to the pop up that has the music player update and itunes update bc this is the only place i have seen "tools" to be able to manually update all four files....
***IF i completely uninstall itunes and reinstall will it still have all my songs, photos, apps etc... bc i need to sync my new phone to get all my stuff backthis is a follow up from the profane post earlier....
i have done this twice in two other posts..
here is my problem.. i started off trying to update itunes, it failed twice and said i needed to install manually via tools.
the only place to get to tools is the pop up box that appears when you click check for updates.. if there is an available update then the pop up shows up with the quick time and itunes files to download. so i finally figured that out. i clicked on tools and manual update, four files were saved to a file. Apple mobile device support, another one similar, itunes, and another one i cant remember. I only downloaded the itunes file seeing as though thats all i needed to accomplish in the first place.
so then i restarted my computer bc you need to reboot and then reopen itunes for update to take effect. once i have itunes back open i plugged in my new 5s which i am trying to sync to my computer to get all my stuff back bc i lost my previous phone over the weekend.. once i plugged the phone in an error stating i needed to unistall the apple mobile device support and itunes and then reinstall. well i dont know where those files were originally stored on my computer AND since my itunes was updated, just not the other 3 associated files, when i click check for updates it says its up to date and then pop up containing the quick time and itunes does not pop up thus i cant get back to the tools tab to manually save the 4 files again.
so i was just going to uninstall itunes all together and then i thought well what happens if it erases all my photos apps songs etc... which would defeat the whole purpose in the first place of me trying to sync my new phone to get all my stuff back.
so i literally have no idea what to do at this point.. if you have read this you are probably just as confused as me... -
I have a Dell Inspiron 1545 and I can't download Adobe flash or Adobe acrobat reader, when I try to play my games it says update flash and when I try to download it the screen comes up blank
Try the offline installers:
Flash Player for ActiveX (Internet Explorer)
Flash Player Plug-in (All other browsers)
For Adobe Reader: http://get.adobe.com/reader/enterprise/ -
I have bought a book from iBook. My credit card was charged and the book was downloaded. There is an error and the first 12 chapters are not there! The book has the prologue and info and then chapter thirteen. How do I get the whole book?
I have bought a book from iBook. My credit card was charged and the book was downloaded. There is an error and the first 12 chapters are not there! The book has the prologue and info and then chapter thirteen. How do I get the whole book?
-
In the past 6 years I have purchased many books from iTunes. I lost one of them and would like to download it again, however it is not showing up in my purchased screen. All of my music, movies, and shows are showing but none of my books. They do show up in my purchase history, how can I get them back? Help!
Welcome to the Apple Community.
So far as I am aware, books haven't been available for 6 years, so I'm wondering if you mean audiobooks.
Audiobooks are not currently part of the content that can be re-downloaded. -
Certain music pieces and apps won't download from my iPod to iTunes on my MacBook
I want to put what is on my iPod on my new MacBook, but certain pieces and apps won't download because my computer isn't authorized (so it will delete it from my iPod if I sync), but when it asks me to authorize it it uses an old Apple ID that doesn't exist anymore and to which I do not have access. Any ideas how to fix this? I just want to be able to sync my iPod with this computer without worrying about losing anything.
Check out this article:
iOS: How to transfer or sync content to your computer
Read the "iTunes and App Store Content" section, especially the "Transferring purchased content" link there.
Maybe you are looking for
-
How to add one more field in Internal table
Hi Experts i have declared an internal table DATA: lt_viqmel_iflos TYPE TABLE OF viqmel_iflos. viqmel_iflos is a Standared SAP Table, Now i want to add one more Text field in the internal table only, how to add in program. any one plz help. <REMOVED
-
XSLT does not put element into output
HI Gentlemen, I have the following code segment, reflecting a 4-level hierarchical structure. Only the first two levels are guaranteed to be present; the last two are optional (if pe:scheinuntergruppen_liste is present, then at least one pe:scheinunt
-
ThinkPad Twist S230u - Call using video doesn't work and the laptop make a lot of noise
Everytime I try to make any kind of call using video (through skype or any other software), the laptop just reset by itself. Also, everytime that I use the laptop it makes a lot of noite, it is uneareble!!! I would like to know what should I do, and
-
Never ending loop is driving me loopy!
If I spend anymore time on this I'll end up in a straight jacket(and then I might be able to get a job with Sun !) O.K. - here's the plan - the first loop should execute, evaluate if the value 'max' mod each value in the array is equal to 0. If none
-
Why do many websites not completely download
I get so frustrated trying to open most websites. They start to download then stop midstream. I regularly clear my cache and cookies but still doesn't help.