ASA - ASDM shows Red X Connection Disconnected.

                   Hi everyone,
I have ASDM connection to ASA.
On the bottom  i see Red X  with two computers that says
ASA Syslog connection
Status is UP
ASA Monitoring Connection disconnected????????
I still have connection to ASDM need to know what does it mean by connection disconnected?
Thanks
Mahesh

Hi Andrew,
Many thanks for useful link.
Regards
Mahesh

Similar Messages

  • After i upgrade my ASA 5505 from 8.2 to 8.4 i can no longer connect to ASDM. showing connecting ..... please wait for hours now

    after i upgrade my ASA 5505 from 8.2 to 8.4 i can no longer connect to ASDM. showing connecting ..... please wait for hours now

    Ron
    I recently looked at this question with a customer who has been running 8.2 and needs to get some features in newer code. We decided that it made more sense to go to 8.4 than to 8.3.
    HTH
    Rick

  • I have a red x showing in the connection box of ePrint - HP 8600 AIO N911n. Why?

    I have a red x showing in the connection box of ePrint - HP 8600 AIO N911n.  Why?

    Hi there, do you mean there is a red X on the printers front panel display?
    If my reply helped you, feel free to click on the Kudos button (hover over the "thumbs up").
    If my reply solved your problem please click on the Accepted Solution button so other Forum users may benefit from viewing the post.
    I am an HP employee.

  • I have Power Mac G5 1.8 single. I have a problem with ethernet port, before it was working with the internet, but now i shows it is connected even the cable is disconnected. I'm running Leopard 10.5. any help

    I have Power Mac G5 1.8 single. I have a problem with ethernet port, before it was working with the internet, but now i shows it is connected even the cable is disconnected. I'm running Leopard 10.5. any help

    Reset the PRAM.
    http://support.apple.com/kb/HT1379
    If that fails, reset the PMU.
    Scroll down the following page and click the G5 link for instructions:
    http://support.apple.com/kb/ht1939

  • Plssss help i beg all of u after hard reset my iphone got stuck with an apple symbol i thought it will get on and now the battery got empty and pressing power on button it switch on showing red battery and gets off and also its not connecting to my l

    Re: plssss help i beg all of u after hard reset my iphone got stuck with an apple symbol i thought it will get on and now the battery got empty and pressing power on button it switch on showing red battery and gets off and also its not connecting to my la
    its not connecting y?i think its software got corrupted,i think i should charge it first with a battery charger and when apple logo appears i should connect with pc,but i dont know how 2 open the back cover and how 2 remove the battery,i phone battery is removable or not?i mean it is fiz or wot?

    Recharge.  Reset.  Restore.

  • MY IPOD NANO 6TH GEN. SHOWS IT IS CONNECTED IN ITUNES, BUT WHEN I ATTEMP TO SYNC MUSIC IT DISCONNECTS

    My ipod nano 6th gen shows it is connected in itunes, but when I try to sync music it disconnects.Why?

    Have you gone into Tones tab to check the box SYNC TONES?  Is your ringtone less than 40secs?

  • Solution Manager - EarlyWatch Alert shows red flag for managed system.

    Hi Guys,
    I tried to fix EarlyWatch alert report for Managed systems of QA and Dev which showed red flag on SolMan in DSWP. While trying to generate BACK RFC Destination to SolMan for QA and Dev, it messed up the EarlyWatch alert reports of Prod which was successfully working upto this point. And now the red flag appears for Prod system on SolMan in DSWP instead of two bottle sign.
    As for why Dev and QA did not work, I found out it was NONE internal RFC popped whenever I tried to choose the RFC to connect to SolMan while Prod which was working fine before always showed BACK rfc. That's why I tried to fix BACK rfc for Dev and QA.
    Please help me to fix these EWA problems.
    Thanks,
    Modena

    Hi Modena,
    Please see the link below for this specific issue:
    http://wiki.sdn.sap.com/wiki/pages/viewpage.action?pageId=228262728

  • Snapshot agent showing red mark in replication monitor!!!(Merge replication)

    few days before snapshot agent showing red mark in replication monitor without any changes...
    synchronizing from publisher to subscribe working fine...
    and how to clean up snapshot agent job history...
    plz give me a solution...
    Thanks in advance.......

    error:
    The replication agent has not logged a progress message in 5 minutes. This might indicate an unresponsive agent or high system activity. Verify that records are being replicated to the destination and that connections to the Subscriber, Publisher, and Distributor
    are still active.
    snapshot agent showing red mark...
    Hi Baraiya Kirit,
    According to the error message, the issue could be caused by that the agent is busy or the agent cannot log in to one of the computers in the topology.
    To troubleshoot this issue, please perform the following steps. For more details, please review this article:
    MSSQL_ENG020554.
    • If the agent has stopped, please restart it and check if the error still occurs.
    • If this error is raised frequently because the agent is busy:
    You might need to redesign your application so that the agent spends less time processing.
    You can increase the interval at which agent status is checked using the Job Properties dialog box.
    • If an agent cannot log in to one of the computers in the topology:
    We recommend that the -LoginTimeOut value be set lower than the interval at which the replication agent checkup job runs.
    There is also a similar blog for your reference.
    http://maginaumova.com/the-replication-agent-has-not-logged-a-progress-message-in-10-minutes/
    Thanks,
    Lydia Zhang

  • Ipod just keeps connecting/disconnecting. any thoughts?

    here's the story. my ipod died. i upgraded to itunes 7. still was not working, i go to apple and get a refurbished one. the new one keeps connecting/disconnecting. when i open my computer, it shows it just blinking like its there, then its not. does not show in itunes, but half the time says do not disconnect.
    here's where it gets weird. the USB port runs other devices fine. i plugged my ipod into a friends PC and could put music on it. i plugged my friends ipod into my PC and it shows up fine. i've swapped the ipod USB cord with my friend and it still does the same thing. so its not the ipod, its not my comp. and its not my itunes. anyone even want to attempt? i'm at my wits end here.

    Try forcing the iPod into Disk Mode using the instructions in this Apple support document.
    Putting iPod into Disk Mode
    If you can successfully do that, it should keep the iPod mounted on your PC long enough for you to perform a restore of it via iTunes.
    Restoring iPod to factory settings
    B-rock

  • Flex showing up as connected... I don't have a Fitbit

    Since Yosemite I've been leaving Bluetooth on (for Handoff), and I've noticed nearly every day that a device called "Flex" connects. After a quick Google search it seems to be a Fitbit. I don't have a Fitbit, but live in an apartment complex, so I assume it's one of my neighbors. I can disconnect it, but it keeps connecting again. I've never had a Fitbit, so I'm not sure how it's paired. Is there any way I can block it from connecting?

    I've never connected a Fitbit to my computer, USB or Bluetooth, but it shows up as connected/paired under the Bluetooth icon in the menubar. I can choose "Disconnect", but after a while I see it is connected again. I assume it can't access anything on my computer, but I still don't like that it keeps connecting without my permission.

  • ASA not showing CPU Usage

    HI,
    I was polling my ASA on OP manager which was reside on INSIDE zone now we move OP manager on DMZ. Now ASA not showing ACTIVE CONNECTION and CPU Usage in OP manager.
    below are snmp configuration.
    snmp-server host DMZ A.B.C.D community cisco version 2c
    snmp-server enable traps
    snmp-server community cisco
    and recieve a mention log on ASA during polling ASA on OP manager (NMS).
    Kindly advice in this regards.
    Regards,
    Arshad Ahmed

    Any one kindly reply

  • My Passport Essential constant connect disconnect on some windows 8.1 machines

    Hi All, I have a 500 GB My Passport Essential, it works fine on my win 7 laptop, and my win 8.1 laptop, but on my win 8.1 pc that I recently built it constantly connect and disconnects. I have tried disabling the hard drive sleep mode settings in power settings, tried using WD Drive Utilities on Win 7 but it wouldnt recognise the drive. Turning off the sleep mode settings did make it show up for a very short while, but after that it was back to connecting and disconnecting. The hdd light turns on, I can hear the drive spinning, and I can hear the connect/disconnect sounds from windows. Any ideas?

    Hi, welcome to the community.
    It seems might be a power issue or the USB port in the board. Have you tried using another port and another cable? Also making sure in the power settings that the USB are not set to be turned off.

  • TS1398 I have an iPad 2 that is updated and using 6.0.1. It is connecting to my wifi just fine. I just purchased a 4th generation iPad. It shows it is connected to the same wifi, same strong signal, but it will not work. HELP!!!

    I have an iPad 2 that is updated and using 6.0.1. It is connecting to my wifi just fine. I just purchased a 4th generation iPad. It shows it is connected to the same wifi, same strong signal, but it will not work. HELP!!!

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    iOS 6 Wifi Problems/Fixes
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Novell client still show red "N", does ZCM Agent work ?

    Hi
    my customer has some workstation login slow.
    User type his username & password and summit it, Novell client show red "N" about 4 ~7 mins...when red "N" disappear, it will login to desktop about 15-20 seconds...
    I want to ask...when red "N" icon still show...Whether the Novell client still try to connect to server or not ? and that time, if ZCM Agent (CASA module) still waiting capture username/password or it has capture these infromation to CASA server ??
    Because I want to clear if workstation login slow by ZCM agent .
    wyldkao

    Hi Shaun
    Thanks For your great reply.
    I find a troubleshooting section in ZCM installation Guide , about "Unable to install NetIdentity from Novell Client 32 on a device that has ZENworks installed", the section was be record from 10.1 to 11.1. The Netidentity has a Install-Check action for checking Whether Local_Machine\Software\zenworks exist or not....but ZCM 10.3 or later use Local_Machine\Software\ZCM, not useing "zenworks", so Netidentity could install evenif ZCM agent installed.
    I know ZDM agent has some issue with Netidenty...but I do know why ZCM installation still record it....even ZCM11.1 installation Guide. Could you help me clear whether Netidentity agent will effect ZCM Agent or not ?? Because I could not find any document that could provide any message it will effect "ZCM" function
    thanks!!
    wyldkao

  • My ipod is showing a disabled connect to itunes.  When I try to get support Apple asks for my serial number-but I can't do anything.

    My ipod touch is showing a disabled connect to itunes message.  I've tried to get some support on itunes, however, I can not turn the ipod on to get the serial number.

    Apple shuld not be required.
    Disabled
    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    iOS: Wrong passcode results in red disabled screen                         
    If recovery mode does not work try DFU mode.                        
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings        
    For how to restore:
    iTunes: Restoring iOS software
    To restore from backup see:
    iOS: How to back up     
    If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
    You can redownload most iTunes purchases by:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store        
    If needed, you can find the SN by:
    iOS: How to find the serial number, IMEI, MEID, CDN, and ICCID number

Maybe you are looking for