ASA interim version

Have anyone run version 8.6(1)2 in production? Is there any issue?
Sent from Cisco Technical Support iPad App

Here is the release notes of 8.6:
www.cisco.com/en/US/docs/security/asa/asa84/release/notes/asarn86.html
HTH
Mohammad.

Similar Messages

  • ASA 5505 version 9.1 in extended access-list I can add interface name as destination??

    Hi All,
    I'm adding extended ACL on the ASA 5505 version 9.1 and found that in the source or destination field I can specify interface name instead of object, host/network but can't find it documented anywhere and what is the behavior of that?
    access-list VOICE_IN extended permit ip object obj-VOICE-LAN interface OUTSIDE
    Is it matching the egress interface or what?

    Use the interface name rather than IP address to match traffic based
    on which interface is the source or destination of the traffic. You must
    specify the interface keyword instead of specifying the actual IP
    address in the ACL when the traffic source is a device interface. For
    example, you can use this option to block certain remote IP addresses
    from initiating a VPN session to the ASA by blocking ISAKMP. Any
    traffic originated from or destined to the ASA, itself, requires that you
    use the access-group command with the control-plane keyword.

  • ASA 5505 version 9.1(4) NAT issue

    Hi,
    I am using ASA 5505 version 9.1(4) and using dynamic NAT command to NAT(PAT) inside subnet 192.168.3.0/24 with outside interface 192.168.100.2/24
    But unable to ping from inside host to internet or router interface 192.168.100.1 . Please suggest the show running is mentioned below.
    Following is the logical diagram
                                          192.168.100.1/24                          192.168.100.2/24                192.168.3.1                          
      Internet(ISP) ------------------->------------------ Router------------------------->(e0/0)  ASA 5505 (9.1) eth0/4 ----- ---------- Host (192.168.3.22)
    ASA Version 9.1(4)
    hostname ciscoasa
    enable password 2KFQnbNIdI.2KYOU encrypted
    xlate per-session permit tcp any4 any4
    xlate per-session permit udp any4 any4
    names
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ciscoasa(config)# object network Generic_All_Network
    ciscoasa(config-network-object)# sub
    ciscoasa(config-network-object)# subnet 0.0.0.0 0.0.0.0
    ciscoasa(config-network-object)# ex
    ciscoasa(config)# nat (inside,outside) source dynamic Generic_All_Network inte$
    ciscoasa(config)#
    ciscoasa(config)#
    ciscoasa(config)# wr
    Building configuration...
    Cryptochecksum: fe5175c6 25dfd45a 117bd6e3 867486db
    3211 bytes copied in 1.120 secs (3211 bytes/sec)
    [OK]
    ciscoasa(config)# sh run
    : Saved
    ASA Version 9.1(4)
    hostname ciscoasa
    enable password 2KFQnbNIdI.2KYOU encrypted
    xlate per-session permit tcp any4 any4
    xlate per-session permit udp any4 any4
    names
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.3.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address 192.168.100.2 255.255.255.0
    ftp mode passive
    object network inside_hosts
    subnet 192.168.3.0 255.255.255.0
    object network Generic_All_Network
    subnet 0.0.0.0 0.0.0.0
    access-list inbound extended permit ip any any
    access-list inbound extended permit icmp any4 any4
    access-list inside_access_in extended permit ip 192.168.3.0 255.255.255.0 any
    pager lines 24
    logging enable
    logging asdm informational
    mtu outside 1500
    mtu inside 1500
    ip verify reverse-path interface outside
    ip verify reverse-path interface inside
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    arp permit-nonconnected
    nat (inside,outside) source dynamic Generic_All_Network interface
    object network inside_hosts
    nat (inside,outside) dynamic interface
    access-group inbound in interface outside
    access-group inside_access_in in interface inside
    route outside 0.0.0.0 0.0.0.0 192.168.100.1 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    http server enable
    http 192.168.3.0 255.255.255.0 inside
    http 0.0.0.0 0.0.0.0 outside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec security-association pmtu-aging infinite
    crypto ca trustpool policy
    telnet timeout 5
    ssh timeout 5
    ssh key-exchange group dh-group1-sha1
    console timeout 0
    dhcpd auto_config outside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    call-home reporting anonymous prompt 2
    Cryptochecksum:fe5175c625dfd45a117bd6e3867486db
    : end

    yep I have already removed  nat (inside,outside) source dynamic Generic_All_Network interface
    Following is the latest show-running
    ciscoasa(config)# sh run
    : Saved
    ASA Version 9.1(4)
    hostname ciscoasa
    enable password 2KFQnbNIdI.2KYOU encrypted
    xlate per-session permit tcp any4 any4
    xlate per-session permit udp any4 any4
    names
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.3.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address 192.168.100.2 255.255.255.0
    ftp mode passive
    object network inside_hosts
    subnet 192.168.3.0 255.255.255.0
    access-list inbound extended permit ip any any
    access-list inbound extended permit icmp any4 any4
    access-list inside_access_in extended permit ip 192.168.3.0 255.255.255.0 any
    access-list capi extended permit ip host 192.168.3.22 host 192.168.100.1
    access-list capi extended permit ip host 192.168.100.1 host 192.168.3.22
    access-list capo extended permit ip host 192.168.100.2 any
    access-list capo extended permit ip any host 192.168.100.2
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip verify reverse-path interface inside
    ip verify reverse-path interface outside
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    arp permit-nonconnected
    object network inside_hosts
    nat (inside,outside) dynamic interface
    access-group inside_access_in in interface inside
    access-group inbound in interface outside
    route outside 0.0.0.0 0.0.0.0 192.168.100.1 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    http server enable
    http 192.168.3.0 255.255.255.0 inside
    http 0.0.0.0 0.0.0.0 outside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec security-association pmtu-aging infinite
    crypto ca trustpoint _SmartCallHome_ServerCA
    crl configure
    crypto ca trustpool policy
    crypto ca certificate chain _SmartCallHome_ServerCA
    certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
        308205ec 308204d4 a0030201 0202106e cc7aa5a7 032009b8 cebcf4e9 52d49130
        0d06092a 864886f7 0d010105 05003081 ca310b30 09060355 04061302 55533117
        30150603 55040a13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
        13165665 72695369 676e2054 72757374 204e6574 776f726b 313a3038 06035504
        0b133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
        20617574 686f7269 7a656420 75736520 6f6e6c79 31453043 06035504 03133c56
        65726953 69676e20 436c6173 73203320 5075626c 69632050 72696d61 72792043
        65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
        30303230 38303030 3030305a 170d3230 30323037 32333539 35395a30 81b5310b
        30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
        496e632e 311f301d 06035504 0b131656 65726953 69676e20 54727573 74204e65
        74776f72 6b313b30 39060355 040b1332 5465726d 73206f66 20757365 20617420
        68747470 733a2f2f 7777772e 76657269 7369676e 2e636f6d 2f727061 20286329
        3130312f 302d0603 55040313 26566572 69536967 6e20436c 61737320 33205365
        63757265 20536572 76657220 4341202d 20473330 82012230 0d06092a 864886f7
        0d010101 05000382 010f0030 82010a02 82010100 b187841f c20c45f5 bcab2597
        a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
        9c688b2e 957b899b 13cae234 34c1f35b f3497b62 83488174 d188786c 0253f9bc
        7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
        15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
        63cd1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8
        18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
        4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
        81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 02030100 01a38201 df308201
        db303406 082b0601 05050701 01042830 26302406 082b0601 05050730 01861868
        7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1d130101
        ff040830 060101ff 02010030 70060355 1d200469 30673065 060b6086 480186f8
        45010717 03305630 2806082b 06010505 07020116 1c687474 70733a2f 2f777777
        2e766572 69736967 6e2e636f 6d2f6370 73302a06 082b0601 05050702 02301e1a
        1c687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
        03551d1f 042d302b 3029a027 a0258623 68747470 3a2f2f63 726c2e76 65726973
        69676e2e 636f6d2f 70636133 2d67352e 63726c30 0e060355 1d0f0101 ff040403
        02010630 6d06082b 06010505 07010c04 61305fa1 5da05b30 59305730 55160969
        6d616765 2f676966 3021301f 30070605 2b0e0302 1a04148f e5d31a86 ac8d8e6b
        c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
        69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
        1b311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301d0603
        551d0e04 1604140d 445c1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355
        1d230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300d0609
        2a864886 f70d0101 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80
        4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
        b2227055 d9203340 3307c265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
        6decd018 7d494aca 99c71928 a2bed877 24f78526 866d8705 404167d1 273aeddc
        481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
        b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
        5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
        6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
        6c2527b9 deb78458 c61f381e a4c4cb66
      quit
    telnet timeout 5
    ssh timeout 5
    ssh key-exchange group dh-group1-sha1
    console timeout 0
    dhcpd auto_config outside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    call-home reporting anonymous
    Cryptochecksum:b5958fd342c81895465887026d1423b3
    : end

  • ASA 5505 version 8.2 Base License - getting more anyconnect licensing

    Is it possible to increase the number of IPSec VPN peers from 10 to 25 on an ASA 5505 version 8.2 with the base license, simply by adding
    L-ASA-AC-E-5505= and not having to upgrade to the security plus license?
    ASA 5505
    Base License: 10 sessions (25 combined IPSec and SSL VPN1 ).
    Security Plus License: 25 sessions (25 combined IPSec and SSL VPN1).
    Thank You

    I tried  reloading the ASA but to no avail. The ISP cleared their ARP cache as well.While I had the ISP online and they didn't see the printers DHCP request.
    Of course this is all remote but I can see the interface state change when I have the users turn the printer off then on. When I plug the printer into the local LAN it obtains a local DHCP address and I can access it.
    So I'm thinking the printers DHCP request is being blocked at the ASA or somthing else is causing the issue. I am at a loss.

  • Configurate cisco ipsec vpn client at asa 5505 version 8.4

    Hi dear. I want to configurate cisco ipsec vpn client at asa 5505. At my asa the software version is 8.4.
    please provide me a link or some material to config ipsec vpn client at asa 5505 version 8.4
    thank you.

    are you looking for vpn client .pcf file or the configuration on ASA (ASDM) ?
    what version of vpn client ?

  • ASA 5520 VERSION 8.2 UPGRADE TO 9.0

    Hello friends,
    I am considering to perform an upgrade of my ASA 5520 with versión 8.2 to 9.0, so I will enjoy the benefits of anyconnect for mobile devices. I clearly understand that I must pay special attention to:
    NAT Rules.
    RAM Memory: 2 GB.
    Adding the part numbers to power on the newest versions of anyconnect and for mobile devices
    L-ASA-AC-E-5520= ASA-AC-M-5520=
    am I missing any other thing? Flash requirement? Or to pay attention to some other configurations? 
    Any comment or documentation will be appreciated.
    Regards!

    You can run the latest AnyConnect client - including mobile clients - with those licenses even on an ASA with the current  8.2 code - 8.2(5) as of now. While it's a bit old and lacking some of the newer features, it's a solid and stable release.
    That would save you the trouble of migrating your NAT configuration (and other bits) and upgrading memory.
    Since the ASA 5500 series (5510, 5520 etc.) is past End of Sales you have a limited future on those platforms. For instance, ASA 9.1(x) is the last set of code releases that will be available for them. (The current software on the 5500-X is 9.3(1).)

  • ASA 5510 - Version 8.2(1) - SSH, ICMP and NAT not working

    I have an ASA 5510 using version 8.2(1) and I have enabled ssh, icmp and they work from the inside network but not from the outside network. 
    Further to this, I exposed one site from the inside interface on the ASA (192.168.1.100) to outside (1.1.1.7) using NAT and it is not pingable nor accessible from the outside. I also allowed SSH from the outside network to the external IP addresses of the ASA and it is not working either.  Any ideas what I could be missing in my configuration?  I bolded the configurations involved in the ASA running configuration I copied below (please note I have replaced the real IP addresses with 1.1.1.x and 2.2.2.x):
    ASA Version 8.2(1)
    hostname fw
    domain-name net.com
    enable password eYKAfQL1.ZSbcTXZ encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    dns-guard
    interface Ethernet0/0
    description Primary Outside (Internet)
    speed 10
    duplex full
    nameif outside
    security-level 0
    ip address 1.1.1.5 255.255.255.240
    ospf cost 10
    interface Ethernet0/1
    description inside
    speed 100
    duplex full
    nameif inside
    security-level 100
    ip address 192.168.1.254 255.255.255.0
    ospf cost 10
    interface Ethernet0/2
    description WLAN
    nameif WLAN
    security-level 100
    ip address 192.168.108.240 255.255.255.0
    ospf cost 10
    interface Ethernet0/3
    description Secondary Outside (Internet)
    speed 100
    duplex full
    nameif WAN2
    security-level 0
    ip address 2.2.2.133 255.255.255.192
    interface Management0/0
    description LAN/STATE Failover Interface
    time-range after_hours
    periodic weekdays 7:00 to 23:00
    boot system disk0:/asa821-k8.bin
    no ftp mode passive
    clock timezone EST -5
    clock summer-time EDT recurring
    dns domain-lookup WLAN
    dns server-group DefaultDNS
    retries 3
    timeout 5
    name-server 8.8.8.8
    name-server 206.191.0.210
    name-server 4.2.2.1
    name-server 4.2.2.2
    domain-name net.com
    access-list WAN2_access_in extended permit icmp any any echo-reply
    access-list WAN2_access_in extended permit icmp any any time-exceeded
    access-list WAN2_access_in extended permit icmp any any source-quench
    access-list WAN2_access_in extended permit icmp any any unreachable
    access-list WLAN_access_in extended permit icmp any any echo-reply
    access-list WLAN_access_in extended permit icmp any any time-exceeded
    access-list WLAN_access_in extended permit icmp any any source-quench
    access-list WLAN_access_in extended permit icmp any any unreachable
    access-list WLAN_access_in extended permit tcp host 192.168.1.100 eq ssh any
    access-list WLAN_access_in extended permit tcp 192.168.1.0 255.255.255.0 host 192.168.1.100 eq ssh
    access-list WLAN_access_in extended permit ip any any
    access-list time_based extended permit ip any any time-range after_hours
    access-list split_tunnel standard permit host 206.191.0.210
    access-list split_tunnel standard permit host 206.191.0.140
    access-list split_tunnel standard permit host 207.181.101.4
    access-list split_tunnel standard permit host 207.181.101.5
    access-list split_tunnel standard permit 192.168.1.0 255.255.255.0
    access-list outside_access_in extended permit icmp any any echo-reply
    access-list outside_access_in extended permit icmp any any time-exceeded
    access-list outside_access_in extended permit icmp any any
    access-list outside_access_in extended permit tcp any host 1.1.1.7 eq ssh
    access-list inside_access_in extended permit ip any any
    access-list inside_access_in extended permit tcp any host 192.168.1.100 eq ssh
    access-list inside_access_in extended permit icmp any any
    access-list inside_access_in extended permit icmp 192.168.1.0 255.255.255.0 any
    access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any
    access-list inside_access_in extended permit tcp 192.168.1.0 255.255.255.0 host 192.168.1.100 eq ssh
    pager lines 20
    logging enable
    logging asdm informational
    mtu outside 1500
    mtu inside 1500
    mtu WLAN 1500
    mtu WAN2 1500
    ip local pool DHCP 192.168.1.245-192.168.1.252 mask 255.255.255.0
    ip verify reverse-path interface outside
    ip verify reverse-path interface WAN2
    failover
    failover lan unit secondary
    failover lan interface FO Management0/0
    failover key *****
    failover link FO Management0/0
    failover interface ip FO 192.168.255.171 255.255.255.0 standby 192.168.255.172
    icmp unreachable rate-limit 1 burst-size 1
    icmp permit any outside
    icmp permit any inside
    icmp permit any WLAN
    icmp permit any WAN2
    asdm image disk0:/asdm-621.bin
    asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    global (WAN2) 1 interface
    nat (inside) 1 192.168.1.0 255.255.255.0
    nat (WLAN) 1 192.168.108.0 255.255.255.0
    static (inside,outside) 1.1.1.7 192.168.1.100 netmask 255.255.255.255
    access-group outside_access_in in interface outside
    access-group inside_access_in in interface inside
    access-group WLAN_access_in in interface WLAN
    access-group WAN2_access_in in interface WAN2
    route outside 0.0.0.0 0.0.0.0 1.1.1.1 1
    route WAN2 0.0.0.0 0.0.0.0 2.2.2.129 254
    route inside 192.168.1.100 255.255.255.255 192.168.1.0 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-record DfltAccessPolicy
    aaa authentication ssh console LOCAL
    http server enable
    http 192.168.108.0 255.255.255.0 WLAN
    http 192.168.1.0 255.255.255.0 inside
    http 192.168.1.101 255.255.255.255 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    sla monitor 123
    type echo protocol ipIcmpEcho 4.2.2.2 interface outside
    num-packets 3
    timeout 1000
    frequency 3
    service resetoutside
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    track 1 rtr 123 reachability
    no vpn-addr-assign aaa
    no vpn-addr-assign dhcp
    telnet timeout 5
    ssh scopy enable
    ssh 2.2.2.132 255.255.255.255 outside
    ssh 69.17.141.134 255.255.255.255 outside
    ssh 192.168.1.0 255.255.255.0 inside
    ssh 192.168.1.100 255.255.255.255 inside
    ssh 192.168.108.0 255.255.255.0 WLAN
    ssh timeout 60
    console timeout 0
    management-access inside
    dhcpd address 192.168.108.11-192.168.108.239 WLAN
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    ntp authenticate
    ntp server 128.100.100.128
    ntp server 132.246.168.148
    ntp server 128.100.56.135
    tftp-server inside 192.168.1.100 /
    webvpn
    group-policy Wifi internal
    group-policy Wifi attributes
    wins-server none
    dns-server value 206.191.0.210 206.191.0.140
    vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value split_tunnel
    tunnel-group Wifi type remote-access
    tunnel-group Wifi general-attributes
    address-pool DHCP
    default-group-policy Wifi
    tunnel-group Wifi ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect netbios
      inspect rsh
      inspect rtsp
      inspect skinny 
      inspect esmtp
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect sip 
      inspect xdmcp
      inspect icmp
      inspect icmp error
    policy-map type inspect dns migrated_dns_map_1
    parameters
      message-length maximum 512
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:ac25ef0642e0ecb8f0ef63219833f3ae
    : end
    asdm image disk0:/asdm-621.bin
    asdm location 192.168.1.245 255.255.255.255 inside
    asdm location 192.168.1.252 255.255.255.255 inside
    asdm history enable

    Hi,
    I can't see any problems right away in the configuration.
    I guess we could start by using the "packet-tracer" to simulate the SSH and ICMP through the firewall
    packet-tracer input outside tcp 1.1.1.1 12345 22
    packet-tracer input outside icmp 1.1.1.1 8 0
    Don'd mind the source address of 1.1.1.1. Its just an address that is located behind "outside" interface according to the ASA routing table. (As the configurations 1.1.1.0/28 is not actually configured on the ASA)
    Share the exact "packet-tracer" command used (wihtout the public IP, notice that the output contains the public IP also) and the output of the command with us here.
    Also, have you made sure that there is no old translations active on the ASA?
    You can use this command to view those
    show xlate local 192.168.1.100
    You can clear the xlates with
    clear xlate local 192.168.1.100
    - Jouni

  • ASA code version upgrade error

    I just recently tried to upgrade the code version of a 5510 from 8.3(2) to 9.1 and got this error:
    This is an ASA image and cannot be loaded on a PIX platform.
    I was consoled into the firewall and watching it boot up, after that error it just said "rebooting..." and nothing ever happened. Can someone please shed some light on this as I have no idea why that error popped up and can't find any documentation about it. I tested the upgrade on a seperate 5510 to make sure it would work beforehand and didn't have any issues. Thanks in advance!

    The problem is that the flash storage is corrupt. I have also received this error in the past. Power cycling did absolutely nothing to help, and I was not able to get far enough to boot from ROMMON to boot to another image. It was resolved simply by processing an RMA with Cisco Systems. Out of many hundreds of Cisco devices that I have installed, I have only experienced this happening one time. It seems (based on research) more common with the ASA for some reason. I have absolutely never had this happen with an ISR, or Catalyst switch. Of course, these are all rather different devices. This problem could just be specific to the ASA itself. I had it happen with a 5505. OP had this occur on a 5510. Perhaps this should be looked in to by the ASA dev. team if it has not already been addressed.

  • ASA 5520 Version 8.2(1) Split tunnel enable Process

    Hi,
    We have configured a cisco ASA 5520 firewall as a remote VPN. Remote VPN user connected properly but VPN user disconnected form internet. So we need to configure split tunnel. Please help us how to configure split tunnel and require parameters/field. Thanks...

    Hi,
    The setup is usually pretty easy
    First you should create a Standard ACL that defines the networks which are found behind the VPN connection from the users perspective. In other words the networks that need to be tunneled.
    For example if your LAN networks was 10.0.0.0/24
    access-list SPLIT-TUNNEL standard permit 10.0.0.0 255.255.255.0
    Then you would need to configure some additional things in your VPN client connections "group-policy"
    For example
    group-policy CLIENT attributes
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value SPLIT-TUNNEL
    The above would essentially handle the Split Tunnel portion of the configurations. The "split-tunnel-policy" command specifies how the network selection for the VPN is handled. It might aswell be configured to specify Full Tunnel or to simply Exclude some networks. The "split-tunnel-network-list value" command tells the ASA the networks used in the Split Tunnel (the ACL we created)
    Hope this helps
    - Jouni

  • ASA 5545x version 9.2 and Manager 7.2(1) and ASA-CX 9.2 Telnet dropping

    On the ASA I have two service policy rules.
    The first is a Global using traffic Classification and matching Default Inspection Traffic and everything runs great.
    The second policy is a class-default and under the “ASA CX Inspection” when I “Enable ASA CX for this traffic flow” and apply I’m having dropped and freezing telnet sessions. 

    Your Ethernet0/1 is a trunk with multiple VLANs allowed but you do not have corresponding VLAN interfaces for SVIs in each of the associated subnets. If, as your routing setup indicates, you will be going via your internal gateway at 10.10.1.1 to reach the internal subnets then Eth0/1 should just be an access port.
    So your Exchange server in the 10.10.12.0/24 subnet  will talk via the internal gateway (10.10.12.1?) and thus on to the ASA inside interface at 10.10.1.2.
    I assume your "public" IPs have been changed to anonymize the output. If those are your actual addresses (10.24.56.x) then there must be additional NAT taking place upstream - that would all need to be setup properly as well.

  • ASA CSC version 6.3.1172.0 upgrade

    I have a client running 6.1.1569.2 as the software version for their CSC. Now they would like me to upgrade to the newest one. But before I do that I want to read the readme. To see what 6.3.1172.0 fixes/resolves/breaks/add's
    I cannot seem to find any documentation on this new verison.
    Does anyone know where i can find this information? HAs anyone updated to this and did it break/help things?

    The Release notes are here http://www.cisco.com/en/US/docs/security/csc/csc63/release/notes/cscrn631.html
    6.3 adds features and has improvements. Now big problem reported. There is already a .1 patch for it.
    PK

  • (Love this Forum) Making an interim version of sequences?

    I have a number of sequences that I need to see together to see how they are working. Does this sound right: Make a sequence called Tesy Master, then drag sequences into it and run it?
    Then what, trash that sequence and do a new one next time?

    Hi(Bonjour)!
    Yeah. This process is called nesting.
    BTW nesting is a great technique. Think of it like big blocks assembly that can be chained together.
    Here's some tips about nesting:
    You can hold the command key AND drag sequence A from browser to timeline B to insert clips individually, not as a whole sequence A.
    If you ALT double click on sequence A in browser, it will open in a new viewer as a long clip.
    If you insert sequence A as it from browser in timeline B, any changes in original sequence A will appear in the new one B. BUT if you set any IN or OUT point in the viewer for sequence A before inserting, changes will not be reflected in timeline B.
    Nested sequences is a great way to add a common filter like black and white, vignette, washed effect color correction, etc, to an entire program.
    Michel Boissonneault

  • Release Notes of ASA 9.1.5 Interim 12?

    Hello,
    does anyone have the Release Notes of ASA 9.1.5 Interim Release 12 (asa915-12-smp-k8.bin)?
    The release notes available for download state differences for 9.1.5-10.
    Best regards,
    Frank

    Hi,
    I don't think you would be able to get the Release Notes for 9.1.5.12 as it is an interim version.
    We don't have release notes for all the interim version.
    Check this:-
    http://www.cisco.com/c/en/us/support/security/asa-5500-series-next-generation-firewalls/products-release-notes-list.html
    Thanks and Regards,
    Vibhor Amrodia

  • Error when attempting to remove static route from ASA 5525x running version 9.0(4)

    Hello, 
    I am having difficulty in removing static routes from my ASA5525x, hoping someone here may be able to help.
    Example:
    ASA5525X/pri/act# sh route | in 192.168
    S    192.168.60.0 255.255.255.0 [1/0] via 64.57.xxx.xx, OUTSIDE
    ATLCOLO-ASA5525X/pri/act(config)# no route OUTSIDE 192.168.60.0 255.255.255.0 64.57.xxx.xx
    %No matching route to delete
    There are several which need to be removed, all 192.168.x.x/24, pointing to the Outside interface using the same address 64.57.xxx.xx

    Hi,
    I think i agree with Jon that this is probably due to RRI from the VPN configuration.
    Also , check this output:-
    show asp table routing and see if you see it in here as well.
    We also have some defects so please provide the relevant interface and routing configuration and also the ASA code version.
    Thanks and Regards,
    Vibhor Amrodia

  • Upgrade path for ASA 5.2 to 8.0

    We just bought a company and need to upgrade the ASA5520 to a version 8.0.3 on the old ASA from version 5.2, is there an interim upgrade required or can we go directly to 8.0.3? I saw documents say you have to go from 5.1 to 5.2 and 7.1 to 7.2 first but nothing about 5.2 and going to a later ASA version.

    Hi,
    I think you are referring to two images here. One is the image for the ASA itself (7.0, 7.1, 7.2 and 8.0) and the other for ASDM (5.1, 5.2, etc).
    1. Below is the release notes for 8.0 code. Depending upon what version of code you are running on the ASA, it is recommended that upgrade in steps. That is, 7.0 to 7.1, 7.1 to 7.2 and then 7.2 to 8.0.
    http://www.cisco.com/en/US/docs/security/asa/asa80/release/notes/asarn80.html
    You must upgrade or downgrade from Version 7.2.(x) to Version 8.0(2) and vice versa, because older versions of the ASA images do not recognize new ASDM images, and new ASA images do not recognize old ASDM images.
    You could leap frog and just from 7.0 to 8.0 directly and I have seen it work. Its just not recommended. Also, by doing this, you may lose per-version upgrade/downgrade capability.
    2. Below is the release notes for the various version of the ASDM (Management Software) and depending upon the version and ASA Chassis you are planning to upgrade, refer the release notes for upgrade instructions.
    http://www.cisco.com/en/US/products/ps6121/prod_release_notes_list.html
    Regards,
    Arul
    ** Please rate all helpful posts **

Maybe you are looking for