ASA ios ver 7.2 Track command not working
Hi
I have ASA 5520 with 7.2 ios. i am having 2 vpn boxes in the dmz. i used to track and sla monitor command but the static route does not get removed from the routing table and the higher AD route does not get added. below is the Sla and Track command which are running
sla monitor 1
type echo protocol ipIcmpEcho 192.168.30.3 interface Dmz1
sla monitor schedule 1 life forever start-time now
track 20 rtr 1 reachability
route Dmz1 192.168.206.0 255.255.255.0 192.168.30.3 1 track 20
route Dmz1 192.168.206.0 255.255.255.0 192.168.30.4 50
can someone tell me if i am going wrong somewhere
The configs are not attached.
Similar Messages
-
ASR 1006 with IOS 3.13.1S, NetFlow commands not working
Hi,
We have Cisco ASR1006 router with IOS asr1000rp1-advipservicesk9.03.13.01.S.154-3.S1-ext.bin, we have recently upgrade IOS from asr1000rp1-advipservicesk9.02.03.02.122-33.XNC2.bin.
After upgrading the IOS ip flow ingress and ip flow egress command is not working.
Please suggest on configuring NetFlow commands on this.
Regards
MACAlso try this link, found if you follow the URL above, and I have made some notes about configuring inbound and outbound flow monitoring :-
http://docwiki.cisco.com/wiki/Migrating_from_Traditional_to_Flexible_NetFlow#Flexible_NetFlow_Migration_in_Practice
That article was referred in these release notes but don’t follow the link in the release notes, use the link above as it seems to have moved;
http://www.cisco.com/c/en/us/td/docs/routers/asr1000/release/notes/asr1k_rn_rel_notes/asr1k_feats_important_notes_313s.html#pgfId-3455900
The syntax I have used is almost the same, except that I don’t think you can quite have the 2 options they mention in the last line;
flow exporter FlowExporter1
destination 192.168.9.101
transport udp 9996
export-protocol netflow-v5
source FastEthernet 0/1
flow monitor FlowMonitor1
record netflow ipv4 original-input
exporter FlowExporter1
cache timeout active 1
cache timeout inactive 15
interface FastEthernet 0/1
ip flow monitor FlowMonitor1 [input|output] <<< with the netflow record above only input is ok
According to the command reference I looked at when you use the ipv4 ‘netflow’ flow record with ‘original-input’, it can only monitor inbound packets and vice-versa for ‘original-output’, therefore I think you need the pair of settings as we have done.
[see here http://www.cisco.com/c/en/us/td/docs/ios/fnetflow/configuration/guide/12_2sr/fnf_12_2_sr_book/get_start_cfg_fnflow.html#wp1059480 ]
flow monitor FlowMonitor1
record netflow ipv4 original-input
flow monitor FlowMonitor2
record netflow ipv4 original-output
interface FastEthernet 0/1
ip flow monitor FlowMonitor1 input
ip flow monitor FlowMonitor2 output
Rgds
Ian -
IOS 7 flip-up audio command not working on iPhone 5
I updated to iOS7 on my iPhone 5. While many things seem to be working fine, I noticed that the music buttons (play, pause, FF, RW) on the newly-introduced flip-up menu do not work. I need to go to turn on music (touch the red icon) and play/pause/FF/RW. Is it just me that is observing this?
You must have Internet connection for Siri to work either Wi-Fi or cellular data.
-
E-commerce Sales Tracking is not working in magento (ver 1.7.0.2)
Hi,
e-commerce Sales Tracking is not working in magento for my website - [Link removed], I implemented remarketing tag (dc.js ) with it.
Please help me find out the problem.
Thanks
VimleshThis is Adobe Business Catalyast, this is not the Magento forums and that is not an Adobe product. I suggest you go try over there for help.
-
In Photoshop CC 2014 Alt + Ctrl + C ( to open for canvas size dialog box ) command not working, it is opening Internet Explorer (IE)
What version of windows are you using?
See if the Internet Explorer shortcut has that keyboard shortcut assigned to it. -
Bash commands not working after upgrade to Lion
After upgrade, many BASH commands not working. For example, such a fundamental thing as "ls".
iMac20:bin a$ ls
Launch of "ls" failed: the PowerPC architecture is no longer supported.
What does it have to do with PowerPC? My computer is 2.66 GHz Inter Core DuoLinc,
iMac20:~ a$ which ls
/sw/bin/ls
Also, I managed to look (using tcsh's ls-F command) into the contents of /usr/. Here's what I see there:
[iMac20:/bin] a% ls-F
[* csh* echo* ksh* mkdir* rcp* stty* wait4path*
bash* date* ed* launchctl* mv* rm* sync* zsh*
cat* dd* expr* link* pax* rmdir* tcsh*
chmod* df* hostname* ln* ps* sh* test*
cp* domainname* kill* ls* pwd* sleep* unlink* -
Why is my BDC_CURSOR command not working to position the cursor?
Why is my BDC_CURSOR command not working to position the cursor? Here are the details regarding my issue.
I am writing a BDC to mass delete routing material assignments using transaction CA02. I am OK to navigate through the initial screen to go to the Header screen and from here I am OK to navigate to the Material Assignments screen. But once here, I cannot get the BDC_CURSOR command to take me into the list. Here are the commands I am using. Please let me know what I may try differently.
CA02 Material Assignment - Set position <-- this resets list of materials to correct position
PERFORM bdc_dynpro USING 'SAPLCZDI' '1010'.
PERFORM bdc_field USING 'BDC_CURSOR' 'RC27X-ENTRY_ACT'.
PERFORM bdc_field USING 'BDC_OKCODE' '=ENT1'.
PERFORM bdc_field USING 'RC27X-ENTRY_ACT' c_position.
CA02 Material Assignment - Delete
PERFORM bdc_dynpro USING 'SAPLCZDI' '1010'.
PERFORM bdc_field USING 'BDC_CURSOR' 'MAPL-MATNR(01)'. <-- this is not working to set the cursor into the list
PERFORM bdc_field USING 'BDC_OKCODE' '=LOE'. " trash can
PERFORM bdc_field USING 'RC27X-ENTRY_ACT' c_position.
CA02 Material Assignment - Green Check OK
PERFORM bdc_dynpro USING 'SAPLCZDI' '1010'.
PERFORM bdc_field USING 'BDC_CURSOR' 'RC27X-ENTRY_ACT'.
PERFORM bdc_field USING 'BDC_OKCODE' '=BACK'. " check mark
PERFORM bdc_field USING 'RC27X-ENTRY_ACT' c_position.Thank you for your reply.
I had used SM35 to record. However, I was not aware of the "create program" feature. I had commented out a section from my previous post which I have now added back (latest code below). But it still did not resolve the issue.
When I execute with dismode = 'N', I get back error message "No batch input data for screen SAPLCZDI 1010".
When I execute with dismode = 'E' (only show dynpros when error), it stops at the material selection screen without placing my cursor in the list. I can then MANUALLY click to set the cursor position in the list, MANUALLY click the trashcan, it then uses my BDC command to respond to the popup asking "Do you want to delete", still leaving me at the material selection screen. I can then MANUALLY click the green check (or enter), then it continues with the BDC to go back to the previous screen, and saves. But it still will not place my cursor in the material selection list (SAPLCZDI screen 1010).
Here is code used. It is the second section of code labeled "CA02 Material Assignment - Delete" that is not working.
CA02 Material Assignment - Set position
this code functions to position the desired material to first in screen list
PERFORM bdc_dynpro USING 'SAPLCZDI' '1010'.
PERFORM bdc_field USING 'BDC_CURSOR'
'RC27X-ENTRY_ACT'.
PERFORM bdc_field USING 'BDC_OKCODE'
'=ENT1'.
PERFORM bdc_field USING 'RC27X-ENTRY_ACT'
c_position.
CA02 Material Assignment - Delete
PERFORM bdc_dynpro USING 'SAPLCZDI' '1010'.
PERFORM bdc_field USING 'BDC_CURSOR'
'MAPL-MATNR(01)'.
PERFORM bdc_field USING 'BDC_OKCODE'
'=LOE'. " trash can
PERFORM bdc_field USING 'RC27X-ENTRY_ACT'
c_position.
Acknowledge Pop-Up Screen
PERFORM bdc_dynpro USING 'SAPLSPO1' '0100'.
PERFORM bdc_field USING 'BDC_OKCODE'
'=YES'.
CA02 Material Assignment - Green Check OK
PERFORM bdc_dynpro USING 'SAPLCZDI' '1010'.
PERFORM bdc_field USING 'BDC_CURSOR'
'RC27X-ENTRY_ACT'.
PERFORM bdc_field USING 'BDC_OKCODE'
'=BACK'. " check mark
PERFORM bdc_field USING 'RC27X-ENTRY_ACT'
c_position. -
Odi os command not working with agentservice agent.
dear all,
odi os command not working with agentservice agent but with local agent it work fine.. and user is administrator.
kindly solve it
Regards
NaseerHi,
you referred to oscommand, so are you executing a .bat fille? if yes, where exactly does the .bat file reside, local machine or on network share?
Also, follow these couple of documents, they may be helpful to you.
859215.1 and 424703.1
Regards
Srikanth -
Crontab reboot command not working
Crontab reboot command not working
Greetings
I am new at this so excuse any ignorant mistakes I might be making.
I have a server (MM X.4.9) that I would like to restart every day in order to make sure no programmes are hanging etc. If a program is hanging is should force quit it. Using terminal I have entered the following command:
sudo nano /etc/crontab
Entered password
Than I entered using tab between each sequence:
15 13 1 1 * root reboot
This was a test run and it did not reboot.
Entering
cat /etc/crontab
I got:
# The periodic and atrun jobs have moved to launchd jobs
# See /System/Library/LaunchDaemons
# minute hour mday month wday who command
15 13 1 1 * root reboot
What have I done wrong?
ThanksHehe, there you are experimenting with a "reboot" cron command and you are surprised it quit so fast. You are not going to find a "graceful" solution to shutdown dialogs.
MSWord is a Java app, so it is especially important for the command to work that it doesn't get hung up on outer layers of the system. Especially stupid apps that use Java which is not well integrated. I believe Word has a 5 minute autosave, so you should be able to recover most of your document.
This reboot command should be running around 2AM, when the average webserver has minimum traffic. If you feel the need to reboot during busier times of the day, I'd suggest you look at what's causing your applications to crash. -
Illustrator Short Commands Not Working
Hi Team,
My illustrator CS6 short commands have stopped working.
Any time I try to use any CMD + Key, illustrator will not react.
This has been on going for a few months, I have tried resetting preferences but nothing has changed.
If someone could please help.
Thanks,
BrandonHi Jacob,
I have tried resetting preferences and few other options.
Anytime I press the CMD key the option at the bottom just changes from selection to direct selection, if that helps.
Should I uninstall and reinstall illustrator?
I no longer have my access key.
Thanks,
Brandon
Date: Wed, 8 Jan 2014 15:39:58 -0800
From: [email protected]
To: [email protected]
Subject: Illustrator Short Commands Not Working
Re: Illustrator Short Commands Not Working
created by Jacob Bugge in Illustrator - View the full discussion
THS,
You may try the following (you have tried/done some of them already) and see whether it helps (the following is a general list of things you may try when the issue is not in a specific file; 3) and 4) are specifically aimed at possibly corrupt preferences):
1) Close down Illy and open again;
2) Restart the computer (you may do that up to 3 times);
3) Close down Illy and press CtrlAltShift/CmdOptionShift during startup (easy but irreversible);
4) Move the folder Other options (follow the link with that name) with Illy closed (more tedious but also more thorough and reversible);
5) Look through and try out the relevant among the Other options (follow the link with that name, Item 7) is a list of usual suspects among other applications that may disturb and confuse Illy, Item 15) applies to CC, CS6, and maybe CS5);
Even more seriously, you may:
6) Uninstall, run the Cleaner Tool (if you have CS3/CS4/CS5/CS6/CC), and reinstall.
http://www.adobe.com/support/contact/cscleanertool.html
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/5994475#5994475
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/5994475#5994475
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/5994475#5994475. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Illustrator at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0. -
Motion tracking is not working for videos but works for images?
Motion tracking is not working for videos but works for images. When the videos is drop onto the tracking object the videos corner don't appear highlighted. I am working on windows 7 with version 13.1.
ivanhoeeurope
Are you within 30 days of purchase for the Premiere Elements 13? And, did you purchase as a download from Adobe? If so, you can
apply for a return/refund for 13. If you purchased elsewhere, then you would be governed by the return/refund policy of the seller.
Adobe no longer sells version 12, so you would have to find a vendor who still has it in stock and purchase it. There is no way to "downgrade"
13 to 12.
What you may want to do is to download and install the Premiere Elements 12 tryout from the following web site to verify that 12 Motion
Tracking works for you; whereas 13 cannot with regard to use of video for the Motion Tracking source media.
Adobe Photoshop Elements 12 Direct Download Adobe Photoshop Elements 12 Direct Download Links, Premiere too | ProDesignTools
Apparently this web site does not sell the tryout. It just makes it available for use.
Before I posted my reply to you I looked at Motion Tracking with video source media on both Premiere Elements 12/12.1 and 13/13.1 on the same Windows 7 64 bit computer.
If any questions or need clarification, please do not hesitate to ask.
Thank you.
ATR -
Why does default keyboard shortcut for show/hide baseline grid (opt+command+') not work?
Here's where you need to change the settings: System Preferences > Keyboard > Keyboard Shortcuts:
-
I have an Iphone 4s factory unlocked. I got At&t again and after updating to iOS 6.0 my iphone its not working propertly. I dont have the carriers option nor Im able to face time using cellular data. Any suggestions!?
Do you have an AT&T carrier file number showing? The only time you can use Facetime on AT&T cellular is if you are using one of their Shared Data plans. While they have not locked your phone, it appears their carrier file is in control of your device when you have the AT&T SIM card in there.
-
Just updated my iPad with iOS 7 and now internet does not work anymore, how to fix if???? Desperate
Try resetting your iPad:
Double click the Home button. Slide up with one finger on ALL your apps to close them.
Then, Press the Sleep/Wake button + Home button and hold 15 seconds or until you see the Apple logo.
This will reset your device without erasing data, apps or settings. -
HT1212 My phone is disabled. I just loaded IOS 7 and my password does not work.
My phone is disabled. I just loaded IOS 7 and my password does not work.
I do not understand how to remotely wipe the phone using icloud, find my phone or my apple id and password. Kindly explain step by step as I am an older individual and I am confused
Maybe you are looking for
-
I am getting an error when trying to install the current updates.
-
Accidentally deleted Fireworks CS6 in my CC suite of apps
When I did this I was deleting a bunch of old installs (CS3 and various demos since that version). I thought FW CS6 was an old demo, so I dragged it to the trash, uninstaller and all. Then when updating apps in CC, I noticed the FW update failed and
-
Automatic Reconciliation with the BSP add-on
Hello I have an issue when trying to use the BSP to externally reconcile the Bank account in the following circumstance. Incoming payment has been taken the bank adds the fund to the bank and the payment is reconciled within SBO using the BSP. A few
-
BAPI_PO_CREATE1 use of potextitem in tables can i use this to populate text
hi i nedd to know BAPI_PO_CREATE1 use of potextitem in tables can i use this to populate text at item level as my requirment is to populate the item text at item level in me23n tcode so how to use this pls suggest and how to acheive it? under me23n t
-
Search string for most wordmatches in database
Hello! I'm working on a chatbot program and I need to make a search engine in flash. I already have on searchengine that search a string (with the users inputtext in it) and compares it to phrases in a database ( a xml file in this case). But I also