ASA IPS, auto update issue
Hi,
I am having an issue with auto update on the IPS module installed the ASA.
Auto Update Statistics
lastDirectoryReadAttempt = 06:00:34 UTC Wed Feb 23 2009
= Read directory: https://198.133.219.25//cgi-bin/front.x/ida/locator/loca
tor.pl
= Error: AutoUpdate exception: Receive HTTP response failed [3,212]
lastDownloadAttempt = N/A
lastInstallAttempt = N/A
nextAttempt = 06:00:00 UTC Thu Feb 24 2009
I can see from the above that there is a HTTP response error, I have checked and there does not seem to be any other unit stopping the responses. With regards to the ASA config do I need to allow the IPS module though the ACL's or NAT statements?
Many thanks MJ
Hi
Many thanks for the respose.
Sorry I have not made any progress with this as yet: the only thing I have done is us the packet tracer, which passed I am just going to check the route of the packet once it has left the interface as it has got to be that or the URL is wrong.
Regards MJ
Similar Messages
-
WRVS4400NV2 IPS now blocking Cisco IPS Auto Update Server
Yesterday I noted that my ASA5505 AIP-SSC5 card was failing to auto update as it had been doing without issue for months. I looked in the logs and the IPS was showing an HTTP Error when attempting to update. I checked and nothing had changed in the IPS configuration. Then, on a hunch, I checked the IPS log of the WRVS4400N which is the edge router for the small business network.
The WRVS4400N IPS was blocking connections with the cisco auto update server because it detected an RPC Anomaly in the traffic. So apparently, something has changed in the cisco IPS auto update server (https://198.133.219.25//cgi-bin/front.x/ida/locator/locator.pl) response that the cisco small business router misidentifies as a threat. . .
FYI-I also posted this issue to the small business router community discussion forum.Yesterday I noted that my ASA5505 AIP-SSC5 card was failing to auto update as it had been doing without issue for months. I looked in the logs and the IPS was showing an HTTP Error when attempting to update. I checked and nothing had changed in the IPS configuration. Then, on a hunch, I checked the IPS log of the WRVS4400N which is the edge router for the small business network.
The WRVS4400N IPS was blocking connections with the cisco auto update server because it detected an RPC Anomaly in the traffic. So apparently, something has changed in the cisco IPS auto update server (https://198.133.219.25//cgi-bin/front.x/ida/locator/locator.pl) response that the cisco small business router misidentifies as a threat. . .
FYI-I also posted this issue to the small business router community discussion forum. -
Hi,
I have a couple of questions I hope people could answer:
1) What recommendations/options are available for downloading signature files to a HTTP/TFTP server prior to having the IOS IPS device pull them from the server? Is their a way to automate the HTTP/TFTP server downloading the signatures? (Cron job or such)
2) Does the signature file name change each time a new signature file is released? If it does, would I have to go back to the router to update the URL string that is configured in the ip ips auto-update section? I would hate to have to update 200 CPE devices each time a new signature file is released.
Hoping someone could answer these or help point me in the right direction to find the answer out.
regards MI found this link with answers my one question.
Cisco IOS Intrusion Prevention System (IPS)
Tuning, Deploying and Updating Cisco IOS IPS Signature Sets For Multiple-Device Deployments
http://www.cisco.com/en/US/prod/collateral/iosswrel/ps6537/ps6586/ps6634/white_paper_c11_549300.html -
The auto update is not working on the IPS. The current signature version is S502 but my IPS is S479
show statistics host output
Auto Update Statistics
lastDirectoryReadAttempt = 05:35:12 GMT-05:00 Mon Jul 26 2010
= Read directory: https://198.133.219.25//cgi-bin/front.x/ida/locator/locator.pl
= Success: No installable auto update package found on server
lastDownloadAttempt = N/A
lastInstallAttempt = N/A
nextAttempt = 05:35:00 GMT-05:00 Tue Jul 27 2010
Auxilliary Processors Installed
show version output
Application Partition:
Cisco Intrusion Prevention System, Version 6.1(1)E3
Host:
Realm Keys key1.0
Signature Definition:
Signature Update S479.0 2010-03-19
Virus Update V1.4 2007-03-02
OS Version: 2.4.30-IDS-smp-bigphys
Platform: ASA-SSM-10
Serial Number: JAF10241017
Licensed, expires: 03-Sep-2010 UTC
S479.It looks like the issue is that the IPS is running the E3 engine (6.1(1)E3). All new updates require the E4 engine, so you'll have to update the sensor to 6.2(2)E4 or 7.0(4)E4. Upgrade links and instructions can be found here:
https://supportforums.cisco.com/docs/DOC-12212 -
I am having an issue with the IPS. I have configured it for auto update and I am trying to download a new signature package. It seems to be working. However, once it comes across the package to download, it gives me this error:
evError: eventId=1232049941352795438 severity=error vendor=Cisco
originator:
hostId: xxxxips11
appName: mainApp
appInstanceId: 347
time: 2009/01/29 15:22:03 2009/01/29 10:22:03 GMT-05:00
errorMessage: name=errSystemError autoUpdate successfully selected a package () from the cisco.com locator service, however, package download failed: This package file does not have the required .pkg extension
I know that it is trying to download the correct package because I get this message prior:
evStatus: eventId=1232049941352795436 vendor=Cisco
originator:
hostId: xxxxips11
appName: mainApp
appInstanceId: 342
time: 2009/01/29 15:22:03 2009/01/29 10:22:03 GMT-05:00
autoUpgradeServerCheck:
uri: xxxxxx@//
packageFileName: IPS-sig-S378-req-E3.pkg
result: status=true
Does anyone know what this could possibly be?Upgrade IPS MC and Security Monitor to 2.2.
-
I've configured the signature auto update via the GUI and CLI but receive the same error:
evError: eventId=1210198298109812431 vendor=Cisco severity=error
originator:
hostId: LON-Sensor
appName: mainApp
appInstanceId: 341
time: Jun 06, 2008 03:00:07 UTC offset=60 timeZone=BST
errorMessage: MainApplication::downloadAndStartUpdate Error status returned with status str Found name=errSystemError
Any ideas? I've rebooted both the IPS & ASA in the hope that would resolve the problem to no avail. I have another ASA/IPS in a different site and that works ok.Hi, I got the information :)
show stat host
General Statistics
Last Change To Host Config (UTC) = 14-Jan-2009 14:38:43
Command Control Port Device = GigabitEthernet0/0
Network Statistics
= ge0_0 Link encap:Ethernet HWaddr 00:13:C4:80:C3:C1
= inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0
= UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
= RX packets:25375769 errors:0 dropped:0 overruns:0 frame:0
= TX packets:2411636 errors:0 dropped:0 overruns:0 carrier:0
= collisions:0 txqueuelen:1000
= RX bytes:2570835196 (2.3 GiB) TX bytes:657595036 (627.1 MiB)
= Base address:0xbc00 Memory:f8200000-f8220000
NTP Statistics
status = Not applicable
Memory Usage
usedBytes = 660455424
freeBytes = 372043776
totalBytes = 1032499200
CPU Statistics
Usage over last 5 seconds = 31
Usage over last minute = 40
Usage over last 5 minutes = 36
Memory Statistics
Memory usage (bytes) = 660455424
Memory free (bytes) = 372043776
Auto Update Statistics
lastDirectoryReadAttempt = 08:40:00 GMT-06:00 Wed Feb 04 2009
= Read directory: https://198.133.219.25//cgi-bin/front.x/ida/locator/locator.pl
= Error: AutoUpdate exception: HTTP connection failed [1,111]
lastDownloadAttempt = N/A
lastInstallAttempt = N/A
nextAttempt = 08:40:00 GMT-06:00 Thu Feb 05 2009
Auxilliary Processors Installed.
! Current configuration last modified Mon Jan 19 17:15:14 2009
! Version 6.2(1)
! Host:
! Realm Keys key1.0
! Signature Definition:
! Signature Update S379.0 2009-01-30
! Virus Update V1.4 2007-03-02
service interface
exit
service authentication
exit
service event-action-rules rules0
overrides deny-attacker-inline
override-item-status Enabled
risk-rating-range 90-100
exit
exit
service host
network-settings
host-ip 192.168.1.11/24,192.168.1.1
host-name sensor
telnet-option disabled
access-list 10.254.254.0/24
access-list 192.168.1.0/24
exit
time-zone-settings
offset -360
standard-time-zone-name GMT-06:00
exit
auto-upgrade
cisco-server enabled
schedule-option calendar-schedule
times-of-day 08:40:00
days-of-week monday
days-of-week tuesday
days-of-week wednesday
days-of-week thursday
exit
user-name ********
password ********
cisco-url https://198.133.219.25//cgi-bin/front.x/ida/locator/locator.pl
exit
exit
exit
service logger
exit
service network-access
exit
service notification
exit
service signature-definition sig0
signatures 9430 1
status
enabled true
exit
exit
signatures 11018 1
status
enabled true
exit
exit
signatures 12000 0
status
enabled true
exit
exit
signatures 12003 0
status
enabled false
exit
exit
signatures 12020 0
status
enabled true
exit
exit
exit
service ssh-known-hosts
exit
service trusted-certificates
exit
service web-server
exit
service anomaly-detection ad0
exit
service external-product-interface
exit
service health-monitor
memory-usage-policy
enable true
exit
exit
service analysis-engine
virtual-sensor vs0
physical-interface GigabitEthernet0/1
exit
exit -
Hi,
I have auto update enabled in my AIP SSM 10 , at the time of auto updates i have observed the following messages in Console
"Broadcast Message from IPS
Applying update IPS-sig-S766-req-E4"
It remains in this condition and then i have to do a hw-module reset to get it back again , moreover updates which were downloaded arent applied.
Kindly HelpWhen signature auto-update failures are diagnosed, look at the HTTP error codes.
IPS# show statistics host
Auto Update Statistics
lastDirectoryReadAttempt = 19:31:09 CST Thu Nov 18 2010
= Read directory: https://72.163.4.161//cgi-bin/front.x/ida/locator/locator.pl
= Error: AutoUpdate exception: HTTP connection failed [1,110] <--
lastDownloadAttempt = 19:08:10 CST Thu Nov 18 2010
lastInstallAttempt = 19:08:44 CST Thu Nov 18 2010
nextAttempt = 19:35:00 CST Thu Nov 18 2010
Message Meaning
Error: AutoUpdate exception: HTTP connection failed [1,110]
Authentication failed. Check the username and password.
status=false AutoUpdate exception: Receive HTTP response failed [3,212]
The request to the Auto Update server timed out.
Error: http error response: 400
Make sure the cisco-url setting is defaulted. If the CCO ID is greater than 32 characters in length, try a different CCO ID. This can be a limitation on the Cisco download server.
Error: AutoUpdate exception: HTTP connection failed [1,0]
Network issue prevented download or there is a potential issue with the download servers.
and also keep in mind that CCO username should not contain any special characters, for example, @ . Refer to Cisco bug ID CSCsq30139 (registered customers only) for more information. -
IPS auto-update vs manual download
Is there a delay in what's available via auto-update and updates that are available for manual download through cisco.com? I noticed today that S498 became available yesterday, but my IPS module in my ASA hasn't downloaded it automatically yet. When I do a #sh statistics host, I have a recent download attempt that says "Success: No installable auto update package found on server.
Just wondering if there is a delay between manual and auto updates or if I need to be concerned that my auto-udpates aren't working properly.
Thanks!The "lastDirectoryReadAttempt" is when the last check occurred (should match your scheduled timing). If the status is that there is no available update, that is as far as the process goes. If an update is available, the sensor should attempt to download.
The "lastDownloadAttempt" will indicate the last time an update download was found and the download was attempted.
The "lastInstallAttempt" will indicate the last time an update was downloaded and install initiated.
It does look like it checked at a point today and did not find an available update. That your outputs are UTC, I cannot correlate when the check today was run in relation to the publishing of the latest update. It may be that there is a cache engine between your sensor and Cisco, and it is indicating that there is nothing available. I would give the process another 24 hours to update.
Scott -
Hello,
I have two IPS ASA5525-IPS "module" of 5525-X Firewall.
I set the proxy connection in DNS/Proxy Settings for update the signatures, but, i receive an error above:
Auto Update Statistics
lastDirectoryReadAttempt = 11:03:09 GMT-03:00 Wed Jan 09 2013
= Read directory: https://198.133.219.25//cgi-bin/front.x/ida/locator/locator.pl
= Error: AutoUpdate exception: HTTP connection failed [1,110]
lastDownloadAttempt = N/A
lastInstallAttempt = N/A
nextAttempt = 11:00:00 GMT-03:00 Thu Jan 10 2013
Auxilliary Processors Installed
Testing the connection i can see the packet direct in my firewall, and not passing over the proxy, i need the IPS use the proxy to update signatures.
The configuration looks okay for me.
Any sugestions?
Tks a lot.Hi,
This enhancement to use proxy server for updates would be available in future release. (CSCsv89560)
Regards,
Sawan Gupta -
Hello, Customers having IPS 4215 version 6.0(5)E3 are having their sensor crashing following auto update from an FTP server.
The web interface is no more accessible and the analysis engine stopped( I've attached the show tech-support)
The problem happened with different signatures S383 and S384, please adviseHaving a 4215 sensor crash on a signature update is a very common event.
The 4215 sensors only have 512 MB or RAM (most sensors have 1 or 2 GB), this has caused many problems during the update process.
You can try rebooting the sensor several times, if that doesnt bring it back to life, you can try resetting the signature policy back to default, if that doesn't help you'll need to open a TAC case to modify some of the signature build time memory parmeters. -
IOS IPS auto-update without CSM
Hi,
We have 400 x 1811 router on which we need to update the IPS signature definition and custom signature.
What is the best way to do it withou running CSM ?
According to Cisco documentation, we need to add the auto-update command with an .XML extention. But when we load a .pkg in a router, the output is 4 different files. Unfortunalty we can auto-update only one file. Which one to I need to load on our TFTP server ?
All the exemples of Cisco are using one single XML file.
Does a single file with the signature defenition, category, default and type exist ?
Since all our router have the same IPS config, I tought I could use one router at the central office with the configuration we want. And by someway asking the remote routers to auto-update their XML file on that router on which I would have activated a TFTP server.
Anyone ever had to upgrade a lot of router IOS IPS signature?This can now be done in the 15.1T branch using cisco.com to download the update directly, see :
http://www.cisco.com/en/US/docs/ios/15_1/release/notes/151TNEWF.html#wp1040750
http://www.cisco.com/en/US/docs/ios/sec_data_plane/configuration/guide/sec_ips5_sig_fs_ue.html#wp1137583 -
IPS Auto update - http error response
Hi
I am having trouble doing auto signature update on my AIP-SSM. This is what i am getting on #show statistics host
Auto Update Statistics
lastDirectoryReadAttempt = 11:00:08 GMT+08:00 Mon Jul 06 2009
= Read directory: https://198.133.219.25//cgi-bin/front.x/ida/locator/locator.pl
= Error: http error response: 500
lastDownloadAttempt = N/A
lastInstallAttempt = N/A
nextAttempt = 12:00:00 GMT+08:00 Mon Jul 06 2009
Fyi..my CCO credentials are perfectly fine, as i am able to download signature files manually from Cisco Download site.
Please adviseIf you are looking at the Auto Update Statistics in your sh tech, you can see a "http error response: 500" This is an internal web server error. Are you sure there is nothing between the AIP-SSM and the internet besides the ASA? Maybe there is an embedded web server like Barracuda? Do you know if your ISP is providing proxy services for you?
-
Hi! experts
I using AIP-SSM-10 module on ASA 5540
But it is not working auto update signature.
So I `m going to attach " show statistics host" result.
Can you tell me some help?
Thanks in advance
Auto Update Statistics
lastDirectoryReadAttempt = 07:34:50 UTC Tue Oct 20 2009
= Read directory: https://198.133.219.25/cgi-bin/ida/locator/locator.pl
= Error: AutoUpdate exception: HTTP connection failed [1,0]
lastDownloadAttempt = N/A
lastInstallAttempt = N/A
nextAttempt = 04:00:00 UTC Wed Oct 21 2009It is clear that mgmt ifaces are able to connect to the Internet but if they may connect to inet via proxy you must configure proxy-server.
-
ASA 5520 auto-update polling error
Hi,
the polling service for auto-update on my ASA 5520 is not working properly. Does anyone have ideas which could be the reason for this?
Platform: ASA 5520
Version: 8.4(2)
Config:
auto-update device-id hostname
auto-update poll-at thursday 5:00 randomize 3 3
auto-update server https://*@X.X.X.X/autoupdate/AutoUpdateServlet
Output of sh auto-update:
Server: https://X.X.X.X/autoupdate/AutoUpdateServlet
Poll thursday randomly between 5:00 and 5:03, retry count: 3, retry period: 5 minutes
Timeout: none
Device ID: host name [dontletthemin]
Under normal circumstances i would expect additional lines from the sh auto-update command like:
Next poll in 4.93 minutes
Last poll: 11:36:46 PST Tue Nov 13 2012
But this output does not appear. I've searced the bug-Toolkit but did not found a entry which could explain this behaviour.Hi
Many thanks for the respose.
Sorry I have not made any progress with this as yet: the only thing I have done is us the packet tracer, which passed I am just going to check the route of the packet once it has left the interface as it has got to be that or the URL is wrong.
Regards MJ -
Manual vs. auto update issues....
I had been using "manual update" when syncing my pod to iTunes. I have an external HD and, after adding music to iPod, would just move added music into the external's folder as well. My friend talked me into switching to "auto update"...said it was easier. Well, I tried it last night. Had to wait 4 hours for music to be recopied from HD to pod (why would ALL my music have to be updated? It's already on the iPod), then after that I unplugged pod from Mac to make sure music was updated. It was. Then I adjusted volume settings to music on HD and synched pod back to Mac. It updated.....and I had to wait another 4 hours for music (with new volume settings) to be updated back to my pod! Crap. I'm through with this auto update thing. Don't want to worry about having to wait 4 hours ever time I sync my pod to my computer. Any thoughts?
I have an external HD and, after adding music to iPod, would just move added music into the external's folder as well.
I'm confused.
You add music to iTunes, sync the iPod and then move the music? Sounds like you are not wanting to fill your internal hard drive.
Why not simply change the location of the iTunes library to your external hard drive? Then you simply add the songs to iTunes and your done.
Read this -> iTunes: Moving your iTunes Music folder
Then I adjusted volume settings to music on HD and synched pod back to Mac.
When you change your music files, it will reload the changed music files back to the iPod.
When automatically syncing, it shouldn't reload everything everytime.
It will load new files added to iTunes since the last iPod update. It will reload any files that have been changed (as above.) It sync some of the info (last played, ratings, etc) but this should only take a few seconds.
Don't know why it's taking 4 hours either.
Try changing the library location and see how long it takes.
Maybe you are looking for
-
T3 doesn't read photos in SD card
Hi, I just inherited a Tungsten T3 and was able to get a 2G SD card for it. I copied some of my photos in jpg into the card using a card reader/writer but when I tried to open it in my palm it doesn't show the pics. Do I need a photo viewer? Please h
-
Newbie glad to learn of forum! ThinkVantage Update problems
I'm thrilled to learn of this forum. Last year I bought my 4th T-series, a T61 15" wide-screen with WinXP (6459-CTO). Can it be that the new BIOS (2.09-1.08) or the Power Manager (1.22) updates I just downloaded and installed will really solve
-
Could anyone provide an easy ADF tutorial to go through from end to end
Could anyone provide an easy ADF tutorial to go through from end to end retrieving a table with parameter and display result as a table on web page. would like to learn EO, VO, AM page generation with this easy example. Thanks
-
Link for sales document type and PO/delivery number
Hi guys, I have a PO number(EKPO-EBELN) and the delivery number for STO(LIKP-VBELN), how am i going to link this 2 to get the SALES document type(AUART)? thanks a lot!
-
Photo Booth closes when I try to record a video.
I got my 13 inch Macbook Pro less than a month ago and I've never managed to record a video longer than 9 seconds using Photo Booth. Every time I start recording, I get to about 10 seconds and it closes, showing the "Photo Booth quit unexpectedly" er