ASA5505 Network Configuration with new controlled WLAN

Do sho Version on the ASA it will tell you the inside hosts limit.
To upgrade to unlimited hosts is not very expensive.
https://www.cdw.com/shop/products/Cisco-ASA-5505-Software-license/1650156.aspx
However, It doesn't really support multiple ISPs in load balancing. You would need a security plus license for active/standby failover.

Hi!You guys are my last hope before we would have to spend some serious money on IT-consulting...We are a medium-sized electronics store placed in Sweden. Our network-setup has been an ASA5505, a 16-port swich, and a NetGear home wirless router. This setup has been far from perfect, but has worked okay.Due to the fact that pretty much every electronic gadget needs a wireless network to work, the number of clients has gone through the roof. We have 5 workstations, 3 printers, and then 6 network speakers, 20 phones, 10 computers needing network for demos.This issue was intended to be solved by investing some money into a EnGenius Neutron controlled wifi. So a FP5912 and two EWS320 AP:s was bought. The wifi is superb, but it had some issues with DHCP when we disconnected the old NetGear router... It turnes out that when we disconnect the...
This topic first appeared in the Spiceworks Community

Similar Messages

Configurations with database control

I want to do configurations with database control but when i give servername like
http://pluto:1178
i am getting error that page cannot be displayed
$ more portlist.ini
iSQL*Plus HTTP port number =5570
Enterprise Manager Console HTTP Port (test) = 1178
Enterprise Manager Agent Port (test) = 3978

Thanks its working but its not showing the options like
Home
Performance Administration Maintenance
only startup and recovery options are there
Please let me know how to enable b] Performance Administration Maintenance

Best wireless network configuration with my hardware

I have a rather large property and over the last year or so I have acquired the following hardware. Up until now I have been extending my network wirelessly to get through coverage. However with the recent addition of a Time Capsule and the addition of AT&T U-Verse, I decided it was time optimize my network configuration
The Hardware:
• 1 AT&T Residential Gateway (With WiFi)
• 1 Airport time Capsule
• 2 Airport Extreme 802.11n (Gigabit Ethernet)
• 1 Airport Extreme 802.11n (Fast Ethernet)
• 1 Airport Express 802.11n (used mostly for printers)
The Computers:
• Mac Pro 8 core 2.8Ghz
• Mac Mini Core Duo 1.83Ghz
• Macbook Air Core 2 Duo 1.8 Ghz
• Lenovo T60p (with 802.11n)
• Ipod Touch
The slowest system is the Mac Mini with it's 802.11g however it is close enough to the TC / Residential gateway to wire into the network. All the other systems need to take advantage of the Wifi and have the ability to use the 802.11n speed. I'm not too worried about the ipod touch...
So I know I am reaching a point of diminished returns by constantly extending my wireless connection. Now, would it be beneficial to set the TC as kind of my main Wif access point and use eithernet to connect my Airport Extremes to extend my network?
I have the built in 802.11g of my AT&T RG disabled right now. I could create a 2nd network to allow the connection of my mini and iPog touch. but for the most part i would prefer to leave it disabled.
One thing to take into consideration. Due to the nature of AT&T U-Verse and the connection from the AT&T RG and the TC/AP Extreme bust be in bridge mode giving DHCP control to the AT&T RG.
Whew. Any thoughts?
Message was edited by: Vermifuge

Ethernet as many routers as possible. Place secondary routers in bridge mode. Separate the N devices to a router (TC) from N+B/G devices should go to the secondary routers. Once done set wireless to create their own network. All N computers to N router ie TC and the remainder to which ever secondary router you prefer.

Question on how networking works with new Macbook Pro

Hi,
I have a question about how networking works with my new Macbook Pro. This is my first laptop so am new to mobile computing. I am about to configure it to replace my desktop which uses a wired DSL connection. Once I have my Macbook Pro configured to run off the DSL modem, what happens when I take this computer to a location that has ethernet? Will just plugging in the ethernet cable be enough to get on line? Or is there further configuration work that needs to be done?
I used a Windows laptop from work and all I had to do was plug it in to a hotel ethernet cable to get on line. However, this laptop was never configured to run on my DSL network so I am not certain if that makes things more complicated.
Thanks for your help!

Hi
Your MacBook Pro should just work when plugged into an ethernet connection.
Just check something, Open Network Preferences, you can select it from the Airport icon in the menu bar.
In the left-hand pane click on Ethernet and just check that it is set to configure using DHCP in the right-hand pane, that's it.
So when you plug in the ethernet cable it will ask the router for an IP address and off you go.
I assume that any system you plug into will use DHCP rather than static IP addresses. If it is a static IP address, you will need to manually configure the ethernet settings by inputting the IP address and subnet mask info plus DNS servers.
Usually it is done with DHCP and you don't have to do a thing and likewise your home DSL is DHCP?
If not then you will have to change your settings, make a 'Hotel' setting which you can use when in hotels and keep your 'Home' set-up for when you are at home. In the pull down menu select Edit Locations to add new ones.
Phil
Message was edited by: Philip Tyler

Network library with parental controls?

I have a network location with our iTunes library. There are 2 PCs with 3 iTouches that use this library location. The problem is that one of the devices is for a 12 year old and I want to restrict that user from seeing content that is already in the library. Parental controls does not limit this content. Seems to only prevent adding 'New' content.
Any thoughts?
Ernst.

..."I've allowed all Utilities, Applications, etc and no matter what, as soon as I turn on the "only allowed selected programs" option, it won't work."...
I'm not sure, but it is possible that allowing / disallowing based on the pre-defined categories may not work because the software that Wacom uses on my system is in an atypical location, and has an atypical structure - it actually has one application contained inside another. It may be necessary to approve the apps explicitly.
Perhaps try either:
i) Opening "/Library" > "Application Support" > "Tablet" and explicitly dragging any apps present there into the "Parental Controls" pref pane in the panel where the programmes are listed. On my system, the app is called "PenTabletDriver.app"...
or
ii) Logging in to the managed account (with application restrictions in place), and trying to launch the "PenTabletDriver.app" programme. If this generates the "application is not allowed" message, it should be possible to "always allow" with "admin" authentication to white-list it at that stage...

Older airport extreme base station as a network extender with new time capsule

I just bought a new time capsule (802.11ac). Can my older airport extreme base station (model A1143) be used as a network extender with it?

Yes, although it maybe disappointing..
There are two kinds of extending.. wireless repeater type which is poorest as it has to transfer all packets in two steps instead of one.. hence will halve the speed.
Or using ethernet to the old extreme and set it in bridge.. You can then setup roaming network... this is much better.. but getting ethernet to the right place could be messy or expensive or both.
http://support.apple.com/kb/HT4260
wireless extend doco.. mind all of this is out of date.. the basics are correct.. the methods via the airport utility may be obsolete.
http://support.apple.com/kb/HT4145
Documentation has rather lagged lately.

Optimal configuration with new set up.

I'm getting into my own OS X Server shortly as I was assisting on an already preconfigured set up assisting with fixing remote systems and those typical types of things.
So I was hoping to get advice on setting up the OSX Server that would benefit me.
I was thinking of getting the Mac Mini Server to use with Two 13" MBPs, 1 27" iMac i7 and a 13" MacBook.
Mini Server will obviously have OSX Server & Apple Remote desktop (which will also have another copy of ARD on one of the 13" MBP).
The 27" iMac, 2x13" MBP & 13" MB will be clients of the Mini Server to distribute packages, software and disk images/installs...etc.
Optimally i dont have domain or nameserver to utilize with the server and am just using a home network setup with a Time Capsule as the router and a Linksys modem.
So during set up im not sure if i need alot of the Directory services, nameservers and if or how to set up the email side of things if my main domain is on a shared hosting service elsewhere.
aside from that there are 2x PPC PowerMac G5's that are in a separate state I need to manage as well and was hoping it was possible to manage them from my out of state location and SL Server?
thanks!

You need DNS services running on the LAN. Get that working first.
Then get OD going.
Then the rest of the stack; see the set-up and operational documentation.
While you're working on that, get yourself a server-grade firewall with VPN server capabilities; either a repurposed x86 box with a pair of network controllers or an embedded dual-NIC x86 box (running M0n0wall, Smoothwall or pfSense, etc), or a commercial server-grade firewall product option. That's your path in here, your firewall, your NAT, and the rest of your web-facing router. That (via VPN) is how you'll remote manage, reboot and operate the network.

Can't get secure wlan to work with new guest wlan

Dear Support,
I'm having a nightmare! where I can seem to get either one wlan to work or the other but not both together.
I posted previously and reconfigured as per the suggestion, however the problem I get is that the secure wlan client associates, then de-associates after roughly 30 seconds with both a guest (no security) and secure (eap using ms ias as radius server)
my previous post is;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Security%20and%20Network%20Management&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddcfe12
and the log shows the following, obviously the client is set to connect automatically.
*Mar 1 00:04:35.105: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:04:51.391: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 000e.35f8
.5d13 Associated KEY_MGMT[NONE]
*Mar 1 00:04:51.506: %DOT11-4-MAXRETRIES: Packet to client 000e.35f8.5d13 reach
ed max retries, removing the client
*Mar 1 00:04:51.506: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 000e.35f8.5d13 Reason: Previous authentication no longer valid
*Mar 1 00:05:15.176: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:05:32.703: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:05:58.780: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:06:16.141: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:06:40.759: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:06:58.145: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:07:00.560: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:07:18.020: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:07:43.902: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:08:01.254: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:08:16.172: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:08:16.737: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:08:37.397: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:08:54.732: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:08:57.193: %DOT11-4-MAXRETRIES: Packet to client 0013.cefd.48ca reach
ed max retries, removing the client
Thanks in advance for your assistance.
Any prompt reply will be greatfully received. I also rate responses.
Thanks again, regards, Adrian

Hi Ben,
Please find attached AP config, I can access the switch at the moment, but the config is fairly basic, trunk port with two vlans and vlan 1 as the native.
here's the ap config.
AP-CDC#2#sh startup-config
Using 2989 out of 32768 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP-CDC#2
enable secret 5 $1$LQ1O$NKYZoYAeiahKw0805kLHg0
clock timezone GMT 0
clock summer-time BST recurring last Sun Mar 1:00 last Sun Oct 1:00
ip subnet-zero
ip domain name wlan.internal
aaa new-model
aaa group server radius rad_eap
server 10.10.10.2 auth-port 1645 acct-port 1646
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
dot11 vlan-name dmz vlan 2
dot11 ssid Secure
vlan 1
authentication open eap eap_methods
authentication network-eap eap_methods
dot11 ssid Guest
vlan 2
authentication open
guest-mode
username Cisco password 7 062506324F41
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode wep mandatory
ssid Secure
ssid Guest
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0
54.0
no preamble-short
channel 2412
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
bridge-group 2 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
hold-queue 160 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
interface BVI1
ip address 10.10.10.49 255.255.255.0
no ip route-cache
ip default-gateway 10.10.10.253
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server attribute 32 include-in-access-req format %h
radius-server host 10.10.10.2 auth-port 1645 acct-port 1646 key 7 xyz
radius-server vsa send accounting
control-plane
bridge 1 route ip
line con 0
line vty 0 4
end
AP-CDC#2#
Thanks again, regards, Adrian

Home networking problem with new WRH54G

I just bought a new WRH54G to replace my old BEFW11S4v2 which was experiencing drop outs. I have a simple network with two PCs wired to the router sharing a cable modem Internet connection. The PCs are both running XP. With the new router the PCs can each access the Internet but don't seem to be able to see each other on the LAN. I stick in the old router and the PCs see each other and share files. I put in the new router and I get a message saying I don't have sufficient permissions to access other PCs. I swap the routers - works fine with the old, doesn't work with the new. I have run the XP Home Networking Wizard repeatedly but the results don't change. Have I missed a configuration parameter on the new router? I tried Online Chat but the guy had me run the Wizard again and then he disappeared.

Thanks for the suggestion - that's what the Online Chat person suggested last night. Remember, I described that everything works fine with my old router (BEFW11S4) (except for the continual disconnects). File and printer sharing is turned on and configured correctly on the PCs. It's only when I replace the old router with the new router (WRH54G) that the two PCs can no longer see each other. Linksys experts keep telling me to turn on file sharing - but it's been on and working for years. There's something about replacing the old router with the new router.
Anyway, I've located the problem in general terms. I recently installed Norton 360 on both computers. Norton 360 contains a firewall. When I turn off this firewall everything works. It's my problem and not Linksys'. I had checked the Microsoft firewall but didn't realize that Norton 360 also had a firewall. I don't know why the old router works - I've got to check on that. Maybe this experience will help somebody else.

Home Network Woes With New E2500

I replaced an EA1000 Wi-Fi router with a E2500, and my internet is faster, so that is a good thing. What's not-so-good is that my computers don't see each other on the network like they did before. I have 2 laptops running Windows 7 and a tablet running Windows 8.1. My main Win7 laptop does not see either of the other 2 PCs; The 2nd Win7 laptop may or may not see the other 2; and my Win8 tablet sees only the main Win7 laptop. I've gone through everything in all 3 PCs as far as Network and Sharing Center Settings. I've tried different security settings in the router setup. I would really like all 3 PCs to see each other like they did on the old router. Any suggestions on where to look, and what to look for?

Guest network is off. Both PCs that are here (1 is on a road trip) are connected to the 5 GHz band.
Both are set for Automatic IP Address.
To add to the mystery, my Dell tablet sees itself AND my Dell latop on the network, and can access files on the laptop, while the laptop itself does not even recognize itself as being on the network, i.e. when I click on network in Windows Explorer, nothing shows up. I would immediately suspect the Dell laptop as being the issue, since it doesn't even see itself on the network, except for that little fact that I can put the old router back online and each computer will see the others and they play happily together. This wackiness only happens on the new router.
Any other ideas? (and I do appreciate your help!)

Networking issue with new Macbook - cannot get IP address from DHCP router

Hello all, I've seen this problem posted a few times and been having the same problem with my new aluminum MacBook. Here's the story:
When connecting to my network at home, I get the message "Airport has a self-assigned IP and may not be able to connect to the internet." I've been able to connect a few times, but anytime it sleeps or I shut down I have the same problem. When I'm out and about, it has no problem connecting to other networks.
On the network in which I cannot connect, there are 2 other macs and two PCs that do NOT have any problem connecting. Macs are all running 10.5.5.
Router in a 2Wire and uses DHCP. ISP is AT&T.
I've tried rebooting the router, manually assigned an IP address, restarting, updating software. Nothing seems to work.
Does anyone have any other suggestions? This is kinda making me crazy.

I've also tried:
1) Creating a new location in network prefs.
2) Zapping PRAM
3) rebooting router many time.
4) putting a $ in front of the hex password
5) deleting all of the plists that I've seen recommended.
6) Starting in safe mode
7) Renewing IP
8) Shutting off firewall

TS1398 network problem with new upgrate

I never had any problems with my I Phone 4s until I upgraded to the new IOS6. I want to go into my banking accounts like I always did but it constantly says " Safari cannot open the page because it could not establish a secure connection to the server” How do I fix this problem?

Which do I check in the sharing? I tried some and it doesn't seem to work (this is on the leopard). What I am trying to do is take my iTunes file from the PC and share it so I can reload the music on the new mac.

Cannot get a home network functioning with new bth...

As a relatively new BT infinity customer I simply cannot get a home network up and running...
I have one PC which is hard-wired into the router and two laptops, all running windows 7. I have discovered from this forum that BThomehubs don't like Windows own homegroup utility so I need to ensure that all devices are on the same workgroup. OK, done.
Every sharing option is checked and even my printer properties are slected to share all. The printer is wired via USB into the main PC. I can 'see' my laptops from the PC and vice versa through windoes explorer but can only access the laptops from the PC, not the other way around which is a pain for transferring files (one of the key reasons for haveing the network in the first place!)
My printer is an Epson all in one PX650 which worked quite happily when I was a Sky Boradband customer from all devices. Now I can't even see it or seemingly add it to the network... in fact I'm not even sure I have a network in the truest sense. This is too hard BT when your competitors made it so simple.
Any thoughts will be much appreciated...

mtsue wrote:
but I cannot get a home page on the iPad.
Not sure what you mean by that. If you mean set a Starting page for Safari, then you can't. Safari will open up on the last page you browsed. If you close all tabs before exiting, it will jsut open to the gray screen. From there you can search using the google search at the top left of the address bar, or simply enter an address in the address bar.
mtsue wrote:
I also cannot get my serial number to contact support.
This can be easily obtained by flipping the iPad over and looking at the fine text at the bottom of the backside.
The Serial number is printed there.
Alternatively going into Settings->Geneal->About will have the serial number in the list of things about the iPad.
If you are finding it difficult to navigate around the iPad, perhaps setting up an appointment at the Genius Bar of your local Apple Store may be usefull. As they have Usage classes you can take.

Network issue with new iphone ios 6.1.2 - South Africa

I downloaded the new Iphone ios 6.1.2, since then I loose cell signal permanetly every hour and the only way to restore it is to switch the phone off and on - anyone experiencing the same problem?
can I not role back a version. or is there another way to maybe resolve?

iOS 6 requires iTunes 10.7 or later which requires OS X 10.6.8 or later...
https://discussions.apple.com/message/19685280?tstart=0#19685280?tstart=0

Ghost Ethernet Adaptor (en2) appeared in all network configurations!

Since a few minutes, for no related reason I can imagine,
I find in all my network configurations a new Network Port:
Ethernet Adaptor (en2)
Worse than this, in all the configurations I have not
recently modified, I found that this new ghost interface
is "On".
I looked at what may have happened at the Unix level to
discover that I have a new interface named en2 which has
an Ethernet address that start like the one of my internet
Ethernet card, but which is different.
Where is this ghost "Ethernet Adaptor" coming from?
dan

BDAqua wrote:
While it's usually 3rd Party stuff that installs/reserves virtual/additional enX cadapters, I suppose that the OS might if something is wrong or tied up when trying to use/initialize the existing ones!
IIRC, that info is stored in...
/Library/Preferences/SystemConfiguration/NetworkInterfaces.plist
But these may also affect making a new plist if you ditch that one...
It was modified on:<pre>
# esther:...mConfiguration % ls -ld NetworkInterfaces.plist
-rw-r--r-- 1 root wheel 2314 Aug 17 15:46 NetworkInterfaces.plist
# esther:...mConfiguration % </pre>
This date correspond exactly to the instant I used
the Bluetooth System Preferences to define a new
mobile phone (Sony Ericsson K320i).
But there was no Ethernet involved at any time in this
configuration.
This property list does contain a complete en2
interface description (sorry I can't quote the
content of a property list file in this web interface).
dan

ASA5505 Network Configuration with new controlled WLAN

Similar Messages

Maybe you are looking for