ASA5520 v7.2 - How disable VPN traffic?

Hi to all,
I have an ASA5520 with v7.2. I have read in the command reference that, by default, the security appliance allows VPN traffic to terminate on a security appliance interface. And here is my question:
How can I disable that to filter the VPN traffic with my own access-list?
Regards, Fernando.

Hi Shadi,
Thanks for your answer but it is not correct. If you go to "Usage Guidelines" of "sysopt connection permit-vpn" you can read:
"You can require an interface access list to apply to the local IP addresses by entering the no sysopt connection permit-vpn command. See the the access-list and access-group commands to create an access list and apply it to an interface. IMPORTANT!!! --> The access list applies to the local IP address, and not to the original client IP address used before the VPN packet was decrypted."
So that if I disabled "sysopt connection permit-vpn" I will be able to filter the local IP assigned by the vpn_pool but not the real public IP of the client.
Regards, Fernando.

Similar Messages

Server 2003 routing and remote access not passing VPN traffic

I've inherited a network that has two IP scopes that are routed through a Windows 2003 server with Routing and Remote Access. I can ping both sides (we'll call them HQ and Plant) internally. My firewall has an IP from the HQ IP scope and when
I connect via VPN, I can see all the devices on the HQ network including the network card that is in the routing server for that "side". However, if I'm connected via VPN, I cannot get to any of the IPs on the Plant side, not even the card
in the routing server. The buck stops on the server.
I should mention, that the firewall assigns IP addresses that are on the HQ scope, so all VPN connections will have an address from that side.
I'm lost on how to get this set up so my VPN traffic coming in from the HQ side can be routed to the Plant devices.

Hi,
To be honest, your statement confused me a bit.
VPN is used for external client get access to internal resource. When we setup VPN server, we usually have two NICs. We need choose a NIC that will be used when client initiate
a connection request. I prefer to call it external NIC card. The internal one will work as DHCP relay agent. So this is a single way connection. You cannot dial from internal to external.
If I misunderstood you, please elaborate what you are trying to do.
Hope this helps.

Packet Capture for VPN traffic

Hi Team,
Please help me to set ACL and capture for Remote Access VPN traffic.
Requirement is to see how much traffic is flowing from that Source IP.
Source : Remote Access VPN IP(Tunneled) 10.10.10.10
Destination : any
This is what I did which is not working
access-list VPN extended permit tcp host 10.10.10.10 any
capture CAP_VPN type raw-data access-list VPN interface OUTSIDE

Hello,
If you set up the capture with that access list, you are filtering just TCP traffic, therefore you won't be able to see UDP or ICMP traffic too, I would recommend you using the same ACL, though using IP:
access-list VPN extended permit ip host 10.10.10.10 any
Capture CAP_VPN access-list VPN interface outside
Then with:
show capture CAP_VPN
You will be able to see the packet capture on the ASA, though you can export the capture to a packet sniffer as follow:
https://<ip address of asa>/capture/<capname>/pcap capname-->CAP
For further details of captures you can find it on this link
Let me know if you could get the information you were trying to reach.
Please don´t forget to rate and mark as correct the helpful Post!
David Castro,
Regards,

Redirecting VPN traffic to WCCP

I need to be able to redirect my vpn traffic to the wccp on my network. I have read articles about this but cant really find any configuration examples or solid solutions. I read that forcing the VPN traffic to the inside interface will accomplish this, but how is this done? Are they talking about NATing the VPN traffic to the inside interface then re-NATing back out to the internet?

Have you clear the VPN tunnel down after you added the new subnet DMZ to the crypto ACL? and I also assume that the remote end has added the same mirror image ACL for their crypto ACL?
Lastly, I also assume that you have configured the NAT exemption on DMZ interface, and perform "clear xlate" after the config?

How to route traffic across subnets when one NIC is a hyper-V virtual switch?

Having a bit of a problem with a hyper-V environment which does not seem to route network traffic on two different subnets between each other.
If it were a purely physical server with two NICs and a gateway set traffic would automatically be forwarded between the two different subnets.
However when one of those NICs is a hyper-V virtual switch this simple routing no-longer seems to work and no traffic gets forwarded between subnets?
Situation is:
Hyper-V server with two NICs
NIC 1 = 192.168.0/24 - main Internal company network.
NIC 2 (hyper-V virtual switch.) = 192.168.1/24 - connects to ADSL internet router
Virtualized Domain Controller.
One or two virtualiszed NICs as necessary
How then does traffic get routed between these two subnets? If RRAS has to be configured to do this where is the best place to do it, on the hyper-V host or on the virtualized domain controller?
Thanks,

Hi ,
You can create an internal virtual switch and configure an IP for it (I assume it is 192.168.1.2/24) .
After you enable RRAS in hyper-v host there will be two gateways for different subnets .
" NIC 2 (hyper-V virtual switch.) = 192.168.1/24 - connects to ADSL internet router "
The problem is here ,if these VMs need to access internet .
So , these VMs can not configure their gateway same as the IP of internal virtual switch , you may set VM's gateway as the ADSL internet router's IP meanwhile add a static route entry for every VM .
Please refer to the Syntax :
route add -p 192.168.0.0 mask 255.255.255.0 192.168.1.2
Hope this helps
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Plz help. How disable caching SQLJ statement on WebLogic server 10.3?

Plz help.
How disable caching statement by SQLJ on WebLogic server?
what the actual problem:
1. create or replace view vtest as select object_name from dba_objects where rownum<200
2. test.sqlj
  #sql dx testIterator = {
     select object_name from vtest
   int cnt=0;
   while( testIterator.next() ){
     cnt++;
   System.out.println("Count: "+cnt);
3. Restart WebLogic and deploy project
4. Run test on server, in log file
"*Count: 199*"
5. create or replace view vtest as select object_name from dba_objects where rownum<10
6. Run test on server, in log file
"*Count: 199*"
7. Restart WebLogic
8. Run test on server, in log file
"*Count: 9*"

Hi bud,
Have you tried using WLST for what you are trying to achieve?
Please take a look at the following links:
http://docs.oracle.com/cd/E11035_01/wls100/config_scripting/domains.html
http://docs.oracle.com/cd/E13222_01/wls/docs91/config_scripting/domains.html
http://docs.oracle.com/cd/E13179_01/common/docs21/interm/config.html
Hope this helps.
Thanks,
Cris

How to print traffic lights in ALV reports

hi how to print traffic lights on selection screen in alv reports

HI,
check below code
TYPE-POOLS : icon.
types: BEGIN OF ty_display,
        status     TYPE icon-id,
        bukrs      TYPE bseg-bukrs,
        gjahr      TYPE bseg-gjahr,
        monat      TYPE monat,
        work_order TYPE z_work_order,
        glaccount TYPE saknr,
        message    TYPE string,
      END OF ty_display.
data : it_display     TYPE TABLE OF ty_display,
         wa_display TYPE ty_display.
WRITE icon_led_green AS ICON TO wa_display-status.
        wa_display-gjahr = p_year.
        wa_display-bukrs = p_cc.
        wa_display-monat = p_period.
        wa_display-work_order = v_aufnr.
        wa_display-glaccount = wa_bseg-hkont.
    APPEND wa_display TO it_display.
WRITE icon_led_red AS ICON TO wa_display-status.
          wa_display-gjahr      = p_year.
          wa_display-bukrs      = p_cc.
          wa_display-monat      = p_period.
          wa_display-work_order = v_aufnr.
          wa_display-glaccount = wa_bseg-hkont.
          wa_display-message    = text-010.
          APPEND wa_display TO it_display.
change the icon color based on your requirement and append it to the internal table which you have to display in ALV.
reward points if it is helpful.
Regards,
Srilatha

How to use traffic lights concept in alv in webdynpro abap

Hai ,
How to use traffic lights concept for alv in webdynpro abap. If possible give me some code.

Hi Ravi,
You can create ICON to get traffic light.
Go through this step by step.. in this example
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/1190424a-0801-0010-84b5-ef03fd2d33d9?quicklink=index&overridelayout=true
Please go through this...
Re: Display ICON in the ALV table column
Re: Image in ALV
cheers,
Kris.

How many vpn can be used simultaneously in Azure?

I need to add multiple locations to my azure platform approximately 90 branches , I need to know if I should set up a vpn for each branch , or as I should. thank you very much .
I am from Colombia , if they can write in Spanish would be better

Hi,
It seems that you have asked this question before:
https://social.msdn.microsoft.com/Forums/azure/en-US/c533ff85-c155-4a19-8156-67901da66ee4/how-many-vpn-can-be-used-simultaneously-in-azure?forum=WAVirtualMachinesVirtualNetwork#c533ff85-c155-4a19-8156-67901da66ee4
Based on my experience, the maximum limitation for virtual networks and local networks is 100 per subscription and the limitation for local network
sites is 10 per virtual network in Azure. If you connect each on-premise branch with an Azure virtual network, it would be possible to do that. However, the default limitation for virtual networks and local networks is 10 per subscription, you can request
an increase limitation by following the article below:
http://azure.microsoft.com/blog/2014/06/04/azure-limits-quotas-increase-requests/
If you have anything unclear, please feel free to let me know.
Best regards,
Susie
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

How to manage traffic of livestreams or youtube

Hi all,
at the moment we are discussing about how to control or limit traffic used by livestreams. At the moment there are many web pages with livestreams of the olympic winter games and customers facing very high traffic by hd videostreams.
So we are now thinking about managing this videostreams by implementing some policies on the proxies.
And we alternatively think about how to restrict traffic of videostreams or youtube video using asa.
Did not find anything in the knowledgebase. Do you have any hints how to manage this?
thank you in advance and best regards
Vincent

Just go trough Manage application and Modify application and use reindex and full process.
This normally should fix your issue.
Regards
Sorin Radulescu

Enable DirectAccess, Disable VPN

Hi all,
I've just completed the upgrade on my Server 2012 Essentials server to R2 and I'm getting DirectAccess setup.
As my clients are running Enteprise SKU of the OS, I have no reason for the clients to want a SSTP VPN so I'd like to disable the VPN and leave only DirectAccess.
In the instructions for enabling DirectAccess, VPN is a pre-requisite so I don't want to just go and Disable VPN from the Remote Access Management console without knowing if that's going to hose DA first. Does anyone know the answer to this?
Thanks,
Richard
Richard Green MCSE Windows Server 2003, MCTS Desktop Virtualization

You may be able to remove the SSTP ports, without disabling the functionality.
Robert Pearman SBS MVP
itauthority.co.uk |
Title(Required)
Facebook |
Twitter |
Linked in |
Google+

How to snoop traffic on PGW 2200 with Wireshark

How to snoop traffic between PGW 2200 & MGX 8880 with Wireshark?

I hope to have understood correctly your question.
1) enable the snoop on PGW using ./snoop_scrip in /opt/snoop/ path
2) collect the trace of the call and so stop the snoop usinf CTRL C
3) open wireshark
4) drag and drop the files generated from the snoop in wireshark
5) wireshark will ask to merge the file
P.S. PGW uses RUDP to communicate with the media gateway. Set the wireshark RUDP port (in Edit - Preferences - Protocols menu) according to PGW configuration.
Regards.

How disable DHCPv6 & multicast trafic on L2 VLAN ?

Hi all
Windows 7 & Vista send of DHCPv6 packets to multicast MAC 33:33:00:01:00:02 (IPv6 ff02::1:2) and this packets received on interfaces from other VLAN (VLAN L2 without L3 SVIs). Also IPv6 send IGMP membership packets to L2 VLAN too.
How disable it without igmp global turning off?

up

How disable touchpad for hp notebook 14-r204-tu?

how disable touchpad hp notebook 14-r204tu?

Hi ,
Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!
I came across your post about the Notebook, and wanted to assist you! I have looked into your issue about your HP 14-r204tu Notebook and needing to disable your TouchPad on the Notebook. Here is a link that shows you how to do that, instead of settings go to the disable right beside it. Select apply and then ok. To enable the Touchpad just do this in reverse. Hope this helps. Thanks.

6720C :how disable flash when taking picture with ...

hi,please how disable flash when taking picture with camera in 6720?

when camera is open a list pops up here it is
The toolbar provides you with shortcuts to different items and settings before and after capturing an image or recording a video clip. Select from the following: Switch between video and image mode.
Select the scene.
Activate panorama mode.
Turn the video light on (video mode only).
Select the flash mode (images only).
Activate the self-timer (images only).
Activate sequence mode (images only).
Select a colour effect.
Adjust the white balance.
Go to Photos.
scroll to flash and turn it off there
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

ASA5520 v7.2 - How disable VPN traffic?

Similar Messages

Maybe you are looking for