ASDM authenticate fails now

Hello, I need some help getting my ASDM working again.
For some reason when I try used ASDM I can't get pass the authenticate part.
When I try to ssh to the same firewall using the same username and password worked fine no issue.
ASDM version 712-102
Any ideas to get this to work again would be helpful

OK, that will work as long as you have a working RADIUS server configured.
If the RADIUS server cannot be reached, the ASA will fallback to local authentication.
If the RADIUS server is reachable but not authenticating you then the ASA will not fallback to local.
Can you confirm you are using your credentials authenticated by the RADIUS server for ssh? If you are then you should see authentication attempts logged on the RADIUS server when trying to login via ADSM (which uses https).

Similar Messages

On Windows 7 PC, got the "upgrade iTunes" notice, said sure, but the upgrade failed, now I can't access iTunes "invalid permissions"

On Windows 7 PC, got the "upgrade iTunes" notice this morning, said sure, but the upgrade failed, now I can't access iTunes "invalid permissions"
I wasn't paying attention so I don't know the precise error I got on the upgrade failure.
All other iTunes upgrades have been fine...no brainers. Done several on this W7 PC.
If I re-download and install a fresh iTunes I assume I will lose my library...true? Can I find and save off my library so I don't have to "discover" all my music which is scattered all over the PC and a 1T attached USB drive.
Or is there some way to get the iTunes upgrade to successfully restart and install correctly?
Help!

Hello there, Konami84.
The following Knowledge Base article provides some recomendations for troubleshooting:
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Check for .dll files
Go to C:\Program Files (x86)\iTunes and C:\Program Files\iTunes and look for .dll files.
If you find QTMovie.DLL, or any other .dll files, move them to the desktop.
Reboot your computer.
Note: Depending on your operating system, you may only have one of the listed paths.
Uninstall and reinstall iTunes
Uninstall iTunes and all of its related components.
Reboot your computer. If you can't uninstall a piece of Apple software, try using the Microsoft Program Install and Uninstall Utility.
Re-download and reinstall iTunes 11.1.4.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

I ordered my new S5 online and after following the steps outlined in exact order, my old phone no longer works and the S5 will not authenticate. Now I have no phone and I am becoming frustrating.

I ordered my new S5 online and after following the steps outlined in exact order, my old phone no longer works and the S5 will not authenticate. Now I have no phone and I am becoming frustrating.
It downloaded all my contacts, photo's with no problem. I called the number they gave me from my old phone and then turned it off. I then put the sim card in and charged the phone. I followed all the setup steps and no I cannot send any text or make any phone calls. I get a message that they cannot authenticate my phone to dial #8899 but get the same message.

Hello Notahappycamper1962
Let's get that S5 up and running! I want you to love the S5! Is the old device powered off? What zip code are you in?
I look forward to hearing from you and getting this addressed.
JoeL_VZW
Follow us on Twitter @VZWSupport

My 4s wa showing update to iso7 so I updated and it kept failing now its not showing an update at all and saying my iPhone 4S is up todate on USO 6.1.3 help???

My 4s wa showing update to iso7 so I updated and it kept failing now its not showing an update at all and saying my iPhone 4S is up todate on USO 6.1.3 help???

Now it's not showing any update on my phone Iv turne it off and bk on again but still saying software is up to date on 6.1.3

I have got an iphone 3g and when i got it it was jailbroken so i went to restore it but it failed now it says i need to plug it into itunes all the time. what do i do?

i have got an iphone 3g and when i got it it was jailbroken so i went to restore it but it failed now it says i need to plug it into itunes all the time. what do i do?

Kidcomeleon wrote:
i have got an iphone 3g and when i got it it was jailbroken so i went to restore it but it failed now it says i need to plug it into itunes all the time. what do i do?
Plug it into iTunes.

I got the update for iOS 7 on iPad it said not enough room I made room then said failed now it won't offer update

I can not update it was saying I could but not enough room I made room tried to update said failed now says iOS 6.1.3 up to date and no iOS 7 being offered to update what do I do

Do you have the latest version of iTunes installed? I Was able to get to the iOS update after installing the new iTunes, but I had to download it at http://www.apple.com/itunes/

Recently updated to itunes 10.6.1, but during update it says itunes does not have a valid signature and update fails ,now older version is not able to connect to itunes store

Recently updated to itunes 10.6.1, but during update it says itunes does not have a valid signature and update fails ,now older version is not able to connect to itunes store error 306. I am using windows 7.

(Apologies for butting in, wha.)
now older version is not able to connect to itunes store error 306. I am using windows 7.
If you still get the 306 after updating to 10.6.1.7, perhaps try the following user tip:
iTunes for Windows 9.0.x: Error 306

The latest update of my IPhone 3GS has failed, now i can't use the phone. Please help.

The latest update of my IPhone 3GS has failed, now i can't use the phone. I have tried to restore but i get a message saying 'Iphone could not be restored. An unknown error occured(6). I am running the latest version of itunes (10.4) Please help.

Place your iPhone in manual recovery mode or DFU mode.
1. Connect your iPhone
2. Open iTunes
3. Hold down the home and power button for 8 seconds. After 8 sec, let go of the power but still hold down the home button until iTunes recognize your phone in recovery mode

I had a itune update fail, now I get an error message (windows error 2). what do I need to do?

I had an itune update fail. now I get an error message. "windows error 2". I can not open itunes!

With the Error 2, let's try a standalone Apple Application Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of the issue.
Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
http://www.apple.com/itunes/download/
Download and install the free trial version of WinRAR:
http://www.rarlab.com/
Right-click the iTunesSetup.exe (or iTunes64Setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
Go into the folder and doubleclick the AppleApplicationSupport.msi to do a standalone AAS install.
Does it install properly for you?
If instead you get an error message during the install, let us know what it says. (Precise text, please.)

Tryed to update my iphone4s, the update fail, now itunes can not see my phone

tried to update my iphone4s, the update fail, now iTunes can not see my phone

Hi kjpservices,
So it sounds as if your iPhone does not appear in iTune after a failed update to iOS, is that right? In order to get it back into iTunes you will want to use one of these articles, depending on what kind of computer you have -
For a Windows PC, use this -
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
If you are using a Mac, use this -
iOS: Device not recognized in iTunes for OS X
http://support.apple.com/kb/TS1591
Once you get ths iPhone back into iTunes, try the update again. If it fails, post back and we can continue troubleshooting from there.
Thanks for using Apple Support Communities.
Best,
Brett L

HT201263 itouch was updating software and failed, now all i have is a screen showing usb plug and itunes logo,cant reset or restore.help

itouch was updating software and failed, now all i have is a screen showing usb plug and itunes logo,cant reset or restore.help

Type "unable to restore" into the search bar at the top of this page by Support and read the resulting help article

Inital PS CC install failed, now can't uninstall and retry. CC just wants to update PS and fails rep

Inital PS CC install failed, now can't uninstall and retry. CC just wants to update PS and fails repeatedly.

To resolve it, Run the Cleaner tool to remove Ps CC :http://www.adobe.com/support/contact/cscleanertool.html . and then try installing Ps again.
Regards,
Ashutosh

HT1414 i have tried to update my i.phn 3g from 4.1 to 4.2 but it failed and then i tried to restore then its also failed,,now my device is not working,,,can somebody help me?????

i have tried to update my i.phn 3g from 4.1 to 4.2 but it failed and then i tried to restore then its also failed,,now my device is not working,,,can somebody help me?????

No one can help you without knowing the error message and error number when it fails.

Upgrade failed, now iPhone (3gs) in restore mode - help!

Please help!
After syncing my iPhone (3GS) I tried to install new software. Backup went ok, however software upgrade failed, now iTunes states my iPhone is in recovery mode and needs to be restored. this happened last time i tried to upgrade software (before 4.0) and after restore I lost all contacts, photos etc. What actually happens during backup - one would assume that all the data goes somewhere so that you have a 'backup'????
Yours hopefully
Lindsey :0(

Hi...there IS a backup available to you. If you have "dropped" everything, by for example, pressing the Reset all to factory settings, then everything is gone.....but it is on your friendly computer under iTunes! Highlight your phone in the left column and in iTunes, when it shows your phone data, click on the CTRL and mouse click.....this gives you a pop up window, that gives you the chance to revert to the saved info and woohoo....it will all be back in the phone afterwards!

APEX_LDAP.AUTHENTICATE fails with accented user names after upgrade 4.2.1

Hello,
We have a support contract so I already escalated this to Oracle support (awaiting reply now). But maybe someone else also has this problem.
After the upgrade from APEX 4.1.1 to 4.2.1, one of our users couldn't log in any more into our application environment.
We use authentication against MS Active Directory by calling the APEX_LDAP.AUTHENTICATE function.
It took me some time to track down the problem. Apparently, the person with log in problems had a French character in his name ("é"), and this caused the APEX_LDAP.AUTHENTICATE to fail (it returns false, even when the user name/password are correct!). As a workaround, we replaced the "é" by "e" and now the user can log in again... This used to work fine with APEX 4.1.1!
Any one with the same issue??
Matthias
http://matthiashoys.wordpress.com
Edited by: mhoys on Apr 5, 2013 1:27 PM

Thanks Howard! I don't think our problem is related to the APEX Listener (we are using the older version 1.1.4). When I call the APEX_LDAP.AUTHENTICATE function directly from a PL/SQL block (so by bypassing the web server), the problem remains...
Matthias

ASDM authenticate fails now

Similar Messages

Maybe you are looking for