ASDM_HANDLER problem on multiple context mode

Hello,
Has any anybody seen this error?
On the firewall multiple context I used to jump from one context to another, but now when I log in to the admin context and I try to jump to another context I receive this error. Could no find any bug on release notes for that.

Hi,
I have not personally seen this error before. Though I don't use ASDM that much anyway. We used to have FWSMs in multiple context mode and now have ASAs running multiple context mode and I have never seen this.
Have you checked the situation (as the error message suggests) from the CLI of the ASA to see if there is a lot of ASDM sessions in the "admin" context of the unit?
show asdm sessions
- Jouni

Similar Messages

Remote Access VPN Support in Multiple Context Mode (9.1(2))?

Hi Guys,
I am currently running two Cisco ASA5520 (ASA Version: 9.1(2)) firewalls in Active/Standby failover and was contemplating the option of migrating my remote access VPN to these firewalls. However seeing that the new IOS now support mixed multiple context mode and dynamic routing. Is it safe to ask whether or not Remote Access VPN is now support in this IOS upgrade?
Multiple Context Mode New Features:
Site-to-Site VPN in multiple context mode | Site-to-site VPN tunnels are now supported in multiple context mode.
New resource type for site-to-site VPN tunnels | New resource types, vpn other and vpn burst other, were created to set the maximum number of site-to-site VPN tunnels in each context.
Dynamic routing in Security Contexts | EIGRP and OSPFv2 dynamic routing protocols are now supported in multiple context mode. OSPFv3, RIP, and multicast routing are not supported.
New resource type for routing table entries | A new resource class, routes, was created to set the maximum number of routing table entries in each context. We modified the following commands: limit-resource, show resource types, show resource usage, show resource allocation. We modified the following screen: Configuration > Context Management > Resource Class > Add Resource Class.
Mixed firewall mode support in multiple context mode | You can set the firewall mode independently for each security context in multiple context mode, so some can run in transparent mode while others run in routed mode. We modified the following command: firewall transparent. You cannot set the firewall mode in ASDM; you must use the command-line interface. Also available in Version 8.5(1).
Regards,
Leon

Hey Leon,
According to the ASA 9.1 Configuration Guide, Remote Access VPN is not yet supported with version 9.1(2). Only Site-to-Site VPN support in multiple context was introduced with release ASA 9.0(x). This was mentioned in the 9.0(x) release notes.
Regards,
Dennis

Problem using multiple contexts in same thread

Hello,
I am having problem using multiple contexts in the same thread. Here is the scenario:
front-end is calling a ejb1 with a user1 and password. Ejb1 is then calling ejb2
using user2 and password. I am getting security exception when calling ejb2 with
the message user1 is not authorized. Looking at the documentation, context 2 should
be pushed on stack on top of context 1 and context 2 should then be used until
context.close() is called. It looks like this is not the case in this scenario?
Regards,
Jeba Bhaskaran

I have the GTX670. So pretty much the same.
When I go to Edit>Preferences>Playback I see:
When I select the monitor I am not currently using for Premiere Pro, the Program Monitor shows up full size at 1920X1080 in that monitor.
While that may not help you, at least you know a similar card can do the job and you know that it should work.. What happens if you drop down to two monitors? Will it work then?
Also, have you performed the hack that allows Premiere Pro to use the card since that card is not in the file? I have no idea if that is relevant at all, by the way. It is just an attempt at getting our systems to work the same way.

Explain about transparent mode, single mode, multiple context mode

You can explain about the differents of transparent mode, single mode, multiple context mode in ASA 5500? Thank you very much.

Great question. Hope the below helps:
Transparent Mode: In this mode, the ASA will filter traffic without requiring L3 on the ASA. This means that in your config you will not put IPs on the interfaces to be used for traffic filtering. Thus, filtering is transparent to the traffic as the traffic isn't directly routed to the firewall. Think of it like you have a server plugged into a switch. In transparent mode, you place the ASA between the server and the switch and no configuration change is required to the server. In routed mode, you place the ASA in the same physical location between the server and switch, but have to change the server to use the ASA as a default gateway.
Single Mode: Default mode of an ASA. The ASA acts as a single firewall and all interfaces are provisioned to be managed through a single firewall configuration.
Multiple Context Mode: The ASA is split into multiple virtual configurations. With the ASA now virtualized, you provision the physical interfaces on the ASA to the virtual firewall configured. Each context has it's own configuration seperate from the rest of the firewall. Multi-context is meant for enterprises to invest in a single piece of hardware and scale it for use as multiple security devices.
Hope this helps. Let me know if you have anymore questions!
-Mike
http://cs-mars.blogspot.com

Support IPSec VPN Client in ASA Multiple Context Mode

I've looked at under "Cisco ASA Series CLI Configuration Guide, 9.0" on "Configuring Multiple Context Mode", it says
"IPsec sessions—5 sessions. (The maximum per context.) ". Does it mean in ASA Multiple Contest Mode support IPSec VPN Client? I just want to confirm it because I can't seem find any doc that clearly spell it out. I'll appreciate anyone who can clarify it.
Thank Jason.
( Please direct me to the right group if I'm not for the first time I post it in the Cisco support forum)

This is from the v9.3 config-guide:
Unsupported Features
Multiple context mode does not support the following features:
Remote access VPN. (Site-to-site VPN is supported.)

SSLVPN/webvpn in multiple context mode?

We already know that ASA 9.0 supports site-to-site VPN in multiple context mode. But remote access VPN isn't supported. Obviously, SSL-VPN is a very important feature for most multi-tenant deployment scenarios where each context acts as a border firewall towards the Internet for each tenant. The alternative to terminate all tenant remote-access VPNs in one context means that each tenant would have to be routable from the ASA, which of course isn't a reasonable requirement in most cases.
So, what I'd like to do is to deploy an ASA cluster, and provide remote access VPNs for each tenant, where the connectivity for each remote access group can be addressed with whatever IP address space, and that goes into it's own VRF in the back-end.
As far as I can tell, this isn't doable with the ASA, since multiple context mode prohibits the use of remote access VPN, and I can't think of any other work-around than either having individual firewalls running in single context mode for each tenant, or demand that all tenants are interoperable routing-wise and configure a separate ip address pool in a single context mode for each tenant.
Essentially, there's no good way to implement this with multiple virtual firewalls, using cisco firewalls? Or am I missing something?

If you set up a pair of single-context ASAs for VPN termination, configure a group policy per customer and use the 'Restrict access to VLAN' feature, you could separate customers' traffic and still just use one FW pair for all customers. This pair would connect to the same switch infrastructure as your multi-context edge firewall and thus allow a consolidated solution.
Sent from Cisco Technical Support iPad App

Are VPN Clients supported in multiple context mode?

Hi,
Recently our company has bought two Cisco ASA 5515-X firewalls for at our datacenter. I am new on configuring a Cisco ASA but sofar things are looking good. I have configured them both with HA (active/active) in multiple context mode. Currently they host two security contexts.
I want to configure VPN Client functionallity for Remote Access. As far as I know they come with two user licenses. But there is no VPN Client wizard available and I can't find a way to enable it.
- Is VPN Client supported in Multiple Context mode?
- What is AnyWhere Essentials vs Premium Peers?
Boudewijn
Here is some additional output fromt he current configuration:
Cisco Adaptive Security Appliance Software Version 9.1(2) <context>
Device Manager Version 7.1(3)
Encryption hardware device : Cisco ASA-55xx on-board accelerator (revision 0x1)
                             Boot microcode        : CNPx-MC-BOOT-2.00
                             SSL/IKE microcode     : CNPx-MC-SSL-PLUS-T020
                             IPSec microcode       : CNPx-MC-IPSEC-MAIN-0024
                             Number of accelerators: 1
Baseboard Management Controller (revision 0x1) Firmware Version: 2.4
Licensed features for this platform:
Maximum Physical Interfaces       : Unlimited      perpetual
Maximum VLANs                     : 100            perpetual
Inside Hosts                      : Unlimited      perpetual
Failover                          : Active/Active perpetual
Encryption-DES                    : Enabled        perpetual
Encryption-3DES-AES               : Enabled        perpetual
Security Contexts                 : 2              perpetual
GTP/GPRS                          : Disabled       perpetual
AnyConnect Premium Peers          : 2              perpetual
AnyConnect Essentials             : Disabled       perpetual
Other VPN Peers                   : 250            perpetual
Total VPN Peers                   : 250            perpetual
Shared License                    : Disabled       perpetual
AnyConnect for Mobile             : Disabled       perpetual
AnyConnect for Cisco VPN Phone    : Disabled       perpetual
Advanced Endpoint Assessment      : Disabled       perpetual
UC Phone Proxy Sessions           : 2              perpetual
Total UC Proxy Sessions           : 2              perpetual
Botnet Traffic Filter             : Disabled       perpetual
Intercompany Media Engine         : Disabled       perpetual
IPS Module                        : Disabled       perpetual
Cluster                           : Disabled       perpetual
This platform has an ASA 5515 Security Plus license.

Hi,
No form of VPN Client is supported when you are using an ASA in Multiple Context mode.
The only type of VPN supported in the newer 9.x softwares is L2L VPN / Site to Site VPN
This might answer the VPN Licensing related question
http://packetpushers.net/cisco-asa-licensing-explained/
I never seem to remember it exactly myself even.
- Jouni

Dynamic Routing Protocol Support in Cisco ASA Multiple Context Mode

                   Dear Experts,
Wold like to know whether dynamic Routing Protocol Support in Cisco ASA Firewall Multiple Context Mode. If yes then please provide OS version and Hardware Model of Cisco ASA Firewall. Appreciate the quick response. Thanks.

Hi,
Check out this document for the information
http://www.cisco.com/en/US/docs/security/asa/roadmap/asa_new_features.html#wp93116
Its lists the following for software level 9.0(1)
Multiple   Context Mode Features
Dynamic routing in Security   Contexts
EIGRP and OSPFv2 dynamic   routing protocols are now supported in multiple context mode. OSPFv3, RIP, and multicast routing   are not supported.
Seems to me you would need some 9.x version to support the above mentioned Dynamic Routing Protocols.
I don't think its related to the hardware model of the ASA other than that it requires a model that supports Multiple Context Mode. To my understanding the only model that doesnt support that is ASA5505 of the whole ASA5500 and ASA5500-X series.
Hope this helps
- Jouni

Active/standby in multiple context mode

is active/standby configuration possible in multilple context mode? i cannot find an article regarding this matter.

Hello John,
It is available
Actually the ones you need are the regular ones (documents) as the ASA will trigger failover if one of the context fail
Important Notes
For multiple context mode, the ASA can fail over the entire unit (including all contexts) but cannot fail over individual contexts separately.
. Active/Standby Failover is available on units that run in either single or multiple context mode. Both failover configurations support stateful or stateless (regular) failover.
VPN failover is not supported on units that run in multiple context mode as VPN is not supported in multiple context. VPN failover is available only for
Active/Standby Failover configurations in single context configurations.
With this I think you are ready to start configuring it:
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00807dac5f.shtml
Julio

Multiple context mode and Active Active

Hi Everyone,
ASA in multiple context mode works as active active mode.
ASA has 2 contexts admin and x.
We have 2 physical ASA say ASA1 and ASA2 .
Under system context we have hostname ASA
When i ssh to ASA1 it brings the ASA/admin mode.
sh failover shows
sh failover shows
This host: Primary
This host: Primary
When i try to login to ASA 2 it brings me to ASA/x prompt.
sh failover shows
This context: Active
Peer context: Standby Ready
Need to know is there any way that i can login to other physical ASA?
i hope my question makes sense.
Message was edited by: mahesh parmar

Hi Mahesh,
To it seems that you are logging to different contexts in these 2 cases.
Normally an admin always logs to the "admin" context IP address owned either by the primary IP address for the Active unit or the secondary IP address for the Standby unit.
So what I would suggest you do first is that you go to the context "admin" and issue the command "show run interface"
Then go to the context "x" and issue the command "show run interface"
Now check the IP addresses on the interfaces.
Especially the interface on the "admin" context should contain an IP address for both of the ASA units. Check the interface IP address which originally lead you to the "admin" context.
For example
ip address 10.10.10.1 255.255.255.0 standby 10.10.10.2
If the above were true you would connecto the IP address 10.10.10.1 when you wanted to connect to the Active unit and use the IP address 10.10.10.2 when you wanted to connect to the current Standby unit
- Jouni

Botnet Filter with multiple Context Mode

We used the Botnet Filter in Single Context Mode for a long Time. Now we converted to multiple Context Mode and the Database is no longer updated. In the system Context I can See the update settings but when I try to update the result is always "no DNS server". Since the system context has no interfaces there are no DNS settings etc.
How should be the Botnet Filter configured in Multiple Context Mode?
Thanks for any response in advance.

sh run | grep dns
dns domain-lookup T-COM
dns domain-lookup COLT
dns server-group DefaultDNS
policy-map type inspect dns preset_dns_map
inspect dns preset_dns_map
ping update-manifests.ironport.com
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 204.15.82.17, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 160/162/170 ms
ping updates.ironport.com
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 80.239.221.64, timeout is 2 seconds:
ASA Version 8.4(2)
hostname DE-VM-TER-FW-02
enable password 8Ry2Yj8765U24 encrypted
passwd 2KFQnb6IdI.2KY75 encrypted
names
interface GigabitEthernet0/0.3207
nameif TR_v207
security-level 50
ip address 10.28.6.60 255.255.255.248
interface GigabitEthernet0/0.3208
nameif TR_v208
security-level 70
ip address 10.28.6.68 255.255.255.248
interface GigabitEthernet0/0.3209
nameif TR_v209
security-level 80
ip address 10.28.6.76 255.255.255.248
interface GigabitEthernet0/0.3210
nameif TR_v210
security-level 90
ip address 10.28.6.84 255.255.255.248
interface GigabitEthernet0/1
nameif COLT
security-level 0
ip address 217.111.58.46 255.255.255.240
interface GigabitEthernet0/3
nameif T-COM
security-level 0
ip address 194.25.250.94 255.255.255.240
dns domain-lookup T-COM
dns domain-lookup COLT
dns server-group DefaultDNS
name-server 8.8.8.8
object network COLT_dynamic_NAT
subnet 0.0.0.0 0.0.0.0
object network T-COM_dynamiy_NAT
subnet 0.0.0.0 0.0.0.0
object-group network DM_INLINE_NETWORK_1
network-object 10.0.0.0 255.0.0.0
network-object 172.16.0.0 255.240.0.0
network-object 192.168.0.0 255.255.0.0
access-list COLT_access_in extended deny ip any any
access-list T-COM_access_in extended permit tcp any object DEUAG01-actsync eq https
access-list T-COM_access_in extended permit tcp any object DEUAG01-portal eq https
access-list T-COM_access_in extended deny ip any any
access-list TR_3208_access_in extended deny ip any object-group DM_INLINE_NETWORK_1
access-list TR_3208_access_in extended permit ip any any
access-list TR_3208_access_in extended permit icmp any any
access-list TR_v207_access_in extended deny ip any any
access-list TR_v210_access_in extended deny ip any any
access-list TR_v209_access_in extended deny ip any any
pager lines 24
logging enable
logging asdm informational
mtu TR_v208 1500
mtu T-COM 1500
mtu COLT 1500
mtu TR_v207 1500
mtu TR_v210 1500
mtu TR_v209 1500
ip verify reverse-path interface T-COM
ip verify reverse-path interface COLT
ipv6 access-list TR_v207_access_ipv6_in deny ip any any
ipv6 access-list TR_v208_access_ipv6_in deny ip any any
ipv6 access-list TR_v209_access_ipv6_in deny ip any any
ipv6 access-list TR_v210_access_ipv6_in deny ip any any
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
object network COLT_dynamic_NAT
nat (any,COLT) dynamic interface
object network T-COM_dynamiy_NAT
nat (any,T-COM) dynamic interface
access-group TR_3208_access_in in interface TR_v208
access-group TR_v208_access_ipv6_in in interface TR_v208
access-group T-COM_access_in in interface T-COM
access-group COLT_access_in in interface COLT
access-group TR_v207_access_in in interface TR_v207
access-group TR_v207_access_ipv6_in in interface TR_v207
access-group TR_v210_access_in in interface TR_v210
access-group TR_v210_access_ipv6_in in interface TR_v210
access-group TR_v209_access_in in interface TR_v209
access-group TR_v209_access_ipv6_in in interface TR_v209
route T-COM 0.0.0.0 0.0.0.0 194.25.250.81 1
route COLT 0.0.0.0 0.0.0.0 217.111.58.33 20
route TR_v208 10.28.24.0 255.255.255.0 10.28.6.65 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
user-identity default-domain LOCAL
no snmp-server location
no snmp-server contact
telnet timeout 5
ssh timeout 5
no threat-detection statistics tcp-intercept
dynamic-filter use-database
dynamic-filter enable interface T-COM
dynamic-filter enable interface COLT
dynamic-filter drop blacklist interface T-COM
dynamic-filter drop blacklist interface COLT
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect dns preset_dns_map dynamic-filter-snoop
service-policy global_policy global
Cryptochecksum:7bbe975fb39e189e99d8878787a0037
: end
System Context
dynamic-filter updater-client enable
Can't resolve update-manifests.ironport.com, make sure dns nameserver is configured

Problem with Multiple Context Creation

Hi,
We are facing a java.lang.SecurityException Invalid Subject
We need to create multiple Initial Contexts for a single thread.
Following is the Scenario
1) The user will access Servlet/Struts Action class which performs database call and EJB(one, two) calls with different Initial Contexts ( Credentials are different)
2) At the same time the Timer Task runs in back ground which is invoked from servlet load-on-startup and runs for every 1 min.
3) The Timer Task invoke an MDB this MBD will make an external EJB (three) call for business logic.
{color:#ff0000}Please Suggest me the Sequence of step I am expecting are correct or not{color}
1) The Timer Task will run in the same JVM where the Servlet/Action classes are loaded (WEB-CONTAINER)
2) The Thread created for Servlet/Action class will not be shared by Timer Task.
3) The Thread created for Timer Task and the MDB are different.
4) So the Servlet - Thread, Timer Task Thread and MDB Thread are different.
The Behavior of the Context is as follows according to Bea Document.
[http://e-docs.bea.com/wls/docs81/jndi/jndi.html#476864]
JNDI Contexts and Threads
How to Avoid Potential JNDI Context Problems (Please Refer this Paragraph)
I am closing the entire Context's immediately after lookup
Still we are facing this java.lang.SecurityException Invalid Subject Exception Problem
The Context of EJB which we are calling from MDB is sharing the Servlet/Action Class Context -- Credentials
Example_
{color:#ff0000}Servlet/Action Class Context Credentials -- are user1/pass1{color}
{color:#ff0000}EJB (three) Context Credentials -- are user3/pass3{color}
When EJB (Three) lookup is invoked it’s throwing the following Exception
*java.lang.SecurityException: [Security: 090398] Invalid Subject: user1*
Please advise to solve this problem
Thank You.

Solved By myself
There is problem while passing data to internal table for item level

Multiple context mode, how to download the packet capture file

Hi guys,
Is there a way to download the packet capture file from a specific context? I know that I used to use https://<ASA_IP>/admin/capture/<capture> to download it if it is just one context.
The ASA uses mgmt 0/0 for management and it is connected in a separate OOB network. Only this network has TFTP servers for uploading the capture file. The context in question is in transparent mode. Its IP doesn't have access to any TFTP server.
Thanks!
Difan

Hello Difan,
Please refer the following document.
https://supportforums.cisco.com/document/69281/asa-using-packet-capture-troubleshoot-asa-firewall-configuration-and-scenarios
Also what version of the ASA code are you using?
Regards,
Jai Ganesh K

ASA5540 in multiple-context SNMP/icmp doesn´t work

Hi there,
     I need some help in order to understante what´s going on with an asa540 configure in multiple-context mode.
     I Have a cacti server on my lan and now I´m try to monitoring the interface with snmp. When I try to get this information returns the error message:
     CISCOASA/CONTEXTA#
     JUN 11 2013 01:52:00: %ASA-1-1-6021: Deny UDP reverse path check from 10.6.6.6 to IP_SRV_CACTI on interface inside
    JUN 11 2013 01:52:01: %ASA-1-1-6021: Deny UDP reverve path check from 10.6.6.6 to IP_SRV_CACTI on interface inside
     If I try to ping returns the same error:
     CISCOASA/CONTEXTA#
     JUN 11 2013 01:56:09: %ASA-1-1-6021: Deny icmp reverse path check from 10.6.6.6 to IP_SRV_CACTI on interface inside
    Following attached the conf of my asa
My question is Why I can´t ping or even use snmp ???
   If anyone could me help with a tip or a document about it ...
   My best regards
   Adriano

CISCOASA/CONTEXT# packet-tracer input inside icmp 10.132.0.25 8 0 10.6.72.2
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list
Phase: 2
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   10.6.72.2       255.255.255.255 identity
Phase: 4
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   IP_SRV_HSLCACTIP01 255.255.255.255 inside
Phase: 5
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
Phase: 6
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 7
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:
Phase: 9
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 453866627, packet dispatched to next module
Phase: 10
Type: ROUTE-LOOKUP
Subtype: output and adjacency
Result: ALLOW
Config:
Additional Information:
found next-hop 0.0.0.0 using egress ifc identity
adjacency Active
next-hop mac address 0000.0000.0000 hits 22196
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: inside
output-status: up
output-line-status: up
Action: allow
Route information:
route inside 10.132.0.0 255.255.252.0 10.6.72.1 1
route inside IP_SRV_HSLCACTIP01 255.255.255.255 10.6.72.1 1
CISCOASA/CONTEXT# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route
Gateway of last resort is 200.206.50.233 to network 0.0.0.0
C    200.206.50.232 255.255.255.248 is directly connected, outside
S    10.132.0.0 255.255.252.0 [1/0] via 10.6.72.1, inside
S    IP_SRV_HSLCACTIP01 255.255.255.255 [1/0] via 10.6.72.1, inside
S*   0.0.0.0 0.0.0.0 [1/0] via 200.206.50.233, outside
Regards,

ASA 5512-X version 9.1 multiple contextes supported?

Hi All,
could soumeone please let me know if on the ASA 5512-X virtual contexts are supported with version 9.1 ?
I found different information on the Cisco web, the ASA datasheet says it is supported but in the configuration guide I found exactly the opposite information.
Cisco ASA Series General Operations CLI Configuration Guide 9.1 and 8.6
http://www.cisco.com/en/US/docs/security/asa/asa91/configuration/general/ha_contexts.html#wp1188797
http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/interface_start.html#wp1329030
Cisco ASA 5500 and ASA 5500-X Series Next- Generation Firewalls for Small Offices and Branch Locations Data Sheet (Updated)
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/data_sheet_c78-701253.html
thanks in advance
Best Regards
Frank

Hi,
you find the information in the ASA Configuration Guide section "Licensing Requirements for Multiple Context Mode"
http://www.cisco.com/en/US/docs/security/asa/asa91/configuration/general/ha_contexts.html#wp1188797
http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/interface_start.html#wp1329030
Licensing Requirements for Multiple Context Mode
ASA 5512-X No support.
Best Regards
Frank

ASDM_HANDLER problem on multiple context mode

Similar Messages

Maybe you are looking for